This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in steps:
1) Removing the valve lifters, timing gear cover, and bolts holding the camshaft gear.
2) Carefully removing the camshaft from the engine and gear if needed.
3) Cleaning and lubricating parts before installation.
4) Installing the camshaft gear, camshaft, washer, lock and bolts while ensuring proper timing marks are aligned.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fusefjskekkmem
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor. The procedure involves removing components like the valve lifters and timing gear cover. Marks are made on gears to ensure proper timing is maintained. The camshaft is then removed and lubricated before being reinstalled along with checking timing marks to ensure correct installation.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fjskefkemms
This document provides instructions for removing and installing various engine components on a 330B L EXCAVATOR, including:
- Exhaust manifold removal and installation requiring removal of the turbocharger and fuel lines.
- Inlet and exhaust valve removal and installation using specialized tools to compress springs.
- Removal and installation of valve guides, seats, and inserts using driver tools to precisely install components.
- Removal of the engine oil filter base requiring a strap wrench to remove the oil filter.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 936 e wheel loader (prefix 33z) service repair manual (33z030...ufjkskemfseol
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 936E wheel loader with a 3304 engine. It describes:
1) Removing the flywheel, crankshaft rear seal, oil pan plate bolts, and flywheel housing bolts to remove the housing.
2) Cleaning parts and installing the housing with bolts, checking gaskets, and reinstalling components like the oil pan plate.
3) The process involves several specific steps and the use of tools to safely and properly remove and replace the flywheel housing.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
The document describes Pulnikov EC's new IE5+ series of asynchronous motors that achieve the IE5 efficiency class. It provides an overview of the development of the IE5+ series, including the design strategies used to reach IE5 efficiency while maintaining normal starting torque, acceptable motor mass, and conventional manufacturing techniques. Motor data is presented for 2-pole, 4-pole, 6-pole, and 8-pole IE5+ motor designs ranging from 0.09 kW to 355 kW, including efficiency levels, power factors, torque characteristics, and materials usage. The economic benefits of replacing conventional IE3 motors with IE5+ motors are also discussed.
Caterpillar cat 950 b wheel loader (prefix 63r) service repair manual (63r000...fjsjjekdkme
This document provides instructions for removing and installing various components of a Caterpillar 3304B engine, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe disconnecting related components, removing mounting bolts, cleaning surfaces, installing new gaskets and seals, and torquing fasteners to the specified values. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fusefjskekkmem
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor. The procedure involves removing components like the valve lifters and timing gear cover. Marks are made on gears to ensure proper timing is maintained. The camshaft is then removed and lubricated before being reinstalled along with checking timing marks to ensure correct installation.
Caterpillar cat 330 b l excavator (prefix 1js) service repair manual (1js0000...fjskefkemms
This document provides instructions for removing and installing various engine components on a 330B L EXCAVATOR, including:
- Exhaust manifold removal and installation requiring removal of the turbocharger and fuel lines.
- Inlet and exhaust valve removal and installation using specialized tools to compress springs.
- Removal and installation of valve guides, seats, and inserts using driver tools to precisely install components.
- Removal of the engine oil filter base requiring a strap wrench to remove the oil filter.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 936 e wheel loader (prefix 33z) service repair manual (33z030...ufjkskemfseol
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 936E wheel loader with a 3304 engine. It describes:
1) Removing the flywheel, crankshaft rear seal, oil pan plate bolts, and flywheel housing bolts to remove the housing.
2) Cleaning parts and installing the housing with bolts, checking gaskets, and reinstalling components like the oil pan plate.
3) The process involves several specific steps and the use of tools to safely and properly remove and replace the flywheel housing.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
The document describes Pulnikov EC's new IE5+ series of asynchronous motors that achieve the IE5 efficiency class. It provides an overview of the development of the IE5+ series, including the design strategies used to reach IE5 efficiency while maintaining normal starting torque, acceptable motor mass, and conventional manufacturing techniques. Motor data is presented for 2-pole, 4-pole, 6-pole, and 8-pole IE5+ motor designs ranging from 0.09 kW to 355 kW, including efficiency levels, power factors, torque characteristics, and materials usage. The economic benefits of replacing conventional IE3 motors with IE5+ motors are also discussed.
Caterpillar cat 950 b wheel loader (prefix 63r) service repair manual (63r000...fjsjjekdkme
This document provides instructions for removing and installing various components of a Caterpillar 3304B engine, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe disconnecting related components, removing mounting bolts, cleaning surfaces, installing new gaskets and seals, and torquing fasteners to the specified values. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujjskeksmem
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujsjexswfksekmfm
This document provides instructions for removing and installing an engine oil pan on a 140G motor grader with a 3306 engine. It describes draining the engine oil, loosening nuts and tubes connected to the oil pan, and removing bolts and washers. When removing the oil pan, the instructions note to catch any fluids in suitable containers for proper disposal. Reinstallation involves replacing gaskets and bolts and tightening connections.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fjjskekdmmme
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujsefkskekmm
This document provides instructions for removing and installing an engine oil pan on a 140G motor grader with a 3306 engine. It describes draining the engine oil, loosening nuts and tubes connected to the oil pan, and removing bolts and washers. When removing the oil pan, the instructions note to catch any fluids in suitable containers for proper disposal. Reinstallation involves replacing gaskets and bolts and tightening connections.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujsjejfskekmm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fjkskekxsdcmdmme
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fjjskekertsmemm
This document provides instructions for removing and installing an engine oil pan on a 140G motor grader with a 3306 engine. It describes draining the engine oil, loosening nuts and tubes connected to the oil pan, and removing bolts and washers. When removing the oil pan, the instructions note to catch any fluids in suitable containers for proper disposal. Reinstallation involves replacing gaskets and bolts and tightening connections.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...ufjjsejklemd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...udjjfkkskemm
This document provides instructions for removing and installing the camshaft and camshaft bearings on a Caterpillar 3306 engine. It outlines the necessary steps including removing timing gears, camshaft drive gear, and camshaft. It emphasizes keeping parts clean and provides illustrations of the component locations. Installation involves aligning timing marks, lubricating parts, and reinstalling components in reverse order.
Caterpillar Cat 140G MOTOR GRADER (Prefix 72V) Service Repair Manual (72V0423...fujskkmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes:
1) Removing the valve lifters, timing gear cover, and bolts/lock to remove the camshaft.
2) Installing the camshaft drive gear, lubricating the lobes, and ensuring proper timing by aligning marks.
3) Tightening bolts and installing remaining parts.
The document provides instructions for removing and installing a camshaft on a D7G2 track-type tractor with a 3306 engine. It describes removing the valve lifters, timing gear cover, camshaft bolts and camshaft. When installing, it specifies applying lubricant to the lobes and oil to the bearings, aligning timing marks, and torquing bolts to the correct specification. Proper removal and installation of other components like the lifters and timing cover are also noted.
This document provides instructions for removing and installing an engine oil pan on a D7G2 track-type tractor with a 3306 engine. It describes draining the oil, loosening retaining nuts, removing bolts and washers, and removing the pan and gasket. Reinstallation involves cleaning parts, positioning the gasket and pan, and torquing the bolts and nuts to specifications.
The document provides instructions for removing and installing a camshaft on a D7G2 track-type tractor with a 3306 engine. The procedure involves removing components like the valve lifters and timing gear cover before removing the camshaft bolts and camshaft. Special marks are made on gears to ensure proper timing is maintained. The camshaft is then reinstalled along with any removed components.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...jfksekksmem
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor with a 3306 engine. It describes removing the valve lifters, timing gear cover, and bolts holding the camshaft gear. Marks should be made on gears to ensure proper timing is maintained. The camshaft is then carefully removed and lubricated before installation in reverse order while aligning timing marks. Removal and installation of camshaft bearings is also outlined.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...fjskemedcdmme
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor with a 3306 engine. It describes removing the valve lifters, timing gear cover, and bolts holding the camshaft gear. Marks should be made on gears to ensure proper timing on reinstallation. The camshaft is then carefully removed and lubricated before reinstallation and adjustment of timing marks. Removal and installation of the camshaft bearings is also described.
Troy bilt 700 series rider service repair manualfhjskemme
This document is a professional shop manual that provides instructions and guidance for trained technicians servicing and repairing MTD 700 series riding tractors. It covers a range of systems including the engine, steering, body panels, drive system, transaxle, electrical system, and more. Technicians are advised to follow all safety instructions and use common sense when working on equipment. The manual is intended as a supplemental reference and updates may be necessary.
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the Workman MD and MDX utility vehicles. It includes safety instructions, maintenance procedures, specifications, and repair information for the vehicle's engine, drivetrain, electrical system, chassis, and other components. Technicians are directed to refer to additional manuals for specific engine and system details.
The document is a service manual for the Workman MDE vehicle. It provides information to service technicians for troubleshooting, testing, and repairing major systems and components of the Workman MDE. It instructs technicians to refer to the operator's manual for operating, maintenance, and adjustment instructions. The manual contains several chapters covering safety, product records and maintenance, electrical systems, transaxles and brakes, chassis, and electrical diagrams. It provides specifications, troubleshooting guides, and procedures for servicing and repairing components.
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the Workman MD and MDX utility vehicles. It includes safety instructions, maintenance procedures, specifications, and repair information for the vehicle's engine, drivetrain, electrical system, chassis, and other components. Technicians are directed to refer to operator manuals for additional information.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
Toro pro core sr70 s service repair manualfhjskemme
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for Grades 1, 5, and 8 bolts as well as Classes 8.8 and 10.9 metric bolts. Reduced torque values are recommended for lubricated fasteners. Product records and maintenance procedures can be found in the operator's manual inserted at the end of the chapter.
More Related Content
Similar to Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v00823 04230)
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujjskeksmem
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujsjexswfksekmfm
This document provides instructions for removing and installing an engine oil pan on a 140G motor grader with a 3306 engine. It describes draining the engine oil, loosening nuts and tubes connected to the oil pan, and removing bolts and washers. When removing the oil pan, the instructions note to catch any fluids in suitable containers for proper disposal. Reinstallation involves replacing gaskets and bolts and tightening connections.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fjjskekdmmme
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujsefkskekmm
This document provides instructions for removing and installing an engine oil pan on a 140G motor grader with a 3306 engine. It describes draining the engine oil, loosening nuts and tubes connected to the oil pan, and removing bolts and washers. When removing the oil pan, the instructions note to catch any fluids in suitable containers for proper disposal. Reinstallation involves replacing gaskets and bolts and tightening connections.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fujsjejfskekmm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fjkskekxsdcmdmme
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...fjjskekertsmemm
This document provides instructions for removing and installing an engine oil pan on a 140G motor grader with a 3306 engine. It describes draining the engine oil, loosening nuts and tubes connected to the oil pan, and removing bolts and washers. When removing the oil pan, the instructions note to catch any fluids in suitable containers for proper disposal. Reinstallation involves replacing gaskets and bolts and tightening connections.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...ufjjsejklemd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes in detail:
1) Marking the gears to ensure proper timing when reinstalling the camshaft.
2) Removing the camshaft bolts and carefully pulling out the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before reinstalling.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v042...udjjfkkskemm
This document provides instructions for removing and installing the camshaft and camshaft bearings on a Caterpillar 3306 engine. It outlines the necessary steps including removing timing gears, camshaft drive gear, and camshaft. It emphasizes keeping parts clean and provides illustrations of the component locations. Installation involves aligning timing marks, lubricating parts, and reinstalling components in reverse order.
Caterpillar Cat 140G MOTOR GRADER (Prefix 72V) Service Repair Manual (72V0423...fujskkmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306 engine. It describes:
1) Removing the valve lifters, timing gear cover, and bolts/lock to remove the camshaft.
2) Installing the camshaft drive gear, lubricating the lobes, and ensuring proper timing by aligning marks.
3) Tightening bolts and installing remaining parts.
The document provides instructions for removing and installing a camshaft on a D7G2 track-type tractor with a 3306 engine. It describes removing the valve lifters, timing gear cover, camshaft bolts and camshaft. When installing, it specifies applying lubricant to the lobes and oil to the bearings, aligning timing marks, and torquing bolts to the correct specification. Proper removal and installation of other components like the lifters and timing cover are also noted.
This document provides instructions for removing and installing an engine oil pan on a D7G2 track-type tractor with a 3306 engine. It describes draining the oil, loosening retaining nuts, removing bolts and washers, and removing the pan and gasket. Reinstallation involves cleaning parts, positioning the gasket and pan, and torquing the bolts and nuts to specifications.
The document provides instructions for removing and installing a camshaft on a D7G2 track-type tractor with a 3306 engine. The procedure involves removing components like the valve lifters and timing gear cover before removing the camshaft bolts and camshaft. Special marks are made on gears to ensure proper timing is maintained. The camshaft is then reinstalled along with any removed components.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...jfksekksmem
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor with a 3306 engine. It describes removing the valve lifters, timing gear cover, and bolts holding the camshaft gear. Marks should be made on gears to ensure proper timing is maintained. The camshaft is then carefully removed and lubricated before installation in reverse order while aligning timing marks. Removal and installation of camshaft bearings is also outlined.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...fjskemedcdmme
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor with a 3306 engine. It describes removing the valve lifters, timing gear cover, and bolts holding the camshaft gear. Marks should be made on gears to ensure proper timing on reinstallation. The camshaft is then carefully removed and lubricated before reinstallation and adjustment of timing marks. Removal and installation of the camshaft bearings is also described.
Similar to Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v00823 04230) (15)
Troy bilt 700 series rider service repair manualfhjskemme
This document is a professional shop manual that provides instructions and guidance for trained technicians servicing and repairing MTD 700 series riding tractors. It covers a range of systems including the engine, steering, body panels, drive system, transaxle, electrical system, and more. Technicians are advised to follow all safety instructions and use common sense when working on equipment. The manual is intended as a supplemental reference and updates may be necessary.
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the Workman MD and MDX utility vehicles. It includes safety instructions, maintenance procedures, specifications, and repair information for the vehicle's engine, drivetrain, electrical system, chassis, and other components. Technicians are directed to refer to additional manuals for specific engine and system details.
The document is a service manual for the Workman MDE vehicle. It provides information to service technicians for troubleshooting, testing, and repairing major systems and components of the Workman MDE. It instructs technicians to refer to the operator's manual for operating, maintenance, and adjustment instructions. The manual contains several chapters covering safety, product records and maintenance, electrical systems, transaxles and brakes, chassis, and electrical diagrams. It provides specifications, troubleshooting guides, and procedures for servicing and repairing components.
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the Workman MD and MDX utility vehicles. It includes safety instructions, maintenance procedures, specifications, and repair information for the vehicle's engine, drivetrain, electrical system, chassis, and other components. Technicians are directed to refer to operator manuals for additional information.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
Toro pro core sr70 s service repair manualfhjskemme
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for Grades 1, 5, and 8 bolts as well as Classes 8.8 and 10.9 metric bolts. Reduced torque values are recommended for lubricated fasteners. Product records and maintenance procedures can be found in the operator's manual inserted at the end of the chapter.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
Toro pro core sr54 s service repair manualfhjskemme
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for grades 1, 5, and 8. Lubricated fasteners should be torqued to 25% less. Product records and maintenance procedures can be found in the operator's manual inserted at the end.
This document provides torque specifications and conversion factors for fasteners used on ProCore deep tine aerators. Standard torque values are listed for dry, zinc plated steel fasteners in both inch and metric sizes for Grades 1, 5, and 8 bolts as well as Classes 8.8 and 10.9 metric bolts. Reduced torque values are recommended for lubricated fasteners. Product records and maintenance procedures can be found in the operator's manual.
Toro pro core processor service repair manualfhjskemme
This service manual provides information to technicians for troubleshooting, testing, and repairing major systems and components of the ProCore Processor. It instructs technicians to refer to the operator's manual for operating instructions and maintenance. The manual includes chapters covering safety, product records and maintenance, the engine, hydraulic system, electrical system, chassis, and electrical diagrams. It is intended to help ensure the correct and safe operation of the ProCore Processor.
Toro groundsmaster 5910 service repair manualfhjskemme
This service manual provides information for troubleshooting, testing, and repairing major systems and components of the Groundsmaster 5900 and 5910 mowers. It contains chapters covering safety procedures, product records and maintenance, diesel engine systems, hydraulic systems, electrical systems, axles/brakes, chassis, cutting decks, operator cab, and foldout drawings. Technicians are instructed to follow safety procedures when jacking, servicing, or performing adjustments on the mower.
Toro groundsmaster 5900 service repair manualfhjskemme
This service manual provides information for troubleshooting, testing, and repairing major systems and components of the Groundsmaster 5900 and 5910 mowers. It contains chapters covering safety procedures, product records and maintenance, diesel engine systems, hydraulic systems, electrical systems, axles/brakes, chassis, cutting decks, operator cab, and foldout drawings. Technicians are instructed to follow safety procedures when jacking, servicing, or performing adjustments on the mower.
Toro groundsmaster 4300 d service repair manualfhjskemme
Here are the key steps for jacking the machine safely:
1. Park machine on a solid, level surface such as a concrete floor.
2. Remove any attachments that could interfere with safely raising the machine.
3. Chock or block the wheels to prevent rolling.
4. Use a jack and jack stands to support the raised machine. Do not rely on just the jack.
5. Position the jack and jack stands at designated lifting points to safely support the weight of the machine.
It is critical to follow these steps when raising the machine to change attachments, tires or perform other service under the machine. Properly supporting the machine is necessary to prevent it from moving or falling, which could
Toro groundsmaster 4110 d (model 30447) service repair manualfhjskemme
This document is a service manual for the Groundsmaster 4100-D and 4110-D. It contains chapters covering safety, product records and maintenance, the Kubota diesel engine, hydraulic system, electrical system, axles/brakes, chassis, cutting deck, operator cab, and foldout drawings. The safety chapter provides instructions for safe operation, maintenance, jacking, and contains safety and instruction decals. The document instructs technicians on troubleshooting, testing, adjusting and repairing major systems and components.
Toro groundsmaster 4100 d (model 30449) service repair manualfhjskemme
This document is a service manual for the Groundsmaster 4100-D and 4110-D. It contains chapters covering safety, product records and maintenance, the Kubota diesel engine, hydraulic system, electrical system, axles/brakes, chassis, cutting deck, operator cab, and foldout drawings. The safety chapter provides instructions for safe operation, maintenance, jacking, and contains safety and instruction decals. The document instructs technicians on troubleshooting, testing, adjusting and repairing major systems and components.
John deere ts and th 6x4 gator utility vehicle service repair manualfhjskemme
The document is a technical manual for a John Deere Gator utility vehicle. It provides an overview of the manual's contents and organization. The manual contains sections on specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety information. It notes that the manual is intended for experienced technicians and contains model-specific information to support the total product. Safety warnings are provided throughout regarding handling fluids, batteries, pressurized lines, rotating parts, and other hazards.
John deere 790 compact utility tractor service repair manualfhjskemme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. It contains sections on general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and operation/testing. The document provides specifications, repair/removal instructions, and diagnostic information to assist technicians in servicing these tractor models. Safety messages are included throughout and components are organized by system for easy reference.
Clark c500, y350 forklift service repair manualfhjskemme
This document provides instructions and guidelines for performing planned maintenance (PM) on Clark lift trucks. It outlines the importance of regular inspections and recommends using a PM report form to document the inspections. Safety precautions are described, such as disconnecting the battery before working on electrical components. A visual inspection process is outlined to check for issues like leaks, loose or damaged parts, and worn components. Inspections of specific systems and components like the overhead guard, carriage, forks, and hydraulic and electrical systems are recommended. Records of inspections should be submitted to maintenance authorities.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140G MOTOR GRADER 72V
Configuration: 140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01037991
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
B. Remove the timing gear cover. Refer to Disassembly and Assembly, "Front Housing -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00476744
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. The "C" mark on
the crankshaft gear will be aligned with the "C" mark on the camshaft gear.
Illustration 2 g00476743
Note: Put a mark on the teeth of the fuel injection pump drive gear and the idler gear at
location (A). This will help to keep the engine timing correct during the removal and the
installation of the camshaft. Put a mark on the teeth of the idler gear and camshaft gear (2)
at location (B). When the camshaft is installed, the engine timing will be correct when the
mark at location (A) is aligned with the mark at location (B) and the "C" mark on the
crankshaft gear is aligned with the "C" mark on the camshaft gear.
2. Remove the bolts, the lock and washer (1) .
Illustration 3 g00535590
2/5140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. NOTICE
Do not damage the lobes or the bearings when the camshaft is
removed.
3. Carefully remove camshaft (3) from the engine.
4. If necessary, remove the bolts that hold camshaft drive gear (2) to the camshaft and remove
the gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00535590
1. Put camshaft drive gear (2) in position on the end of camshaft (3). Install the bolts that hold
camshaft drive gear (2) to camshaft (3). Tighten the bolts to a torque of 55 ± 7 N·m (41 ± 5
lb ft).
NOTICE
Do not damage the lobes or the bearings when the camshaft is installed.
3/5140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 2. Put 8T-2998 Camshaft Lubricant on the camshaft lobes only and put clean engine oil on the
bearing journals.
Note: During the installation of camshaft (3), rotate the camshaft in both directions in order
to prevent binding in the camshaft bearing bores.
3. Carefully install camshaft (3) into the engine.
Illustration 5 g00476743
Illustration 6 g00476744
4. Make sure that the mark on the teeth of the fuel injection pump drive gear and the idler gear
are in alignment at location (A). Make sure that the mark on the teeth of the idler gear and
camshaft gear (2) are in alignment at location (B). Align the "C" marks on the crankshaft
gear and camshaft gear (2). When all of the timing marks are in alignment the engine timing
is correct.
4/5140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 5. Install washer (1), the lock and the two bolts that hold the camshaft in position in the
engine.
End By:
a. Install the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Install the timing gear cover. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 25 00:47:13 UTC+0800 2020
5/5140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140G MOTOR GRADER 72V
Configuration: 140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02473351
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the Flywheel Housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
B. Remove the Oil Pan Plate. Refer to Disassembly and Assembly, "Oil Pan Plate - Remove
and Install".
C. Remove the Camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00478567
1. Use Tool (A) to remove the camshaft bearing from the cylinder block. Start with the front
bearings and work to the rear bearing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g00478567
1. Use Tool (A) to install the camshaft bearings in the 3304B and 3306B cylinder block.
Note: The camshaft bearings in the 3304B have pressure lubrication. The intermediate
camshaft bearings and the rear camshaft bearings in the 3306B have splash lubrication.
2. Install the camshaft bearings in the 3304B cylinder block, as follows:
(a) Install the front bearing to a depth of 0.57 ± 0.5 mm (0.022 ± 0.02 inch). Ensure that the
oil holes are in a horizontal position and that the camshaft bearing joint is at the top of the
engine. The camshaft bearing joint can not be more than 15° degrees from vertical in either
direction.
(b) Install the center bearing to a depth of 303.2 ± 0.5 mm (11.94 ± 0.02 inch). Ensure that
the oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder
block.
(c) Install the rear bearing to a depth of 604.9 ± 0.5 mm (23.81 ± 0.02 inch). Ensure that the
oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder block.
Illustration 3 g00478822
1. Install the camshaft bearings in the 3306B cylinder block, as follows:
2. Install front bearing (B) to a depth of 0.5 ± 0.5 mm (.02 ± .02 inch). Ensure that the oil holes
are in a horizontal position and that the camshaft bearing joint is at the top of the engine.
The camshaft bearing joint cannot be more than 15 degrees from the vertical position in
either direction.
3. Install the remainder of the bearings. Install the bearings to the dimensions that are given
from the front face of the cylinder block: (C) 154.0 ± 0.5 mm (6.06 ± .02 inch), (D) 303.2 ±
3/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 0.5 mm (11.94 ± .02 inch), (E) 601.7 ± 0.5 mm (23.69 ± .02 inch) and (F) 903.4 ± 0.5 mm
(35.57 ± .02 inch).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
b. Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
c. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 25 00:48:08 UTC+0800 2020
4/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140G MOTOR GRADER 72V
Configuration: 140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00974130
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1. Drain the engine oil from the engine into a suitable container for storage or disposal.
1/3140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00541041
2. Loosen nut (4) and move the overflow tube away from the oil level gauge guide. Loosen nut
(3) and remove the oil level gauge guide from the engine.
3. Remove bolts (1) and the washers that hold the engine oil pan in position. Remove engine
oil pan (2) and the gasket from the engine oil pan plate.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00541041
1. Put the gasket and engine oil pan (2) in position on the engine oil pan plate. Install bolts (1)
and the washers that hold the engine oil pan in position.
2/3140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 2. Install the oil level gauge guide and tighten nut (3). Fasten the overflow tube to the oil level
gauge guide and tighten nut (4) .
3. Fill the crankcase with engine oil to the proper level. Refer to Operation and Maintenance
Manual, "Refill Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 25 00:49:04 UTC+0800 2020
3/3140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140G MOTOR GRADER 72V
Configuration: 140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111802
Engine Balancer Shaft - Remove and Install
SMCS - 1220-010-JF
Removal Procedure
Start By:
A. Remove the front housing cover. Refer to Disassembly and Assembly, "Front Housing
Cover - Remove".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/3140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Dispose of all fluids according to local regulations and mandates.
Note: The oil pan plate has been removed for photo purposes only.
Illustration 1 g00590442
1. Remove plates (2) that hold the balancer shaft in the cylinder block.
2. Remove balancer shafts (1) from the cylinder block.
Installation Procedure
Illustration 2 g00590449
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Install the balancer shafts in each side of the cylinder block.
2. Install plates (2) and the bolts that hold the balancer shafts in position in the cylinder block.
Note: Ensure that the balancer shafts are in time before the oil pump is installed.
End By:
a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
b. Install the front housing cover. Refer to Disassembly and Assembly, "Front Housing Cover
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 25 00:50:00 UTC+0800 2020
3/3140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140G MOTOR GRADER 72V
Configuration: 140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01135419
Engine Balancer Shaft Bearings - Remove and Install
SMCS - 1220-010-BD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove".
B. Remove the balancer shaft. Refer toDisassembly and Assembly, "Balancer Shaft -
Remove".
C. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing
Remove" .
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00602186
Use Tool (A) to remove the six balancer shaft bearing. Pull the balancer shaft bearings toward the
flywheel end of the engine.
Installation Procedure
Illustration 2 g00602186
2/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Illustration 3 g00602205
(A) The front bearing depth is 0.8 ± 0.5 mm (0.03 ± 0.02 inch).
(B) The center bearing depth is 290.6 ± 0.5 mm (11.44 ± 0.02 inch).
(C) The rear bearing depth is 601.0 ± 0.5 mm (23.66 ± 0.02 inch).
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
3/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 1. Install the balancer shaft front bearing with Tool (A). Ensure that the holes in the bearings
are aligned with the holes in the cylinder block. The bearing must be 0.8 ± 0.5 mm (0.03 ±
0.02 inch) inside the front face of the cylinder block after installation.
2. Install the balancer shaft center bearing with Tool (A). Ensure that the holes in the bearings
are aligned with the holes in the cylinder block. The bearing must be 290.6 ± 0.5 mm (11.44
± 0.02 inch) inside the front face of the cylinder block after installation.
3. Install the balancer shaft rear bearing with Tool (A). Ensure that the holes in the bearings
are aligned with the holes in the cylinder block. The bearing must be 601.0 ± 0.5 mm (23.66
± 0.02 inch) inside the front face of the cylinder block after installation.
4. Check the bore of the bearings. The balancer shaft bearing bore must be 53.05 ± 0.06 mm
(2.089 ± 0.002 inch) after installation.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Install" .
b. Install the balancer shaft. Refer to Disassembly and Assembly, "Balancer Shaft - Remove
and Install".
c. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 25 00:50:55 UTC+0800 2020
4/4140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140G MOTOR GRADER 72V
Configuration: 140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00912474
Cylinder Liner - Remove
SMCS - 1216-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-0812 Cylinder Liner Puller 1
1U-6317 Bridge 1
1U-6319 Socket 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00474523
1. Turn the crankshaft until two of the pistons are at the bottom center. Remove two
connecting rod cap bolts (2) from each rod. Remove connecting rod caps (4) .
2. Tap connecting rod (3) away from the crankshaft with a soft hammer. Remove bearing half
(1) .
Illustration 2 g00474623
3. Use tool (A) to remove cylinder liners (5) .
4. Remove the pistons and connecting rods from the cylinder liners.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 25 00:51:51 UTC+0800 2020
2/2140G MOTOR GRADER 72V00823-04230 (MACHINE) POWERED BY 3306 ENG...
2020/2/25https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...