In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 216B3 SKID STEER LOADER CD3
Configuration: 216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i02362815
Piston Pump (Hydrostatic) - Assemble
SMCS - 5070-016-H7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7289 Ruler 1
B 1P-1861 Retaining Ring Pliers 1
F 1P-0510 Driver Gp 1
G 1P-1854 Retaining Ring Pliers 1
J 1P-1860 Retaining Ring Pliers 1
K 8H-0663 Bearing Puller Gp 1
L 2P-8301 Seal Guide 1
M 6V-2055 Grease 1
N 1U-6395 Grease 1
P 9S-3263 Thread Lock Compound 1
1/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00906130
5. Raise the temperature of bearing (65).
6. Use a suitable press and Tooling (K) to install bearing (65).
Illustration 5 g00905698
7. Use Tooling (J) to install retaining ring (64).
Illustration 6 g00905653
8. Install shaft (63).
3/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00905582
9. Use Tooling (B) to install retaining ring (62).
Illustration 8 g00905650
10. Dowel (59) must be aligned with the piston pump housing during assembly.
11. Install O-ring seal (58).
Illustration 9 g00905648
12. Install bearing races (56) on pins (57).
4/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 10 g00905448
Illustration 11 g00973870
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
13. Install pins (53).
14. Install washer (54).
15. Place barrel (50) in a suitable press.
16. Use Tooling (F) and Tooling (G) to install spring (55) and retaining ring (52).
5/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00905445
17. Install the shims and retainer (51) to barrel (50).
Illustration 13 g01178137
Note: Align the reaction plate assembly with the barrel.
18. Install reaction plate assembly (48) to barrel (49).
Illustration 14 g01178135
19. Install swashplate (47).
20. Install bearing assemblies (45) and (46).
6/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g01178131
23. Note the orientation of linkage (44).
24. Pin (42A) must be centered in the hole in the pump housing.
25. Install slotted pin (42) so that the slotted pin engages pin (42A).
26. Install the plug and O-ring seal (41).
27. Repeat Step 24 through Step 26 for the other side.
Illustration 19 g01180101
Illustration 20 g01180102
8/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: The port plates are marked for assembly. Port plates are not interchangeable.
28. Apply Tooling (M) to port plate (40).
29. Align port plate (40) with the piston pump housing.
30. Install port plate (40).
31. Position linkage (44) in order to connect with actuator (67) during assembly.
32. Assemble the cover to the piston pump housing.
33. Repeat Step 1 through Step 32 for the other end of the piston pump.
Illustration 21 g01180104
34. Apply Tooling (N) to seal (61).
35. Use Tooling (L) to install seal (61).
Illustration 22 g00906796
36. Use Tooling (B) to install retaining ring (60).
9/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g01178127
37. Install bolts (38) to cover (39).
Illustration 24 g00905224
38. Position stud (36) and nut (37).
39. Use Tooling (A) to measure the distance from stud (36) to nut (37). Set the distance to the
recorded measurement from the disassembly.
Illustration 25 g01180160
40. Install fittings (35).
10/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 41. Install caps (34).
42. Install connector (33).
Illustration 26 g00905035
Note: Align the mark on the housing with the notch in stud (31).
43. Install stud (31) and nut (32). Set the distance to the recorded measurement from the
disassembly.
44. Use Tooling (A) to measure the distance from stud (31) to nut (32). Tighten the nut to a
torque of 30 ± 2 N·m (22 ± 1 lb ft).
45. Repeat Step 43 and Step 44 for the other stud.
Illustration 27 g01178123
46. Install adapter (30).
47. Install fitting (29).
48. Install connectors (28). Tighten the connectors to a torque of 22 ± 1 N·m (16 ± 1 lb ft).
49. Install caps (27).
11/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 28 g01054370
Illustration 29 g01054368
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Keepers (21) are marked for assembly. Do not mix keepers (21).
50. Install spacer (25).
51. Install spring retainer (24).
52. Install spring (23).
53. Install spring retainer (22).
54. Install shaft (26).
12/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 55. Place actuator assembly (19) in a suitable press.
56. Install keepers (21).
Illustration 30 g00905018
57. Install O-ring seal (20) on actuator assembly (19).
Illustration 31 g00904933
58. Install actuator assembly (19).
59. Use Tooling (B) to install retaining ring (18).
13/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 32 g00904930
60. Install O-ring seal (17) to cover (16).
Illustration 33 g00904929
61. Install cover (16).
62. Install nut (15).
63. Install screws (14).
Illustration 34 g01178122
64. Use Tooling (A) to measure the distance from the stud to the nut. Set the distance to the
recorded measurement from the disassembly.
14/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 35 g00903503
Illustration 36 g00903502
65. Install O-ring seal (10) to plug (8).
66. Install seal (11) to plug (8).
67. Install spring (13).
68. Install shims (12).
69. Install seat (9).
Illustration 37 g00903500
15/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 70. Install plug (8) for the charge relief valve. Tighten the plug to a torque of 70 ± 4 N·m
(52 ± 3 lb ft).
Illustration 38 g00903467
Illustration 39 g00903461
71. Install back up ring (7) to cover (3).
72. Install O-ring seal (6) to cover (3).
73. Note the orientation of spring (5).
74. Install seat (4).
16/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 40 g00903457
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
75. Install the spring and cover (3) for the crossover relief valve. Tighten the cover to a torque
of 160 ± 8 N·m (118 ± 6 lb ft).
76. Repeat Step 71 through Step 75 for the other covers.
Illustration 41 g00903455
77. Install speed sensing valve (2). Tighten the valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
78. Install the fittings and connectors (1).
End By:
a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 6 23:29:26 UTC+0800 2019
17/17216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 216B3 SKID STEER LOADER CD3
Configuration: 216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i07376431
Piston Pump (Hydrostatic) - Install
SMCS - 5070-012-H7
Installation Procedure
Table 1
Required Tool
Tool Part Number Part Description Qty
A 247-4296 Pump Support 1
B 138-7575 Link Bracket 1
C
159-3327(1)
Wrench Adapter 1
387-9124(2)
Wrench Adapter 1
(1)
For use with hex head bolts.
(2)
For use with 12 point head bolts
1/5216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 1 g01053175
1. Use a suitable lifting device, Tooling (B), and Tooling (A) to support piston pump (5).
2. Position piston pump (5). The weight of the piston pump is approximately 61 kg (134 lb).
2/5216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01053307
3. Use Tooling (C) to install bolt (6). Tighten bolts (6) to a torque of 160 ± 30 N·m
(118 ± 22 lb ft).
Note: Refer to Service Magazine, SEPD1272, "A New Bolt Is Used To Fasten The Hystat
Pump To The Engine" for bolt replacement information.
4. Repeat Step 3 for the other side.
5. Remove Tooling (A) and (B) from piston pump (5).
3/5216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 4 g01051392
9. Connect hose assemblies (1).
End By:
a. Install the gear pump.
b. Install hydraulic tank.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 6 23:30:25 UTC+0800 2019
5/5216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 216B3 SKID STEER LOADER CD3
Configuration: 216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine
Disassembly and Assembly
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3,
226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train
Media Number -UENR0251-07 Publication Date -01/07/2018 Date Updated -11/07/2018
i02787466
Control Manifold and Solenoid (Parking Brake) - Remove
and Install
SMCS - 5264-010; 5479-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ
6V-9508 Face Seal Plug (11/16 - 16 THD) 3
6V-9829 Cap Assembly (11/16 - 16 THD) 3
6V-9509 Face Seal Plug (13/16 - 16 THD) 2
6V-9830 Cap Assembly (13/16 - 16 THD) 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
b. Tilt the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
1/6216B3 Skid Steer Loader CD300001-UP (MACHINE) POWERED BY C2.2 Engine(S...
2019/10/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...