This document provides instructions for removing and installing components on a Caterpillar 3034 engine, including:
- Removing the fuel injection pump by disconnecting linkages, removing mounting bolts and shims, and ensuring openings are covered.
- Installing the fuel injection pump by cleaning surfaces, positioning shims, installing mounting bolts and linkages.
- Removing the turbocharger by disconnecting hoses and lines, removing mounting nuts, and plugging openings.
- Installing the turbocharger by positioning the gasket and turbocharger, installing mounting nuts, and connecting hoses and lines.
- Removing the exhaust manifold by removing mounting bolts and gasket.
- Installing
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01354467
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Start By:
A. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
B. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/5236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00599562
1. Remove fuel lines (2) from the engine. Immediately cap all openings or plug all openings in
order to prevent contamination of the fuel system.
2. Remove bolts (1) and cover (3) from the engine.
Illustration 2 g00720261
3. Disconnect spring (5) from the groove in pin (4) .
2/5236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00720270
Note: Spring (6) may fall into the engine if the spring comes loose from pin (4) .
4. Disconnect spring (6) from the groove in pin (4) .
Illustration 4 g00720275
5. Disconnect governor control linkage (9) from pin (4) .
Illustration 5 g00720284
3/5236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 6. Remove bolts (10) and nuts (11) that secure the fuel injection pump to the engine.
Illustration 6 g00720291
7. Remove fuel injection pump (12) from the engine.
Note: Record the thickness of each shim and the number of shims for reassembly. The fuel
injection timing is determined by the shim pack thickness that is between the fuel injection
pump and the mounting face on the cylinder block. For more information on the fuel
injection pump, refer to the Specifications Module, "Fuel Injection Pump" topic.
8. Remove shims (14) from fuel injection pump (12) .
9. Inspect dowels (15) for damage. If the dowels are damaged, use new dowels for
replacement.
10. Inspect pin (4) for wear or damage. If pin (4) is worn or damaged, use a new pin for
replacement.
11. Cover the opening in the fuel injection pump housing for fuel injection pump (12) in order
to prevent debris from falling into the engine.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Wed Nov 20 23:55:01 UTC+0800 2019
4/5236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01354577
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00720291
1. Make sure that the mating surface of the fuel injection pump housing and fuel injection
pump (12) are clean and free from debris.
2. Position the correct number of shims (14) on the fuel injection pump housing. Refer to the
Specifications Module, "Fuel Injection Pump" topic for more information.
3. Ensure that pin (4) is aligned with the notch in shims (14) and the notch in the cylinder
block. Align dowels (15) with fuel injection pump (12). Put fuel injection pump (12) in
position on the engine.
2/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g00720284
4. Install nuts (11) and bolts (10) that secure the fuel injection pump to the engine. Tighten
nuts (11) and bolts (10) evenly to a torque of 22 N�m (16 lb ft).
Illustration 3 g00720275
5. Install governor control linkage (9) onto pin (4) .
Illustration 4 g00720270
6. Install spring (6) in the groove in pin (4) .
3/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 5 g00720261
7. Install spring (5) into the groove in pin (4) .
Illustration 6 g00599562
8. Clean the mating surface of plate (3) and the cylinder block.
9. Put plate (3) in position on the engine and install bolts (1).
10. Remove the caps and the plugs from fuel lines (2) and install the fuel lines on the engine.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
b. Install the air inlet manifold. Refer to Disassembly and Assembly, " Inlet Manifold -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 20 23:55:57 UTC+0800 2019
4/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01365306
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00596955
1. Loosen hose clamps (1) and (3). Slide the hoses away from turbocharger (2) .
Illustration 2 g00597025
2. Remove oil line (4) from turbocharger (2). Immediately cap all openings or plug all
openings in order to prevent contamination.
3. Loosen hose clamp (5) for the oil drain line.
4. Remove three nuts (6) that fasten turbocharger (2) to the exhaust manifold.
2/3236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00597180
5. Remove turbocharger (2) and gasket (7) from the engine. Plug the hose for the oil drain line
in order to prevent contamination. Inspect the condition of gasket (7). If gasket (7) is worn
or damaged, replace the gasket.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 20 23:56:53 UTC+0800 2019
3/3236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01130095
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00597180
1. Put gasket (7) and turbocharger (2) in position on the exhaust manifold.
1/2236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g00597025
2. Install three nuts (6) that fasten turbocharger (2) to the exhaust manifold. Tighten the nuts to
a torque of 22 N�m (16 lb ft).
3. Tighten hose clamp (5) for the oil drain line.
4. Connect oil line (4) to turbocharger (2) .
Illustration 3 g00596955
5. Slide the hoses toward turbocharger (2) and tighten hose clamps (3) and (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 20 23:57:48 UTC+0800 2019
2/2236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01099748
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00578523
1. Remove eight bolts (1) from exhaust manifold (2) .
1/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 2 g00578529
2. Remove exhaust manifold (2) and gasket (3) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Make sure that the cylinder head and the exhaust manifold are clean and free of carbon and
gasket material.
2/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00578574
2. Install two guide bolts (4) into two of the bolt holes for the exhaust manifold bolts. The
guide bolts are used to keep exhaust manifold gasket (3) and exhaust manifold (2) in
position on the cylinder head during installation.
3. Put a new exhaust manifold gasket (3) in position on the engine. It is not necessary to use a
sealer on the exhaust manifold gasket.
Illustration 4 g00578523
4. Put exhaust manifold (2) in position on the engine.
5. Install six of the eight bolts (1) and remove the two guide bolts. Install the remaining two
bolts (1) .
6. Tighten eight bolts (1) in an outward pattern. Begin with the center of the exhaust manifold.
Tighten bolts (1) to a torque of 18 N�m (13 lb ft).
Wed Nov 20 23:58:44 UTC+0800 2019
3/4236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 248 SKID STEER LOADER 6LZ
Configuration: 236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01333774
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00580923
1/2236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Remove eight bolts (1) from air inlet manifold (2) .
Illustration 2 g00580932
2. Remove air inlet manifold (2) and gasket (3) from the engine. Check the condition of gasket
(3). If gasket (3) is worn or damaged, use a new part for replacement.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 20 23:59:40 UTC+0800 2019
2/2236, 246, 248 Skid Steer Loader 6LZ00001-00999 (MACHINE) POWERED BY 3034...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...