Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9G) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
140M 3 AWD MOTOR GRADER

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140M 3 AWD MOTOR GRADER N9G
Configuration: 140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems
Media Number -UENR3488-02 Publication Date -01/09/2018 Date Updated -24/09/2018
i07512054
Gerotor Motor (Circle Drive) - Assemble
SMCS - 5082-016; 5206-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all the components of the gerotor motor are clean prior to assembly. During the
assembly, check the condition of all the O-ring seals that are used in the motor. If any of the seals are
damaged, use new parts for replacement.
Illustration 1 g00926979
1/5
140M Series 3 Motor Grader-All Wheel Drive N9G00001-UP (MACHINE) POWERE...
2019/12/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2. Install bearing (18). Use a suitable press to press bearing (18) to a depth of 7.62 mm (0.300 inch)
below Surface (X).
3. Install lip seal (17). Press lip seal (17) in flush to 0.51 mm (0.020 inch) below face.
4. Install backup ring (19) and the shim to the motor assembly.
5. Install lip seal (20) to the motor assembly.
6. If equipped, install the needle bearing (13). Press the needle bearing to a depth of 2.92 mm
(0.115 inch) below Surface (Z). Install O-ring seal (21) to the motor assembly.
2/5
2019/12/31

7. Position the motor assembly so that Face (Y) is facing upward. Install two races (15) and bearing
(14) to shaft (16), as shown.
8. Install shaft (16) to the motor assembly.
9. Install link (11) and bearing (12) to the motor assembly.
10. Install spacer (10) and inner rotor (9) to the motor assembly.
11. Install the O-ring seal in outer rotor (7). Install pins (8) and outer rotor (7) to the motor assembly.
12. Install the O-ring seals on both sides of manifold (6). Install manifold (6) to the motor assembly.
3/5
2019/12/31

13. Install a new ring (5) to inner plate (4).
Note: Ring (5) is cone-shaped. The cone fits into the groove of inner plate (4).
14. Install inner plate (4). The seal ring should face the outer cap. Install outer plate (3) to the motor
assembly.
15. Install cap (2) and bolts (1) on to the motor assembly.
16. Tighten bolts (1) to a torque of 68 ± 7 N·m (50 ± 5 lb ft).
End By:
4/5
2019/12/31

Shutdown SIS
Previous Screen
i02798560
Gerotor Motor (Circle Drive) - Install
SMCS - 5082-012; 5206-012
Installation Procedure
Table 1
Required Tools
A 311-1362 Vacuum Cap 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
1/2
2019/12/31

1. Position the O-ring seal and gerotor motor (4). Install bolts (1).
2. Connect hose assemblies (3) and (2).
3. Remove Tooling (A).
4. Check the level of the hydraulic system. Refer to Operation and Maintenance Manual,
"Hydraulic System Oil Level - Check" for the correct procedure.
End By:
a. Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame
Lock - Separate and Connect".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 31 10:24:30 UTC+0800 2019
2/2
2019/12/31

Shutdown SIS
Previous Screen
i05508935
Circle Drive - Remove
SMCS - 5207-011
Removal Procedure
Table 1
Required Tools
A 138-7575 Link Bracket 3
Start By:
a. Remove the gerotor motor.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/5
2019/12/31

1. Bend lock (1) from nut (2). Remove nut (2), lock (1), and washer (3).
2. Remove O-ring seal (4). Remove nuts (5).
2/5
2019/12/31

3. Remove bolts (6).
3/5
2019/12/31

5. Attach Tooling (A) to circle drive (8). Attach a suitable lifting device to Tooling (A). The
weight of circle drive (8) is approximately 127 kg (280 lb).
6. Raise circle drive (8) and remove gear (9) and thrust washer (10).
4/5
2019/12/31

7. Remove Duo-Cone seal (11) from circle drive (8). Remove circle drive (8).
8. Remove Duo-Cone seal (12) from gear (9).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 31 10:25:26 UTC+0800 2019
5/5
2019/12/31

Shutdown SIS
Previous Screen
i05508896
Circle Drive - Disassemble
SMCS - 5207-015
Disassembly Procedure
Table 1
Required Tools
A Forcing Bolt 3/8-16 by 4 inch 2
B 138-7575 Link Bracket 1
C 8H-0663 Bearing Puller Gp 1
D
8B-7554 Bearing Cup Puller Gp 1
8B-7548 Push-Puller Tool Gp 1
Start By:
a. Remove the circle drive. Refer to Disassembly and Assembly, "Circle Drive - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1/9
2019/12/31

1. Remove coupling (1) from housing (3). Remove pin (2) from coupling (1).
2. Remove nuts (4). Remove bracket (5).
2/9
2019/12/31

3. Remove O-ring seal (7) and shims (8).
4. Remove bearing cup (6) from bracket (5).
5. Remove bolts (9) and cover (10).
3/9
2019/12/31

7. Install Tooling (A) and remove cover (12).
8. Remove plug (13) and O-ring seal (14) from cover (12).
9. Remove bearing (15) from cover (12).
4/9
2019/12/31

10. Install Tooling (B) on shaft assembly (16). Attach a suitable lifting device to Tooling (B).
The weight of shaft assembly (16) is approximately 32 kg (70 lb).
11. Remove shaft assembly (16). Remove Tooling (B).
5/9
2019/12/31

12. Remove remaining bolts (17) and retainer (18). Remove spacer (19) and shims (20).
13. Remove spring (21) and spacer (22).
6/9
2019/12/31

14. Remove gear (23) from shaft assembly (16). Remove friction discs (24) and discs (25) from
gear (23). Remove spacer (26).
7/9
2019/12/31

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

15. Remove thrust washer (27) and remove bearing (28).
16. Remove worm assembly (29) from housing (3).
17. Use Tooling (C) and a suitable press in order to remove bearings (31) from worm assembly
(29).
8/9
2019/12/31

Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9G) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9G) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9G) Service Repair Manual Instant Download.pdf (17)

More from jkdkkdsmmd

More from jkdkkdsmmd (20)

Recently uploaded

Recently uploaded (17)

Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9G) Service Repair Manual Instant Download.pdf