This document provides instructions for removing and disassembling components of the fuel injection system and turbocharger on a Caterpillar 3064 engine. The procedure includes removing the fuel injection pump by loosening mounting bolts and oil lines, and removing the turbocharger by disconnecting hoses and oil lines and loosening nuts. The turbocharger can then be disassembled by removing bolts from oil lines and gaskets.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjskkksmemm
This document is an operation and maintenance manual for a Doosan DL420 wheel loader. It provides information on the intended use of the machine, its components like the engine, transmission, braking and hydraulic systems. It also describes the cabin, FOPS and ROPS safety structures. The manual discusses CE marking requirements and installing communication equipment safely. Product plates for identifying the machine and components are shown.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 3064 or 3066 engine. It includes illustrations and steps to remove the threaded plug and shim that contain the valve from the cylinder block. Proper cleaning and containment of fluids is emphasized. The summary is completed in 3 sentences or less.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjskkksmemm
This document is an operation and maintenance manual for a Doosan DL420 wheel loader. It provides information on the intended use of the machine, its components like the engine, transmission, braking and hydraulic systems. It also describes the cabin, FOPS and ROPS safety structures. The manual discusses CE marking requirements and installing communication equipment safely. Product plates for identifying the machine and components are shown.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 3064 or 3066 engine. It includes illustrations and steps to remove the threaded plug and shim that contain the valve from the cylinder block. Proper cleaning and containment of fluids is emphasized. The summary is completed in 3 sentences or less.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 325 d fm excavator (prefix c8l) service repair manual (c8l000...fjjskekdmme
This document provides instructions for removing and installing the camshaft and related components on a Caterpillar C7 engine. It describes:
1. Removing the camshaft by first removing other components like the vibration damper, pulley, rocker arms and pushrods.
2. Removing the camshaft gear by pressing it off the camshaft and removing any keys.
3. Removing the camshaft bearings using a special tool, noting the oil hole orientations.
4. Installing the camshaft bearings and gear, aligning oil holes and keys before reinstalling the camshaft.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat c2.2 industrial engine (prefix g7 m) service repair manual (g...ifkkdmdmdm
The document provides instructions for removing and installing the crankshaft pulley and front seal on an industrial engine. It describes removing the pulley by drilling holes in the seal, inserting a puller tool, and removing the woodruff key from the crankshaft. For installation, it instructs to clean components, insert the key, lubricate parts, and tighten the pulley nut to the specified torque. It also describes removing the front housing by removing mounting nuts and identifying locating features.
Caterpillar cat 312 b excavator (prefix 6sw) service repair manual (6sw00001 ...fjsekksmemm
This document provides instructions for removing and installing the camshaft and camshaft gear on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Using a puller tool to remove the camshaft gear after aligning timing marks.
3) Lubricating and carefully installing the camshaft, making sure not to damage lobes or bearings.
4) Cleaning and aligning the camshaft bearings before pressing them into place.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the heavy fuel injection pump from the engine.
3. Removing hoses and bolts to detach the turbocharger, oil lines, and exhaust manifold as a single unit from the engine.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil lines from the turbocharger.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...tuzhiyou2
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...qfyc504378
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...lituo39419496
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the fuel injection pump from the engine block.
3. Removing hoses and lines connected to the turbocharger, then removing nuts to separate the turbocharger from the exhaust manifold.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil supply and return lines.
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...zan2736ban
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Cleaning the crankshaft and applying retaining compound to the mating surfaces.
2) Using a installer tool to push the new seal onto the crankshaft until it bottoms out.
3) Removing the tool and checking that the seal is correctly installed.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...fusjekkdmdmd2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve if needed.
- Removing the crankshaft front seal by drilling holes and pulling it off with a slide hammer puller.
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a sealing compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...f8usejkddmmd
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a retaining compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 325 d fm excavator (prefix c8l) service repair manual (c8l000...fjjskekdmme
This document provides instructions for removing and installing the camshaft and related components on a Caterpillar C7 engine. It describes:
1. Removing the camshaft by first removing other components like the vibration damper, pulley, rocker arms and pushrods.
2. Removing the camshaft gear by pressing it off the camshaft and removing any keys.
3. Removing the camshaft bearings using a special tool, noting the oil hole orientations.
4. Installing the camshaft bearings and gear, aligning oil holes and keys before reinstalling the camshaft.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat c2.2 industrial engine (prefix g7 m) service repair manual (g...ifkkdmdmdm
The document provides instructions for removing and installing the crankshaft pulley and front seal on an industrial engine. It describes removing the pulley by drilling holes in the seal, inserting a puller tool, and removing the woodruff key from the crankshaft. For installation, it instructs to clean components, insert the key, lubricate parts, and tighten the pulley nut to the specified torque. It also describes removing the front housing by removing mounting nuts and identifying locating features.
Caterpillar cat 312 b excavator (prefix 6sw) service repair manual (6sw00001 ...fjsekksmemm
This document provides instructions for removing and installing the camshaft and camshaft gear on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Using a puller tool to remove the camshaft gear after aligning timing marks.
3) Lubricating and carefully installing the camshaft, making sure not to damage lobes or bearings.
4) Cleaning and aligning the camshaft bearings before pressing them into place.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fjskekfseik
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the heavy fuel injection pump from the engine.
3. Removing hoses and bolts to detach the turbocharger, oil lines, and exhaust manifold as a single unit from the engine.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil lines from the turbocharger.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...tuzhiyou2
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...qfyc504378
1) The document provides instructions for removing and installing a fuel injection pump and turbocharger from a Caterpillar 3064 engine.
2) Key steps include removing fuel lines, bolts, and washers to access the pump and turbocharger, and installing replacement gaskets and reattaching all components in reverse order.
3) Technicians are advised to keep components clean, mark parts for alignment during reinstallation, and properly contain fluids.
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Removing bolts and lifting the fuel injection pump from the engine using a hoist.
3. Disassembling the turbocharger by removing hoses, lines, and nuts securing it to the exhaust manifold.
4. Placing alignment marks on turbocharger components before disassembly to aid reassembly. Removing bolts from oil lines.
Caterpillar Cat 312C L Excavator (Prefix DBN) Service Repair Manual (DBN00001...lituo39419496
The document provides instructions for removing and disassembling the fuel injection pump and turbocharger from a Caterpillar 3064 engine. Key steps include:
1. Removing fuel injection lines and cover to access the fuel injection pump. Scribing alignment marks before removal.
2. Using bolts and lifting equipment to remove the fuel injection pump from the engine block.
3. Removing hoses and lines connected to the turbocharger, then removing nuts to separate the turbocharger from the exhaust manifold.
4. Placing identification marks on turbocharger components before disassembly to aid reassembly. Removing bolts to separate oil supply and return lines.
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C and 312C L Excavator (Prefix CBA) Service Repair Manual ...zan2736ban
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Cleaning the crankshaft and applying retaining compound to the mating surfaces.
2) Using a installer tool to push the new seal onto the crankshaft until it bottoms out.
3) Removing the tool and checking that the seal is correctly installed.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...fusjekkdmdmd2w
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using a puller tool and removing the wear sleeve if needed.
- Removing the crankshaft front seal by drilling holes and pulling it off with a slide hammer puller.
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a sealing compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...f8usejkddmmd
The document provides instructions for installing a crankshaft front seal on a 312C L excavator. It describes:
1) Drilling three holes in the old seal and using a slide hammer puller to remove it, being careful not to damage the crankshaft flange.
2) Cleaning the crankshaft flange surface and applying a retaining compound.
3) Using an installer tool to push the new seal into place until it is fully seated on the crankshaft flange.
The summary covers the key steps for removing the old seal and installing the new one in 3 sentences while maintaining the essential details.
Caterpillar Cat 312C L Excavator (Prefix CBA) Service Repair Manual (CBA01201...8ufjsekddm8u
This document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing the crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing the flywheel housing which requires removing bolts and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and tightening the nut to the specified torque.
- Removing the crankshaft front seal by drilling holes and pulling it off, and installing the new seal with a specific tool.
- Removing just the idler gear which involves using pullers after draining fluids and
Similar to Caterpillar cat 312 c excavator (prefix dbn) service repair manual (dbn00001 and up) (13)
Toyota 7 fg45 forklift service repair manualfjskkksmemm
The document provides service information for Toyota forklifts models 7FG/7FD35-45 series, including:
1. An overview of the manual contents and how to use it, with explanations of terminology and abbreviations.
2. Sections covering removal and installation procedures, disassembly and reassembly, inspection points, and tightening torques for major vehicle systems and components.
3. References other repair manuals needed for servicing engines mounted on the vehicles.
Toyota 7 fdu32 forklift service repair manualfjskkksmemm
This manual covers service procedures for Toyota forklifts. It provides 3 main points:
1. It details specifications, components, removal/installation, and inspection/adjustment procedures for the engine, including the 4Y and 1DZ-11 engines.
2. It describes the air cleaner, radiator, muffler, battery, and other engine systems. Specifications, components, and maintenance procedures are outlined.
3. It covers the accelerator pedal, EZ pedal option, vehicle speed control system, and electrical components. Inspection, adjustment, diagnosis and troubleshooting steps are presented.
Toyota 7 fdu30 forklift service repair manualfjskkksmemm
This document provides service procedures for Toyota forklifts. It covers engine removal and installation, inspection and adjustment of various engine components like the air cleaner, radiator, muffler, and battery. Procedures for inspecting and adjusting engine speed on 4Y and 1DZ-11 engines are described. The accelerator pedal, vehicle speed control system, and other controls are also covered. Troubleshooting tips are provided. Standard specifications and component details are included to aid technicians in servicing the forklifts.
Toyota 7 fdu25 forklift service repair manualfjskkksmemm
This manual covers service procedures for Toyota forklifts. It provides 3 main points:
1. It details specifications, components, removal/installation, and inspection/adjustment procedures for the engine, including the 4Y and 1DZ-11 engines.
2. It describes engine-related components like the air cleaner, radiator, muffler, and battery.
3. It covers other engine systems such as the accelerator pedal, vehicle speed control system, and troubleshooting. Concise summaries and point operations are included to highlight key steps and cautions.
Toyota 7 fdu20 forklift service repair manualfjskkksmemm
This manual covers service procedures for Toyota forklifts. It provides 3 main points:
1. It details specifications, components, removal/installation, and inspection/adjustment procedures for the engine, including the 4Y and 1DZ-11 engines.
2. It describes other mechanical systems like the air cleaner, radiator, muffler, and battery.
3. It gives operational tips, terminology, torque specifications, and periodic maintenance schedules to properly service the forklifts. Key details like match marking parts and using special tools are emphasized.
Toyota 7 fdu18 forklift service repair manualfjskkksmemm
This document provides service procedures for Toyota forklifts. It summarizes engine specifications, maintenance, and repair for the 4Y and 1DZ-11 engines. Procedures are outlined for tasks like engine removal and installation, air bleeding, speed inspection and adjustment, maintenance of components like the air cleaner, radiator, and muffler. Safety cautions are provided throughout.
Toyota 7 fdu15 forklift service repair manualfjskkksmemm
This manual covers service procedures for Toyota forklifts. It provides 3 main points:
1. It details specifications, components, removal/installation, and inspection/adjustment procedures for the engine, including the 4Y and 1DZ-11 engines.
2. It describes the air cleaner, radiator, muffler, battery, and other engine systems. Specifications, components, and maintenance procedures are outlined.
3. Throttle and engine speed adjustments are explained, along with idle up speed inspection for the 4Y engine. Diagnosis and repair of the vehicle speed control system are also covered.
Massey ferguson mf165 tractors parts catalogue manualfjskkksmemm
This document provides part numbers and descriptions for components related to engines, electrical equipment, alternators, generators, and starters for Massey Ferguson MF 165/168/185/188 tractors. It includes lists of parts with quantities, part numbers, descriptions and notes for each component. Reference information is provided for each section to cross reference related parts.
Massey ferguson mf158 tractor parts catalogue manualfjskkksmemm
This document provides a parts list and diagrams for the engine and various systems of a Massey Ferguson 155/158 tractor. It includes over 35 individual items related to the engine, electrical equipment, alternator, generator, starter, and other components. Each item lists the part number, quantity, description, and any relevant comments to identify variations or component numbers. The document aims to catalog all relevant parts for servicing and repair of this tractor model.
Massey ferguson mf155 tractor parts catalogue manualfjskkksmemm
This document provides a parts list and diagrams for the engine and various systems of a Massey Ferguson 155/158 tractor. It includes over 35 individual items related to the engine, electrical equipment, alternator, generator, starter, and other components. Each item lists the part number, quantity, description, and any relevant comments to identify variations or component numbers. The document aims to catalog all relevant parts for servicing and repair of this tractor model.
Massey ferguson mf140 tractor parts catalogue manualfjskkksmemm
This document contains parts lists and descriptions for engines, starters, generators, and other accessories for Massey Ferguson 133, 135, and 140 tractors. It includes over 30 parts with descriptions and part numbers. Notes provide additional details about the parts and applicable serial number ranges. The parts are organized into sections for the different components.
Massey ferguson mf135 tractor parts catalogue manualfjskkksmemm
This document contains parts lists and descriptions for engines, starters, generators, and other accessories for Massey Ferguson 133, 135, and 140 tractors. It includes over 30 parts with descriptions and part numbers. Notes provide additional details about the parts and applicable serial number ranges. The parts are organized into sections for the different components.
Massey ferguson mf133 tractor parts catalogue manualfjskkksmemm
This document contains parts lists and descriptions for engines, starters, generators, and other accessories for Massey Ferguson 133, 135, and 140 tractors. It includes over 30 parts with descriptions and part numbers. Notes provide additional details about the parts and applicable serial number ranges. The parts are organized into sections for the different components.
Massey ferguson mf super 90 tractor parts catalogue manualfjskkksmemm
This document contains parts listings and descriptions for a Massey Ferguson MF Super 90 tractor. It includes over 70 items grouped into sections for the cylinder block, crankshaft, pistons, cylinder head, and gasket sets. The parts are listed with part numbers, quantities, and brief descriptions to identify the components for both gas and L.P. fueled versions of the engine.
Massey ferguson mf 6713 r tractor (eco4 tier 2 3 ; br) parts catalogue manualfjskkksmemm
This document contains a table of contents and part listings for an MF 6713R tractor engine. The table of contents lists 19 sections that cover various engine systems and components. Subsequent pages provide part numbers, quantities and descriptions for engine assemblies, the cylinder block, timing gear cover, crankshaft and pistons, camshaft and valve mechanism, cylinder head, intake manifold, turbocharger and exhaust manifold.
Massey ferguson mf 5608 tractor (c339061 h349047) parts catalogue manualfjskkksmemm
The document provides a parts list and technical specifications for the engine of a Massey Ferguson MF 5608 tractor. It contains 27 items with part numbers, quantities, descriptions, and comments. The list is divided into sections covering the cylinder block, timing gear housing, and other engine components. Tolerances or ranges are provided for some part measurements.
Massey ferguson mf 3455 cm crawler type tractor parts catalogue manualfjskkksmemm
This document provides part numbers and descriptions for components of a Massey Ferguson MF 3455 C/CF/CM crawler-type tractor engine. It includes listings for the engine assembly, short engine, cylinder block, camshaft, pistons and connecting rods, end cover, cylinder head, rocker shaft, and fuel injection equipment. Each item lists the part number, quantity, description, and sometimes additional details or replacement part numbers. The purpose is to provide specifications and part listings to aid in repair or replacement of engine components.
This document provides parts information for the engine of Massey Ferguson MF 3455 C/CF/CFM crawler tractors that are Tier 3 compliant. It includes lists of parts for the engine assembly, short engine, cylinder block, camshaft, pistons and connecting rods, end cover, cylinder head, and rocker shaft. Each part is identified by number, part number, quantity, and description. Footnotes provide additional details for some parts.
Massey ferguson mf 3455 cf crawler type tractor parts catalogue manualfjskkksmemm
This document provides part numbers and descriptions for components of a Massey Ferguson MF 3455 C/CF/CM crawler-type tractor engine. It includes listings for the engine assembly, short engine, cylinder block, camshaft, pistons and connecting rods, end cover, cylinder head, rocker shaft, and fuel injection equipment. Each item lists the part number, quantity, description, and sometimes additional details like replacement parts.
This document provides parts information for the engine of Massey Ferguson MF 3455 C/CF/CFM crawler tractors that meet Tier 3 emissions standards. It includes lists of parts for the engine assembly, short engine, cylinder block, camshaft, pistons and connecting rods, end cover, cylinder head, and rocker shaft. Each part is identified by number, part number, quantity, and description.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:14:12 UTC+0800 2020
3/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:15:12 UTC+0800 2020
2/2312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00608136
1. Loosen the hose clamp (1) on hose (2) .
2. Remove hose (2) from the turbocharger (3) .
Illustration 2 g00812846
3. Disconnect oil supply line (4) from the cylinder block.
4. Loosen two clamps (5) on hose (7) .
5. Slide hose (7) off fitting (8) onto oil return line (6) .
2/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00608177
6. Remove eight nuts (9) from the studs on the exhaust manifold.
Note: The four studs have two nuts for a total of eight nuts.
7. Remove turbocharger (3), oil supply line (4), and oil return line (6) as an unit.
8. Remove metal gasket (10) (not shown). Check the gasket for wear or damage. Replace the
gasket, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:16:11 UTC+0800 2020
3/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615171
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
Illustration 1 g00608212
2. Remove two bolts (1) from the oil return line. Remove bolt (2) from the oil supply line.
3. Remove oil return line (3) from the cartridge.
4. Remove oil supply line (4) from the cartridge.
Illustration 2 g00608210
5. Remove gasket (5) from the cartridge.
6. Remove gasket (6) from the turbine housing.
2/4312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00608342
7. Remove the bolt and nut (7) from clamp (8). Remove clamp (8) that secures the turbine
housing (9) to the cartridge (10) .
8. Separate turbine housing (9) from the cartridge (10) .
Illustration 4 g00608415
Illustration 5 g00608452
3/4312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 9. Remove snap ring (11) from compressor housing (12) .
10. Separate compressor housing (12) from the cartridge (10) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:17:10 UTC+0800 2020
4/4312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01147762
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During the assembly procedure, ensure that the index marks are aligned when the
components are assembled.
Illustration 1 g00608452
1/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00608415
1. Install cartridge (10) into compressor housing (12) .
2. Install snap ring (11) into compressor housing (12) .
Illustration 3 g00608342
3. Install cartridge (10) into turbine housing (9) .
4. Install clamp (8) that secures cartridge (10) and turbine housing (9) together. Install the bolt
and nut (7) into clamp (8).
Note: Refer to the Specifications Module, "Turbocharger" for information on the clamp.
2/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00608210
5. Inspect the condition of the gaskets. Replace the gaskets, if necessary.
6. Install gasket (6) on the turbine housing.
7. Install gasket (5) on the cartridge.
Illustration 5 g00608212
8. Place oil supply line (4) in position. Secure the oil supply line with bolt (2) (not shown).
9. Place oil return line (3) in position. Secure the oil return line with two bolts (1) .
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:18:09 UTC+0800 2020
3/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564587
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of all gaskets. Replace the gaskets, if necessary.
Illustration 1 g00608177
1/2312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 2. Install metal gasket (10) (not shown). Install turbocharger (3), oil supply line (4) and oil
return line (6) (not shown) as a unit.
3. Install eight nuts (9). Tighten the nuts to a torque of 41 N·m (30 lb ft).
Note: Two nuts are installed on each turbocharger mounting stud.
Illustration 2 g00812846
4. Slide hose (7) down the oil return line (6) onto fitting (8) .
5. Tighten two clamps (5) on hose (7) .
6. Connect oil supply line (4) to the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:19:09 UTC+0800 2020
2/2312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565722
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00605454
1/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Remove the nuts (1) and washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2. Remove exhaust manifold (2) from the cylinder head assembly.
3. Remove exhaust manifold gasket (3) that is located between exhaust manifold (2) and the
cylinder head assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00605454
1. Install exhaust manifold gasket (3) between exhaust manifold (2) and the cylinder head
assembly.
Note: The 3066 Engine has two exhaust manifold gaskets, while the 3064 Engine has one
exhaust manifold gasket.
2. Place exhaust manifold (2) in position on the cylinder head.
3. Install the nuts (1) and the washers that secure the exhaust manifold to the cylinder head
assembly. The 3066 Engine has twelve nuts and washers while the 3064 Engine has eight
nuts and washers.
2/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 4. Tighten exhaust manifold nuts (1) to a torque of 18 ± 4 N·m (13 ± 3 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:20:08 UTC+0800 2020
3/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615211
Air Inlet Heater - Remove and Install
SMCS - 1090-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611147
1. Loosen hose clamp (1) that secures air inlet hose (2) to air inlet elbow (4) .
2. Disconnect air inlet hose (2) from air inlet elbow (4) .
1/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 3. Remove four bolts (3) and washers that secure the following items to the air inlet manifold:
air inlet elbow (4), gasket (5), air inlet heater (6) and gasket (7) .
Illustration 2 g00611165
4. Remove the following items from the air inlet manifold: air inlet elbow (4), gasket (5), air
inlet heater (6) and gasket (7) .
Note: Check the condition of the gaskets that are used between the elbow and the air inlet
heater. Check the gaskets between the air inlet heater and the air inlet manifold. If the
gaskets are damaged in any way, replace the gaskets.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g00611165
Note: Check condition of the gaskets for the air inlet elbow and the air inlet heater. If the
gaskets are damaged, use a new part for replacement. The wire mesh gasket (7) is installed
between the air inlet manifold and the air inlet heater.
1. Place the following items in position on the air inlet manifold: gasket (7), the air inlet heater
(6), gasket (5) and the air inlet elbow (4) .
Illustration 4 g00611147
2. Install four bolts (3) that secure the following items to the air inlet manifold: gasket (7), the
air inlet heater (6), gasket (5) and the air inlet elbow (4)
Tighten bolts (3) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
3. Connect air inlet hose (2) to air inlet elbow (4) .
4. Tighten hose clamp (1) that secures the air inlet hose to the air inlet elbow.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 12 22:21:08 UTC+0800 2020
3/3312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312C EXCAVATOR DBN
Configuration: 312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01575215
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
A. Remove fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
B. Remove fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
C. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2312C & 312C L Excavators DBN00001-UP (MACHINE) POWERED BY 3064 Engin...
2020/5/12https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...