The document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by 3003 engines. The procedures describe disconnecting and removing components, cleaning surfaces, installing new seals or gaskets, and reconnecting or reinstalling components while following proper safety and contamination prevention measures.
Caterpillar cat 301.8 mini hydraulic excavator (prefix bfa) service repair ma...fjsjjdkemmde
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.5 mini hydraulic excavator (prefix bfa) service repair ma...fjsekkxszdmmem
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.6 mini hydraulic excavator (prefix bfa) service repair ma...fhsejkdkme
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with new seals and following specified torques. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.5 mini hydraulic excavator (prefix bfa) service repair ma...fjjskekdmem
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.6 mini hydraulic excavator (prefix bfa) service repair ma...ufjsjekfksemm
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.5 mini hydraulic excavator (prefix bfa) service repair ma...dujfjjksekmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The procedures describe disconnecting fuel lines, removing and installing O-rings, and removing and installing the pump while noting shim sizes for proper fuel injection timing. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.6 mini hydraulic excavator (prefix bfa) service repair ma...fjsekkxszdmmem
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The procedures describe disconnecting fuel lines, removing and installing O-rings, and removing and installing the pump while noting shim sizes for proper fuel injection timing. Safety notices are provided regarding containing fluids and preventing contamination.
KOBELCO 140SRLC-3 HYDRAULIC EXCAVATOR Service Repair Manual.pdfjdkksmemmd
This service manual provides instructions for maintenance, repair, and troubleshooting of a Kobelco 140SRLC-3 hydraulic excavator. It begins with general safety information and precautions for working on the machine. The manual is divided into 7 sections covering specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and optional attachments. Technicians are advised to thoroughly prepare and clean the machine before starting any repairs.
Caterpillar cat 301.8 mini hydraulic excavator (prefix bfa) service repair ma...fjsjjdkemmde
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.5 mini hydraulic excavator (prefix bfa) service repair ma...fjsekkxszdmmem
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.6 mini hydraulic excavator (prefix bfa) service repair ma...fhsejkdkme
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with new seals and following specified torques. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.5 mini hydraulic excavator (prefix bfa) service repair ma...fjjskekdmem
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.6 mini hydraulic excavator (prefix bfa) service repair ma...ufjsjekfksemm
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, fuel injection pump, and exhaust manifold on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators powered by a 3003 engine. The procedures describe disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components along with torque specifications for fasteners. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.5 mini hydraulic excavator (prefix bfa) service repair ma...dujfjjksekmmd
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The procedures describe disconnecting fuel lines, removing and installing O-rings, and removing and installing the pump while noting shim sizes for proper fuel injection timing. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar cat 301.6 mini hydraulic excavator (prefix bfa) service repair ma...fjsekkxszdmmem
This document provides instructions for removing and installing fuel injection lines, the fuel shutoff solenoid, and the fuel injection pump on Caterpillar 301.5, 301.6, and 301.8 mini hydraulic excavators. The procedures describe disconnecting fuel lines, removing and installing O-rings, and removing and installing the pump while noting shim sizes for proper fuel injection timing. Safety notices are provided regarding containing fluids and preventing contamination.
KOBELCO 140SRLC-3 HYDRAULIC EXCAVATOR Service Repair Manual.pdfjdkksmemmd
This service manual provides instructions for maintenance, repair, and troubleshooting of a Kobelco 140SRLC-3 hydraulic excavator. It begins with general safety information and precautions for working on the machine. The manual is divided into 7 sections covering specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and optional attachments. Technicians are advised to thoroughly prepare and clean the machine before starting any repairs.
KOBELCO 70SR-2 Acera Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
The document is a service manual that provides instructions for disassembling a pilot valve used in a Kobelco Construction Machinery hydraulic excavator model 70SR-2 Acera. It includes diagrams of the valve components and specifies tightening torques. The disassembly instructions describe removing external components like boots and nuts, then internal parts like springs, spools and seals while taking safety precautions for any stored energy in the valve springs.
KOBELCO 17SR-Tier 4 Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
This document provides guidelines and safety precautions for repairing hydraulic excavators. It covers preparing for disassembly, safety during disassembly and assembly, working with hydraulic equipment and electrical components, handling hydraulic parts, welding repairs, and an international unit conversion system. Technicians are instructed to thoroughly read manuals, use proper tools, relieve pressures, and take caution with hot or heavy components. Protective equipment is recommended.
Komatsu WA270PT-3 Wheel Loader Service Repair Manual SN WA270H30051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which requires draining fluids, removing wiring, hoses, and other attachments to the engine before lifting it out.
3) Additional sections provide instructions for removing and installing other components like the radiator, fuel tank, and counterweight. Precise steps are outlined, safety precautions noted, and proper torque specifications and fluid fill amounts are provided.
Komatsu WA270-3 Wheel Loader Service Repair Manual SN WA270H20051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which has many steps including draining fluids, removing wiring, hoses, and mounting components.
3) Procedures for removing and installing other major components like the radiator, fuel tank, and counterweight. Detailed safety precautions and instructions are provided.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkksmemmd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix PJW) Service Repair Manual...jdkksmemmd
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housed within sprocket and motor housings. Bearings must be properly seated and preloaded during assembly. Seals, shims, and other components are also installed according to detailed steps. Proper cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...jdkksmemmd
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and installation of identification marks are emphasized to ensure correct reassembly of components. Tools required are also listed.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, thrust washers, retaining rings, and bearings. Instructions are provided to remove the ring gear housing, carrier gear, piston, seals, discs, and hub. Precautions and notes are included to aid the technician.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, bearing cones, shims, seals, sprockets, gears and carriers. Proper bearing preload is critical and is achieved through measuring clearances and determining the correct shim thickness. Lifting devices and clean lubricant are used during assembly to install heavy components like the sprocket housing and carrier assemblies.
This document provides assembly instructions for a hydraulic pump in 3 steps:
1. Install various internal components of the pump like bearings, pistons, seals according to 61 illustrated steps.
2. Attach the pump control unit with additional internal components like springs, valves, fittings in 59 illustrated steps.
3. Connect the assembled hydraulic pump and control unit together and install it on the excavator by securing with bolts.
This document provides disassembly instructions for the final drive carriers, hubs, and brakes on the front and rear axles of an M322C wheeled excavator. It lists 41 steps to fully disassemble the components, including removing retaining rings, gears, bearings, seals, and other parts using various specialized tools. Detailed illustrations accompany each step to show how to remove the individual pieces and subassemblies. Safety notices are also provided regarding releasing pressure and containing fluids before disassembly.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...jdkksmemmd
The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, and housing components. Precision is required to reinstall the springs, pistons, and other small parts correctly. The final steps are to install the motor housing cover and tighten the bolts to the specified torque.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
KOBELCO 70SR-2 Acera Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
The document is a service manual that provides instructions for disassembling a pilot valve used in a Kobelco Construction Machinery hydraulic excavator model 70SR-2 Acera. It includes diagrams of the valve components and specifies tightening torques. The disassembly instructions describe removing external components like boots and nuts, then internal parts like springs, spools and seals while taking safety precautions for any stored energy in the valve springs.
KOBELCO 17SR-Tier 4 Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
This document provides guidelines and safety precautions for repairing hydraulic excavators. It covers preparing for disassembly, safety during disassembly and assembly, working with hydraulic equipment and electrical components, handling hydraulic parts, welding repairs, and an international unit conversion system. Technicians are instructed to thoroughly read manuals, use proper tools, relieve pressures, and take caution with hot or heavy components. Protective equipment is recommended.
Komatsu WA270PT-3 Wheel Loader Service Repair Manual SN WA270H30051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which requires draining fluids, removing wiring, hoses, and other attachments to the engine before lifting it out.
3) Additional sections provide instructions for removing and installing other components like the radiator, fuel tank, and counterweight. Precise steps are outlined, safety precautions noted, and proper torque specifications and fluid fill amounts are provided.
Komatsu WA270-3 Wheel Loader Service Repair Manual SN WA270H20051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which has many steps including draining fluids, removing wiring, hoses, and mounting components.
3) Procedures for removing and installing other major components like the radiator, fuel tank, and counterweight. Detailed safety precautions and instructions are provided.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkksmemmd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix PJW) Service Repair Manual...jdkksmemmd
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housed within sprocket and motor housings. Bearings must be properly seated and preloaded during assembly. Seals, shims, and other components are also installed according to detailed steps. Proper cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...jdkksmemmd
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and installation of identification marks are emphasized to ensure correct reassembly of components. Tools required are also listed.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, thrust washers, retaining rings, and bearings. Instructions are provided to remove the ring gear housing, carrier gear, piston, seals, discs, and hub. Precautions and notes are included to aid the technician.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, bearing cones, shims, seals, sprockets, gears and carriers. Proper bearing preload is critical and is achieved through measuring clearances and determining the correct shim thickness. Lifting devices and clean lubricant are used during assembly to install heavy components like the sprocket housing and carrier assemblies.
This document provides assembly instructions for a hydraulic pump in 3 steps:
1. Install various internal components of the pump like bearings, pistons, seals according to 61 illustrated steps.
2. Attach the pump control unit with additional internal components like springs, valves, fittings in 59 illustrated steps.
3. Connect the assembled hydraulic pump and control unit together and install it on the excavator by securing with bolts.
This document provides disassembly instructions for the final drive carriers, hubs, and brakes on the front and rear axles of an M322C wheeled excavator. It lists 41 steps to fully disassemble the components, including removing retaining rings, gears, bearings, seals, and other parts using various specialized tools. Detailed illustrations accompany each step to show how to remove the individual pieces and subassemblies. Safety notices are also provided regarding releasing pressure and containing fluids before disassembly.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...jdkksmemmd
The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, and housing components. Precision is required to reinstall the springs, pistons, and other small parts correctly. The final steps are to install the motor housing cover and tighten the bolts to the specified torque.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01112109
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00587462
1. Disconnect fuel injection lines (1) from fuel injection nozzles (2) .
NOTICE
Do not let the tops of fuel nozzles turn when the fuel line nuts are
loosened or tightened.
The nozzles will be damaged if the top of the nozzle turns in the body.
The engine will be damaged if a defective fuel injection nozzle is used
because the shape of fuel (spray pattern) that comes out of the nozzles
will not be correct.
2. Disconnect fuel injection lines (1) from fuel injection pump (3). Cap all openings or plug all
openings immediately.
3. Remove fuel injection lines (1) from the engine as a unit.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00587462
1. Install fuel injection lines (1) on the engine as a unit.
NOTICE
Do not let the tops of fuel nozzles turn when the fuel line nuts are
loosened or tightened.
The nozzles will be damaged if the top of the nozzle turns in the body.
The engine will be damaged if a defective fuel injection nozzle is used
because the shape of fuel (spray pattern) that comes out of the nozzles
will not be correct.
2. Connect fuel injection lines (1) to fuel injection pump (3). Tighten the fuel injection line
nuts to the following torque:
3003 Engine ... 22 N·m (16 lb ft)
3013, 3014, and 3024 Engines ... 20 N·m (15 lb ft)
3. Connect fuel injection lines (1) to fuel injection nozzles (2). Tighten the fuel injection line
nuts to the following torque:
3003 Engine ... 22 N·m (16 lb ft)
3013, 3014, and 3024 Engines ... 20 N·m (15 lb ft)
4. Prime the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime" for more
information.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:09:49 UTC+0800 2020
3/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01428959
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Disconnect all electrical connections to the fuel shutoff solenoid before proceeding.
Mark all connections for later installation.
1/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g00592462
1. Remove fuel shutoff solenoid (1) from the governor by rotating fuel shutoff solenoid (1) in
a counterclockwise direction.
2. Remove the O-ring seal from fuel shutoff solenoid (1). Inspect the O-ring seal for wear or
for damage. If the O-ring seal is worn or damaged, use a new part for replacement.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00592462
1. Install the O-ring seal onto fuel shutoff solenoid (1) .
2/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 2. Install fuel shutoff solenoid (1) in the governor by rotating fuel shutoff solenoid (1) in a
clockwise direction. Tighten fuel shutoff solenoid (1) to a torque of 17 N·m (12 lb ft).
Note: Reconnect all electrical connections to the fuel shutoff solenoid before you operate
the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:10:46 UTC+0800 2020
3/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i04583132
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. If necessary, remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel
Shutoff Solenoid - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00825132
Illustration 2 g00825137
1. Remove bolts (4) and nuts (2) that fasten the fuel injection pump to the cylinder block.
2. Carefully raise fuel injection pump (1) from the cylinder block and remove clip (7) that
connects link (6) to fuel rack control (5) .
2/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 3. Remove fuel injection pump (1) from the cylinder block.
Note: Record the thickness of each shim and the number of shims for reassembly. The fuel
injection timing is determined by the shim pack thickness that is between the fuel injection
pump and the mounting face on the cylinder block. For more information on the fuel
injection pump, refer to Specifications, "Fuel Injection Pump".
4. Remove shims (3) from the mounting plate.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:11:43 UTC+0800 2020
3/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01591134
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g00825132
1. Position the correct number of shims (3) on the mounting face of the cylinder block. Refer
to Specifications, "Fuel Injection Pump".
Illustration 2 g00825137
2. Position fuel injection pump (1) close to the mounting face of the cylinder block, and
connect link (6) and fuel rack control (5) with clip (7) .
3. Put fuel injection pump (1) in position on the mounting face of the cylinder block.
4. Install bolts (4) and nuts (2) that fasten the fuel injection pump to the cylinder block.
Tighten bolts (4) and nuts (2) to the following torque.
2/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 3003 Engine ... 6 N·m (4 lb ft)
3013, 3014, and 3024 Engines ... 15 N·m (11 lb ft)
3024C Engine ... 15 N·m (11 lb ft)
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
b. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:12:39 UTC+0800 2020
3/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i01893805
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g00825291
Typical example
1. Remove exhaust manifold nuts (5) and bolts (6) .
2. Remove exhaust manifold (4) from the cylinder head (1) .
3. Remove gasket (3) from the cylinder head.
4. Remove any remaining gasket material and carbon from the cylinder head and the exhaust
manifold. Be careful not to damage the mating surface on the cylinder head for the exhaust
manifold.
5. Remove studs (2) for exhaust manifold (4) from cylinder head (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00825291
Typical example
2/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 1. If studs (2) were removed during disassembly, install attaching studs (2) to cylinder head
(1) .
2. Put a new exhaust manifold gasket (3) in position on cylinder head (1) .
Note: Do not use any sealant on the exhaust manifold gasket.
3. Put exhaust manifold (4) in position on cylinder head (1) .
4. Install exhaust manifold nuts (5) and bolts (6) .
For 3013C Engines and 3024C Engines, tighten nuts (5) and bolts (6) to a torque of 25 N·m
(18 lb ft).
For 3011C Engines, tighten nuts (5) and bolts (6) to a torque of 10 N·m (89 lb in).
Note: Tighten the two inner bolts first on three cylinder engines. Tighten the four inner
bolts first on four cylinder engines. Then tighten the two outer bolts and the two nuts.
Ensure that the bolts with different lengths are installed in the correct holes.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:13:36 UTC+0800 2020
3/3
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i02399171
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Start By:
A. Remove the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Before you begin the removal of the valve springs, refer to Specifications, "Cylinder Head
Valves" and Testing and Adjusting, "Cylinder Head - Inspect" for appropriate information on the
valve springs.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
1/4
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 1. Ensure that the piston is at the top center position.
Illustration 1 g00825744
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. Use Tooling (A) to compress valve springs (1) . Remove valve keepers (2) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
3. Release the pressure on Tooling (A) . Remove valve spring retainer (3) and valve springs
(1) from the cylinder head.
2/4
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. NOTICE
Do not turn the crankshaft while the valve springs are removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00825744
3/4
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Place new valve springs (1) into position on the cylinder head.
Note: Ensure that the closed damper coils are toward the cylinder head if double valve
springs are used.
2. Install valve spring retainer (3) .
3. Use Tooling (A) to compress valve springs (1) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
4. Install valve keepers (2) in order to lock the valve springs in position.
5. Release the pressure slowly on Tooling (A) . Remove Tooling (A) . Strike the top of the
valves with a soft faced hammer in order to ensure that the valve keepers are properly
installed.
End By: Install the rocker shaft. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 23:14:33 UTC+0800 2020
4/4
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8 MINI HYD EXCAVATOR BFA
Configuration: 301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERED BY 3003 Engine
Disassembly and Assembly
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines
Media Number -SENR5027-05 Publication Date -01/05/2005 Date Updated -16/05/2005
i02015360
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom face of the cylinder head. Use a dial indicator to check the depth of the
valves below the face of the cylinder head before the valve springs are removed. Refer to
the Specifications, "Cylinder Head Valves" for the correct dimensions.
2. Place an index mark on the heads of the inlet valves and the exhaust valves for installation
purposes.
1/6
301.5 301.6 301.8 Mini Hydraulic Excavator BFA00001-UP (MACHINE) POWERE...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...