The document provides instructions for installing a cylinder head on a 3054 engine used in Caterpillar 312B and 312B L excavators. The steps include: cleaning the cylinder block and head, installing the cylinder head gasket, placing the head and tightening the bolts in sequences, and further tightening specific bolts using a degree wheel. Additional components are then reinstalled to complete the job.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01645901
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
1. Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores.
Illustration 1 g00550165
1/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head
gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder
head gasket.
3. Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 4.
Illustration 2 g00550163
Typical example
4. Attach a suitable lifting device to cylinder head (2) .
5. Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on
dowels (4) and that cylinder head gasket (3) is positioned correctly.
6. Remove Tool (A) .
Illustration 3 g00550160
Typical example
7. Lubricate cylinder head bolts (1) with clean engine oil.
2/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00550162
8. Gradually tighten all of the bolts (1 through 22) in a numerical sequence to a torque of 110
N·m (80 lb ft).
9. Tighten all of the bolts (1 through 22) again in a numerical sequence to a torque of 110 N·m
(80 lb ft).
10. Place an index mark on the bolts and use Tool (B) in order to further tighten the bolts. Refer
to illustration 4.
a. Turn the short bolts that are marked with an "S" for an additional 150 degrees (2.5
flats).
b. Turn the medium length bolts that are marked with an "M" for an additional 180
degrees (3.0 flats).
c. Turn the long bolts that are marked with an "L" for an additional 210 degrees (3.5
flats).
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Install".
b. Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Install".
c. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
d. Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Install".
e. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
f. Install the inlet manifold. Refer to Disassembly and Assembly, "Air inlet Manifold -Install".
3/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. g. Fill the coolant system. If the engine uses Extended Life Coolant (ELC), refer to Operation
and Maintenance Manual, "Cooling System Coolant (ELC) - Change". If the engine uses
Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual,
"Cooling System Coolant (DEAC) - Change".
h. Connect the electrical connections at the battery.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 23:25:29 UTC+0800 2020
4/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01745933
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00540954
1. Use Tooling (A) to remove lifters (1).
Note: Ensure that the lifters are marked with the appropriate cylinder number for
installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g00540954
1. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are seated correctly and that the lifters are in the correct
cylinders.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 23:26:28 UTC+0800 2020
3/3312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01164529
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Remove".
B. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
C. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
D. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
Illustration 1 g00546803
2. Remove thrust washer (1). Make a note of the location of the hollow dowel (X) for
installation purposes.
Illustration 2 g00546869
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 3. Carefully remove camshaft (2) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00546869
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: Ensure that camshaft (2) is clean. Lubricate camshaft (2) with clean engine oil prior
to installation.
1. Carefully install camshaft (2) in the engine.
3/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g00546803
2. Put thrust washer (1) in position. Make sure that thrust washer (1) is aligned with hollow
dowel (X) .
End By:
a. Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
c. Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Install".
d. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 23:27:28 UTC+0800 2020
4/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i03140046
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A
1U-6671 Puller Gp 1
8S-4712 Bolt 2
1P-0510 Driver Group 1
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
1/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00541128
1. Rotate the crankshaft until the timing marks on the crankshaft gear, the camshaft gear, and
the fuel injection pump gear are aligned, as shown.
Note: The timing marks on the idler gear may not be aligned. This is caused by the
difference in the speed of the rotation of the idler gear.
Illustration 2 g00541130
2. Remove bolt (1) and the washer from the camshaft gear (2).
2/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00541131
3. Install Tooling (A) and remove camshaft gear.
Note: Do not lose the key from the camshaft gear.
4. Inspect the camshaft gear for wear and damage. Replace the gear, if necessary.
Installation Procedure
Illustration 4 g00541130
1. Install camshaft gear (2) in the front housing.
Note: When you install the camshaft gear, ensure that the teeth that have the timing marks
are facing toward the front. Also, ensure that the key is aligned properly in the keyway. If
necessary, tap the gear with a soft hammer in order to seat the key in the keyway.
2. If necessary, remove the idler gear in order to align the gear teeth correctly.
3. Install the washer and bolt (1) on the camshaft gear. Tighten bolt (1) to a torque of 95 N·m
(70 lb ft).
Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the fuel
injection pump gear are aligned.
3/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 4. If a new camshaft gear is used, check the backlash of the camshaft gear. The minimum
backlash for a new gear is 0.08 mm (0.003 inch).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 23:28:27 UTC+0800 2020
4/4312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i06043534
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and
Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the
correct procedure.
B. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01270437
1. Inspect camshaft bearing (1) . Refer to Specifications, "Camshaft Bearings" for more
information.
2. For worn or damaged camshaft bearing (1) use Tooling (A) in order to remove the camshaft
bearing from the cylinder block.
Note: Remove the camshaft bearing from the front of the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bearing housing in the cylinder block. Ensure that the oil holes in the bearing
housing are free from debris.
2/3312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01266512
2. Lubricate the bearing housing in the cylinder block with clean engine oil.
3. Accurately align two Oil Holes (X) in camshaft bearing (1) with the two oil holes in the
cylinder block.
Note: Groove (Y) in the camshaft bearing must be to the top of the cylinder block.
4. Use Tooling (A) in order to install camshaft bearing (1) into the cylinder block. Install the
camshaft bearing so that the front edge of the bearing is flush with the face of the recess in
the cylinder block.
Note: Ensure that all oil holes are correctly aligned. If the oils are not correctly aligned, the
camshaft bearing should be removed.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install"
for the correct procedure.
b. If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and
Assembly, "Balancer - Install". If the engine is not equipped with a balancer, install the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 23:29:26 UTC+0800 2020
3/3312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02974660
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01870497
Typical Example
2/6312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01871553
Note: The engine may be equipped with an oil drain plug or the engine may be equipped
with a drain valve.
1. If equipped, remove drain plug (2) and the O-ring seal. If equipped, open drain valve (5) by
turning handle (6) counterclockwise. Drain the engine oil into a suitable container for
storage or disposal.
2. If necessary, remove drain valve (5) from adapter (7) . If necessary, remove adapter (7)
from engine oil pan (3) .
Note: In order to remove a oil pan, the engine must be removed from the machine.
3. Remove bolts (1) from engine oil pan (3) .
4. Remove engine oil pan (3) and gasket (4) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/6312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1. Clean the gasket surfaces of the cylinder block and the engine oil pan thoroughly.
Illustration 3 g01870497
Typical Example
4/6312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 4 g01871553
2. Install a new gasket (4) to the cylinder block. Install engine oil pan (3) .
3. Install bolts (1) . Tighten bolts to a torque of 22 N·m (16 lb ft).
Note: The engine may be equipped with an oil drain plug or the engine may be equipped
with a drain valve.
4. If drain valve (5) and adapter (7) were removed, use the following procedure.
a. Install a new O-ring to the adapter (7) .
b. Install adapter (7) into engine oil pan (3) . Tighten the adapter to a torque of 34 N·m
(25 lb ft).
c. Install a new O-ring to drain valve (5) .
d. Install drain valve (5) into adapter (7) . Tighten the drain valve to a torque of 34 N·m
(25 lb ft).
5. If equipped, install a new O-ring seal on drain plug (2) . Install the drain plug. Tighten the
drain plug to a torque of 34 N·m (25 lb ft). If equipped, close drain valve (5) by turning
handle (6) clockwise. Turn handle (6) until the handle is tight. Do not overtighten the
handle.
6. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.
5/6312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for the correct
engine oil capacity.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 21 23:30:25 UTC+0800 2020
6/6312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312B L EXCAVATOR 9FS
Configuration: 312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04368112
Cylinder Liner - Remove
SMCS - 1216-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1A-1460 Bolt 3
2J-3507 Full Nut 1
5F-7347 Head 1
5H-1504 Hard Washer 1
5P-8245 Washer 3
6V-2183 Screw 1
8H-0684 Ratchet Wrench 1
9U-6234 Puller Plate 1
9U-6281 Leg 3
1D-5119 Nut 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
B. Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Remove".
1/2312B & 312B L Excavators 9FS00001-UP (MACHINE) POWERED BY 3054 Engine...
2020/6/21https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...