Caterpillar cat 287 d multi terrain loader (prefix stk) service repair manual (stk00001 and up)

Service Repair Manual
Models
287D MULTI TERRAIN LOADER

Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 287D MULTI TERRAIN LOADER STK
Configuration: 287D Multi Terrain Loader STK00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D,
297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and
272D XHP Skid Steer Loaders Power Train
Media Number -UENR3730-09 Publication Date -01/05/2015 Date Updated -13/08/2018
i06659865
Piston Pump (Hydrostatic) - Disassemble
SMCS - 5070-015-H7
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 9S-9152 Puller Attachment As. 1
C
0S-1527 Bolt 1
2J-3506 Full Nut 1
8T-4122 Hard Washer 2
D 1P-1859 Retaining Ring Pliers 1
Start By:
a. Remove the pump. Refer to Disassembly and Assembly, "Piston Pump (Hydrostatic) -
Remove".
1/10287D Multi Terrain Loader STK00001-UP (MACHINE) POWERED BY C3.3B Engi...
2019/10/19https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01325524
1. Remove bolts (1) and valve (2).
2. Remove nut (3), the O-ring seal, coil (4), bolts (5), and cartridge (6).
3. Remove screen (6A).

4. Remove gasket (7) and control arm (8).
5. Remove bolts (9) and valve (10).
6. Repeat Steps 2 through Steps 4 for valve (10).
7. Remove nut (13), coil (12), and cartridge (14).
8. Remove valve (11).

9. Remove plugs (14A), O-ring seal (14E), O-ring seal (14C), backup ring (14D) and
crossover relief valves (14B), from the head.
10. Remove O-ring seal (15), backup rings (16), and O-ring seals (17).

11. Remove O-ring seal (18), backup ring (19), and O-ring seal (20).
12. Remove bolts (21) and housing (22).
13. Remove bolts (25), retainer (24), and set screw (23).
14. Repeat Step 13 for the opposite side.

15. Remove O-ring seal (26).
16. Remove piston assembly (27) and swashplate (28).
17. Remove seals (29) and block (30).

18. Remove bearings (31) from swashplate (28).
19. Remove shaft (32).
20. Use Tooling (A), Tooling (B), and a suitable press to remove bearing (33) from the shaft.

21. Remove barrel assembly (34).
22. Remove port plate (36) and gasket (35).
23. Remove coupling (37).
24. Remove head (38).
25. Repeat Step 22 for head (38).

26. Remove bearings (39).
27. Remove barrel assembly (40).
28. Repeat Step 13 through Step 19.
29. Remove retaining ring (47).
30. Remove plate (46).

31. Remove O-ring seal (45).
32. Remove seal (44) and shaft assembly (41).
33. Use Tooling (D) to remove retaining ring (43).
34. Use Tooling (B) and a suitable press to remove bearing (42).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 19 09:57:13 UTC+0800 2019
10/10287D Multi Terrain Loader STK00001-UP (MACHINE) POWERED BY C3.3B En...

Shutdown SIS
Previous Screen
Product: MULTI TERRAIN LOADER
Model: 287D MULTI TERRAIN LOADER STK
Configuration: 287D Multi Terrain Loader STK00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D,
297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and
272D XHP Skid Steer Loaders Power Train
Media Number -UENR3730-09 Publication Date -01/05/2015 Date Updated -13/08/2018
i06660138
Piston Pump (Hydrostatic) - Assemble
SMCS - 5070-016-H7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
D 1P-1859 Retaining Ring Pliers 1
E 9S-3263 Thread Lock Compound 1

1. Raise the temperature of bearing (42).
2. Install bearing (42).
3. Use Tooling (D) to install retaining ring (43).
4. Install shaft assembly (40) and seal (44).
5. Install O-ring seal (45).
6. Install plate (46).
7. Install retaining ring (47).

8. Raise the temperature of bearing (33).
9. Install bearing (33) onto shaft (32).
10. Install shaft (32).
11. Install bearings (31) onto swashplate (28).

12. Install seals (29) and block (30).
13. Install piston assembly (27) and swashplate (28).
14. Install O-ring seal (26).

15. Install set screw (23). Apply slight pressure to the piston assembly.
16. Repeat Step 15 for the opposite side.
17. Use a suitable measuring device to center the swashplate. Measure the distance that is from
the machined face of the housing to both sides of the swashplate. Adjust setscrews (23) to
achieve the same distance to the swashplate.
18. Install retainer (24), and bolts (25).
19. Install barrel assembly (40).

20. Install bearings (39).
21. Install port plate (36) and gasket (35).
22. Install head (38).
23. Install coupling (37).
24. Repeat Steps16 through Steps 23 for barrel assembly (34).
25. Install barrel assembly (34).
26. Install housing (22) and bolts (21). Tighten bolts (21) to a torque of 110 ± 10 N·m
(81 ± 7 lb ft).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

27. Install crossover relief valves (14B), backup ring (14D), O-ring seal (14C), O-ring seal
(14E) and plugs (14A) into the head.
28. Install O-ring seal (20), backup ring (19), and O-ring seal (18).

29. Install O-ring seals (17), backup rings (16), and O-ring seal (15).
30. Install valve (11). Tighten valve (11) to a torque of 44 ± 3 N·m (32 ± 2 lb ft).
31. Install cartridge (14), coil (12), and nut (13). Tighten nut (13) to a torque of 80 ± 10 N·m
(59 ± 7 lb ft).
32. Install the cross over relief valves and the plugs into the head. Tighten plugs (21) to a torque
of 110 ± 10 N·m (81 ± 7 lb ft).

33. Install screen (6A).
34. Install cartridge (6), bolts (5), coil (4), the O-ring seal, and nut (3). Tighten bolts (5) to a
torque of 5.5 ± 0.1 N·m (49 ± 0.9 lb in).
35. Install control arm (8) and gasket (7).
36. Apply Tooling (E) to control arm (8).

37. Install valve (10) and bolts (9). Tighten bolts (9) to a torque of 13 ± 1 N·m (115 ± 9 lb in).
38. Repeat Steps 34 through Steps 35 for valve (2).
39. Install bolts (1) and valve (2). Tighten bolts (1) to a torque of 13 ± 1 N·m (115 ± 9 lb in).
40. Bench test the pump before installation into the machine.
End By:
a. Install the pump. Refer to Disassembly and Assembly, "Piston Pump (Hydrostatic) -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 19 09:58:08 UTC+0800 2019
10/10287D Multi Terrain Loader STK00001-UP (MACHINE) POWERED BY C3.3B En...

Caterpillar cat 287 d multi terrain loader (prefix stk) service repair manual (stk00001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 287 d multi terrain loader (prefix stk) service repair manual (stk00001 and up)

Similar to Caterpillar cat 287 d multi terrain loader (prefix stk) service repair manual (stk00001 and up) (15)

More from fhshefjjskefkem

More from fhshefjjskefkem (20)

Recently uploaded

Recently uploaded (19)

Caterpillar cat 287 d multi terrain loader (prefix stk) service repair manual (stk00001 and up)