This document provides instructions for removing and installing components of the fuel system for a Caterpillar 229 Excavator, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
It emphasizes keeping parts clean and containing fluids during maintenance. Removal and installation procedures include lists of required tools and step-by-step instructions with illustrations.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...fjskemmd4r
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing bolts, and installed by reconnecting lines and bolts after checking gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing bolts, and installed by reversing removal steps and turning the fuel supply valve back on.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...jfkksemmdmd
The document provides instructions for disassembling and assembling components of the fuel system for a 235B Excavator. It describes how to remove and install parts like the fuel priming pump, fuel filter base, and fuel transfer pump. The procedures include removing hoses, bolts, seals, and internal parts in a specific sequence. New seals and gaskets are recommended if worn. Fluids must be contained properly and all parts kept clean to prevent contamination.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 235B Excavator including:
1) The fuel priming pump, which is removed by taking off bolts and disconnecting tubes, and installed by reversing the removal steps.
2) The fuel filter base, which is removed by disconnecting lines and removing bolts, and installed by reconnecting lines and bolts.
3) The fuel transfer pump, which is removed by disconnecting tubes and removing bolts, and provides disassembly and assembly instructions involving several internal parts.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing securing bolts and installing by reversing removal and replacing any worn gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing securing bolts and the O-ring seal, and installed by reversing the removal steps.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...ufjskekdjdmw2
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts, and installed by reversing removal and checking for damaged gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing mounting bolts, and installed by reversing removal steps.
The document also provides disassembly and assembly instructions for the fuel transfer pump involving removing and replacing various seals and internal components.
The document provides instructions for disassembling and assembling components of the fuel system for a 235B Excavator. It describes how to remove and install parts like the fuel priming pump, fuel filter base, and fuel transfer pump. The procedures include removing hoses, bolts, seals, and internal parts in a specific sequence. New seals and gaskets are recommended whenever parts are removed. Fluids must be contained properly and all parts kept clean to prevent contamination.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...fujsked9dikdkd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts, and installed by reversing removal and checking for damaged gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing mounting bolts, and installed by reversing removal steps.
The document also provides disassembly and assembly instructions for the fuel transfer pump involving removing and replacing various seals and internal components.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...gen78guozun
The document provides instructions for removing and installing several fuel system components on a Caterpillar 235B excavator including:
1) The fuel priming pump, which must be removed by taking off bolts and disconnecting tubes before being reinstalled.
2) The fuel filter base, which is removed by disconnecting fuel lines and removing bolts, and is reinstalled by reversing the process.
3) The fuel transfer pump, which is removed by disconnecting tubes and removing bolts, and is reinstalled by reversing the process. Detailed disassembly and assembly instructions are also provided for the fuel transfer pump.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...fjskemmd4r
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing bolts, and installed by reconnecting lines and bolts after checking gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing bolts, and installed by reversing removal steps and turning the fuel supply valve back on.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...jfkksemmdmd
The document provides instructions for disassembling and assembling components of the fuel system for a 235B Excavator. It describes how to remove and install parts like the fuel priming pump, fuel filter base, and fuel transfer pump. The procedures include removing hoses, bolts, seals, and internal parts in a specific sequence. New seals and gaskets are recommended if worn. Fluids must be contained properly and all parts kept clean to prevent contamination.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 235B Excavator including:
1) The fuel priming pump, which is removed by taking off bolts and disconnecting tubes, and installed by reversing the removal steps.
2) The fuel filter base, which is removed by disconnecting lines and removing bolts, and installed by reconnecting lines and bolts.
3) The fuel transfer pump, which is removed by disconnecting tubes and removing bolts, and provides disassembly and assembly instructions involving several internal parts.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing securing bolts and installing by reversing removal and replacing any worn gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing securing bolts and the O-ring seal, and installed by reversing the removal steps.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...ufjskekdjdmw2
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts, and installed by reversing removal and checking for damaged gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing mounting bolts, and installed by reversing removal steps.
The document also provides disassembly and assembly instructions for the fuel transfer pump involving removing and replacing various seals and internal components.
The document provides instructions for disassembling and assembling components of the fuel system for a 235B Excavator. It describes how to remove and install parts like the fuel priming pump, fuel filter base, and fuel transfer pump. The procedures include removing hoses, bolts, seals, and internal parts in a specific sequence. New seals and gaskets are recommended whenever parts are removed. Fluids must be contained properly and all parts kept clean to prevent contamination.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...fujsked9dikdkd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 235B excavator including:
- The fuel priming pump, which is removed by taking off securing bolts and disconnecting tubes, and installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts, and installed by reversing removal and checking for damaged gaskets.
- The fuel transfer pump, which is removed by disconnecting tubes and removing mounting bolts, and installed by reversing removal steps.
The document also provides disassembly and assembly instructions for the fuel transfer pump involving removing and replacing various seals and internal components.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...gen78guozun
The document provides instructions for removing and installing several fuel system components on a Caterpillar 235B excavator including:
1) The fuel priming pump, which must be removed by taking off bolts and disconnecting tubes before being reinstalled.
2) The fuel filter base, which is removed by disconnecting fuel lines and removing bolts, and is reinstalled by reversing the process.
3) The fuel transfer pump, which is removed by disconnecting tubes and removing bolts, and is reinstalled by reversing the process. Detailed disassembly and assembly instructions are also provided for the fuel transfer pump.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 229 Excavator with a 3304 engine. It includes step-by-step procedures for removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and disassembling and assembling the fuel transfer pump. Safety notices are provided to keep parts clean and contain fluids during the repair work.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 229 Excavator with a 3304 engine. It includes step-by-step procedures for removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and disassembling and assembling the fuel transfer pump. Safety notices are provided to keep parts clean and contain fluids during the repair work.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 229 Excavator with a 3304 engine. It includes step-by-step procedures for removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and disassembling and assembling the fuel transfer pump. Safety notices are provided to keep parts clean and contain fluids during the repair work.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...xiapokang564341
This document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, disassembling the fuel transfer pump, and assembling the fuel transfer pump on a 235B EXCAVATOR model powered by a 3306 engine. The procedures provide detailed steps and illustrations for each maintenance task. Safety and contamination prevention notices are also provided.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...hvy7sbkw8e
This document provides instructions for disassembling and assembling components of the fuel system for a Caterpillar 3306 engine. It describes how to remove and install the fuel priming pump, fuel filter base, and fuel transfer pump. The procedures include removing bolts and hoses, checking gaskets, and installing parts in the reverse order of removal. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...wenxian17880
This document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, disassembling the fuel transfer pump, and assembling the fuel transfer pump on a 235B EXCAVATOR model powered by a 3306 engine. The procedures provide detailed steps and illustrations for each maintenance task. Safety and contamination prevention notices are included at the beginning of each section.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...fujsjefkksekmme
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal procedure involves using a strap wrench to remove the filter, disconnecting a fuel line, and removing two bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump requires turning off the fuel supply, removing two tubes and two bolts, and removing the pump.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...ujjfdjkjskkmdm
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal procedure involves using a strap wrench to remove the filter, disconnecting a fuel line, and removing two bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump requires turning off the fuel supply, removing two tubes and two bolts, and removing the pump.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...fujsfskekem
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...uudfjjjskkemmd
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and disassembling components of the fuel transfer pump for a 225 EXCAVATOR powered by a 3304 engine, including:
- Removing the fuel transfer pump by disconnecting tubes and removing bolts.
- Disassembling the pump housing by removing the cover, spring, seals, valve assemblies, piston, sleeve, seals and bolts.
- Instructions specify cleaning parts and containing fluids during maintenance.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...ujjfdjkjskkmdm
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The removal procedure involves turning off the fuel supply, disconnecting tubes, and removing bolts to access the pump. The disassembly process describes removing springs, seals, sleeves, pistons, and other components from the pump housing. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...uudfjjjskkemmd
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The removal procedure involves turning off the fuel supply, disconnecting tubes, and removing bolts to access the pump. The disassembly process describes removing springs, seals, sleeves, pistons, and other components from the pump housing. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...fujsjefkksekmme
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The procedures describe draining fuel, removing mounting bolts and hoses, installing replacement seals and gaskets, and reattaching components. Disassembly and assembly of the fuel transfer pump is also outlined.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...fujsfskekem
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The procedures describe draining fuel, removing mounting bolts and hoses, installing new seals and gaskets if needed, and reattaching components in the reverse order of removal. Disassembly and assembly of the fuel transfer pump internals is also outlined.
This document provides instructions for removing and disassembling the fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the pump by disconnecting fuel lines and removing bolts. It then details disassembling the pump by removing springs, seals, valves, sleeves, pistons and other components. Precautions are provided to keep parts clean and contain fluids during maintenance.
The documents provide instructions for servicing components of a Caterpillar 3306 engine used in a 235 excavator, including:
1) Procedures for removing and installing the automatic timing advance, which involves aligning gears, removing bolts and plates, and using support tools.
2) Disassembling the automatic timing advance unit by removing screws, plates, springs, weights and seals.
3) Reassembling the automatic timing advance unit by installing seals, gears, slides, weights, springs and plates.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00455-00...fujskekdjdmd
The document provides instructions for servicing components of a 235 excavator, including removing, disassembling, and reassembling the boom speed control valve, track brake valve, boom vent valve, swing combiner and relief valve, and pump selector valve. Removal instructions involve disconnecting lines and removing mounting bolts. Disassembly involves removing internal components like springs, stems, and plugs. Reassembly follows the reverse order and ensures proper installation of seals and adjustment of clearance sizes.
More Related Content
Similar to Caterpillar Cat 229 EXCAVATOR (Prefix 1AG) Service Repair Manual (1AG00001 and up).pdf
This document provides instructions for removing and installing various fuel system components on a Caterpillar 229 Excavator with a 3304 engine. It includes step-by-step procedures for removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and disassembling and assembling the fuel transfer pump. Safety notices are provided to keep parts clean and contain fluids during the repair work.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 229 Excavator with a 3304 engine. It includes step-by-step procedures for removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and disassembling and assembling the fuel transfer pump. Safety notices are provided to keep parts clean and contain fluids during the repair work.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 229 Excavator with a 3304 engine. It includes step-by-step procedures for removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and disassembling and assembling the fuel transfer pump. Safety notices are provided to keep parts clean and contain fluids during the repair work.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...xiapokang564341
This document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, disassembling the fuel transfer pump, and assembling the fuel transfer pump on a 235B EXCAVATOR model powered by a 3306 engine. The procedures provide detailed steps and illustrations for each maintenance task. Safety and contamination prevention notices are also provided.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...hvy7sbkw8e
This document provides instructions for disassembling and assembling components of the fuel system for a Caterpillar 3306 engine. It describes how to remove and install the fuel priming pump, fuel filter base, and fuel transfer pump. The procedures include removing bolts and hoses, checking gaskets, and installing parts in the reverse order of removal. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar Cat 235B EXCAVATOR (Prefix 9PC) Service Repair Manual (9PC00001-...wenxian17880
This document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, disassembling the fuel transfer pump, and assembling the fuel transfer pump on a 235B EXCAVATOR model powered by a 3306 engine. The procedures provide detailed steps and illustrations for each maintenance task. Safety and contamination prevention notices are included at the beginning of each section.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...fujsjefkksekmme
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal procedure involves using a strap wrench to remove the filter, disconnecting a fuel line, and removing two bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump requires turning off the fuel supply, removing two tubes and two bolts, and removing the pump.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...ujjfdjkjskkmdm
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal procedure involves using a strap wrench to remove the filter, disconnecting a fuel line, and removing two bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump requires turning off the fuel supply, removing two tubes and two bolts, and removing the pump.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...fujsfskekem
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...uudfjjjskkemmd
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which requires removing mounting bolts and disconnecting lines.
The document provides instructions for removing and installing several fuel system components on a 225 excavator including:
- The fuel priming pump, including disconnecting lines and removing mounting bolts.
- The fuel filter base, involving removing bolts, lines, and filters.
- The fuel transfer pump, which has steps for removing mounting bolts and lines.
The document provides instructions for removing and disassembling components of the fuel transfer pump for a 225 EXCAVATOR powered by a 3304 engine, including:
- Removing the fuel transfer pump by disconnecting tubes and removing bolts.
- Disassembling the pump housing by removing the cover, spring, seals, valve assemblies, piston, sleeve, seals and bolts.
- Instructions specify cleaning parts and containing fluids during maintenance.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...ujjfdjkjskkmdm
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The removal procedure involves turning off the fuel supply, disconnecting tubes, and removing bolts to access the pump. The disassembly process describes removing springs, seals, sleeves, pistons, and other components from the pump housing. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...uudfjjjskkemmd
The document provides instructions for removing and disassembling the fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The removal procedure involves turning off the fuel supply, disconnecting tubes, and removing bolts to access the pump. The disassembly process describes removing springs, seals, sleeves, pistons, and other components from the pump housing. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...fujsjefkksekmme
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The procedures describe draining fuel, removing mounting bolts and hoses, installing replacement seals and gaskets, and reattaching components. Disassembly and assembly of the fuel transfer pump is also outlined.
Caterpillar cat 235 d excavator (prefix 8kj) service repair manual (8kj00001 ...fujsfskekem
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar 235D Excavator with a 3306 engine. The procedures describe draining fuel, removing mounting bolts and hoses, installing new seals and gaskets if needed, and reattaching components in the reverse order of removal. Disassembly and assembly of the fuel transfer pump internals is also outlined.
This document provides instructions for removing and disassembling the fuel transfer pump on a 225 EXCAVATOR powered by a 3304 engine. It describes removing the pump by disconnecting fuel lines and removing bolts. It then details disassembling the pump by removing springs, seals, valves, sleeves, pistons and other components. Precautions are provided to keep parts clean and contain fluids during maintenance.
Similar to Caterpillar Cat 229 EXCAVATOR (Prefix 1AG) Service Repair Manual (1AG00001 and up).pdf (20)
The documents provide instructions for servicing components of a Caterpillar 3306 engine used in a 235 excavator, including:
1) Procedures for removing and installing the automatic timing advance, which involves aligning gears, removing bolts and plates, and using support tools.
2) Disassembling the automatic timing advance unit by removing screws, plates, springs, weights and seals.
3) Reassembling the automatic timing advance unit by installing seals, gears, slides, weights, springs and plates.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00455-00...fujskekdjdmd
The document provides instructions for servicing components of a 235 excavator, including removing, disassembling, and reassembling the boom speed control valve, track brake valve, boom vent valve, swing combiner and relief valve, and pump selector valve. Removal instructions involve disconnecting lines and removing mounting bolts. Disassembly involves removing internal components like springs, stems, and plugs. Reassembly follows the reverse order and ensures proper installation of seals and adjustment of clearance sizes.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, technicians must disconnect harness assemblies, tubes, and hoses after relieving fuel pressure and marking components.
3. Installation requires connecting new fuel lines and hoses according to illustrated steps while maintaining cleanliness to prevent contamination.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It involves 20 steps including installing bearings and pins, attaching lifting devices, tightening nuts and bolts, and connecting hoses and harnesses. Tools required include a driver, lever puller, and bearing installer. Safety precautions are provided for working on pressurized hydraulic systems.
Caterpillar Cat 235 EXCAVATOR (Prefix 83X) Service Repair Manual (83X00001-00...fujskekdjdmd
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3306 engine, including:
- Removing and installing the fuel priming pump.
- Removing and installing the fuel filter base.
- Removing the fuel transfer pump.
- Disassembling and assembling the fuel transfer pump.
The instructions include safety notices and illustrations showing the component locations and part numbers. Technicians are directed to clean parts, replace worn gaskets, and properly contain fluids during the repair process.
Caterpillar Cat 235 EXCAVATOR (Prefix 64R) Service Repair Manual (64R00596-01...fujskekdjdmd
This document provides instructions for removing and installing the automatic timing advance component from a Caterpillar 3306 engine. It describes:
- Removing the front housing before removing the timing advance
- Using turning tools to align marks on gears and position the #1 piston at top dead center
- Removing two plugs and installing a tool to view inside the flywheel housing
- Removing a bolt to take off the timing advance
Komatsu HM400-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides parts information for an HM400-1L excavator with serial number range A10001-UP. It includes a list of major system sections and lists parts for the engine mounting, engine hoses, air intake and exhaust piping, air cleaner piping, and air cleaner inner parts. The parts lists include part numbers, descriptions, and quantities.
This document provides instructions for removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid on a 322C and 322C L excavator powered by a 3126 engine. The removal and installation procedures include multiple illustrations and steps such as disconnecting tubes, removing bolts and filters, inspecting parts, lubricating components, and reinstalling parts. Safety notices are provided to keep components clean and contain fluids.
Komatsu HM400-2 Articulated Dump Truck Parts Catalogue Manual - SN A11001 AND...fujskekdjdmd
This document provides part descriptions and numbers for engine components of the HM400-2 excavator from serial number A11001 and up. It includes sections for the cylinder head, rocker lever housing, rocker lever lever assembly, and rocker lever shaft assembly. Each section lists the relevant parts, descriptions, and quantities.
Komatsu HM350-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides a parts list for engine-related components of a HM350-1L machine with serial number A10001 or higher. It includes 20 main item categories from A to Y with numerous sub-items listed under each category. The parts list provides part numbers, descriptions, and other specifications for each item.
This document provides instructions for removing and installing final drive sprockets and travel brake valves on a 322-A excavator. It outlines the necessary safety procedures and gives step-by-step instructions for each job. To remove a final drive sprocket, tools must be installed under the frame and 16 bolts removed to lift the sprocket off. Travel brake valves are removed by releasing hydraulic pressure, disconnecting pipes, and removing 6 bolts. Detailed cleaning and installation steps are provided for both components.
Komatsu HM300-1L Articulated Dump Truck Parts Catalogue Manual - SN A10001 AN...fujskekdjdmd
This document provides parts information for an HM300-1L machine with serial number range A10001-UP. It includes a list of major system sections and references to more detailed parts pages for the engine and its components. Parts are identified by number, description, and other specifications. The sections covered include the engine and its mounting, hoses, piping, harness, damper, air cleaner, and other related parts.
CASE 845B 845B DHP Motor Grader Service Repair Manual.pdffujskekdjdmd
This document provides technical specifications and descriptions of components for 667TA engines, including the engine block, crankshaft, connecting rod, piston, and camshaft. It describes the main features of each component as well as their functions within the engine. It also provides diagrams to illustrate the components.
Caterpillar Cat 322C L 322CL Excavator (Prefix FED) Service Repair Manual (FE...fujskekdjdmd
The document provides instructions for disassembling the pilot valve of a 322C excavator. It describes 27 steps to fully disassemble the pilot valve, removing components like fittings, seals, covers, springs, spools and plugs. Cleanliness is important during disassembly and identification marks should be made on components. Personal protective equipment is recommended when releasing spring forces during disassembly.
Caterpillar Cat 322C L 322CL Hydraulic Excavator (Prefix HEK) Service Repair ...fujskekdjdmd
This document provides instructions for removing and installing components on a 322C L Hydraulic Excavator including:
1. Removing and installing a unit injector hydraulic pump, which involves disconnecting lines and reconnecting a harness.
2. Removing a turbocharger by removing bolts, nuts and disconnecting tubes.
3. Disassembling a turbocharger by removing housings and waste gate.
4. Assembling a turbocharger by positioning housings and cartridge assembly and reconnecting tubes.
5. Removing an exhaust manifold by first removing the turbocharger, then removing bolts and nuts.
CASE 750M Tier 4A (interim) Crawler Dozer Service Repair Manual (PIN NDDC7000...fujskekdjdmd
This document is a service manual for the 750M Crawler Dozer covering various systems including the engine, hydrostatic drive, brakes, hydraulics, tracks, cab climate control, electrical systems, lubrication, dozer blade, tools, and other components. It provides maintenance and repair instructions along with part numbers and safety information.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00984196
Fuel Priming Pump - Remove and Install
SMCS - 1258-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00500957
1. Turn the fuel supply line valve to the OFF position.
2. Remove the bolts and the washers that secure fuel priming pump (1) to base (5). Remove
gasket (4) .
3. Disconnect tube assembly (3) .
4. Remove two bolts (2), the washers and base (5) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00500957
2/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 1. Install base (5), the washers and two bolts (2) .
2. Connect tube assembly (3) to base (5) .
Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use new parts
for replacement.
3. Install gasket (4). Install fuel priming pump (1) and the bolts that secure the fuel priming
pump to base (5) .
4. Turn the fuel supply line valve to the ON position.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:56:37 UTC+0800 2019
3/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00917143
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
1/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00468389
1. Use Tool (A) to remove fuel filter (4) .
2. Disconnect fuel line (1) from fuel filter base (2) .
3. Remove two bolts (3), the washers, fuel filter base (2) and the gasket from the fuel injection
pump housing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 2 g00468389
Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use new parts
for replacement.
1. Install the gasket, fuel filter base (2), the washers and two bolts (3) on the fuel injection
pump housing.
2. Connect fuel line (1) to fuel filter base (2) .
3. Use Tool (A) to install fuel filter (4) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:57:33 UTC+0800 2019
3/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00905874
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g00462112
1. Turn the fuel supply line valve to the OFF position.
2. Remove tube assembly (2) and tube assembly (4) from fuel transfer pump (3) .
3. Remove bolts (1) and (5) from fuel transfer pump (3). Remove fuel transfer pump (3) and
the O-ring seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:58:28 UTC+0800 2019
2/2(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01003268
Fuel Transfer Pump - Disassemble
SMCS - 1256-015
Disassembly Procedure
Start By:
A. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 1 g00498289
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1. Remove bolts (2) and cover (1) from the fuel transfer pump housing.
Illustration 2 g00499040
2. Remove spring (4) from housing (3) .
2/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 3 g00498980
3. Remove O-ring seals (5) and (6) from cover (1) .
4. Remove valve assembly (7) from cover (1) .
Illustration 4 g00498334
5. Remove piston (12) from sleeve (10). Remove washer (15), valve assembly (14) and seal
(13) from piston (12) .
6. Remove sleeve (10) from housing (3). Remove O-ring seal (11) from sleeve (10) .
7. Remove guide and tappet assembly (9) and seal (8) from housing (3) .
3/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 5 g00498367
8. Remove two bolts (16), cover (17) and the seal from housing (3) .
Illustration 6 g00498470
9. Remove valve assembly (18) from housing (3) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:59:24 UTC+0800 2019
4/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01003269
Fuel Transfer Pump - Assemble
SMCS - 1256-016
Assembly Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g00498470
1. Install valve assembly (18) in housing (3) .
Illustration 2 g00498687
2. Put clean diesel fuel on seal (16). Install seal (16) on cover (17), as shown. Install the two
bolts that hold cover (17) to housing (3) .
Illustration 3 g00498334
2/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. NOTICE
The tappet and guide assembly must be serviced as a unit.
3. Put clean diesel fuel on seal (8). Install seal (8) on guide and tappet assembly (9). Install
guide and tappet assembly (9) in housing (3) .
4. Put clean diesel fuel on O-ring seal (11). Put O-ring seal (11) in position on sleeve (10).
Install sleeve (10) in housing (3) .
5. Install piston (12) in sleeve (10) .
6. Put clean diesel fuel on seal (13). Put seal (13), valve assembly (14) and washer (15) in
position in piston (12) .
Illustration 4 g00498980
7. Put clean diesel fuel on O-ring seals (5) and (6). Install O-ring seals (5) and (6) in cover (1).
Install valve assembly (7) in cover (1) .
3/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 5 g00499040
8. Install spring (4) in housing (3) .
Illustration 6 g00498289
9. Put cover (1) in position on the housing and install bolts (2) that hold the cover in position.
End By: Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:00:20 UTC+0800 2019
4/4(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00906240
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00462112
1. Install the O-ring seal and fuel transfer pump (3). Install bolts (1) and (5) .
2. Install tube assembly (2) and tube assembly (4) .
1/2(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 3. Turn the fuel supply line valve to the ON position.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:01:16 UTC+0800 2019
2/2(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00880175
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g00448807
1. Remove three bolts (1), (2) and (3) and the brackets from the fuel injection lines.
Illustration 2 g00448808
2. Disconnect six fuel injection line nuts (4) from the fuel injection pumps.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
2/5(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 3 g00448809
3. Hold the tops of fuel injector nozzles (5) with a wrench, as shown. Loosen the six fuel
injection line nuts at fuel injector nozzles (4) .
4. Disconnect the fuel injection line nuts at the fuel injector nozzles and remove the fuel
injection lines. Put caps and plugs on all openings immediately in order to prevent dirt from
contaminating the fuel system.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
3/5(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 1. Remove the protective covers from the fuel line connections. Place the fuel injection lines in
position on the engine. Tighten the fuel injection line nuts on the fuel injection pump and
the fuel injector nozzles finger tight.
Note: The nozzle assembly must be supported with a wrench.
Illustration 4 g00448810
2. Hold the tops of fuel injector nozzles (1) and use Tool (A) in order to tighten the fuel
injection line nuts to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 5 g00475542
3. Tighten six fuel injection line nuts (2) at the fuel injection pumps to a torque of 40 ± 7 N·m
(30 ± 5 lb ft).
4/5(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 6 g00475546
4. Install the brackets and three bolts (3), (4) and (5) that hold the fuel injection lines in
position.
5. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System -
Prime" topic (Maintenance Section).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:02:11 UTC+0800 2019
5/5(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048513
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6980 Fuel Nozzle Puller 1
B
FT-1533 Adapter 1
1P-0074 Slide Hammer Puller 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Do not allow the tops of the fuel injector nozzles to turn while the fuel
lines are loosened. The fuel injector nozzles will be damaged if the tops
of the fuel injector nozzle turns in the body. Defective fuel injector
nozzles will damage the engine due to incorrect spray patterns.
Illustration 1 g00448820
1. Remove bolt (1) and the clamp that secures the fuel injector nozzle.
Illustration 2 g00448821
2. Install Tool (A) over the fuel injector nozzle. Turn screw (2) counterclockwise until the
button on the end of the screw is just above the bolt hole for the clamp that holds down the
fuel injector nozzle.
3. Tilt Tool (A) upward so that the inside lip of the fuel nozzle puller is under the diameter of
the fuel injector nozzle.
4. Turn screw (2) clockwise until the button on Tool (A) goes into the bolt hole for the clamp
that holds down the fuel injector nozzle.
2/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. NOTICE
Do not exceed the recommended torque on the screw of the 6V-6980
Fuel Nozzle Puller in order to remove the nozzle. The nozzle will bend
or break if a torque greater than 17 N·m (13 lb ft) is applied.
5. Turn screw (2) clockwise in order to lift the fuel injector nozzle out of the bore. After the
fuel injector nozzle is loose in the bore of the cylinder head, move the fuel injector nozzle
upward and move the fuel injector nozzle downward. Moving the fuel injector nozzle helps
to loosen any carbon buildup and aids in the removal of the fuel injector nozzle.
6. When Tool (A) is used to remove the fuel injector nozzles, remove the carbon dam seal on
the end of the fuel injector nozzle.
Illustration 3 g00448822
7. If the fuel injector nozzle cannot be removed with Tool (A), Tool (B) must be used.
Note: When Tool (B) is used, it is likely that the fuel injector nozzle cannot be used again.
A new fuel injector nozzle will need to be installed as a replacement.
Note: Align the centerline of Tool (B) with the extended centerline of fuel injector nozzle
(3). This procedure will help prevent distortion of the fuel injector nozzle which can cause
the fuel injector nozzle to bend or break.
8. Remove the protective cap and install Tool (B) .
9. Use the slide hammer in order to remove fuel injector nozzle (3) .
10. Remove the compression seal from the fuel injector nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:03:07 UTC+0800 2019
3/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048591
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4979 Carbon Seal Installation Tool 1
B 8S-2245 Injector Cleaning Tool 1
C 6V-4089 Reamer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
30. Illustration 1 g00448903
1. Put carbon dam seal (1) on the small end of Tool (A). Expand carbon dam seal (1) by
sliding carbon dam seal (1) to the large end of Tool (A). Put Tool (A) against the fuel
injector nozzle. Slide carbon dam seal (1) from Tool (A) to the fuel injector nozzle. Slide
carbon dam seal (1) into position in the groove of the fuel injector nozzle, as shown. Use
Tool (A) in order to install carbon dam seal (1).
2. To clean the fuel injector nozzles, refer to Special Instruction, SEHS7292 for the use of
Tool (B) .
3. Install a new compression seal (2) on the fuel injector nozzle.
Illustration 2 g00448904
4. Use Tool (C) in order to clean the bore in the cylinder head for the fuel injector nozzle. Use
a wrench in order to turn Tool (C) .
2/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Illustration 3 g00448905
Illustration 4 g00448906
5. Align notch (3) in fuel injector nozzle (5) to the tab in clamp (4) during installation.
6. Install fuel injector nozzle (5). Ensure that the notch in the injector is aligned with the tab in
clamp (4) .
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:04:03 UTC+0800 2019
3/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
32. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903297
Fuel Ratio Control - Remove
SMCS - 1278-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
33. Illustration 1 g00460630
1. Disconnect fuel pressure line (3). Remove two bolts (2) .
2. Move fuel ratio control (1) upward in order to disengage the fuel ratio control from the lever
assembly in the governor.
Illustration 2 g00460631
3. Remove four O-ring seals (4) and screen assembly (5) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:04:59 UTC+0800 2019
2/2(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
34. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 229 EXCAVATOR 1AG
Configuration: 225B & 229 EXCAVATORS 1AG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903551
Fuel Ratio Control - Disassemble
SMCS - 1278-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
Start By:
A. Remove the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
35. Illustration 1 g00460737
1. Remove cover (1) and O-ring seal (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. In order to release the spring force, hold cover (3) in position and slowly remove the two
bolts that hold cover (3) in place.
Illustration 2 g00460791
3. Remove spring (4), washer (5) and diaphragm (6) from retainer (7). Remove retainer (7)
from housing (8) .
2/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
36. Illustration 3 g00460793
4. Remove nut (13) from valve extension (12) and remove valve extension (12) from retainer
(7). Remove stem (9) from valve extension (12). Remove spring (10) and O-ring seal (11)
from valve extension (12) .
Illustration 4 g00460795
5. Remove spring (14) and retainer (15) from housing (8) .
6. All parts should be cleaned and inspected. Replace all parts that are worn or damaged.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 16:05:55 UTC+0800 2019
3/3(W)
w
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...