What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12H MOTOR GRADER CBK
Configuration: 12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -RENR4108-16 Publication Date -01/06/2018 Date Updated -26/06/2018
i01973878
Transmission - Disassemble
SMCS - 3002-015; 3030-015; 3159-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 154-6181 Forcing Screw 2
C 6V-5221 Bolt 1
D 4C-8156 Fixture 1
E 6V-3918 Bolt 1
F 4C-8157 Fixture 2
G 1U-6405 Three Jaw Puller 1
H 1U-6341 Threaded Rod 1
J 5P-7970 Nut 1
K 9U-7479 Compressing Tube 1
L 5B-0637 High Idle Nut 1
5F-7353 Washer 1
1B-4207 Full Nut 2
5F-7369 Puller Leg 2
3H-0465 Push-Puller Plate 2
1/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 5F-7366 Screw 1
5P-4808 Cap 2
1U-9895 Crossblock 1
M
9S-9151 Block 2
1B-4206 Nut 4
8B-7552 Bolt 2
N 1U-6343 Threaded Rod 1
P 6V-8149 Nut 1
Q 2P-8312 Pliers 1
R
1P-2326 Screw 1
1P-2325 Head 1
3H-0462 Bolt and Nut 4
8H-0709 Strap 4
5F-7373 Jaw 3
S 3E-3882 Eyebolt 1
Start By:
a. Remove the transmission control valve. Refer to Disassembly and Assembly, "Transmission
Control Valve - Remove".
b. Remove the parking brake. Refer to Disassembly and Assembly, "Parking Brake -
Remove".
c. Remove the transmission speed sensor.
d. Remove the transmission oil pump. Refer to Disassembly and Assembly, "Gear Pump
(Transmission Charging and Scavenge) - Remove".
e. Remove the transmission magnetic screen base. Refer to Disassembly and Assembly,
"Magnetic Screen - Remove and Install".
2/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00623100
1. Place transmission (1) level on the floor.
2. Remove 12 bolts (2), four covers, and the O-ring seals from transmission case assembly (3).
3. Remove 41 bolts (4) from the transmission case assembly (3).
Illustration 2 g00623105
Note: Identify the location of seal carrier (5) in the transmission case assembly (3) for
assembly purposes.
4. Remove two bolts (6) from seal carrier (5).
5. Install Tooling (A) (not shown) in seal carrier (5). Remove seal carrier (5) and the three ring
seals from the transmission case assembly bore (7).
6. Repeat Step 4 through Step 5 on the three remaining seal carriers (5).
3/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g00623108
7. Remove seal rings (9) from seal carrier (5).
8. Remove three or four seals (8) from seal carrier (5).
9. Remove spring pin (10) from seal carrier (5).
10. Repeat Step 7 and Step 9 for the remaining three seal carriers (5).
Illustration 4 g00623110
11. Install Tooling (B) in the transmission case assembly (3). Tighten Tooling (B) evenly to
separate transmission case assembly (3) from transmission cover assembly (11).
12. Attach Tooling (A) to transmission case assembly (3). Position a lifting device to Tooling
(A). Secure the lifting device to a hoist. Slowly raise the transmission case assembly (3)
from the transmission cover assembly (11). Be careful not to bind the transmission case
assembly (3) during separation.
4/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g00623113
13. Remove three bolts (12) from tube assembly (13). Remove tube assembly (13) from the
transmission cover assembly (11).
14. Remove the O-ring seal from tube assembly (13).
Illustration 6 g00849491
Note: First/Third shaft assembly (14) and High/Low shaft assembly (15) must be removed
together.
15. Install Tooling (D) on First/Third shaft assembly (14) and High/Low shaft assembly (15).
Use Tooling (C) and Tooling (E) in order to hold Tooling (D) on First/Third shaft assembly
(14) and High/Low shaft assembly (15), as shown. First/Third shaft assembly (14) and
High/Low shaft assembly (15) must be removed together.
16. Attach a suitable lifting device to Tooling (D). Carefully remove First/Third shaft assembly
(14) and High/Low shaft assembly (15) from the transmission cover assembly (11). The
weight of the two shaft assemblies is 177 kg (390 lb).
5/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 7 g00623117
17. Place First/Third shaft assembly (14) and High/Low shaft assembly (15) on Tooling (F) or
on blocks and remove Tooling (D). Carefully separate First/Third shaft assembly (14) and
High/Low shaft assembly (15). The weight of each shaft assembly is 89 kg (195 lb).
Illustration 8 g00623120
Illustration 9 g00849492
Note: Place High/Low shaft (15) in a modified work bench or on blocks. Modify a
substantial workbench by cutting a 116.0 ± 2.0 mm (4.60 ± 0.08 inch) clearance hole in the
top of the bench.
6/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 10 g00623124
Illustration 11 g00623126
Note: Do not attach Tooling (G) to rotor (17). If pressure is applied to rotor (17) with
Tooling (G), rotor (17) will brake. Attach the Tooling (G) to gear assembly (18).
18. With High/Low shaft assembly (15) on the modified work bench or on blocks, use Tooling
(G) in order to remove race and bearing (16), rotor (17), gear assembly (18), and two sleeve
bearings (not shown) from High/Low shaft assembly (15). Press fit Bearing (16) and rotor
(17) on High/Low shaft assembly (15).
19. Remove bearing (16), rotor (17), thrust disc (19), and gear assembly (18) from High/Low
shaft assembly (15). Attach Tooling (G) to gear assembly (18). Do not attach Tooling (G) to
rotor (17).
7/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 12 g00623129
20. Remove thrust disc (20) and the washer from High/Low shaft assembly (15).
Illustration 13 g00623131
21. Install Tooling (H) and Tooling (K) on High/Low shaft assembly (15) and clutch assembly
(21). Tighten Tool (J) on Tooling (H) (not shown) in order to compress clutch assembly
(21). Remove two half rings (22) and two lock rings (23) from the High/Low shaft assembly
(15).
22. Carefully loosen Tool (J) on Tooling (H) in order to relieve pressure from clutch assembly
(21). Remove Tooling (K) and Tooling (H) from High/Low shaft assembly (15) and clutch
assembly (21). The clutch assembly (21) is made up of five clutch plates, six friction discs,
and the hub assembly. Identify the position of the clutch assembly (21) for assembly
purposes.
Illustration 14 g00623132
23. Remove wave spring (25) from High/Low shaft assembly (15).
24. Remove piston (24) from High/Low shaft assembly (15).
8/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 15 g00623134
25. Remove seal extension ring (27) and seal ring (26) from piston (22).
Illustration 16 g00623138
26. Position High/Low shaft assembly (15), as shown. Place High/Low shaft (15) in the
modified work bench, or on blocks. The weight of High/Low shaft assembly (15) is 50 kg
(110 lb).
27. Install Tooling (L) and Tooling (M) on High/Low shaft assembly (15) and inner bearing
(28). Remove inner bearing (28) from High/Low shaft assembly (15). Remove two thrust
discs (29), two bearing sleeves, and gear assembly (30) from High/Low shaft assembly (15).
Illustration 17 g00623141
9/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 28. Remove thrust disc (31) and the washer from High/Low shaft assembly (15).
Illustration 18 g00623145
Note: Tooling (K) is the old style tool that is now modified. Tooling (K) (new style tool)
works without being modified. Tooling (K) may need to be modified so the hole in the top
of the tube will have clearance for Tooling (N).
29. Install Tooling (N) and Tooling (K) on High/Low shaft assembly (15) and clutch assembly
(32). Tighten Tooling (P) on Tooling (N) in order to compress clutch assembly (32).
Remove two half rings (33) and two lock rings (34) from the High/Low shaft assembly (15).
30. Carefully loosen Tooling (P) on Tooling (N) in order to relieve pressure from clutch
assembly (32). Remove Tooling (K) and Tooling (N) from High/Low shaft assembly (15)
and clutch assembly (32). The clutch assembly (32) is made up of eight clutch plates, seven
friction discs, and the hub assembly. Identify the position of the clutch assembly (32) for
assembly purposes.
Illustration 19 g00623148
Note: Tooling (K) is the old style tool that must be modified. Tooling (K) (new style tool)
works without being modified. Tooling (K) may need to be modified so the hole in the top
of the tube will have clearance for Tooling (N).
31. Install Tooling (N) and Tooling (K) on High/Low shaft assembly (15) and balance piston
(35). Tighten Tooling (P) on Tooling (N) in order to compress balance piston (35).
10/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 32. Use Tooling (Q) in order to remove retaining ring (36) from High/Low shaft assembly (15).
33. Carefully loosen Tooling (P) on Tooling (N) in order to relieve pressure from balance piston
(35). Remove Tooling (K) and Tooling (N) in order to relieve pressure from High/Low shaft
assembly (15) and balance piston (35).
Illustration 20 g00623149
34. Remove balance piston (35) and seal extension ring (37) from High/Low shaft assembly
(15).
35. Remove 15 springs (38) from piston (39).
36. Remove piston (39), the seal extension ring (not shown), and a ring seal (not shown) from
High/Low shaft assembly (15).
Illustration 21 g00623150
37. Remove seal ring (40) and seal extension ring (41) from piston (39).
11/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 22 g00623152
38. Place First/Third shaft assembly (14) on the modified work bench or on blocks. Use Tooling
(F) in order to remove race and bearing (42), thrust disc (not shown), and gear assembly
(43) from First/Third shaft assembly (14).
Illustration 23 g00623154
39. Remove thrust disc (44) and gear assembly (45) from First/Third shaft assembly (14).
Illustration 24 g00623240
40. Remove sleeve bearing (not shown), thrust disc (46) and washer (47) from First/Third shaft
assembly (14).
12/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 25 g00623241
41. Install Tooling (H) and Tooling (K) on First/Third shaft assembly (14) and clutch assembly
(48). Tighten Tooling (K) on Tooling (H) in order to compress clutch assembly (48).
Remove two half rings (49) and two lock rings (50) from First/Third shaft assembly (14).
42. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch
assembly (48). Remove Tooling (K) and Tooling (H) from First/Third shaft assembly (14)
and clutch assembly (48). As you remove clutch assembly (48) from First/Third shaft
assembly (14), identify the positions of the five clutch plates, the six friction disc, and the
hub assembly for assembly purposes.
Illustration 26 g00623242
43. Remove wave spring (51) from First/Third shaft assembly (14).
44. Remove piston (52) from First/Third shaft assembly (14).
13/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 27 g00623245
45. Remove seal extension ring (53) and seal ring (54) from piston (52).
Illustration 28 g00623247
46. Position First/Third shaft assembly (14), as shown. Place First/Third shaft assembly (14) in
the modified work bench, or on blocks. The weight of First/Third shaft assembly (14) is
55 kg (120 lb).
47. Remove the seal ring (not shown) from First/Third shaft assembly (14).
48. Use Tooling (R) in order to remove inner bearing (55), thrust disc (not shown), gear (56),
and thrust disc (not shown).
49. Remove gear assembly (57), the bearing sleeve (not shown), the thrust disc, and the washer
(not shown) from First/Third shaft assembly (14).
14/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 29 g00623248
50. Install Tooling (K) and Tooling (H) on First/Third shaft assembly (14) and clutch assembly
(58). Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly (58).
Remove two half rings (59) and two lock rings (60) from the First/Third shaft assembly
(14).
51. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch
assembly (58). Remove Tooling (H) and Tooling (K) from First/Third shaft assembly (14)
and clutch assembly (58). As you remove clutch assembly (58) from First/Third shaft
assembly (14), identify the position of the three clutch plates, four friction disc, and the hub
assembly for assembly purposes.
Illustration 30 g00623249
52. Remove wave spring (61) from First/Third shaft assembly (14).
53. Remove piston (62) from First/Third shaft assembly (14).
15/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 31 g00623250
54. Remove seal extension ring (63) and seal ring (64) from piston (62).
Illustration 32 g00623252
Illustration 33 g00623253
55. Use Tooling (R) in order to remove inner bearing (66) and gear (67) from input shaft
assembly (65). This is necessary at this time in order to remove the remaining two shaft
assemblies.
16/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 34 g01024451
56. Install Tooling (S) and remove Reverse/Second shaft assembly (68) from the transmission
cover assembly (11). The weight of Reverse/Second shaft assembly (68) is 64 kg (140 lb).
Illustration 35 g00623257
57. Place Reverse/Second shaft assembly (68) on the modified work bench, or on blocks.
58. Use Tooling (R) in order to remove race and bearing (69), spacer (70), and gear (71) from
Reverse/Second shaft assembly (68).
Illustration 36 g00623258
17/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 59. Remove spacer (72) and thrust disc (not shown) from Reverse/Second shaft assembly (68).
60. Remove gear assembly (73), the sleeve bearing (not shown), the thrust disc (not shown),
and the washer (not shown) from Reverse/Second shaft assembly (68).
Illustration 37 g00623259
61. Install Tooling (K) and Tooling (H) on Reverse/Second shaft assembly (68) and clutch
assembly (74). Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly
(74). Remove two half rings (75) and two lock rings (76) from Reverse/Second shaft
assembly (68).
62. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch
assembly (74). Remove Tooling (H) and Tooling (K) from Reverse/Second shaft assembly
(68) and clutch assembly (74). As you remove clutch assembly (74) from Reverse/Second
shaft assembly (68), identify the positions of the three clutch plates, four friction disc and
the hub assembly for assembly purposes.
Illustration 38 g00623260
63. Remove wave spring (77) from Reverse/Second shaft assembly (68).
64. Remove piston (78) from Reverse/Second shaft assembly (68).
18/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 39 g00623261
65. Remove seal ring (80) and seal extension ring (79) from piston (78).
Illustration 40 g00623263
66. Position Reverse/Second shaft assembly (68), as shown. The weight of Reverse/Second
shaft assembly (68) is 41 kg (90 lb).
67. Place Reverse/Second shaft assembly (68) on the modified work bench, or on blocks.
68. Install Tooling (L) and Tooling (M) on gear assembly (82) and Reverse/Second shaft
assembly (68).
69. Remove inner bearing (81), the thrust race (not shown), the two thrust discs (not shown),
and gear assembly (82) from Reverse/Second shaft assembly (68).
19/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 41 g00623264
70. Remove roller bearing (83) from Reverse/Second shaft assembly (68).
71. Remove thrust disc and washer (84) from Reverse/Second shaft assembly (68).
Illustration 42 g00623265
72. Use a second person in order to compress clutch assembly (85).
73. Remove two half rings (86) from Reverse/Second shaft assembly (68). Release the pressure
from clutch assembly (85) slowly, until the spring (89) underneath clutch assembly (85) is
extended and relaxed.
Illustration 43 g00623269
20/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 74. Remove hub assembly (87) from Reverse/Second shaft assembly (68).
75. Remove spring (89) from Reverse/Second shaft assembly (68).
76. As you remove clutch plates (88) and friction discs (90), identify the locations of clutch
plates (88) and friction discs (90) for installation purposes. Remove six clutch plates (88)
and seven friction disc (90) from Reverse/Second shaft assembly (68).
Illustration 44 g00623270
77. Remove valve assembly (91) from Reverse/Second shaft assembly (68).
78. Remove piston (92) from Reverse/Second shaft assembly (68).
Illustration 45 g00623276
79. Remove seal ring (93) and (94) from piston (92).
80. Remove the cup plug (not shown) from Reverse/Second shaft assembly (68).
21/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 46 g01024454
81. Install Tooling (S) in Forward shaft assembly (95). Remove Forward shaft assembly (95)
from the transmission cover assembly (11). The weight of Forward shaft assembly (95) is
64 kg (140 lb).
Illustration 47 g00623279
82. Place Forward shaft assembly (95) on the modified work bench, or on blocks. Install
Tooling (L) and Tooling (M) to Forward shaft assembly (95) and gear assembly (97).
83. Remove race and bearing (96), two thrust disc (not shown), and gear assembly (97) from
Forward shaft assembly (95).
Illustration 48 g00623280
22/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 84. Remove roller bearing (98) from Forward shaft assembly (95).
85. Remove the thrust disc and washer (99) from Forward shaft assembly (95).
Illustration 49 g00623281
86. Use a second person in order to compress clutch assembly (100).
87. Remove two half rings (101) from Forward shaft assembly (95). Release the pressure from
clutch assembly (100) slowly, until the spring (104) underneath clutch assembly (100) is
extended and relaxed.
Illustration 50 g00623284
88. Remove hub assembly (102) from Forward shaft assembly (95).
89. Remove spring (104) from Forward shaft assembly (95).
90. Remove six clutch plates (105) and seven friction disc (103) from Forward shaft assembly
(95). Identify the positions of the clutch plates (105) and friction discs (103) for assembly
purposes.
23/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 51 g00623285
91. Remove valve assembly (106) from Forward shaft assembly (55).
92. Remove piston (107) from Forward shaft assembly (95).
Illustration 52 g00623287
93. Remove two seal rings (108) from piston (107).
Illustration 53 g00623288
24/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 94. Position Forward shaft assembly (95), as shown. The weight of Forward shaft assembly (95)
is 43 kg (95 lb). Place Forward shaft assembly (95) in the modified work bench or on
blocks.
95. Install Tooling (L) and Tooling (M) to Forward shaft assembly (95) and gear assembly
(110).
96. Remove inner bearing (109), the thrust race (not shown), the two thrust disc (not shown),
and gear assembly (110) from Forward shaft assembly (95).
Illustration 54 g00623289
97. Remove roller bearing (111) from Forward shaft assembly (95).
98. Remove the thrust disc and washer (112) from Forward shaft assembly (95).
Illustration 55 g00623291
99. Use a second person in order to compress clutch assembly (113).
100. Remove two half rings (114) from Forward shaft assembly (95).
101. Release the pressure from clutch assembly (113) slowly, until the spring (116) underneath
clutch assembly (113) is extended and relaxed.
25/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 56 g00623292
102. Remove hub assembly (115) from Forward shaft assembly (95).
103. Remove spring (116) from Forward shaft assembly (95).
104. Remove six clutch plates (117) and seven friction discs (118) from Forward shaft assembly
(95). Identify the positions of the clutch plates (117) and friction disc (118) for assembly
purposes.
Illustration 57 g00623294
105. Remove valve assembly (119) from Forward shaft assembly (95).
106. Remove piston (120) from Forward shaft assembly (95).
26/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 58 g00623297
107. Remove two seal rings (121) from piston (120).
108. Remove the cup plug (not shown) from Forward shaft assembly (95).
Illustration 59 g01024466
109. Install Tooling (S) in Input shaft assembly (65). Remove Input shaft assembly (65) from the
transmission cover assembly (11). The weight of Input shaft assembly (65) is 23 kg (50 lb).
Illustration 60 g00623299
110. Remove two seal rings (122) from Input shaft assembly (65).
111. Remove inner bearing (123) and gear (124) from Input shaft assembly (65).
112. Remove the cup plug (not shown) from input shaft assembly (65).
27/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 61 g00623300
113. Remove four bolts (125) from gear assembly (126). Rotate gear assembly (126) in order to
locate the two bolts (not shown).
114. Remove gear assembly (126) from the transmission cover assembly (11).
Illustration 62 g00623301
115. Position gear assembly (126), as shown. Use Tooling (Q) to remove snap ring (129) from
gear assembly (126).
116. Position gear assembly (126) to the opposite side. In order to drive ball bearing (127) off
gear assembly (126), push a small driver through three small holes (not shown).
117. Remove ball bearing (127) from bearing retainer (128).
Note: This is a slip fit.
28/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 63 g00623302
118. Remove five bearing outer races (130) from the transmission cover assembly (11).
119. Repeat Step 118 for transmission case assembly (3).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jan 29 15:37:03 UTC+0800 2021
29/29
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12H MOTOR GRADER CBK
Configuration: 12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -RENR4108-16 Publication Date -01/06/2018 Date Updated -26/06/2018
i05303122
Transmission - Assemble
SMCS - 3002-016; 3030-016; 3159-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-9736 Link Bracket 1
B 154-6181 Forcing Screw 2
C 6V-5221 Bolt 1
D 4C-8156 Lifting Fixture 1
E 6V-3918 Bolt 1
F 4C-8157 Lifting Fixture 2
G 1U-6405 Three Jaw Puller 1
H 1U-6341 Threaded Rod 1
J 5P-7970 Nut 1
K 9U-7479 Compressing Tube 1
L 5B-0637 High Idle Nut 1
5F-7353 Washer 1
1B-4207 Full Nut 2
5F-7369 Puller Leg 2
3H-0465 Push-Puller Plate 2
1/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. 5F-7366 Forcing Screw 1
5P-4808 Cap 2
1U-9895 Crossblock 1
M
9S-9151 Block 2
1B-4206 Nut 4
8B-7552 Forcing Bolt 2
N 1U-6343 Threaded Rod 1
P 6V-8149 Nut 1
Q 2P-8312 Retaining Ring Pliers 1
R
1P-2326 Forcing Screw 1
1P-2325 Head 1
3H-0462 Bolt 4
8H-0709 Strap 4
5F-7373 Jaw 3
S 3E-3882 Eyebolt 1
T 6V-5765 Sealant 1
Note: Remove old anaerobic sealant from the bottom of the blind tapped holes in housing (11)
before assembling.
Illustration 1 g00623302
1. Lower the temperature of bearing outer races (130) . Install bearing outer races (130) to the
original locations in both transmission case assembly (3) (not shown) and the transmission
cover assembly (11) until bearing outer races (130) are seated.
2/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 2 g00623301
2. Install bearing retainer (128) on gear assembly (126) .
3. Heat ball bearing (127) to a maximum of 135 °C (275 °F). Install ball bearing (127) to the
original location on gear assembly (126) .
4. Use Tooling (Q) in order to install snap ring (129) to the original location on gear assembly
(126) .
Illustration 3 g00623300
5. Install gear assembly (126) to the original location in the transmission cover assembly (11) .
6. Install two bolts (not shown) on the gear assembly (126) .
7. Install four bolts (125) in the gear assembly (126) . Tighten bolts (125) to a torque of 28 ± 7
N·m (21 ± 5 lb ft).
3/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. Illustration 4 g00623299
8. Install the cup plug (not shown) in input shaft assembly (65) .
9. Install gear (124) on Input shaft assembly (65) .
10. Heat inner bearing (123) to a maximum of 135 °C (275 °F). Install inner bearing (123) on
Input shaft assembly (65) until inner bearing (123) is seated. Gear (124) should be tight on
input shaft assembly (65) .
11. Install two seal rings (122) to the original locations on Input shaft assembly (65) .
Illustration 5 g01024466
12. Install Tooling (S) to Input shaft assembly (65) . Use a hoist in order to position Input shaft
assembly (65) to the original location in the transmission case assembly (11) . Install Input
shaft assembly (65) in the transmission case assembly (11) . Remove Tooling (S) from Input
shaft assembly (65) .
4/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
35. Illustration 6 g00623297
Illustration 7 g00623294
13. Install seal rings (121) on piston (120) . Install both seal rings (121) with the sealing lips
facing toward the small diameter of piston (120) .
14. Place Forward shaft assembly (95) in the modified work bench or on blocks. Apply a light
coat of clean hydraulic oil on seal rings (121) . Install piston (120) at the original location on
Forward shaft assembly (95) . Slightly rotate piston (120) while the seal is being installed.
Ensure that the seal rings (121) are installed properly.
15. Install valve assembly (119) to the original location on Forward shaft assembly (95) .
5/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. Illustration 8 g00623292
16. Install six clutch plates (117) and seven friction discs (118) in the original order on hub
assembly (115) . The splines on hub assembly (115) must align with the splines on the
friction discs (118) .
17. Install spring (116) in the original location on Forward shaft assembly (95) .
18. As one unit, install hub assembly (115) , six clutch plates (117) and seven friction discs
(118) to the original location on Forward shaft assembly (95) .
Illustration 9 g00623291
19. Use a second person in order to manually compress clutch assembly (113) on spring (116) .
20. Install two half rings (114) in the Forward shaft assembly (95) .
6/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
37. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
38. Illustration 10 g00623665
21. Install the washer and thrust disc (112) to the original locations on Forward shaft assembly
(95) .
Illustration 11 g00623672
22. Install gear assembly (110) on Forward shaft assembly (95) and over clutch assembly
(113) . Align the spline teeth on the outer diameter of the clutch plates (117) with the splines
on the inside of gear assembly (110) . Ensure that gear assembly (110) is completely down
over the clutch assembly (113) .
7/35
12H Motor Grader CBK00001-UP (MACHINE) POWERED BY C-9 Engine(SEBP33...
2021/1/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...