The document provides instructions for disassembling the differential of a Caterpillar Cat 12G Motor Grader. Key steps include:
1. Removing nuts, locks and washers to separate the differential from the carrier.
2. Removing bolts, locks and the cap to lift the differential out of the carrier.
3. Removing bearing cones and cages from the differential hubs.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...fujskemdidk8u
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential for disassembly or repair.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual Instant D...hean57759707
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential for disassembly or repair.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...fujjsekmdm3ed
The document provides step-by-step instructions for removing and installing a differential from a Caterpillar Cat 12G motor grader. It involves removing over 30 components and reinstalling them in reverse order. Key steps include removing the differential nut and lock, removing housing components, and precisely adjusting the differential installation to achieve the proper gear clearance.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...hdjsjndndnd
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential for disassembly or repair.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...nkog14651119
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. Next it removes dowels, fastens a hoist, and lifts out the differential and cages. It then removes bearings and bolts to disassemble further.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...tingrm81805
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential and related parts from the motor grader transmission.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual Instant D...hean57759707
The document provides step-by-step instructions for disassembling and assembling the differential of a Caterpillar Cat 12G motor grader. To disassemble, the technician must first remove all O-rings and nuts securing the differential cap. They then remove the cap, dowels, cages and bearing cones. Finally, the bolts holding the hubs are removed to separate the differential components.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...tingrm81805
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G motor grader. It involves removing over 30 components of the differential including the carrier, gears, bearings, seals and housing. The reassembly process involves carefully heating and positioning over 30 components back into place, and using various tools to measure torque and clearance. Proper measurement of backlash and end play is critical to ensure correct differential assembly.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...fujskemdidk8u
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential for disassembly or repair.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual Instant D...hean57759707
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential for disassembly or repair.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...fujjsekmdm3ed
The document provides step-by-step instructions for removing and installing a differential from a Caterpillar Cat 12G motor grader. It involves removing over 30 components and reinstalling them in reverse order. Key steps include removing the differential nut and lock, removing housing components, and precisely adjusting the differential installation to achieve the proper gear clearance.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...hdjsjndndnd
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential for disassembly or repair.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...nkog14651119
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. Next it removes dowels, fastens a hoist, and lifts out the differential and cages. It then removes bearings and bolts to disassemble further.
Caterpillar Cat 12G Motor Grader (Prefix 61M) Service Repair Manual (61M12027...tingrm81805
The document provides instructions for removing a differential from a Caterpillar Cat 12G motor grader in 29 steps. It begins by removing the nuts, locks and washers holding the differential cap to the carrier, then removing the cap. It continues describing how to remove the differential unit, cages, bearings and bolts holding components together. The overall process removes the differential and related parts from the motor grader transmission.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual Instant D...hean57759707
The document provides step-by-step instructions for disassembling and assembling the differential of a Caterpillar Cat 12G motor grader. To disassemble, the technician must first remove all O-rings and nuts securing the differential cap. They then remove the cap, dowels, cages and bearing cones. Finally, the bolts holding the hubs are removed to separate the differential components.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...tingrm81805
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G motor grader. It involves removing over 30 components of the differential including the carrier, gears, bearings, seals and housing. The reassembly process involves carefully heating and positioning over 30 components back into place, and using various tools to measure torque and clearance. Proper measurement of backlash and end play is critical to ensure correct differential assembly.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...hdjsjndndnd
The document provides step-by-step instructions for disassembling and assembling the differential of a Caterpillar Cat 12G motor grader. To disassemble, the technician must remove the differential assembly, cages, bearing cones, bolts holding the hubs, and seals. Key steps include loosening the lock nut, removing the cap and dowels, lifting out the differential using straps, and using specialty tools to remove bearing cones.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...nkog14651119
The document provides step-by-step instructions for disassembling and assembling the differential of a Caterpillar Cat 12G motor grader. To disassemble, the technician must first remove all O-rings and nuts securing the differential cap. They then remove the cap, dowels, cages and bearing cones. Finally, they separate the differential hub from the bevel gear housing using bolts. The process is reversed for reassembly.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...fujskemdidk8u
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G motor grader. It involves removing over 30 individual components of the differential and related systems. Key steps include removing the differential from the carrier, disassembling internal gears and bearings, replacing worn parts, adjusting clearance and backlash, and reassembling the differential before reinstalling it in the carrier.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...fujjsekmdm3ed
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G motor grader. It involves removing over 30 components of the differential including the carrier, gears, bearings, seals and housing. The reassembly process involves carefully heating and positioning over 30 components back into place, and using various tools to measure torque and clearance. Proper measurement of backlash and end play is critical to ensure correct differential assembly.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual Instant D...hean57759707
The document provides step-by-step instructions for removing a differential from a Caterpillar Cat 12G motor grader. It begins by removing nuts, locks, washers and wires to separate the differential cap from the carrier. Next, dowels and cages are removed from the differential. A hoist is used to lift the 160 lb differential out of the carrier. Bearing cones and bolts holding the hubs are then removed to fully separate the differential. The process is described in 14 steps over 2 pages.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M02629...hdjsjndndnd
The document provides step-by-step instructions for removing a differential from a Caterpillar Cat 12G motor grader. It begins by removing nuts, locks, washers and wires to separate the differential cap from the carrier. Next, dowels and cages are removed from the differential. A hoist is used to lift the 160 lb differential out of the carrier. Bearing cones and bolts holding the hubs are then removed to fully separate the differential. The process is described in 14 steps over 2 pages.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M02629...tingrm81805
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G Motor Grader. The process involves removing over 20 components of the differential including the carrier, gears, bearings, seals and housing. Components are then cleaned, inspected, and reassembled in reverse order while precisely adjusting clearances and preloads.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...udfjjdfjkksekm
This document provides instructions for removing and assembling the differential on a 140G Motor Grader. It begins by describing how to remove the differential by taking off the cap, nuts, bolts, locks, and dowels. It then explains how to remove the cages, bearings, pinion, and other components. The assembly section provides steps for installing bearings at high temperatures, and adjusting clearances and end play to reassemble the differential. The summary is in 3 sentences or less.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...fjjsefkksemme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...fusoelskemfm
The document provides step-by-step instructions for removing and installing a differential on a 140G Motor Grader. It begins by listing 27 steps to remove the differential and concludes with 37 steps to reinstall it. Key components that must be removed include the carrier, housing, gears, discs, pinion, bearings and seals. Proper heating and installation of bearings is emphasized. Clearance measurements and torque specifications are provided to ensure correct assembly.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...yhhjjkfkseme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...ikfkksmem
The document provides step-by-step instructions for removing and installing a differential on a 140G Motor Grader. It begins by listing 27 steps to remove the differential and concludes with 37 steps to reinstall it. Key components that must be removed include the carrier, housing, gears, discs, pinion, bearings and seals. Proper heating and installation of bearings is emphasized. Clearance measurements and torque specifications are provided to ensure correct assembly.
Caterpillar Cat 120G MOTOR GRADER (Prefix 87V) Service Repair Manual Instant ...fijsekkdmdm2w
The document provides step-by-step instructions for disassembling and assembling the final drives of a 120G motor grader. It involves removing the axles, tandem housing, bearings, gears, and other components. Reassembly requires installing these components in reverse order and adjusting the bearings. The process is repeated for the other final drive.
Caterpillar Cat 120G MOTOR GRADER (Prefix 87V) Service Repair Manual Instant ...fujkskemdmdm4r
The document provides instructions for servicing the final drives and transmission oil filter base of a 120G motor grader. It describes in detail how to disassemble and reassemble the final drives, which involves removing several components including gears, shafts, housings and seals. It also provides steps to remove and install the transmission oil filter base, and to disassemble and reassemble it by replacing seals and valves. The overall document outlines the repair and maintenance process for power train components on a 120G motor grader.
This document provides disassembly and assembly instructions for the transmission of a D6R track-type tractor. It details removing and installing over 80 individual parts. Key steps include separating the transmission from the bevel gear, removing the planetary group and transmission cover, and disassembling the individual clutch housings, gears, shafts, and carriers. Proper inspection and cleaning of parts is noted.
This document provides instructions for disassembling and assembling the final drive of a D6R track-type tractor. The disassembly procedure involves using various tools to remove 19 different components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and includes precautions for installing seals and bearings correctly.
The document provides instructions for removing and installing final drives on a D6R track-type tractor. It describes:
1) Removing the final drives which involves draining oil, removing mounting bolts and hardware, and lifting the drive out.
2) Disassembling the final drives by removing planetary carriers, gears, shafts, seals, and other components.
3) Assembling the final drives by reversing the disassembly steps and ensuring proper installation of seals, gears, carriers, and mounting hardware.
4) Reinstalling the final drives by lifting them into place, inserting mounting bolts and hardware, and refilling with oil.
This document provides instructions for removing and disassembling a final drive from a D6R track-type tractor, as well as assembling a final drive. Key steps include using specialized tools to remove the final drive and axle, disassembling internal components like planetary gears and carriers, and precisely installing seals and bearings during assembly. Safety notices warn of risks like uncontrolled machine movement if brakes are ineffective during removal.
This document provides instructions for disassembling and assembling the torque divider of a D6R track-type tractor. It describes removing and installing over 30 different components of the torque divider. Key steps include using tools and hoists to remove large components like the torque divider housing weighing 145 kg, and precisely measuring clearances between components like the stator and turbine wheel to be between 1.76 to 1.94 mm. Reassembly involves installing bearings and seals, heating components, and torquing bolts to specified values.
This document provides instructions for disassembling and assembling the bevel and transfer gears of a D6R track-type tractor. It describes removing over 30 individual components in 26 steps, including the transmission gears, bearings, seals, and housings. Reassembly is outlined in 38 steps, with specifics on heating and installing bearings, applying sealant, adjusting end play and backlash using shims and gauges, and torquing bolts. The document is highly technical and aimed at mechanics performing gearbox maintenance and repairs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model 558. It details 25 steps for disassembly, removing components like gears, shafts, seals and housings. It notes cleaning and inspecting parts before assembly. The assembly section lists 13 steps to reinstall components in reverse order, applying compounds and ensuring cleanliness. Special tools are listed to aid in removal and installation of heavy components weighing up to 510kg. Safety precautions are provided to contain fluids and protect personnel.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...hdjsjndndnd
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and drivers. Safety notices are provided regarding contained fluids, spring force, and being struck by parts.
More Related Content
Similar to Caterpillar Cat 12G Motor Grader (Prefix 3WC) Service Repair Manual (3WC01067 and up).pdf
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...hdjsjndndnd
The document provides step-by-step instructions for disassembling and assembling the differential of a Caterpillar Cat 12G motor grader. To disassemble, the technician must remove the differential assembly, cages, bearing cones, bolts holding the hubs, and seals. Key steps include loosening the lock nut, removing the cap and dowels, lifting out the differential using straps, and using specialty tools to remove bearing cones.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...nkog14651119
The document provides step-by-step instructions for disassembling and assembling the differential of a Caterpillar Cat 12G motor grader. To disassemble, the technician must first remove all O-rings and nuts securing the differential cap. They then remove the cap, dowels, cages and bearing cones. Finally, they separate the differential hub from the bevel gear housing using bolts. The process is reversed for reassembly.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...fujskemdidk8u
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G motor grader. It involves removing over 30 individual components of the differential and related systems. Key steps include removing the differential from the carrier, disassembling internal gears and bearings, replacing worn parts, adjusting clearance and backlash, and reassembling the differential before reinstalling it in the carrier.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M07711...fujjsekmdm3ed
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G motor grader. It involves removing over 30 components of the differential including the carrier, gears, bearings, seals and housing. The reassembly process involves carefully heating and positioning over 30 components back into place, and using various tools to measure torque and clearance. Proper measurement of backlash and end play is critical to ensure correct differential assembly.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual Instant D...hean57759707
The document provides step-by-step instructions for removing a differential from a Caterpillar Cat 12G motor grader. It begins by removing nuts, locks, washers and wires to separate the differential cap from the carrier. Next, dowels and cages are removed from the differential. A hoist is used to lift the 160 lb differential out of the carrier. Bearing cones and bolts holding the hubs are then removed to fully separate the differential. The process is described in 14 steps over 2 pages.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M02629...hdjsjndndnd
The document provides step-by-step instructions for removing a differential from a Caterpillar Cat 12G motor grader. It begins by removing nuts, locks, washers and wires to separate the differential cap from the carrier. Next, dowels and cages are removed from the differential. A hoist is used to lift the 160 lb differential out of the carrier. Bearing cones and bolts holding the hubs are then removed to fully separate the differential. The process is described in 14 steps over 2 pages.
Caterpillar Cat 12G MOTOR GRADER (Prefix 61M) Service Repair Manual (61M02629...tingrm81805
This document provides step-by-step instructions for removing and repairing the differential on a Caterpillar Cat 12G Motor Grader. The process involves removing over 20 components of the differential including the carrier, gears, bearings, seals and housing. Components are then cleaned, inspected, and reassembled in reverse order while precisely adjusting clearances and preloads.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...udfjjdfjkksekm
This document provides instructions for removing and assembling the differential on a 140G Motor Grader. It begins by describing how to remove the differential by taking off the cap, nuts, bolts, locks, and dowels. It then explains how to remove the cages, bearings, pinion, and other components. The assembly section provides steps for installing bearings at high temperatures, and adjusting clearances and end play to reassemble the differential. The summary is in 3 sentences or less.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...fjjsefkksemme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...fusoelskemfm
The document provides step-by-step instructions for removing and installing a differential on a 140G Motor Grader. It begins by listing 27 steps to remove the differential and concludes with 37 steps to reinstall it. Key components that must be removed include the carrier, housing, gears, discs, pinion, bearings and seals. Proper heating and installation of bearings is emphasized. Clearance measurements and torque specifications are provided to ensure correct assembly.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...yhhjjkfkseme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...ikfkksmem
The document provides step-by-step instructions for removing and installing a differential on a 140G Motor Grader. It begins by listing 27 steps to remove the differential and concludes with 37 steps to reinstall it. Key components that must be removed include the carrier, housing, gears, discs, pinion, bearings and seals. Proper heating and installation of bearings is emphasized. Clearance measurements and torque specifications are provided to ensure correct assembly.
Caterpillar Cat 120G MOTOR GRADER (Prefix 87V) Service Repair Manual Instant ...fijsekkdmdm2w
The document provides step-by-step instructions for disassembling and assembling the final drives of a 120G motor grader. It involves removing the axles, tandem housing, bearings, gears, and other components. Reassembly requires installing these components in reverse order and adjusting the bearings. The process is repeated for the other final drive.
Caterpillar Cat 120G MOTOR GRADER (Prefix 87V) Service Repair Manual Instant ...fujkskemdmdm4r
The document provides instructions for servicing the final drives and transmission oil filter base of a 120G motor grader. It describes in detail how to disassemble and reassemble the final drives, which involves removing several components including gears, shafts, housings and seals. It also provides steps to remove and install the transmission oil filter base, and to disassemble and reassemble it by replacing seals and valves. The overall document outlines the repair and maintenance process for power train components on a 120G motor grader.
Similar to Caterpillar Cat 12G Motor Grader (Prefix 3WC) Service Repair Manual (3WC01067 and up).pdf (14)
This document provides disassembly and assembly instructions for the transmission of a D6R track-type tractor. It details removing and installing over 80 individual parts. Key steps include separating the transmission from the bevel gear, removing the planetary group and transmission cover, and disassembling the individual clutch housings, gears, shafts, and carriers. Proper inspection and cleaning of parts is noted.
This document provides instructions for disassembling and assembling the final drive of a D6R track-type tractor. The disassembly procedure involves using various tools to remove 19 different components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and includes precautions for installing seals and bearings correctly.
The document provides instructions for removing and installing final drives on a D6R track-type tractor. It describes:
1) Removing the final drives which involves draining oil, removing mounting bolts and hardware, and lifting the drive out.
2) Disassembling the final drives by removing planetary carriers, gears, shafts, seals, and other components.
3) Assembling the final drives by reversing the disassembly steps and ensuring proper installation of seals, gears, carriers, and mounting hardware.
4) Reinstalling the final drives by lifting them into place, inserting mounting bolts and hardware, and refilling with oil.
This document provides instructions for removing and disassembling a final drive from a D6R track-type tractor, as well as assembling a final drive. Key steps include using specialized tools to remove the final drive and axle, disassembling internal components like planetary gears and carriers, and precisely installing seals and bearings during assembly. Safety notices warn of risks like uncontrolled machine movement if brakes are ineffective during removal.
This document provides instructions for disassembling and assembling the torque divider of a D6R track-type tractor. It describes removing and installing over 30 different components of the torque divider. Key steps include using tools and hoists to remove large components like the torque divider housing weighing 145 kg, and precisely measuring clearances between components like the stator and turbine wheel to be between 1.76 to 1.94 mm. Reassembly involves installing bearings and seals, heating components, and torquing bolts to specified values.
This document provides instructions for disassembling and assembling the bevel and transfer gears of a D6R track-type tractor. It describes removing over 30 individual components in 26 steps, including the transmission gears, bearings, seals, and housings. Reassembly is outlined in 38 steps, with specifics on heating and installing bearings, applying sealant, adjusting end play and backlash using shims and gauges, and torquing bolts. The document is highly technical and aimed at mechanics performing gearbox maintenance and repairs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model 558. It details 25 steps for disassembly, removing components like gears, shafts, seals and housings. It notes cleaning and inspecting parts before assembly. The assembly section lists 13 steps to reinstall components in reverse order, applying compounds and ensuring cleanliness. Special tools are listed to aid in removal and installation of heavy components weighing up to 510kg. Safety precautions are provided to contain fluids and protect personnel.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...hdjsjndndnd
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and drivers. Safety notices are provided regarding contained fluids, spring force, and being struck by parts.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include:
1) Draining oil from the final drive and removing covers, axles, and bolts holding components in place.
2) Using lifting tools and hoists to remove heavy components like final drives weighing over 600 kg.
3) Inspecting seals and bearings during disassembly and applying clean oil during assembly.
4) Heating and pressing bearings and seals into place during reassembly and torquing bolts to specified values.
Caterpillar Cat 390D L Excavator (Prefix WBT) Service Repair Manual (WBT00001...hdjsjndndnd
This document provides disassembly and assembly instructions for the travel motor on a 390D L excavator. It describes 40 steps to disassemble the travel motor, removing components like the head, relief valves, pistons, springs, seals and bearings. It then describes 3 steps to begin reassembling the travel motor, starting with installing the lip seal, bearing and retaining ring. Detailed illustrations are provided for each step. Cleanliness and applying lubricant to parts are emphasized during disassembly and assembly.
Caterpillar Cat 385C L Excavator (Prefix KKK) Service Repair Manual (KKK00001...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix JDL) Service Repair Manual...hdjsjndndnd
The document provides instructions for disassembling and assembling the final drive of a D6R III track-type tractor. The disassembly procedure involves 19 steps to remove components such as the planetary carrier, gears, seals, and hub. The assembly procedure describes 15 steps including pressing components, installing seals and bearings at specified temperatures, and torquing bolts to the correct specifications. Proper cleaning, lubrication, and use of specialized tools are emphasized to correctly perform the processes.
The document provides instructions for disassembling and assembling the travel motor of a 385C Excavator. It lists 40 steps for disassembly, including removing the head, relief valves, spools, pistons, springs, port plate, and other internal components. It then lists 16 steps for reassembly, starting with installing internal seals and moving outward to reinstalling the piston, port plate, spools, and head. Precautions are provided regarding cleaning parts, applying oil, and ensuring proper alignment of components.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix HCD) Service Repair Manual...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive components of a Caterpillar D6R III track-type tractor. The disassembly process involves using various tools to remove 19 components including planetary gears, bearings, seals, and hubs. The assembly process similarly uses tools to reinstall the components in the reverse order, taking care to clean parts and apply oil, and heat or cool components as needed to ensure proper installation. Special installation procedures are specified for seals and bearings.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
This document provides instructions for disassembling the control valve for the attachment, bucket, boom, right travel, left travel, and stick systems of a 385B Excavator. It outlines 25 steps to disassemble the various components of the control valve, including removing covers, seals, valves, pistons, solenoids, manifolds, and other parts. Precautions are provided to watch out for spring forces and to keep components clean during disassembly. Tools required include pliers. The goal is to disassemble the control valve into its individual parts to allow for inspection and replacement of any worn components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix FDT) Service Repair Manual ...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly process involves using various tools to remove 19 different parts from the final drive assembly, including the planetary carrier, gears, seals, and hub. The assembly process describes 16 steps for reinstalling the parts in reverse order and includes safety notices and requirements for cleaning, lubricating, and heating components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BRJ) Service Repair Manual ...hdjsjndndnd
The document provides instructions for disassembling the transmission of a D6R II track-type tractor. It lists the required tools and gives step-by-step instructions to remove components such as tubes, valves, gears, housings, pistons, seals, and plates. Special care must be taken to keep parts like discs and plates organized according to their clutch assemblies. Dismantling involves using lifting devices and compression tools to handle heavy internal components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BLE) Service Repair Manual ...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly procedure involves using various tools to remove 19 parts from the final drive assembly, including the planetary carrier, gears, seals, and hub. The assembly procedure describes 16 steps for installing the parts in reverse order, noting the importance of cleanliness and applying oil during assembly. Torque specifications and heating instructions are provided for certain bolts and bearings.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BMK) Service Repair Manual ...hdjsjndndnd
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes in detail how to remove and install components such as the planetary carrier, hub, ring gear, and seals using the proper tools. Cleanliness is emphasized throughout the process to prevent dirt from entering parts. Proper bearing installation and torque specifications are also outlined to ensure correct assembly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. start by:
a) remove differential
1. Bend the lock away from nut (1) and loosen nut (1) with tool (A).
2/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Remove nut (1), lock (3) and washer (2).
3. Put the differential and the carrier in position as shown.
4. Remove wire (5) from the nuts on each side of the differential. Remove nuts (8).
5. Bend the locks away from bolts (6). Remove the bolts, the locks and locks (7) from the cap.
6. Remove cap (4) from the carrier.
7. Remove the dowel that holds the small cage in alignment with the cap.
8. Fasten a hoist and a strap to the differential (9) as shown. Lift the differential and remove it
from the carrier. Weight is 240 lb. (109 kg).
3/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 9. Remove the ring and seal (10) from the carrier.
10. Remove small cage (11) from the differential. Remove the nut and the bearing cup from the
cage.
11. Remove bearing (12) from housing (14) with tooling (B).
12. Remove bolts (13) and the washers that hold housing (14) to the clutch housing. Remove
housing (14). Remove the brass washer from the inner face of housing (14).
13. Remove gear (15) from the spider gears.
14. Remove spider (18) and the gears and washers from the clutch housing.
15. Remove brass washers (16) and gears (17) from the spider.
4/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 16. Remove the brass bearings from the gears with tooling (C).
17. Remove gear (19) from the housing.
18. Turn the bevel gear, clutch housing and the piston housing over.
19. Remove cage (20). Remove the nut, the bearing cup, the ring and the two seals from cage (20).
20. Remove bolts (21) and the washers that hold piston housing (22) to the bevel gear and the
clutch housing. Remove piston housing (22).
21. Remove bearing (23) from the piston housing with tooling (B).
22. Turn the piston housing over.
5/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 23. Remove brass washer (24) and piston (25) from the piston housing. Remove the two seals
from the piston.
24. Remove discs (26) and disc assemblies (27) from the clutch housing.
25. Remove the pressure disc from the housing.
26. Remove pinion (28) from the carrier with tooling (D).
27. Remove bearing cups (29) and (31) from the carrier with a punch and a hammer.
28. Remove seal (30) from the carrier.
6/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 29. Remove bearing (32) from the pinion with tooling (E).
Assemble Differential (Unlocking)
1. Heat bearing (2) in oil to a temperature of 275° F (135° C). Install bearing (2) on pinion (1).
2. Lower the temperature of the two bearing cups for the pinion. Install the bearing cups in
differential carrier (3).
7/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 3. Install the seal in the differential carrier. Install the seal with the lip toward the bevel gear. Put a
small amount of oil on the lip of the seal.
4. Put pinion (1) in position on a block as shown. Install tooling (A) on carrier (3) and fasten a
hoist to tooling (A). Lift the carrier and put it in position over pinion (1) so bearing (2) is in its seat
in the bearing cup.
5. Heat bearing (4) in oil to a temperature of 275° F (135° C).
6. Install bearing (4) on pinion (1). Make sure the bearing is in its seat in the bearing cup. Lift the
carrier and remove the block from under the pinion. Put the carrier on the floor. Remove tooling
(A) from the carrier.
7. Install the washer, the lock and nut (5) on the pinion. Do not tighten the nut.
8. Put two .250 in. (6.35 mm) dowels in the splines of the pinion. Put the dowels in position 180°
apart. Install tooling (B) over the pinion and the dowels.
9. Check the amount of torque needed to move the pinion without any preload on the pinion
bearings. Remove the torque wrench from tooling (B).
10. Install a ratchet on tooling (B).
8/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 11. Install tool (C) on nut (5). Tighten nut (5) with tool (C) while holding the pinion with the
ratchet. Tighten the nut enough to get a torque of 6 ± 4 lb. in. (6.9 ± 4.6 cm.kg) more than the
torque needed to turn the pinion when the bearings were not preloaded. Remove tooling (B) and
(C).
12. Put clutch housing (7) in position on the floor as shown. Put a block of wood 2 1/2in. (63.5
mm) high in the center of the housing. Put gear (6) in position on the block.
13. Put the pressure disc in position in clutch housing (7). Install the eight discs and the seven disc
assemblies in the housing starting with a disc.
NOTE: Put clean SAE 30 oil on the discs and disc assemblies (8) at installation.
14. Put the large brass washer on the face of gear (6). Make sure the hole in the washer is in
alignment with the dowel in the housing.
15. Install the seals on the outside and the inside of the piston. Install the seals so the lips are
toward the bottom of the bore for the piston in the piston housing. Put some clean SAE 30 oil on
the lips of the seals. Install the piston in housing (10).
16. Heat bearing (9) in oil to a temperature of 275° F (135° C). Install bearing (9) on the hub of
piston housing (10).
17. Put piston housing (10) and the bevel gear in position on clutch housing (7). Make sure the
holes in both housings and the bevel gear are in alignment.
9/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 18. Install three 5/8"-11 NC forged eyebolts (12) in piston housing (10). Install the bolts and the
washers that hold the piston housing to the bevel gear and the clutch housing. Put a bar in position
as shown in the eyebolts. Tighten bolts (11) to a torque of 185 ± 10 lb. ft. (25.6 ± 1.4 mkg).
19. Remove the bar and the eyebolts.
20. Turn the housings and the bevel gear over. Be careful that gear (6) does not fall out.
21. Install the brass bearings in spider gears (14) with tool (E) and an arbor press.
22. Install gears (14) and brass washers (16) on spider (15). Put the spider and the gears in position
on the clutch housing as shown.
NOTE: Make sure the notches in the brass washers are up.
23. Install gear (13) as shown on the spider gears. Install the large brass washer on the face of gear
(13). Make sure the hole in the washer is in alignment with the dowel in the housing.
24. Put housing (18) in position on the clutch housing. Tool (F) can be used to make sure the
notches in washers (16) are in alignment with the dowels in housing (18). Install bolts (19) the
washers. Tighten the bolts to a torque of 60 ± 5 lb. ft. (8.3 ± 0.7 mkg).
25. Heat bearing (17) in oil to a temperature of 275° F (135° C). Install bearing (17) on the hub of
housing (18).
10/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 26. Install the bearing cup and nut (22) in cage (20). Install ring (23) and the two seals on the cage.
27. Put the cage in position over the bearing.
28. Install the nut and the bearing cup in cage (21). Put cage (21) in position over the bearing.
29. Fasten a hoist and a strap to the differential. Put the differential in position on the carrier.
Install the ring and seal between the carrier and cage (20). Make sure the opening in the cage is in
alignment with the ring and seal.
30. Put cap (24) in position over the studs in the carrier. Install the dowel in cage (21). Make sure
the dowel is in alignment with the hole in cap (24).
31. Install nuts (26) that hold the cap to the carrier. Tighten the four nuts to a torque of 75 lb. ft.
(10.4 mkg).
32. Put the differential in position as shown. Put tooling (D) in position on the differential and
against a tooth on the bevel gear. Turn the bevel gear to measure the gear clearance (backlash)
between the pinion and the bevel gear.
33. Make an adjustment to nut (22) under the bevel gear with tool (C), while keeping nut (25)
finger tight against the top bearing, to get a gear clearance (backlash) of .008 ± .002 in. (0.20 ±
0.05 mm).
11/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 34. Loosen nut (25). Tighten the nut by hand to remove the end play. Tighten nut (25) 1 to 1 1/2
notches and measure the amount of change in dimension (X) with tooling (D). Dimension (X)
must change by .005 ± .002 in. (0.13 ± 0.05 mm).
35. Tighten nuts (26) to a torque of 280 ± 20 lb. ft. (38.8 ± 2.8 mkg). Turn the differential and
measure the gear clearance (backlash) again.
36. Put locks (27) in position on the cap. Install the locks and bolts that hold locks (27). Bend the
locks against the bolts. Install wires (28) through the studs and nuts on each side of the
differential.
37. Install all the O-ring seals on the differential.
end by:
a) install differential
12/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 11 23:20:53 UTC+0800 2021
13/13
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12G MOTOR GRADER 3WC
Configuration: 12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
12G, 130G & 140G MOTOR GRADER POWER TRAIN
Media Number -SENR7186-01 Publication Date -01/11/1989 Date Updated -24/02/2006
SENR71860015
Differential (Direct Drive)
SMCS - 3258-15; 3258-16
1/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Disassemble Differential (Direct Drive)
2/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. start by:
a) remove differential
1. Remove all the O-ring seals from the differential. Bend the lock away from nut (1) and remove
nut (1) with tool (A).
3/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Remove lock (2) and washer (3) from the shaft.
3. Put the differential in position with the bevel gear up as shown.
4. Remove wire (7) from each side of the differential. Remove nuts (6) that hold the cap to the
carrier.
5. Remove bolt (4) from each side of the differential.
6. Remove lock (5) from each side of the differential.
7. Remove cap (8) from the carrier.
8. Remove dowel (9) from each of the cages on the differential.
9. Fasten a hoist and a strap to the differential.
4/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 10. Remove differential (10). Weight is 160 lb. (73 kg).
11. Remove cages (11) and (12). Remove the nuts and the bearing cups from the cages.
13. Remove bearing cone (13) with tooling (B).
14. Turn the differential on its other end. Put it on blocks as shown. Remove bolts (14) and the
washers that hold the hub and the bevel gear to the other hub.
5/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 15. Install three 5/8"-11 NC forged eyebolts in hub (17) as shown. Fasten a hoist to eyebolts (15).
16. Remove hub (17) from the bevel gear. Remove the bevel gear from the other hub.
17. Remove bearing cone (16) from hub (17) with tooling (B).
18. Remove pinion (18) from the differential carrier with tooling (C).
19. Remove bearing cups (20) and (21) from the differential carrier.
20. Remove seal (19) from the differential carrier.
21. Remove bearing cone (22) from pinion (18) with tooling (D).
6/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Assemble Differential (Direct Drive)
1. Heat bearing (2) in oil to a temperature of 275° F (135° C). Install bearing (2) on pinion (1).
2. Lower the temperature of the two bearing cups for the pinion. Install the bearing cups in
differential carrier (3).
3. Install the seal in the differential carrier. Install the seal with the lip toward the bevel gear. Put a
small amount of oil on the lip of the seal.
4. Put pinion (1) in position on a block as shown. Install tooling (A) on carrier (3) and fasten a
hoist to tooling (A). Lift the carrier and put it in position over pinion (1) so bearing (2) is in its seat
in the bearing cup.
7/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 5. Heat bearing (4) in oil to a temperature of 275° F (135° C).
6. Install bearing (4) on pinion (1). Make sure the bearing is in its seat in the bearing cup. Lift the
carrier and remove the block from under the pinion. Put the carrier on the floor. Remove tooling
(A) from the carrier.
7. Install the washer, the lock and nut (5) on the pinion. Do not tighten the nut.
8. Put two .250 in. (6.35 mm) dowels in the splines of the pinion. Put the dowels in position 180°
apart. Install tooling (B) over the pinion and the dowels.
9. Check the amount of torque needed to move the pinion without any preload on the pinion
bearings. Remove the torque wrench from tooling (B).
10. Install a ratchet on tooling (B).
11. Install tool (C) on nut (5). Tighten nut (5) with tool (C) while holding the pinion with the
ratchet. Tighten the nut enough to get a torque of 6 ± 4 lb. in. (6.9 ± 4.6 cm.kg) more than the
torque needed to turn the pinion when the bearings were not preloaded. Remove tooling (B) and
(C).
8/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 12. Heat bearing (6) in oil to a temperature of 275° F (135° C).
13. Install bearing (6) on hub (7).
14. Heat bearing (9) in oil to a temperature of 275° F (135° C). Install the bearing on hub (10).
15. Put hub (7) in position on blocks with its bearing down. Put bevel gear (12) in position on hub
(7). Install three 5/8"-11 NC forged eyebolts in hub (10). Fasten a hoist to eyebolts (8). Put the hub
in position on the bevel gear. Remove the hoist.
16. Install bolts (11) and the washers that hold the hub and the bevel gear to hub (7). Tighten the
bolts to a torque of 185 ± 10 lb. ft. (25.6 ± 1.4 mkg).
17. Remove the eyebolts from the differential.
18. Install the bearing cups and nuts (13) in cages (14). Put the cages in position on the hubs.
19. Fasten a hoist and a strap to the differential.
20. Lift the differential and put it in position on the carrier. Remove the hoist and the strap.
NOTE: Make sure the holes in the cages are up.
9/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 21. Install dowels (16) in the cages.
22. Put cap (15) in position on the cages and the studs. Make sure the dowels in the cages are in
alignment with the holes in the cap.
23. Install nuts (17) that hold the cap to the carrier. Tighten the nuts to a torque of 75 lb. ft. (10.4
mkg).
24. Put the differential in position as shown. Put tooling (D) in position on the differential and
against a tooth on the bevel gear. Turn bevel gear (12) to measure the gear clearance (backlash)
between the pinion and the bevel gear.
10/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 25. Make an adjustment to the nut under the bevel gear with tool (C), while keeping nut (18)
finger tight against the top bearing, to get a gear clearance (backlash) of .008 + .004 - .003 in.
(0.20 + 0.10 - 0.08 mm).
26. Loosen nut (18). Tighten the nut by hand to remove the end play. Tighten nut (18) 1 1/2 to 2
notches and measure the amount of change in dimension (X) with tooling (D). Dimension (X)
must change by .005 ± .002 in. (0.13 ± 0.05 mm).
27. Tighten nuts (17) to a torque of 280 ± 20 lb. ft. (38.8 ± 2.8 mkg). Turn the differential and
measure the gear clearance (backlash) again.
28. Put locks (20) in position on the cap. Install the locks and bolts (19) that hold the locks. Bend
the locks against the bolts.
29. Install wires (21) on the studs on each side of the differential.
30. Install all the O-ring seals on the differential.
end by:
a) install differential
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 11 23:21:49 UTC+0800 2021
11/11
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12G MOTOR GRADER 3WC
Configuration: 12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
12G, 130G & 140G MOTOR GRADER POWER TRAIN
Media Number -SENR7186-01 Publication Date -01/11/1989 Date Updated -24/02/2006
SENR71860016
Transmission
SMCS - 3150-11; 3150-12; 3150-15; 3150-16; 3159-15; 3159-16
Remove Transmission
start by:
a) remove fuel tank
b) remove alternator
c) remove fan drive
d) remove transmission oil filter base
e) remove transmission oil and scavenge pump
f) remove parking brake rotochamber and release valve
1. Drain the oil from the transmission. Drain the coolant from the cooling system.
NOTE: The plug that has a location in tube (4) toward the front of the machine can be removed to
drain the coolant from tube (4). Put the plug in position in tube (4) after draining the coolant.
2. Remove hose clamps (1) from each end of tube (4). Remove tube (4).
1/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 3. Put identification on oil lines (3) as to their location on the relief control valve. Disconnect oil
lines (3) from the valve.
4. Loosen the nuts from bolts (2) on each side of the engine. Tighten bolts (2) until they are
against the frame. Tighten the nuts.
5. Remove bolts (6) and retainer (9) that hold couplings (8) to the transmission. Loosen nuts (7)
and slide couplings (8) free of the transmission. Lift control cables (5) out of the links on the
transmission control valves.
6. Fasten a hoist to the lifting eyes on the transmission. Remove bolts (10) that hold the
transmission to the flywheel housing. Remove nuts (11) that hold the transmission to the studs in
the differential housing.
7. Move the transmission away from the engine and off the studs in the differential housing.
8. Lift transmission (12) and remove it from the machine. Weight is 1500 lb. (680 kg).
Install Transmission
2/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 1. Fasten a hoist to the lifting eyes on the transmission. Lower the transmission (1) into position in
the machine.
2. Move the transmission on to the studs in the differential housing and into the flywheel housing.
NOTE: To put the splines on the transmission adapter in alignment with the flywheel, turn the
transmission oil pump shaft. To put the splines in the transmission in alignment with the splines
on the differential input shaft, the following procedure can be used:
a) Drain the oil from the tandem housings.
b) Remove the axles.
c) Turn the differential input shaft with a prybar or a screwdriver while the transmission is being
installed on the studs of the differential housing.
d) Install the axles and fill the tandem housings with oil to their correct levels.
3. Install bolts (2) that hold the transmission to the flywheel housing. Install the nuts that hold the
transmission to the differential housing. Connect oil lines (3) to their correct locations on the relief
control valve. Remove the hoist.
4. Put three control cables (7) in position on the valve links. Put couplings (6) in position in the
transmission housing. Tighten nuts (4) against the couplings. Put retainer (5) in position over the
couplings. Install the bolts that hold the retainer to the transmission housing.
3/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 5. Put tube (8) in position on the machine. Tighten hose clamps (9) at each end of tube (8) over the
tube. Loosen the nuts on bolts (10) on each side of the machine. Move bolts (10) away from the
frame. Tighten the nuts.
6. Fill the transmission with oil to its correct level. Fill the cooling system with coolant to its
correct level.
end by:
a) install parking brake rotochamber and release valve
b) install transmission oil and scavenge pump
c) install transmission oil filter base
d) install fan drive
e) install alternator
f) install fuel tank
Disassemble Transmission
start by:
4/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. a) remove transmission
1. Install the transmission on tooling (C). Remove bolts (1) and the lockwashers that hold the
cover to the transmission. Remove cover (2).
2. Remove links (3) from the transmission hydraulic control valves.
3. Remove bolts (8) and plates (7). Move the four sleeves (5) free of the transmission hydraulic
control valves.
NOTE: Do not remove bolts (4) and (6) at this time. Bolts (4) and (6) hold the control valves to
the transmission.
4. Install a 3/8"-16 NC forged eyebolt in the transmission case. Install tooling (B) in the eyebolt.
5/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. 5. Install tooling (A) on the transmission case and on the control valves. Connect tooling (B) to
tooling (A) as shown. Remove bolts (4) and (6). Remove transmission hydraulic control valves (9)
with tooling (B). Weight is 90 lb. (41 kg). See DISASSEMBLE HYDRAULIC CONTROL
VALVES for disassembly of the control valves.
6. Remove the four sleeves from the transmission. Fasten tooling (D) to the lifting eyes on top of
the transmission. Remove the bolts that hold the transmission to tooling (C). Remove the bolts and
cover (10).
7. Install two 1/2"-13 NC forged eyebolts and two nuts in the transmission on top of the output
flange. Fasten tooling (D) to the two eyebolts.
8. Turn the transmission on its end with tooling (D). Put the transmission in position on tooling
(E). Remove tooling (D) and the eyebolts.
9. Remove O-rings (11) and O-ring (12) from the housing.
10. Remove bolt (13) and bolt (14) that hold the planetary transmission in the transmission case.
11. Install two 5/8"-11 NC forged eyebolts (15) in the housing. Fasten a hoist to the eyebolts.
12. Remove the planetary transmission from the transmission case. Weight is 560 lb. (254 kg).
13. Put the transmission on three blocks.
6/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Make sure the input gear for the planetary transmission is on top of the
blocks. If the input gear is not on top of the blocks, other components
can fall out the bottom of the transmission when a retaining ring is
removed.
14. Remove bolts (16). Remove O-ring seal (18). Lift housing (17) enough to remove springs (19)
and plungers (20). Remove the housing. Weight is 85 lb. (39 kg). Remove the O-ring seal that is
under the flange on housing (17).
15. Remove bolts (22). Bend the locks (23) away from bolts (21). Remove bolts (21) and locks
(23).
16. Remove hub (25). Remove four discs (24) and three plates (26). These discs and plates are for
the parking brake clutch.
7/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. 17. Install tooling (F) as shown against plate (29). Put springs (28) in compression with tooling (F)
and a press.
18. Remove retaining ring (27). Slowly release the compression on springs (28). Remove tooling
(F). Remove the plate and the springs.
19. Remove cage (30) from the hub. Remove O-ring seal (31) and the internal ring that is under
the O-ring seal.
20. Remove external ring (32) from the hub.
21. Remove piston (34).
22. Remove ring gear (33).
8/41
12G Motor Grader 3WC01067-UP (MACHINE) POWERED BY 3306 Engine(SEBP1...
2021/2/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...