This document provides instructions for disassembling the transmission of a 12M 3 AWD motor grader. It lists over 30 steps and required tools to remove components like the transmission, housing, seals, plates, sensors, clutches and gears. Diagrams illustrate each step, and notes are included to mark orientations of parts for reassembly. Safety precautions are mentioned for compressed springs.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...f8usejkdmmd8i
This document provides the disassembly procedure for a transmission in a 12M 3 motor grader. It lists over 35 steps to completely disassemble the transmission along with required tools. Cautions are provided regarding contained fluids, identification marks, and spring forces. Detailed illustrations accompany each step showing the parts being removed.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual (N9R000...tingrm81805
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 50 individual parts that must be removed, and provides illustrations and detailed steps for removing each part.
3) Special tools are required to remove many components, and springs apply force that can cause injury, so protective equipment is advised.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...ze6074xunong
This document provides the disassembly procedure for a transmission in a 12M 3 motor grader. It lists over 35 steps and required tools to fully disassemble the transmission. Key components that are disassembled include the housing, clutch assembly, gear assembly, seals, sensors and electrical components. Detailed illustrations accompany each step to show how to remove parts in the correct order while noting part orientations for reassembly. Safety notices are included to properly handle springs and contain fluids.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual (N9R000...hdjsjndndnd
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 45 steps and required tools to disassemble the transmission and its components.
3) The disassembly process involves removing housing, plates, seals, sensors, gears, and other internal components. Precautions are provided to handle springs and heavy parts safely during disassembly.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...f8seodkdmdmed3
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 45 steps and required tools to disassemble the transmission and its components.
3) The disassembly process involves removing housing, plates, seals, sensors, gears, and other internal components. Precautions are provided to handle springs and heavy parts safely during disassembly.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...hean57759707
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 45 steps and required tools to disassemble the transmission and its components.
3) Safety notices are included throughout to warn of heavy parts that require lifting devices and springs that can cause injury if not properly released.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual (F9B000...hdjsjndndnd
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to fully disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position the transmission and which components to remove at each step. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...ze6074xunong
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to completely disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position and support the transmission during disassembly. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...f8usejkdmmd8i
This document provides the disassembly procedure for a transmission in a 12M 3 motor grader. It lists over 35 steps to completely disassemble the transmission along with required tools. Cautions are provided regarding contained fluids, identification marks, and spring forces. Detailed illustrations accompany each step showing the parts being removed.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual (N9R000...tingrm81805
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 50 individual parts that must be removed, and provides illustrations and detailed steps for removing each part.
3) Special tools are required to remove many components, and springs apply force that can cause injury, so protective equipment is advised.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...ze6074xunong
This document provides the disassembly procedure for a transmission in a 12M 3 motor grader. It lists over 35 steps and required tools to fully disassemble the transmission. Key components that are disassembled include the housing, clutch assembly, gear assembly, seals, sensors and electrical components. Detailed illustrations accompany each step to show how to remove parts in the correct order while noting part orientations for reassembly. Safety notices are included to properly handle springs and contain fluids.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual (N9R000...hdjsjndndnd
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 45 steps and required tools to disassemble the transmission and its components.
3) The disassembly process involves removing housing, plates, seals, sensors, gears, and other internal components. Precautions are provided to handle springs and heavy parts safely during disassembly.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...f8seodkdmdmed3
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 45 steps and required tools to disassemble the transmission and its components.
3) The disassembly process involves removing housing, plates, seals, sensors, gears, and other internal components. Precautions are provided to handle springs and heavy parts safely during disassembly.
Caterpillar Cat 12M 3 MOTOR GRADER (Prefix N9R) Service Repair Manual Instant...hean57759707
1) The document provides disassembly instructions for a 12M 3 motor grader transmission.
2) It lists over 45 steps and required tools to disassemble the transmission and its components.
3) Safety notices are included throughout to warn of heavy parts that require lifting devices and springs that can cause injury if not properly released.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual (F9B000...hdjsjndndnd
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to fully disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position the transmission and which components to remove at each step. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...ze6074xunong
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to completely disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position and support the transmission during disassembly. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...f8seodkdmdmed3
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to completely disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position and support the transmission during disassembly. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...f8usejkdmmd8i
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to completely disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position and support the transmission during disassembly. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...hean57759707
This document provides the disassembly procedure for a 12M 2 motor grader transmission. It lists over 50 steps to disassemble the transmission along with required tools. Key components that are disassembled include the housing, clutch assemblies, gear assemblies, seals, sensors, pistons and various discs, plates, rings and washers. Detailed illustrations accompany each step to show how to remove the individual parts in the proper sequence. Safety notices are included regarding releasing spring forces and containing fluids.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...ze6074xunong
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to remove components like clutches, seals, sensors, gears and housings. Detailed illustrations accompany each step to show how to position the transmission and what fasteners and tools to use. Safety notices are included to handle components and release spring forces properly.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...f8usejkdmmd8i
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to remove components like clutches, seals, sensors, housings and more. Detailed illustrations accompany each step and special safety notices are included. Required tools are listed as well as part numbers.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual (R9P000...tingrm81805
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to disassemble various components of the transmission, including removing housing components, seals, sensors, clutches, and gears. Detailed illustrations accompany each step to show how to position the transmission and which fasteners and tools to use. Safety notices are included regarding containing fluids, wearing protective equipment, and noting part orientations for reassembly.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual (R9P000...hdjsjndndnd
1) The document provides disassembly instructions for a 12M 2 motor grader transmission. It lists over 50 individual steps and required tools to fully disassemble the transmission.
2) Key components that must be removed include the transmission housing, clutch assemblies, gears, seals, bearings, pistons, and various discs, plates, rings, and washers. Detailed illustrations are provided to identify each part.
3) Safety notices are included, warning of heavy component weights and potential for parts to be propelled by released spring forces during disassembly. Orientations of parts must be noted for proper reassembly.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...hean57759707
1) The document provides disassembly instructions for a 12M 2 motor grader transmission. It lists over 50 individual steps and required tools to fully disassemble the transmission.
2) Key components that must be removed include the transmission housing, clutch assemblies, gears, seals, bearings, pistons, and various discs, plates, rings, and washers. The order and orientation of components is noted for reassembly.
3) Safety precautions are provided, such as wearing protective equipment when compressing springs or lifting heavy parts, and ensuring fluids are contained. Technicians are instructed to mark harnesses and note the installation positions of parts.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...f8seodkdmdmed3
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to remove components like seals, springs, plates, sensors and housings. Detailed illustrations accompany each step to show precisely which components are being removed. Safety notices are included to warn of heavy component weights and spring forces during disassembly. Required specialty tools are also listed to correctly complete each removal step.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fujsekfksemmaq
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission, control module, yoke assembly, housing, clutch assemblies, gears, seals, sensors and other parts. Detailed instructions are given for using various tools to compress, remove, and separate components. Safety notices are included and components are to be marked for correct reinstallation.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fusjefjskekem
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission, control module, yoke assembly, housing, clutch assemblies, gears, seals, sensors and other parts. Detailed instructions are given for using various tools to compress, remove, and separate components. Safety notices are included and components are to be marked for correct reinstallation.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fjjsekfxswzksmem
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. These steps include removing components like the housing, clutch assemblies, gears, seals, pistons, and sensors. Diagrams are provided to illustrate where each component is located and how to remove it. Proper notation of component orientation and quantities is emphasized for reassembly.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fujsfkkskekmem
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission, control module, yoke assembly, housing, clutch assemblies, gears, seals, sensors and other parts. Detailed instructions are given for using various tools to compress, remove, and separate components. Safety notices are included and components are to be marked for correct reinstallation.
Caterpillar Cat 315B L Excavator (Prefix 5SW) Service Repair Manual Instant D...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the travel motor of a 315B L excavator. The disassembly process involves 23 steps to remove components such as the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly process reverses the disassembly steps and includes cleaning and lubricating components before installing them back into the travel motor housing. Precise positioning and identification marks are needed to ensure components are reinstalled in their original locations.
The document provides instructions for removing and installing several fuel system components on a 225 EXCAVATOR powered by a 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
The instructions include safety notices and illustrations showing the component locations and part names. Technicians are directed to clean parts with diesel fuel and replace any worn or damaged seals during installation.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...f8seodkdmdmed3
The document provides instructions for removing and installing a diesel particulate filter on a Caterpillar 308E2 CR Mini Hydraulic Excavator powered by a C3.3B engine. It describes removing temperature sensors, tube assemblies, and brackets to detach the filter. Instructions are given to clean the filter or install a new one, and then reassemble the components in reverse order, applying anti-seize and torquing bolts to the specified values.
Caterpillar Cat 308E2SR Mini Hydraulic Excavator (Prefix SR8) Service Repair ...f8seodkdmdmed3
This document provides instructions for removing and installing various components of a Caterpillar 308E2SR Mini Hydraulic Excavator powered by a C3.3B engine, including the electronic unit injector, turbocharger, exhaust gas recirculation valve, pressure sensor, and fumes disposal filter. The procedures include lists of required tools and step-by-step instructions detailing how to remove, clean, and install each part while maintaining proper orientation and torque specifications.
Caterpillar Cat 315F L and 315F LCR Excavator (Prefix TDY) Service Repair Man...f8seodkdmdmed3
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 17 specific disassembly steps, including draining fluids, removing covers, valves, springs, seals, and other parts. Special safety notices are included to warn of potential hazards like released spring forces or pressurized hydraulic systems. Detailed illustrations accompany each step to show how to position the components and which fasteners, seals, and other pieces to remove.
Caterpillar Cat 308E2 Mini Hydraulic Excavator (Prefix F8C) Service Repair Ma...f8seodkdmdmed3
This document provides instructions for removing and installing a flywheel housing on a mini hydraulic excavator. The key steps are:
1. Remove the flywheel and rear crankshaft seal.
2. Install guide studs and lifting brackets to remove the flywheel housing bolts.
3. Lift the flywheel housing off using the lifting device.
4. Inspect and replace any worn bearings or seals.
5. Reinstall by reversing the removal steps, applying liquid gasket to the crankcase seam.
Caterpillar Cat 308D Mini Hydraulic Excavator (Prefix FYC) Service Repair Man...f8seodkdmdmed3
The document provides instructions to remove and install the support (swing boom) on a 308D Mini Hydraulic Excavator. The removal procedure involves using tools to remove 14 bolts and pins to separate the support assembly from the machine. The installation procedure specifies using tools to reinstall the support assembly components in the reverse order of removal and applying grease to surfaces before reinstallation.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 311F LRR excavator. It lists the required tools and outlines 16 steps to disassemble the components, including draining fluids, removing covers, plates, seals, springs, and pistons. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
More Related Content
Similar to Caterpillar Cat 12M 3 AWD MOTOR GRADER (Prefix N9B) Service Repair Manual Instant Download.pdf
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...f8seodkdmdmed3
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to completely disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position and support the transmission during disassembly. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...f8usejkdmmd8i
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 30 steps to completely disassemble the transmission along with required tools. These steps include removing components like the yoke assembly, retaining rings, seals, plates, sensors, clutches, gears, and housing. Detailed illustrations are provided to show how to position and support the transmission during disassembly. Safety notices are also included regarding containing fluids, wearing protective equipment, and handling compressed springs.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix F9B) Service Repair Manual Instant...hean57759707
This document provides the disassembly procedure for a 12M 2 motor grader transmission. It lists over 50 steps to disassemble the transmission along with required tools. Key components that are disassembled include the housing, clutch assemblies, gear assemblies, seals, sensors, pistons and various discs, plates, rings and washers. Detailed illustrations accompany each step to show how to remove the individual parts in the proper sequence. Safety notices are included regarding releasing spring forces and containing fluids.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...ze6074xunong
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to remove components like clutches, seals, sensors, gears and housings. Detailed illustrations accompany each step to show how to position the transmission and what fasteners and tools to use. Safety notices are included to handle components and release spring forces properly.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...f8usejkdmmd8i
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to remove components like clutches, seals, sensors, housings and more. Detailed illustrations accompany each step and special safety notices are included. Required tools are listed as well as part numbers.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual (R9P000...tingrm81805
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to disassemble various components of the transmission, including removing housing components, seals, sensors, clutches, and gears. Detailed illustrations accompany each step to show how to position the transmission and which fasteners and tools to use. Safety notices are included regarding containing fluids, wearing protective equipment, and noting part orientations for reassembly.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual (R9P000...hdjsjndndnd
1) The document provides disassembly instructions for a 12M 2 motor grader transmission. It lists over 50 individual steps and required tools to fully disassemble the transmission.
2) Key components that must be removed include the transmission housing, clutch assemblies, gears, seals, bearings, pistons, and various discs, plates, rings, and washers. Detailed illustrations are provided to identify each part.
3) Safety notices are included, warning of heavy component weights and potential for parts to be propelled by released spring forces during disassembly. Orientations of parts must be noted for proper reassembly.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...hean57759707
1) The document provides disassembly instructions for a 12M 2 motor grader transmission. It lists over 50 individual steps and required tools to fully disassemble the transmission.
2) Key components that must be removed include the transmission housing, clutch assemblies, gears, seals, bearings, pistons, and various discs, plates, rings, and washers. The order and orientation of components is noted for reassembly.
3) Safety precautions are provided, such as wearing protective equipment when compressing springs or lifting heavy parts, and ensuring fluids are contained. Technicians are instructed to mark harnesses and note the installation positions of parts.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9P) Service Repair Manual Instant...f8seodkdmdmed3
This document provides the disassembly procedure for a transmission in a 12M 2 motor grader. It lists over 35 individual steps to remove components like seals, springs, plates, sensors and housings. Detailed illustrations accompany each step to show precisely which components are being removed. Safety notices are included to warn of heavy component weights and spring forces during disassembly. Required specialty tools are also listed to correctly complete each removal step.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fujsekfksemmaq
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission, control module, yoke assembly, housing, clutch assemblies, gears, seals, sensors and other parts. Detailed instructions are given for using various tools to compress, remove, and separate components. Safety notices are included and components are to be marked for correct reinstallation.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fusjefjskekem
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission, control module, yoke assembly, housing, clutch assemblies, gears, seals, sensors and other parts. Detailed instructions are given for using various tools to compress, remove, and separate components. Safety notices are included and components are to be marked for correct reinstallation.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fjjsekfxswzksmem
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 50 steps to fully disassemble the transmission along with required tools. These steps include removing components like the housing, clutch assemblies, gears, seals, pistons, and sensors. Diagrams are provided to illustrate where each component is located and how to remove it. Proper notation of component orientation and quantities is emphasized for reassembly.
Caterpillar cat 160 m motor grader (prefix d9t) service repair manual (d9t000...fujsfkkskekmem
This document provides disassembly instructions for the transmission of a 160M Motor Grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission, control module, yoke assembly, housing, clutch assemblies, gears, seals, sensors and other parts. Detailed instructions are given for using various tools to compress, remove, and separate components. Safety notices are included and components are to be marked for correct reinstallation.
Similar to Caterpillar Cat 12M 3 AWD MOTOR GRADER (Prefix N9B) Service Repair Manual Instant Download.pdf (14)
Caterpillar Cat 315B L Excavator (Prefix 5SW) Service Repair Manual Instant D...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the travel motor of a 315B L excavator. The disassembly process involves 23 steps to remove components such as the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly process reverses the disassembly steps and includes cleaning and lubricating components before installing them back into the travel motor housing. Precise positioning and identification marks are needed to ensure components are reinstalled in their original locations.
The document provides instructions for removing and installing several fuel system components on a 225 EXCAVATOR powered by a 3304 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing the fuel transfer pump
- Disassembling and assembling the fuel transfer pump
The instructions include safety notices and illustrations showing the component locations and part names. Technicians are directed to clean parts with diesel fuel and replace any worn or damaged seals during installation.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...f8seodkdmdmed3
The document provides instructions for removing and installing a diesel particulate filter on a Caterpillar 308E2 CR Mini Hydraulic Excavator powered by a C3.3B engine. It describes removing temperature sensors, tube assemblies, and brackets to detach the filter. Instructions are given to clean the filter or install a new one, and then reassemble the components in reverse order, applying anti-seize and torquing bolts to the specified values.
Caterpillar Cat 308E2SR Mini Hydraulic Excavator (Prefix SR8) Service Repair ...f8seodkdmdmed3
This document provides instructions for removing and installing various components of a Caterpillar 308E2SR Mini Hydraulic Excavator powered by a C3.3B engine, including the electronic unit injector, turbocharger, exhaust gas recirculation valve, pressure sensor, and fumes disposal filter. The procedures include lists of required tools and step-by-step instructions detailing how to remove, clean, and install each part while maintaining proper orientation and torque specifications.
Caterpillar Cat 315F L and 315F LCR Excavator (Prefix TDY) Service Repair Man...f8seodkdmdmed3
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 17 specific disassembly steps, including draining fluids, removing covers, valves, springs, seals, and other parts. Special safety notices are included to warn of potential hazards like released spring forces or pressurized hydraulic systems. Detailed illustrations accompany each step to show how to position the components and which fasteners, seals, and other pieces to remove.
Caterpillar Cat 308E2 Mini Hydraulic Excavator (Prefix F8C) Service Repair Ma...f8seodkdmdmed3
This document provides instructions for removing and installing a flywheel housing on a mini hydraulic excavator. The key steps are:
1. Remove the flywheel and rear crankshaft seal.
2. Install guide studs and lifting brackets to remove the flywheel housing bolts.
3. Lift the flywheel housing off using the lifting device.
4. Inspect and replace any worn bearings or seals.
5. Reinstall by reversing the removal steps, applying liquid gasket to the crankcase seam.
Caterpillar Cat 308D Mini Hydraulic Excavator (Prefix FYC) Service Repair Man...f8seodkdmdmed3
The document provides instructions to remove and install the support (swing boom) on a 308D Mini Hydraulic Excavator. The removal procedure involves using tools to remove 14 bolts and pins to separate the support assembly from the machine. The installation procedure specifies using tools to reinstall the support assembly components in the reverse order of removal and applying grease to surfaces before reinstallation.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 311F LRR excavator. It lists the required tools and outlines 16 steps to disassemble the components, including draining fluids, removing covers, plates, seals, springs, and pistons. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 305E Mini Hydraulic Excavator (Prefix XFA) Service Repair Man...f8seodkdmdmed3
The document provides instructions for installing and removing parts of the main hydraulic pump, selector valve, and control manifold on a 305E Mini Hydraulic Excavator. It lists the required tools and parts and includes illustrations and step-by-step instructions for assembly and disassembly. Key steps include installing bearings and seals, connecting hoses and harnesses, and removing manifolds and valves by disconnecting connections and removing bolts. Safety warnings are provided to prevent injury when handling spring loaded parts.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...f8seodkdmdmed3
This document provides instructions for removing and installing the fuel filter, fuel filter base, engine oil filter, and engine oil filter base on a 307D Mini Hydraulic Excavator. It lists the required tools and safety precautions and provides detailed step-by-step procedures with illustrations for removing, disassembling, assembling, and installing each component. Special attention is paid to cleanliness, containment of fluids, and proper tightening of bolts and connectors.
This service repair manual provides instructions for removing and installing the fuel injection pump on Caterpillar 3054 engines. It includes:
1) A list of required tools including timing pins and tamper resistant tools.
2) Removal steps which begin by removing the water pump and fuel lines, and involve using timing pins to align holes and loosen bolts while ensuring the engine is at the correct timing.
3) Installation steps which involve checking the O-ring seal, lubricating it, mounting the pump and securing it with flange nuts while aligning the timing gear, and using timing pins to verify correct timing alignment before tightening bolts.
This document provides instructions for removing, disassembling, assembling, and installing pistons and connecting rods in a 3054 engine. The removal process involves removing the cylinder head, oil pump, and piston cooling jets before pushing the pistons and connecting rods out of the cylinder block. Disassembly requires using tools to remove the piston rings and pins. Assembly requires lubricating and pressing components, and ensuring proper ring and bearing installation. Installation involves cleaning, lubricating, and inserting the assembled pistons and connecting rods into the cylinder liner and connecting to the crankshaft.
Caterpillar Cat 306E2 Mini Hydraulic Excavator (Prefix E2W) Service Repair Ma...f8seodkdmdmed3
The document provides instructions for removing and installing the governor, camshaft, and fuel injection pump on a Caterpillar 306E2 Mini Hydraulic Excavator. It describes removing the bolts and brackets holding the camshaft in place, and pressing out bearings to disassemble it. Reassembly involves pressing in new bearings and installing retaining rings and brackets. The fuel injection pump removal involves disconnecting fuel lines and electrical connections, then removing mounting bolts.
Caterpillar Cat 305E2CR Mini Hydraulic Excavator (Prefix R5C) Service Repair ...f8seodkdmdmed3
This document provides instructions for removing and installing various engine components on a Caterpillar 305E2CR Mini Hydraulic Excavator including:
- Removing the flywheel using lifting tools and bolts
- Inspecting the flywheel and ring gear for wear and replacing if needed
- Removing the crankshaft rear seal carrier cover and lip seal
- Removing the flywheel housing by removing mounting bolts
- Removing the crankshaft pulley using sockets and a puller
- Removing the crankshaft front seal, key and sleeve from the crankshaft
- Removing the idler gear after aligning timing marks using a special tool
The instructions include safety notices and
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...f8seodkdmdmed3
This document provides instructions for removing and installing various engine components on a Caterpillar 304E2CR Mini Hydraulic Excavator KC400001-UP powered by a C2.4 engine. The components include the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, and front housing. The procedures provide detailed illustrations and specify any required tools and torque specifications.
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix FSC) Service Repair M...f8seodkdmdmed3
The document provides step-by-step instructions for disassembling the final drive and travel motor of a 305.5E Mini Hydraulic Excavator. It lists 38 steps to remove components like gears, bearings, pistons, seals, and plates using various tools. Dismantling involves removing plugs, bolts, rings, and other fasteners while taking precautions for parts under spring pressure. The goal is to fully separate the final drive and travel motor assemblies for inspection or repair.
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...f8seodkdmdmed3
The document provides instructions for servicing components of a 305.5E Mini Hydraulic Excavator engine. It includes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The document contains illustrations and specifies required tools for each procedure. Safety notices are provided to keep parts clean and contain fluids during repair.
Caterpillar Cat 306E Mini Hydraulic Excavator (Prefix FHL) Service Repair Man...f8seodkdmdmed3
This document provides instructions for removing and installing various engine components on a 306E Mini Hydraulic Excavator including:
- Removing and installing the camshaft and valve lifters
- Removing and installing the camshaft gear
- Removing and installing the engine oil pan
- Removing and installing the pistons and connecting rods
- Disassembling the pistons and connecting rods
The document includes diagrams and step-by-step instructions and notes on tools needed and proper procedure.
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix FKY) Service Repair M...f8seodkdmdmed3
The document provides instructions for removing and installing various track components on a 305.5E Mini Hydraulic Excavator, including the front idler, recoil spring, hydraulic track adjusters, and installing the track. The procedures describe using lifting devices and tools to remove heavy components like the idler assembly. Detailed illustrations show the component parts and steps to compress springs, remove nuts and seals, and reinstall components in the correct order. Safety warnings are included to wear protective equipment when working with tensioned springs.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including the turbocharger, exhaust manifold, inlet manifold, and inlet and exhaust valve springs. The removal and installation procedures describe loosening bolts and hoses, plugging openings to prevent contamination, cleaning surfaces, and replacing gaskets. Tools required are listed for each procedure.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12M 3 AWD MOTOR GRADER N9B
Configuration: 12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Power Train
Media Number -UENR3483-02 Publication Date -01/01/2014 Date Updated -10/04/2018
i07077362
Transmission - Disassemble
SMCS - 3030-015; 3159-015; 3176-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 422-8733 Jack Stand Gp 3
C 1U-9202 Lever Puller Hoist 1
D 1P-1863 Retaining Ring Pliers 1
E 308-3470 Jack Stand Gp 2
F 140-7742 Sleeve 1
G 154-6181 Forcing Bolt 2
H FT-2769 Table 1
J 4C-8156 Lifting Fixture 1
K
1U-6410 Three Jaw Puller 1
1P-0510 Driver Gp 1
L 9U-7480 Compressing Tube 1
5P-7970 Nut 1
8T-4224 Hard Washer 1
- 1
1/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Bolt
M8 - 1.25 by 460mm
M 8B-7548 Push-Puller Tool Gp 1
N 2P-8312 Retaining Ring Pliers 1
P
1P-2321 Combination Puller 1
1P-0510 Driver Gp 1
R
189-0408 Shackle As 1
3E-3882 Eyebolt 1
S
126-7175 Push-Puller Tool Gp 1
4C-5653 Threaded Adapter 1
1P-0510 Driver Gp 1
Start By:
a. Remove the transmission.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all harness assemblies for installation purposes.
2/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g01386565
1. Attach Tooling (A) and a suitable lifting device to transmission (1). The weight of
transmission (1) is approximately 862 kg (1900 lb). Use Tooling (A) and the suitable lifting
device to position transmission (1) onto Tooling (B). Remove hose assembly (2).
Illustration 2 g01386568
2. Remove bolts (3) to remove control module (4) and spacers (5).
3/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01386574
3. Remove yoke assembly (6).
Illustration 4 g01386575
4. Remove retaining ring (7).
5. Remove cup (8). Remove O-ring seal (9).
Illustration 5 g01386579
6. Attach Tooling (A), Tooling (C), and a suitable lifting device to transmission (1). Use
Tooling (A), Tooling (C), and the suitable lifting device to position transmission (1) onto
Tooling (B) and suitable cribbing. Position transmission (1) with the output shaft upward.
4/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g01386585
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (10) to remove plate assembly (11).
Illustration 7 g01386589
8. Remove lip seal (12).
5/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 8 g01386599
9. Use Tooling (D) to remove retaining ring (13). Remove coned disc springs (14).
Note: Note the orientation of coned disc springs (14) for assembly purposes.
Illustration 9 g01386610
10. Remove O-ring seal (15) and piston (16).
6/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 10 g01386621
11. Remove piston seal (17). Remove piston seal (18).
Illustration 11 g01386624
12. Disconnect harness assembly (19) and harness assembly (21). Remove guard (20).
Illustration 12 g01386632
13. Remove bolts (22). Use two people to remove housing (23). The weight of housing (23) is
approximately 20 kg (45 lb).
7/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 13 g01386646
14. Remove pressure sensor (24) and the O-ring seal. Remove solenoid (25).
Illustration 14 g01386658
15. Remove O-ring seal (26), O-ring seal (27), O-ring seal (28), O-ring seal (29), and O-ring
seal (30).
Illustration 15 g01386662
16. Remove seal (31).
Illustration 16 g01386663
8/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 17. Remove friction discs (32) and clutch plates (33).
Note: Note the quantity and the order of friction discs (32) and clutch plates (33) for
assembly purposes.
18. Remove O-ring seals (34) and dowels (35).
Illustration 17 g01386675
19. Remove retaining ring (36). Remove hub (37).
Illustration 18 g01386684
20. Attach Tooling (A), Tooling (C), Tooling F, and a suitable lifting device to transmission (1).
Use Tooling (A), Tooling (C), Tooling (F), and the suitable lifting device to position
transmission (1) onto Tooling (B) and Tooling (E) with the output shaft downward. The
weight of transmission (1) is approximately 862 kg (1900 lb).
9/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWERE...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01386730
21. Remove bolt (38) to remove speed sensor (39) and guard (40).
Illustration 20 g01386747
22. Remove bolts (41) to remove speed sensor (42) and speed sensor (43).
Illustration 21 g01386749
23. Remove cover (44).
10/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g01386757
24. Remove bolts (45) to remove speed sensor (46) and speed sensor (47).
Illustration 23 g01386764
25. Attach Tooling (A), Tooling (C), and a suitable lifting device to housing (49). The weight of
housing (49) is approximately 136 kg (300 lb). Remove bolts (48).
26. Use Tooling (A), Tooling (C), and the suitable lifting device to remove housing (49).
Note: If necessary, use Tooling (G) to assist in removal of housing (49).
Illustration 24 g01386792
11/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 27. Remove O-ring seal (50). Remove bolts (51) and the locks. Remove tube assembly (52) and
the O-ring seal.
Illustration 25 g01386795
28. Remove bolts (53) to remove seal carrier (54). Remove bolts (55) to remove seal carrier
(56).
Illustration 26 g01386797
29. Remove seal rings (57). Remove O-ring seals (58). Repeat this step for the remaining seal
carrier.
Illustration 27 g01386811
12/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g01386815
30. Use Tooling (J) and a suitable lifting device to remove clutch assembly (59) and clutch
assembly (60). The combined weight of clutch assembly (59) and clutch assembly (60) is
approximately 163 kg (360 lb).
31. Position clutch assembly (59) and clutch assembly (60) onto Tooling (H). If necessary,
support clutch assembly (60) with suitable cribbing.
32. Remove Tooling (J) to separate clutch assembly (59) from clutch assembly (60).
Illustration 29 g01386827
33. Use Tooling (K) to remove bearing (61) and rotor (62) from clutch assembly (59).
Note: Be sure to attach Tooling (K) to gear assembly (63) to prevent damage to rotor (62).
13/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 30 g01386841
34. Remove thrust washer (64) and gear assembly (63).
Note: Note the orientation of thrust washer (64) for assembly purposes.
Illustration 31 g01386992
35. Remove bearing sleeves (65) from gear assembly (63).
Illustration 32 g01386993
36. Remove thrust washer (66).
14/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: Note the orientation of thrust washer (66) for assembly purposes.
Illustration 33 g01386997
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
37. Use Tooling (L) to compress hub assembly (67). Remove lock rings (68) and two half rings
(69) (not shown).
Note: Note the orientation of lock rings (68) and two ring halves (69) for assembly
purposes.
Illustration 34 g01387088
15/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 38. Remove hub assembly (67), friction discs (70), and clutch plates (71).
Note: Note the order of friction discs (70) and clutch plates (71) for assembly purposes.
Illustration 35 g01387093
39. Remove wave spring (72) and piston (73).
Illustration 36 g01387119
40. Remove seal rings (74) and (75) from piston (73).
Illustration 37 g01387137
16/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 41. Use a suitable lifting device to turn over clutch assembly (59). The weight of clutch
assembly (59) is approximately 59 kg (130 lb).
Illustration 38 g01387150
Illustration 39 g01387221
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
42. Use Tooling (M) to remove bearing (76). Remove thrust washer (77), thrust disc (78), and
gear assembly (79).
Note: Note the orientation of thrust disc (78) for assembly purposes.
17/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 40 g01387228
43. Remove thrust disc (80), washer (81), half rings (82), and lock rings (83).
Note: Note the orientation of thrust disc (80) for assembly purposes.
Illustration 41 g01387232
44. Remove hub assembly (84). Remove friction discs (85) and clutch plates (86).
Note: Note the orientation of friction discs (85) and clutch plates (86) for assembly
purposes.
18/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 42 g01387235
45. Use Tooling (N) to remove retaining ring (87).
46. Remove balance piston (88). Remove seal ring (89) from balance piston (88).
47. Remove springs (90).
48. Remove piston (91). Remove seal rings (92) and (93) from piston (91).
Illustration 43 g01387511
49. Use Tooling (K) to remove inner bearing (94) from clutch assembly (60). Remove thrust
disc (95) and gear (96).
Note: Note the orientation of thrust disc (95) for assembly purposes.
Illustration 44 g01387520
50. Remove thrust disc (97) and gear assembly (98) from clutch assembly (60).
Note: Note the orientation of thrust disc (97) for assembly purposes.
19/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 45 g01387526
51. Remove sleeve bearing (99) from gear assembly (98).
Illustration 46 g01387528
52. Remove thrust disc (100) and washer (101) from clutch assembly (60).
Note: Note the orientation of thrust disc (100) for assembly purposes.
Illustration 47 g01387541
20/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
53. Use Tooling (L) to compress hub assembly (102). Remove lock rings (103) and two half
rings (104) (not shown).
Note: Note the orientation of lock rings (103) and two ring halves (104) for assembly
purposes.
Illustration 48 g01387556
54. Remove hub assembly (102), friction discs (105), and clutch plates (106) from clutch
assembly (60).
Note: Note the orientation of friction discs (105) and clutch plates (106) for assembly
purposes.
21/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 49 g01387573
55. Remove wave spring (107) and piston (108) from clutch assembly (60).
Illustration 50 g01387580
56. Remove seal rings (109) and (110) from piston (108).
Illustration 51 g01387592
57. Use a suitable lifting device to turn over clutch assembly (60) onto Tooling (H). The weight
of clutch assembly (60) is approximately 54 kg (120 lb).
22/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 52 g01387595
58. Use Tooling (P) to remove inner bearing (111), thrust disc (112), and gear (113) from clutch
assembly (60).
Note: Note the orientation of thrust disc (112) for assembly purposes.
Illustration 53 g01387755
59. Remove thrust disc (114) and gear assembly (115).
Note: Note the orientation of thrust disc (114) for assembly purposes.
23/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 54 g01387765
60. Remove bearing (116) from gear assembly (115).
Illustration 55 g01387820
61. Remove thrust disc (117) and washer (118).
Note: Note the orientation of thrust disc (117) for assembly purposes.
Illustration 56 g01387824
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
24/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 62. Use Tooling (L) to compress hub assembly (119). Remove lock rings (120) and two half
rings (121) (not shown).
Note: Note the orientation of lock rings (120) and two ring halves (121) for assembly
purposes.
Illustration 57 g01387846
63. Remove hub assembly (119), friction discs (122), and clutch plates (123).
Note: Note the orientation of friction discs (122) and clutch plates (123) for assembly
purposes.
Illustration 58 g01387852
64. Remove wave spring (124) and piston (125).
25/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 59 g01387858
65. Remove seal rings (126) and (127) from piston (125).
Illustration 60 g01387876
66. Use Tooling (P) to remove inner bearing (128) and gear (129) from input shaft assembly
(130). This is necessary at this time so that you can remove the remaining two clutch
assemblies.
Illustration 61 g01387884
67. Remove bolts (131) to remove seal carrier (132).
26/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 62 g01387892
68. Remove seal rings (133). Remove O-ring seals (134).
Illustration 63 g01387895
69. Attach Tooling (R) and a suitable lifting device to clutch assembly (135). The weight of
clutch assembly (135) is approximately 61 kg (135 lb). Use Tooling (R) and the suitable
lifting device to remove clutch assembly (135). Position clutch assembly (135) onto Tooling
(H).
Illustration 64 g01387898
27/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 70. Use Tooling (P) to remove inner bearing (136), spacer (137), and gear (138) from clutch
assembly (135).
Illustration 65 g01388168
71. Remove spacer (139) and thrust disc (140) from clutch assembly (135).
Note: Note the orientation of thrust disc (140) for assembly purposes.
72. Remove gear assembly (141), thrust disc (142), and washer (143).
Note: Note the orientation of thrust disc (142) for assembly purposes.
Illustration 66 g01388185
73. Remove bearing (144) from gear assembly (141).
28/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 67 g01388208
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
74. Use Tooling (L) to compress hub assembly (145). Remove lock rings (146) and two half
rings (147) (not shown).
Note: Note the orientation of lock rings (146) and two ring halves (147) for assembly
purposes.
Illustration 68 g01388240
75. Remove hub assembly (145), friction discs (148), and clutch plates (149).
29/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Note: Note the orientation of friction discs (148) and clutch plates (149) for assembly
purposes.
Illustration 69 g01388243
76. Remove wave spring (150) and piston (151).
Illustration 70 g01388246
77. Remove seal rings (152) and (153) from piston (151).
Illustration 71 g01388263
30/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
33. Illustration 72 g01388277
78. Use a suitable lifting device to turn over clutch assembly (135) onto Tooling (H). The
weight of clutch assembly (135) is approximately 41 kg (90 lb).
79. Attach Tooling (S) to clutch assembly (135) to remove inner bearing (154). Remove thrust
race (155), thrust disc (156), thrust disc (157), and gear assembly (158).
Note: Note the orientation of thrust discs (156) and (157) for assembly purposes.
Illustration 73 g01388296
80. Remove roller bearing assembly (159) and thrust disc (160) from clutch assembly (135).
Note: Note the orientation of thrust disc (160) for assembly purposes.
31/45
12M Series 3 Motor Grader-All Wheel Drive N9B00001-UP (MACHINE) POWER...
2021/3/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...