This document provides instructions for disassembling and assembling the piston pump of a 226B3 skid steer loader. It lists 69 detailed steps for disassembly, including removing fittings, springs, seals, covers, and internal components. It then lists 17 steps for reassembling components like liners, seals, bearings, shafts, and covers. Measurements are to be recorded during disassembly for reference during reassembly. Tools required are also listed.
This document provides step-by-step instructions for disassembling the piston pump of a Caterpillar 226B3 skid steer loader. It lists 69 required steps and accompanying illustrations. The pump is first removed from the vehicle. Then various components like fittings, springs, seals, and plates are dismantled. Measurement and markings are made to aid reassembly. Bearings, shafts, and other internal parts are then extracted using specialized tools. The process is repeated for the opposite side.
This document provides disassembly instructions for a piston pump in a Caterpillar 226B3 skid steer loader powered by a C2.2 engine. It lists 71 steps to completely disassemble the pump, including removing fittings, springs, seals, bearings, shafts and other components. Various tools are required, and components need to be marked for proper reassembly. Safety precautions are noted for releasing spring forces. The document also provides illustrations supporting each step of the disassembly process.
This document provides disassembly instructions for a piston pump used in Caterpillar 226B3 skid steer loaders. It lists 70 steps to completely disassemble the pump along with required tools. Key components that are disassembled include fittings, springs, seals, covers, ports, linkages, bearings, pins, and actuators. Measurements and markings are noted throughout to aid reassembly.
This document provides instructions for disassembling a piston pump for a Caterpillar 226B3 skid steer loader for cleaning purposes. It lists 71 steps and required tools to remove components like fittings, springs, seals, bearings, and plates. Measurements are taken during removal to aid reassembly. Parts are marked to ensure correct installation.
This document provides instructions for disassembling a piston pump for a Caterpillar 226B3 skid steer loader for cleaning purposes. It lists 71 steps and required tools to remove components like fittings, springs, seals, bearings, and plates. Measurements are taken during removal to aid reassembly. Parts are marked to ensure correct installation.
This document provides step-by-step instructions for disassembling the piston pump of a Caterpillar 226B3 skid steer loader. It lists 71 steps and accompanying illustrations to remove components like fittings, springs, seals, bearings, and shafts. Required tools are also specified. The goal is to disassemble the pump for cleaning purposes only.
This document provides step-by-step instructions for disassembling the piston pump of a Caterpillar 226B3 skid steer loader. It lists 71 steps and accompanying illustrations to remove components like fittings, springs, seals, bearings, and shafts. Required tools are also specified. The goal is to disassemble the pump for cleaning purposes only.
This document provides instructions for disassembling a piston pump used in Caterpillar 216B3 skid steer loaders. It lists 71 steps and required tools to remove components like fittings, springs, seals, bearings, pins, plates, and shafts. Measurements are taken during removal to aid reassembly. Parts are marked to ensure correct installation. Safety warnings advise wearing protective equipment when removing parts with spring forces.
This document provides step-by-step instructions for disassembling the piston pump of a Caterpillar 226B3 skid steer loader. It lists 69 required steps and accompanying illustrations. The pump is first removed from the vehicle. Then various components like fittings, springs, seals, and plates are dismantled. Measurement and markings are made to aid reassembly. Bearings, shafts, and other internal parts are then extracted using specialized tools. The process is repeated for the opposite side.
This document provides disassembly instructions for a piston pump in a Caterpillar 226B3 skid steer loader powered by a C2.2 engine. It lists 71 steps to completely disassemble the pump, including removing fittings, springs, seals, bearings, shafts and other components. Various tools are required, and components need to be marked for proper reassembly. Safety precautions are noted for releasing spring forces. The document also provides illustrations supporting each step of the disassembly process.
This document provides disassembly instructions for a piston pump used in Caterpillar 226B3 skid steer loaders. It lists 70 steps to completely disassemble the pump along with required tools. Key components that are disassembled include fittings, springs, seals, covers, ports, linkages, bearings, pins, and actuators. Measurements and markings are noted throughout to aid reassembly.
This document provides instructions for disassembling a piston pump for a Caterpillar 226B3 skid steer loader for cleaning purposes. It lists 71 steps and required tools to remove components like fittings, springs, seals, bearings, and plates. Measurements are taken during removal to aid reassembly. Parts are marked to ensure correct installation.
This document provides instructions for disassembling a piston pump for a Caterpillar 226B3 skid steer loader for cleaning purposes. It lists 71 steps and required tools to remove components like fittings, springs, seals, bearings, and plates. Measurements are taken during removal to aid reassembly. Parts are marked to ensure correct installation.
This document provides step-by-step instructions for disassembling the piston pump of a Caterpillar 226B3 skid steer loader. It lists 71 steps and accompanying illustrations to remove components like fittings, springs, seals, bearings, and shafts. Required tools are also specified. The goal is to disassemble the pump for cleaning purposes only.
This document provides step-by-step instructions for disassembling the piston pump of a Caterpillar 226B3 skid steer loader. It lists 71 steps and accompanying illustrations to remove components like fittings, springs, seals, bearings, and shafts. Required tools are also specified. The goal is to disassemble the pump for cleaning purposes only.
This document provides instructions for disassembling a piston pump used in Caterpillar 216B3 skid steer loaders. It lists 71 steps and required tools to remove components like fittings, springs, seals, bearings, pins, plates, and shafts. Measurements are taken during removal to aid reassembly. Parts are marked to ensure correct installation. Safety warnings advise wearing protective equipment when removing parts with spring forces.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 226B3 SKID STEER LOADER AS2
Configuration: 226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i02358306
Piston Pump (Hydrostatic) - Disassemble
SMCS - 5070-015-H7
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7289 Ruler 1
B 1P-1861 Retaining Ring Pliers 1
C 138-7576 Link Brackets 2
D 8T-4956 Bolts (M12 - 1.75 - 35 MM) 2
E 8T-4223 Hard Washers (13.5 - 25.5 - 3 MM THK) 2
F 1P-0510 Driver Gp 1
G 1P-1854 Retaining Ring Pliers 1
H 1U-7600 Slide Hammer Puller Gp 1
J 1P-1860 Retaining Ring Pliers 1
K 8H-0663 Bearing Puller Gp 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Remove".
Note: The following procedure is intended for cleaning purposes only.
1/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00903455
1. Remove the fittings and connectors (1).
2. Remove speed sensing valve (2).
Illustration 2 g00903457
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove cover (3) and the spring for the crossover relief valve.
2/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00903461
Illustration 4 g00903467
4. Remove seat (4).
5. Note the orientation of spring (5).
6. Remove O-ring seal (6) from cover (3).
7. Remove back up ring (7) from cover (3).
8. Repeat Step 3 through Step 7 for the other covers.
Illustration 5 g00903500
3/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (8) for the charge relief valve.
Illustration 6 g00903502
Illustration 7 g00903503
10. Remove seat (9).
11. Remove shims (12).
12. Remove spring (13).
13. Remove seal (11) from plug (8).
4/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 14. Remove O-ring seal (10) from plug (8).
Illustration 8 g01178122
15. Use Tooling (A) to measure the distance from the stud to the nut. Record the distance for
assembly purposes.
Illustration 9 g00904929
16. Remove screws (14).
17. Remove nut (15).
18. Remove cover (16).
5/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00904930
19. Remove O-ring seal (17) from cover (16).
Illustration 11 g00904933
20. Use Tooling (B) to remove retaining ring (18). Remove actuator assembly (19).
Illustration 12 g00905018
21. Remove O-ring seal (20) from actuator assembly (19).
Illustration 13 g01054368
6/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 14 g01054370
Note: Keepers (21) must be marked for assembly. Do not mix keepers (21). The keepers are
not interchangeable.
22. Place actuator assembly (19) in a suitable press.
23. Remove keepers (21).
24. Remove shaft (26).
25. Remove spring retainer (22).
26. Remove spring (23).
27. Remove spring retainer (24).
28. Remove spacer (25).
29. Repeat Step 15 through Step 28 for the other cover.
7/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01178123
30. Remove caps (27).
31. Remove connectors (28).
32. Remove fitting (29).
33. Remove adapter (30).
Illustration 16 g00905035
Note: Mark the location of the notch in stud (31) by making a corresponding mark on the
housing for installation purposes.
34. Use Tooling (A) to measure the distance from stud (31) to nut (32). Record the distance for
assembly purposes.
35. Remove stud (31) and nut (32).
36. Repeat Step 34 and Step 35 for the other stud.
8/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g01178125
37. Remove connector (33).
38. Remove caps (34).
39. Remove fittings (35).
Illustration 18 g00905224
40. Use Tooling (A) to measure the distance from studs (36) to nuts (37). Record the distance
for assembly purposes.
41. Remove studs (36) and nuts (37).
9/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01178127
42. Remove bolts (38) from cover (39).
Illustration 20 g00973868
43. Use a suitable lifting device, Tooling (C), Tooling (D), and Tooling (E) to raise the piston
pump housing.
Illustration 21 g01178130
Note: Mark the port plates for assembly. Port plates are not interchangeable.
44. Remove port plate (40).
10/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g01178131
45. Remove plug (41) and the O-ring seal.
Illustration 23 g01178132
46. Remove slotted pin (42).
47. Repeat Step 45 and Step 46 for the other side.
Illustration 24 g01178133
48. Remove the rotating assembly and swashplate (43).
49. Remove linkage (44).
11/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 25 g01178135
50. Remove bearing assemblies (45) and (46).
51. Remove swashplate (47).
Illustration 26 g01178137
Note: Mark the reaction plate assembly and the barrel.
52. Remove reaction plate assembly (48) from barrel (49).
Illustration 27 g00905445
53. Remove the retainer and shims (51) from barrel (50).
12/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g00973870
Illustration 29 g00905448
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
54. Place barrel (50) in a suitable press.
55. Use Tooling (F) and Tooling (G) to remove retaining ring (52) and spring (55).
56. Remove washer (54).
57. Remove pins (53).
13/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 30 g00905648
58. Remove bearing races (56) from pins (57).
Illustration 31 g00905650
59. Remove O-ring seal (58).
60. Inspect dowel (59) for damage.
Illustration 32 g00905577
61. Use Tooling (B) to remove retaining ring (60).
14/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 33 g00973871
62. Use Tooling (H) to remove seal (61).
Illustration 34 g00905582
63. Use Tooling (B) to remove retaining ring (62).
Illustration 35 g00905653
64. Remove shaft (63).
15/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 36 g00973872
65. Use Tooling (J) to remove retaining ring (64).
Illustration 37 g00973873
66. Use a suitable press and Tooling (K) to remove bearing (65).
Illustration 38 g00906134
67. Remove bearing (66).
16/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 39 g00906511
68. Remove actuator (67).
Illustration 40 g00906515
69. Remove seal (68).
70. Remove liner (69).
71. Repeat Step 42 through Step 70 for the other end of the piston pump.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 13 08:45:38 UTC+0800 2019
17/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 226B3 SKID STEER LOADER AS2
Configuration: 226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i02362815
Piston Pump (Hydrostatic) - Assemble
SMCS - 5070-016-H7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7289 Ruler 1
B 1P-1861 Retaining Ring Pliers 1
F 1P-0510 Driver Gp 1
G 1P-1854 Retaining Ring Pliers 1
J 1P-1860 Retaining Ring Pliers 1
K 8H-0663 Bearing Puller Gp 1
L 2P-8301 Seal Guide 1
M 6V-2055 Grease 1
N 1U-6395 Grease 1
P 9S-3263 Thread Lock Compound 1
1/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 4 g00906130
5. Raise the temperature of bearing (65).
6. Use a suitable press and Tooling (K) to install bearing (65).
Illustration 5 g00905698
7. Use Tooling (J) to install retaining ring (64).
Illustration 6 g00905653
8. Install shaft (63).
3/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. Illustration 7 g00905582
9. Use Tooling (B) to install retaining ring (62).
Illustration 8 g00905650
10. Dowel (59) must be aligned with the piston pump housing during assembly.
11. Install O-ring seal (58).
Illustration 9 g00905648
12. Install bearing races (56) on pins (57).
4/17
226B3 Skid Steer Loader AS200001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...