This document provides instructions for disassembling and assembling the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 48 steps to completely disassemble these components, noting any weights, quantities, or order of parts that should be recorded. Tools required are also listed. Reassembly is presumably the reverse of the disassembly steps.
Caterpillar cat 120 m series 2 motor grader (prefix r9n) service repair manua...fjsjjekdkme
This document provides instructions for disassembling the transmission of a 120M Series 2 Motor Grader. It lists over 40 individual steps and provides illustrations for each step. The transmission must be removed from the grader and various components disassembled, including housing components, gears, seals, plates, and sensors. Special tools are required and spring forces must be released safely. The process involves removing over 50 individual parts in a specific sequence.
Caterpillar cat 120 m motor grader (prefix r9a) service repair manual (r9a000...fjsjjekdkme
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M motor grader. It describes 46 separate steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Various tools are required, and notes are provided about part ordering and weights of components being removed. The goal is to break down these drivetrain components into their smallest indivisible parts for repair or replacement.
Claas nectis f 227 2+4 wd (type t16) tractor service repair manualfjsjjekdkme
This document provides specifications for Iveco "NEF" diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication and cooling systems, dimensions of components like pistons and cylinders, and torque specifications. The document stresses that performance data is only valid if installation recommendations are followed.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualfjsjjekdkme
The document contains parts lists and diagrams for various components of a Massey Ferguson MF 265 tractor, including the cylinder block, cylinder head, crankshaft, timing gear, and other systems. It lists 46 individual parts that make up the timing gear assembly, providing part numbers, quantities, descriptions, and comments for each item. Reference numbers and page numbers are included throughout.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00001 ...fjsjjekdkme
This document provides disassembly instructions for the 312C and 312C L excavator final drive, travel motor, and travel counterbalance valve systems. It outlines 17 steps to disassemble the final drive which includes removing covers, plates, gears, and bearings. It also details 13 steps to disassemble the travel motor such as removing piston assemblies, seals, and barrel components. Finally, it lists 15 steps for disassembling the travel counterbalance valve including removing springs, spools, valves, and housings. Personal safety notices are included throughout regarding releasing pressures and contained parts.
Massey ferguson mf 362 n tractor (japan only) parts catalogue manualfjsjjekdkme
This document provides specifications for a Massey Ferguson MF 362 N tractor intended for the Japanese market only. It includes detailed parts lists and descriptions for the engine, cylinder block, crankshaft, pistons, cylinder head, and other components. Reference part numbers are given for each item along with other identifying information.
Claas nectis ve 217 2+4 wd (type t14) tractor service repair manualfjsjjekdkme
1) The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications.
2) It describes the components and operating principles of the fuel injection system, including the fuel tank, lines, filters, pump, and injectors. Diagrams show the components and flow of fuel.
3) Instructions are provided for checking and adjusting aspects of the system, such as setting the accelerator control cable and adjusting the internal timing of the injector pump. Torque specifications are also listed.
Claas celtis 456 426 ra (type a07) tractor service repair manualfjsjjekdkme
This document provides technical specifications and inspection procedures for engine components including the cylinder head, valves, turbocharger, and head gasket of a Celtis engine. It includes dimensions, diagrams, and step-by-step checks to identify potential issues such as coolant or gas leaks between the cylinder head and engine block. Symptoms and causes of combustion gas and coolant sealing failures are outlined to guide troubleshooting and repair.
Caterpillar cat 120 m series 2 motor grader (prefix r9n) service repair manua...fjsjjekdkme
This document provides instructions for disassembling the transmission of a 120M Series 2 Motor Grader. It lists over 40 individual steps and provides illustrations for each step. The transmission must be removed from the grader and various components disassembled, including housing components, gears, seals, plates, and sensors. Special tools are required and spring forces must be released safely. The process involves removing over 50 individual parts in a specific sequence.
Caterpillar cat 120 m motor grader (prefix r9a) service repair manual (r9a000...fjsjjekdkme
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M motor grader. It describes 46 separate steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Various tools are required, and notes are provided about part ordering and weights of components being removed. The goal is to break down these drivetrain components into their smallest indivisible parts for repair or replacement.
Claas nectis f 227 2+4 wd (type t16) tractor service repair manualfjsjjekdkme
This document provides specifications for Iveco "NEF" diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication and cooling systems, dimensions of components like pistons and cylinders, and torque specifications. The document stresses that performance data is only valid if installation recommendations are followed.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualfjsjjekdkme
The document contains parts lists and diagrams for various components of a Massey Ferguson MF 265 tractor, including the cylinder block, cylinder head, crankshaft, timing gear, and other systems. It lists 46 individual parts that make up the timing gear assembly, providing part numbers, quantities, descriptions, and comments for each item. Reference numbers and page numbers are included throughout.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00001 ...fjsjjekdkme
This document provides disassembly instructions for the 312C and 312C L excavator final drive, travel motor, and travel counterbalance valve systems. It outlines 17 steps to disassemble the final drive which includes removing covers, plates, gears, and bearings. It also details 13 steps to disassemble the travel motor such as removing piston assemblies, seals, and barrel components. Finally, it lists 15 steps for disassembling the travel counterbalance valve including removing springs, spools, valves, and housings. Personal safety notices are included throughout regarding releasing pressures and contained parts.
Massey ferguson mf 362 n tractor (japan only) parts catalogue manualfjsjjekdkme
This document provides specifications for a Massey Ferguson MF 362 N tractor intended for the Japanese market only. It includes detailed parts lists and descriptions for the engine, cylinder block, crankshaft, pistons, cylinder head, and other components. Reference part numbers are given for each item along with other identifying information.
Claas nectis ve 217 2+4 wd (type t14) tractor service repair manualfjsjjekdkme
1) The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications.
2) It describes the components and operating principles of the fuel injection system, including the fuel tank, lines, filters, pump, and injectors. Diagrams show the components and flow of fuel.
3) Instructions are provided for checking and adjusting aspects of the system, such as setting the accelerator control cable and adjusting the internal timing of the injector pump. Torque specifications are also listed.
Claas celtis 456 426 ra (type a07) tractor service repair manualfjsjjekdkme
This document provides technical specifications and inspection procedures for engine components including the cylinder head, valves, turbocharger, and head gasket of a Celtis engine. It includes dimensions, diagrams, and step-by-step checks to identify potential issues such as coolant or gas leaks between the cylinder head and engine block. Symptoms and causes of combustion gas and coolant sealing failures are outlined to guide troubleshooting and repair.
Massey ferguson mf 375 tractor, b18008 parts catalogue manualfjsjjekdkme
The document provides parts information for the engine of a Massey Ferguson MF 375 tractor, including the engine block, crankshaft, pistons, cylinder head, and other components. It lists 33 individual parts by number, quantity, part number, description, and other identifying information. Notes are provided to indicate application and replacement part numbers for some items. The list repeats over multiple pages and sections in a consistent tabular format.
This document provides specifications and dimensions for "NEF" diesel engines, including 3 and 4 cylinder models. It describes the engine systems such as lubrication, cooling, turbocharging, and dimensions of components. The lubrication system uses a lobe oil pump to circulate oil through the crankshaft, camshaft, cylinder head and oil cooler. The cooling system has a radiator, visco-static fan, water pump, thermostat and oil cooler. Turbocharged models include an air filter and exhaust-driven turbocharger. Detailed dimensions are provided for build clearances, engine block components, cylinder head and valves. Torque specifications are also listed.
Caterpillar cat 301.4 c mini hydraulic excavator (prefix ljk) service repair ...fjsjjekdkme
This document provides instructions for removing and installing fuel injection lines, the fuel injection pump, and fuel injectors on a 301.4C Mini Hydraulic Excavator. The procedures involve disconnecting lines and removing nuts, taking identification marks for installation purposes, and reinstalling components in reverse order while following torque specifications. Tools required include line wrenches, pullers, and thread locking compound. Safety notices emphasize containing fluids and properly disposing of them.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Massey ferguson mf 24 combine parts catalogue manualfjsjjekdkme
The document provides a parts list and technical specifications for a Massey Ferguson MF 24 combine harvester with the serial number 819723. It includes over 50 numbered items with corresponding part numbers, quantities, descriptions, and additional comments. The parts are grouped into sections covering the straw divider, knives and fingers, wearing plates and stone stops, counter shaft, guarding, and feeder drum.
Massey ferguson mf 1260 compact tractor ( e60101 - hst non hst) parts catal...fjskekmdm
This document provides parts information for a Massey Ferguson 1260 compact tractor, including 61 items that make up the timing gear housing component. It lists the part number, quantity, description, and any additional comments for each item. The parts include gaskets, bolts, seals, pins, plates, shafts, bearings, and other components of the timing gear housing. Serial or engine numbers are specified for some parts to indicate when a part number changed.
Hyundai hbf18 t 5 forklift truck service repair manualfjjsekmmm
This document provides instructions for disassembling and assembling the steering unit of a machine. It includes the following sections:
1. Tools and torque specifications needed for the job.
2. Instructions for disassembling components like the end cover, gearwheel set, cardan shaft, distributor plate, seals and springs.
3. Instructions for assembling components like the spool, sleeve, seals, springs and end cover. Precise steps are provided to ensure correct assembly.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a 3054C engine. The flywheel removal process involves using guide bolts and a link bracket to support the flywheel weight during removal. The crankshaft rear seal housing is non-serviceable and must be replaced if removed. A plastic sleeve is used to protect the crankshaft rear seal during installation. A puller tool is used to remove the crankshaft wear sleeve.
Caterpillar cat 966 h wheel loader (prefix a6d) service repair manual (a6d000...ufjjsjefkksemm
This document provides instructions for disassembling and assembling the piston pump of a 966H wheel loader. The disassembly process involves 28 steps to remove components like valves, spools, plugs, springs, and pistons. The assembly process reverses the disassembly with 23 steps and cautions that improper assembly of spring-loaded parts can cause injury. Tools including retaining ring pliers and a compression plate are required. Torque specifications are provided for reinstalling bolts.
Caterpillar cat 301.7 d mini hydraulic excavator (prefix lj4) service repair ...ufjjsjefkksemm
This document provides instructions for removing and installing various components of a 301.7D Mini Hydraulic Excavator, including the engine, flywheel, hydraulic cylinders, blade, and bucket. It includes detailed removal and installation steps, specifications, torque values, and safety warnings for each component. Illustrations are provided to supplement the text instructions.
Jcb ps760 transmission service repair manualufjjsjefkksemm
This service manual section provides information on servicing and repairing components of the JCB PS760, PS764, PS766 semi-automatic gearbox. The document covers general information, as well as procedures for clutches, solenoid valves, oil pumps, shafts, cases, and other components. Torque specifications and part numbers are included for repairs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
Massey ferguson mf 24 combine engines (perkins) parts catalogue manualfjsjjekdkme
This document provides parts information for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine engines with Perkins engines. It includes detailed parts lists, part numbers, quantities and descriptions for the engine cylinder block, crankshaft, pistons, connecting rods, cylinder head and other engine components. The parts lists reference exploded diagrams of the engine systems and components.
Caterpillar cat 120 m series 2 motor grader (prefix m9h) service repair manua...fjsjjekdkme
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 42 steps to fully disassemble these components, including removing gears, bearings, seals, housings, and other parts. Special tools are required and weights of parts are provided. Safety notices are included and parts must be kept clean to prevent contamination.
Caterpillar cat 120 m series 2 motor grader (prefix m9h) service repair manua...fjsekkdmmmse
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 42 steps to fully disassemble these components, including removing gears, bearings, seals, housings, and other parts. Special tools are required and weights of parts are provided. Safety notices are included and parts must be kept clean to prevent contamination.
Caterpillar cat 140 m 2 motor grader (prefix m9j) service repair manual (m9j0...jfkseksmemqw
This document provides instructions to disassemble the rear axle, differential, and final drive of a 140M 2 motor grader. It lists 29 tools required and provides 42 detailed steps to remove components like the rear axle, sprockets, bearings, housing, carrier assembly, pinion gears, and differential gears. Detailed illustrations accompany each step to show how to position lifting devices and what fasteners to remove. Cautions are provided about cleaning parts and noting shim quantities and positions during disassembly.
Caterpillar cat 140 m 2 motor grader (prefix m9j) service repair manual (m9j0...fusjefjskekmem
The document provides disassembly instructions for the rear axle, differential, and final drive of a 140M 2 motor grader. It lists 29 required tools and provides 43 detailed steps to disassemble these components. These include removing housing components, gears, seals, bearings, and other parts. Weights and lifting precautions are noted for many components. Order and placement of shims and other parts must be recorded during disassembly.
Caterpillar cat 140 m 2 motor grader (prefix m9j) service repair manual (m9j0...fusejkskemfm
This document provides instructions to disassemble the rear axle, differential, and final drive of a 140M 2 motor grader. It lists 29 tools required and provides 42 detailed steps to remove components like the rear axle, sprockets, bearings, housing, carrier assembly, pinion gears, and differential gears. Detailed illustrations accompany each step to show how to position lifting devices and what fasteners to remove. Cautions are provided about cleaning parts and noting shim quantities and positions during disassembly.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...fijsekkdmdm2w
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Numerous specialized tools are required to properly disassemble the components. Technicians are instructed to note part quantities and orders during disassembly.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...zan2736ban
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Numerous specialized tools are required to properly disassemble the components. Technicians are instructed to note part quantities and orders during disassembly.
Caterpillar cat 120 m series 2 motor grader (prefix r9w) service repair manua...fjjsekdmmme
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Required tools include pullers, wrenches, bolts, and lifting devices to safely remove heavier components like housings and gears. Proper disassembly is important to inspect and replace worn parts.
Massey ferguson mf 375 tractor, b18008 parts catalogue manualfjsjjekdkme
The document provides parts information for the engine of a Massey Ferguson MF 375 tractor, including the engine block, crankshaft, pistons, cylinder head, and other components. It lists 33 individual parts by number, quantity, part number, description, and other identifying information. Notes are provided to indicate application and replacement part numbers for some items. The list repeats over multiple pages and sections in a consistent tabular format.
This document provides specifications and dimensions for "NEF" diesel engines, including 3 and 4 cylinder models. It describes the engine systems such as lubrication, cooling, turbocharging, and dimensions of components. The lubrication system uses a lobe oil pump to circulate oil through the crankshaft, camshaft, cylinder head and oil cooler. The cooling system has a radiator, visco-static fan, water pump, thermostat and oil cooler. Turbocharged models include an air filter and exhaust-driven turbocharger. Detailed dimensions are provided for build clearances, engine block components, cylinder head and valves. Torque specifications are also listed.
Caterpillar cat 301.4 c mini hydraulic excavator (prefix ljk) service repair ...fjsjjekdkme
This document provides instructions for removing and installing fuel injection lines, the fuel injection pump, and fuel injectors on a 301.4C Mini Hydraulic Excavator. The procedures involve disconnecting lines and removing nuts, taking identification marks for installation purposes, and reinstalling components in reverse order while following torque specifications. Tools required include line wrenches, pullers, and thread locking compound. Safety notices emphasize containing fluids and properly disposing of them.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00301 ...fjsjjekdkme
1. The document provides instructions for removing and installing the front housing of a 312C excavator engine.
2. To remove the front housing, several other components must first be removed, including the alternator, water pump, and crankshaft pulley. Bolts securing the front housing to other parts are then loosened and removed.
3. Installation involves cleaning surfaces, installing new seals if needed, and securing the front housing with bolts to the cylinder block, oil pan, and other parts. Timing gear alignment must also be checked during installation.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Massey ferguson mf 24 combine parts catalogue manualfjsjjekdkme
The document provides a parts list and technical specifications for a Massey Ferguson MF 24 combine harvester with the serial number 819723. It includes over 50 numbered items with corresponding part numbers, quantities, descriptions, and additional comments. The parts are grouped into sections covering the straw divider, knives and fingers, wearing plates and stone stops, counter shaft, guarding, and feeder drum.
Massey ferguson mf 1260 compact tractor ( e60101 - hst non hst) parts catal...fjskekmdm
This document provides parts information for a Massey Ferguson 1260 compact tractor, including 61 items that make up the timing gear housing component. It lists the part number, quantity, description, and any additional comments for each item. The parts include gaskets, bolts, seals, pins, plates, shafts, bearings, and other components of the timing gear housing. Serial or engine numbers are specified for some parts to indicate when a part number changed.
Hyundai hbf18 t 5 forklift truck service repair manualfjjsekmmm
This document provides instructions for disassembling and assembling the steering unit of a machine. It includes the following sections:
1. Tools and torque specifications needed for the job.
2. Instructions for disassembling components like the end cover, gearwheel set, cardan shaft, distributor plate, seals and springs.
3. Instructions for assembling components like the spool, sleeve, seals, springs and end cover. Precise steps are provided to ensure correct assembly.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a 3054C engine. The flywheel removal process involves using guide bolts and a link bracket to support the flywheel weight during removal. The crankshaft rear seal housing is non-serviceable and must be replaced if removed. A plastic sleeve is used to protect the crankshaft rear seal during installation. A puller tool is used to remove the crankshaft wear sleeve.
Caterpillar cat 966 h wheel loader (prefix a6d) service repair manual (a6d000...ufjjsjefkksemm
This document provides instructions for disassembling and assembling the piston pump of a 966H wheel loader. The disassembly process involves 28 steps to remove components like valves, spools, plugs, springs, and pistons. The assembly process reverses the disassembly with 23 steps and cautions that improper assembly of spring-loaded parts can cause injury. Tools including retaining ring pliers and a compression plate are required. Torque specifications are provided for reinstalling bolts.
Caterpillar cat 301.7 d mini hydraulic excavator (prefix lj4) service repair ...ufjjsjefkksemm
This document provides instructions for removing and installing various components of a 301.7D Mini Hydraulic Excavator, including the engine, flywheel, hydraulic cylinders, blade, and bucket. It includes detailed removal and installation steps, specifications, torque values, and safety warnings for each component. Illustrations are provided to supplement the text instructions.
Jcb ps760 transmission service repair manualufjjsjefkksemm
This service manual section provides information on servicing and repairing components of the JCB PS760, PS764, PS766 semi-automatic gearbox. The document covers general information, as well as procedures for clutches, solenoid valves, oil pumps, shafts, cases, and other components. Torque specifications and part numbers are included for repairs.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for disassembling each component. Personal safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs or releasing hydraulic pressure. The document is intended to guide technicians in properly disassembling these systems for repair or replacement of parts.
Massey ferguson mf 24 combine engines (perkins) parts catalogue manualfjsjjekdkme
This document provides parts information for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine engines with Perkins engines. It includes detailed parts lists, part numbers, quantities and descriptions for the engine cylinder block, crankshaft, pistons, connecting rods, cylinder head and other engine components. The parts lists reference exploded diagrams of the engine systems and components.
Caterpillar cat 120 m series 2 motor grader (prefix m9h) service repair manua...fjsjjekdkme
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 42 steps to fully disassemble these components, including removing gears, bearings, seals, housings, and other parts. Special tools are required and weights of parts are provided. Safety notices are included and parts must be kept clean to prevent contamination.
Caterpillar cat 120 m series 2 motor grader (prefix m9h) service repair manua...fjsekkdmmmse
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 42 steps to fully disassemble these components, including removing gears, bearings, seals, housings, and other parts. Special tools are required and weights of parts are provided. Safety notices are included and parts must be kept clean to prevent contamination.
Caterpillar cat 140 m 2 motor grader (prefix m9j) service repair manual (m9j0...jfkseksmemqw
This document provides instructions to disassemble the rear axle, differential, and final drive of a 140M 2 motor grader. It lists 29 tools required and provides 42 detailed steps to remove components like the rear axle, sprockets, bearings, housing, carrier assembly, pinion gears, and differential gears. Detailed illustrations accompany each step to show how to position lifting devices and what fasteners to remove. Cautions are provided about cleaning parts and noting shim quantities and positions during disassembly.
Caterpillar cat 140 m 2 motor grader (prefix m9j) service repair manual (m9j0...fusjefjskekmem
The document provides disassembly instructions for the rear axle, differential, and final drive of a 140M 2 motor grader. It lists 29 required tools and provides 43 detailed steps to disassemble these components. These include removing housing components, gears, seals, bearings, and other parts. Weights and lifting precautions are noted for many components. Order and placement of shims and other parts must be recorded during disassembly.
Caterpillar cat 140 m 2 motor grader (prefix m9j) service repair manual (m9j0...fusejkskemfm
This document provides instructions to disassemble the rear axle, differential, and final drive of a 140M 2 motor grader. It lists 29 tools required and provides 42 detailed steps to remove components like the rear axle, sprockets, bearings, housing, carrier assembly, pinion gears, and differential gears. Detailed illustrations accompany each step to show how to position lifting devices and what fasteners to remove. Cautions are provided about cleaning parts and noting shim quantities and positions during disassembly.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...fijsekkdmdm2w
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Numerous specialized tools are required to properly disassemble the components. Technicians are instructed to note part quantities and orders during disassembly.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...zan2736ban
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Numerous specialized tools are required to properly disassemble the components. Technicians are instructed to note part quantities and orders during disassembly.
Caterpillar cat 120 m series 2 motor grader (prefix r9w) service repair manua...fjjsekdmmme
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Required tools include pullers, wrenches, bolts, and lifting devices to safely remove heavier components like housings and gears. Proper disassembly is important to inspect and replace worn parts.
Caterpillar cat 120 m series 2 motor grader (prefix r9w) service repair manua...kdidkdkkd
This document provides disassembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 45 steps to fully disassemble these components, including removing housing components, gears, seals, bearings, and other parts. Required tools include pullers, wrenches, bolts, and lifting devices to safely remove heavier components like housings and gears. Proper disassembly is important to inspect and replace worn parts.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...fujkskemdmdm4r
This document provides disassembly and assembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 48 steps to fully disassemble these components, noting specific tools required and weight of parts. These include removing rear axle, sprockets, bearings, housings, gears, seals, and more. Diagrams illustrate each step. Reassembly follows the disassembly steps in reverse order.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...jdkskmmdmd1
This document provides disassembly and assembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 48 steps to disassemble these components, removing parts like bearings, seals, gears, housings, and shafts. It also lists the required tools, such as link brackets, sleeves, lever pullers, and forcing bolts. The assembly section will provide instructions for reassembling these components in reverse order.
Caterpillar Cat 120M Series 2 Motor Grader (Prefix R9W) Service Repair Manual...fskekkdmdmdm3e
This document provides disassembly and assembly instructions for the rear axle, differential, and final drive of a 120M Series 2 Motor Grader. It lists 48 steps to completely disassemble these components, noting any weights, tools required, and order of removed parts like shims. The assembly procedure is a reverse of the disassembly steps, instructing technicians to clean parts and inspect seals before reinstalling components in the reverse order of removal.
Similar to Caterpillar cat 120 m series 2 motor grader (prefix m9h) service repair manual (m9h00001 and up) (12)
Massey ferguson mf 31 xp combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It contains lists of engine parts with item numbers, part numbers, quantities and descriptions. Reference information is also provided for various engine components that are not serviced individually.
Massey ferguson mf 31 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It consists of multiple sections covering the engine description, cylinder block, crankshaft, pistons, connecting rods, cylinder head and their respective components listed by item number, part number, quantity and description with notes.
Massey ferguson mf 29 xp combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides part numbers and descriptions for components of Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine engines made by Perkins. It includes detailed lists and diagrams of engine parts such as the cylinder block, crankshaft, pistons, connecting rods, cylinder head and other internal components. Each part is numbered and specifications are provided.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualkdidkdkkd
The document provides parts information for a Massey Ferguson MF 265 tractor engine. It includes 36 numbered items with corresponding part numbers, quantities, descriptions, and comments. The parts are grouped into sections for the cylinder block, cylinder head, crankshaft, pistons, timing gears, and other engine components. Measurements are provided in both inches and millimeters for some part thicknesses.
Massey ferguson mf 29 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combines, including Perkins A6.354.4 engines. It contains lists of engine parts with item numbers, part numbers, quantities and descriptions. Reference information and notes are also provided on various engine components.
Massey ferguson mf 375 tractor, b18008 parts catalogue manualkdidkdkkd
The document contains parts lists and descriptions for various components of a Massey Ferguson MF 375 tractor, including the engine, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. It lists over 50 individual parts by number, quantity, description, and other identifying information like serial numbers. The parts are grouped into sections based on the mechanical system or component they belong to.
Massey ferguson mf 362 n tractor (japan only) parts catalogue manualkdidkdkkd
This document provides specifications and part numbers for a Massey Ferguson 362 N tractor intended for the Japanese market. It includes detailed parts lists and diagrams for the engine, cylinder block, crankshaft, pistons, cylinder head, and rocker shaft. Reference numbers are provided for ordering replacement parts.
Massey ferguson mf 390 tractor, b18008 parts catalogue manualkdidkdkkd
This document provides parts information for an MF 390 tractor engine. It includes:
1) A list of engine parts with part numbers and descriptions
2) Serial number ranges and other specifications for some parts
3) Notes on part replacements and specifications for different countries/models
Massey ferguson mf 398 tractor, b18008 parts catalogue manualkdidkdkkd
This document provides a parts list for a Massey Ferguson 398 tractor engine. It includes 33 items related to the cylinder block, including the cylinder block itself, bearings, liners, plugs, bushes, gaskets, and housings. Each part is listed with its part number, quantity, description, and any relevant comments.
Massey ferguson mf 27 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on Massey Ferguson combine engines, including Perkins A6.354.4 engines used in MF 24, 27, 29, 29 XP, 31, and 31 XP combines. It lists over 100 individual parts that make up the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, and other components. Each part is given a reference number, part number, quantity used, description, and any relevant comments.
Massey ferguson mf 24 combine parts catalogue manualkdidkdkkd
This document provides the parts list and diagrams for a Massey Ferguson MF 24 combine with the model number 819723. It includes detailed lists and diagrams of parts for the straw divider, knives and fingers, wearing plates and stone stop, counter shaft, guarding, and feeder drum systems. Over 50 individual parts are specified by part number, quantity, description and placement in the various systems.
Massey ferguson mf 24 combine engines (perkins) parts catalogue manualkdidkdkkd
The document provides details on engines for Massey Ferguson MF 24/27/29/29 XP/31/31 XP combine harvesters, including part numbers, quantities and descriptions of engine components. It lists over 100 individual parts that make up engines, such as the cylinder block, crankshaft, pistons, connecting rods, cylinder head and their corresponding part numbers.
This document provides specifications and dimensions for 'NEF' diesel engines including 3 and 4 cylinder configurations. It describes the lubrication, cooling and turbocharging systems. Dimensions are given for engine blocks, crankshafts, cylinder heads, valves, camshafts and other components. Torque settings are also provided for many engine fasteners.
This document provides specifications and dimensions for 'NEF' diesel engines, including 3 and 4 cylinder models. It describes the engine components such as the injection pumps, lubrication system, cooling system, turbocharger, dimensions, and torque settings. The lubrication system uses a lobe oil pump to circulate oil through the crankshaft, camshaft, cylinder head and oil cooler. The cooling system has a water pump, radiator, thermostat and oil cooler. Turbocharged models include an air filter and turbocharger. Dimensions are provided for piston rings, bearings, valves, camshafts and other components. Torque settings are listed for engine attachment points.
This document provides specifications and dimensions for 'NEF' diesel engines, including 3 and 4 cylinder models. It describes the engine components such as the injection pumps, lubrication system, cooling system, turbocharger, dimensions, and torque settings. The lubrication system uses a lobe oil pump to circulate oil through the crankshaft, camshaft, cylinder head and oil cooler. The cooling system has a water pump, radiator, thermostat and oil cooler. Turbocharged models include an air filter and turbocharger. Dimensions are provided for pistons, cylinders, bearings, valves and other components. Torque settings are listed for various engine fasteners.
Claas nectis ve 237 2+4 wd (type t14) tractor service repair manualkdidkdkkd
1) The document provides identification information for injector pumps used on various tractor models, including the engine, number of cylinders, injector pump model, and injection sequence.
2) It describes the components and operation of the fuel injection system, including the fuel tank, lines, filter, pump, injectors and electrical components like sensors and solenoids.
3) Checks and adjustments are described for components like the accelerator control, injector pump timing, injectors, supply pressure and removal/refitting of the fuel filter. Torque settings and identification information is also provided.
Claas nectis ve 227 2+4 wd (type t14) tractor service repair manualkdidkdkkd
1. The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications of the injector pumps and injectors.
2. The fuel injection system is described including the fuel tank, lines, filters, pump, and injectors. The operating principle and components of the injector pump are explained along with diagrams.
3. Torque settings and adjustment procedures are provided for the accelerator control and injector pump internal settings.
Claas nectis ve 217 2+4 wd (type t14) tractor service repair manualkdidkdkkd
1. The document provides identification information for injector pumps and injectors used in various tractor models. It identifies the manufacturer, models, and specifications of the injector pumps and injectors.
2. The document describes the components and operation of the fuel injection system, including the fuel tank, lines, filters, pump, injector pump, and injectors. It provides diagrams and explanations of how fuel is delivered to the injectors.
3. The document provides instructions for adjusting the accelerator control and setting the internal timing of the injector pump when removed from the engine. It describes the proper alignment and measurements needed for adjusting the pump timing.
Claas nectis f 267 2+4 wd (type t16) tractor service repair manualkdidkdkkd
This document provides specifications for Iveco NEF diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication, cooling, and turbocharging systems. Dimensions are provided for pistons, crankshafts, cylinder heads, valves, and other components. Clearances and tolerances are indicated. The engines have mechanical injection pumps and use a pressurized lubrication system with an oil pump and filter. The closed-loop cooling system includes a water pump, radiator, and thermostat. Turbocharged versions get air from a compressor driven by the exhaust system.
Claas nectis f 257 2+4 wd (type t16) tractor service repair manualkdidkdkkd
This document provides specifications for Iveco NEF diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication, cooling, and turbocharging systems. Dimensions are provided for pistons, crankshafts, cylinder heads, valves, and other components. Clearances and tolerances are indicated. The engines have mechanical injection pumps and use a pressurized lubrication system with an oil pump and filter. The closed-loop cooling system includes a water pump, radiator, and thermostat. Turbocharged versions get air from a compressor driven by the exhaust system.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120M 2 MOTOR GRADER M9H
Configuration: 120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
120M Series 2 Motor Grader Power Train
Media Number -KENR9467-02 Publication Date -01/05/2017 Date Updated -16/05/2017
i06013976
Rear Axle, Differential and Final Drive - Disassemble
SMCS - 3258-015; 3278-015; 3282-015-RE; 4050-015; 4068-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 4
B 140-7742 Sleeve 2
C 386-6031 Lever Puller Hoist 1
D 154-6182 Forcing Bolt 3
E 439-3939 Link Bracket 2
F
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
G 292-4949 Socket Wrench As 1
H 154-6183 Forcing Bolt 3
J 1U-6405 Three Jaw Puller 1
Start By:
A. Remove the rear axle.
1/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
Illustration 1 g01413868
1. Use Tooling (A) , Tooling (B) , and two suitable lifting devices in order to position rear axle
(1) onto suitable blocking. The weight of rear axle (1) is approximately 1089 kg (2400 lb).
Illustration 2 g01418559
2/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 2. Remove bolts (3) , retainer (4) , shims (5) , sprocket (2) , and sprocket (6) .
Note: Note the quantity and the order of shims (5) .
Illustration 3 g01414357
3. Remove bearing cone (7) .
Illustration 4 g01412778
3/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 4. Attach Tooling (A) , Tooling (C) , and two suitable lifting devices onto final drive housing
(8) . The weight of final drive housing (8) is approximately 191 kg (420 lb). Remove nuts
(9) and bolts (9A) .
5. Use Tooling (D) in order to remove final drive housing (8) .
Illustration 5 g01419912
6. Remove bolts (10) . Remove retainer (11) .
Illustration 6 g01352280
7. Remove shims (12) . Use Tooling (A) and a suitable lifting device in order to remove
housing (13) . The weight of housing (13) is approximately 54 kg (120 lb).
Note: Note the quantity and the order of shims (12) .
4/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 7 g01352292
8. Remove thrust washer (14) . Remove wear sleeves (15) .
Illustration 8 g01352299
9. Turn over housing (13) . Remove lip seal (16) .
Illustration 9 g01414353
10. Remove bearing cup (17) . Remove thrust washer (18) .
5/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g01352320
11. Remove lip seal (19) . Remove bearing cup (20) .
Illustration 11 g01419983
12. Use Tooling (E) in order to remove carrier assembly (21) and drive shaft (22) . The weight
of carrier assembly (21) and drive shaft (22) is approximately 136 kg (300 lb).
6/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 12 g01419985
13. Use Tooling (F) in order to remove bearing cone (23) .
Illustration 13 g01352339
14. Remove retaining ring (24) in order to remove axle shaft (22) from carrier assembly (21) .
Illustration 14 g01352406
15. Remove bolts (25) and retainer (26) . Remove pin (27) . Remove gear (28) . Remove thrust
washers (29) and bearings (30) . Repeat this step for the remaining planetary gears.
7/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 15 g01352384
16. Remove axle shaft assembly (31) .
Illustration 16 g01352402
17. Remove retaining ring (32) in order to remove gear (33) from axle shaft (34) .
Illustration 17 g01352438
18. Use Tooling (D) in order to separate ring gear (35) from the intermediate housing.
8/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 18 g01352445
19. Use Tooling (B) and a suitable lifting device in order to remove ring gear (35) . The weight
of ring gear (35) is approximately 25 kg (55 lb).
20. Repeat Step 2 through Step 19 for the opposite side.
Illustration 19 g01353587
21. Position differential housing (36) with intermediate housing (37) upward.
9/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 20 g01419994
22. Attach a suitable lifting device onto pinion (38) . Use Tooling (H) in order to separate
pinion (38) from the center housing. Remove bolts (39) in order to remove pinion (38) . The
weight of pinion (38) is approximately 56 kg (123 lb).
Illustration 21 g01353021
23. Remove shims (40) . Remove O-ring seal (41) .
Note: Note the order and the quantity of shims (40) .
10/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 22 g01353002
24. Remove bolt (42) . Remove retainer (43) . Remove yoke (44) . Remove guard (45) .
Illustration 23 g01353512
25. Remove shims (46) . Remove lip seal (47) .
Note: Note the order and the quantity of shims (46) .
Illustration 24 g01353570
26. Remove pinion (48) . Remove bearing cone (49) . Remove bearing cup (50) . Remove
bearing cone (51) . Remove bearing cup (52) .
27. Use Tooling (G) in order to remove nut assembly (54) .
11/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 25 g03772865
28. Remove bolts (53) . Remove bolts (54) .
Illustration 26 g01419996
Typical Example
29. Use Tooling (J) in order to separate intermediate housing (37) from differential housing
(36) .
12/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 27 g01420124
Typical Example
30. Use Tooling (E) in order to remove intermediate housing (37) . The weight of intermediate
housing (37) is approximately 32 kg (71 lb).
Illustration 28 g03772901
Typical Example
31. Before installing Tooling (A) remove the shims. Use Tooling (A) in order to remove
bearing assembly (55) and differential (56) . The weight of bearing assembly (55) and
differential (56) is approximately 102 kg (225 lb).
13/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 29 g03772885
32. Remove bolts (57) . Remove shroud (58) .
Illustration 30 g03772948
33. Remove bolts (59) . Use Tooling (G) and remove lock-nut (60) .
Illustration 31 g03772966
34. Use Tooling (F) in order to remove bearing assembly (55) .
14/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 32 g01354900
35. Remove bearing cone (63) . Remove bearing cups (64) .
Illustration 33 g01420000
36. Use Tooling (J) in order to remove spacer (65) and bearing cone (66) .
Note: This step is a destructive procedure. Replace bearing cone (66) .
15/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 34 g01353751
37. Remove retaining ring (67) . Remove bearing race (68) . Remove O-ring seals (69) .
Remove thrust ring (70) .
Illustration 35 g01353760
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
38. Remove bolts (71) . Remove case (72) .
16/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 36 g01353766
39. Remove thrust washer (73) . Remove plates (74) and discs (75) . Remove springs (76) .
Note: Note the quantity and the order of plates (74) and discs (75) .
Illustration 37 g01353940
40. Remove housing (77) .
Illustration 38 g01353944
41. Remove differential gear (78) .
17/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 39 g01353945
42. Remove spider assembly (79) .
Illustration 40 g01353954
43. Remove thrust washer (80) , pinion gear (81) , and bearing sleeve (82) from spider (83) .
Repeat this step for the remaining pinion gears (81) .
Illustration 41 g01353965
18/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 44. Remove differential gear (84) . Remove thrust washer (85) .
Illustration 42 g01353970
45. Use two people in order to turn over housing (86) and bevel gear (87) . The combined
weight of housing (86) and bevel gear (87) is approximately 59 kg (130 lb). Remove bolts
(88) . Use two people in order to remove housing (86) from bevel gear (87) . The weight of
housing (86) is approximately 41 kg (90 lb). The weight of bevel gear (87) is approximately
19 kg (41 lb).
Illustration 43 g01355203
46. Remove bearing assembly (89) . Remove piston (90) .
19/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 44 g01355208
47. Remove thrust race (91) , thrust bearing (92) , and thrust race (93) from piston (90) .
Illustration 45 g01355211
48. Remove seals (94) from piston (90) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 8 13:06:42 UTC+0800 2020
20/20
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POW...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120M 2 MOTOR GRADER M9H
Configuration: 120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
120M Series 2 Motor Grader Power Train
Media Number -KENR9467-02 Publication Date -01/05/2017 Date Updated -16/05/2017
i07285127
Rear Axle, Differential and Final Drive - Assemble
SMCS - 3258-016; 3278-016; 3282-016-RE; 4050-016; 4068-016
Assembly Procedure
Table 1
Required Tools
Tool
Part
Number
Part Description Qty
A 439-3940 Link Bracket 4
B 140-7742 Sleeve 2
C 386-6031 Lever Puller Hoist 1
E 143-3939 Link Bracket 2
G 292-4949 Socket Wrench As 1
H 154-6183 Forcing Bolt 2
K 4C-4030 Thread Lock Compound 1
L 1U-8846 Gasket Sealant 1
M
6V-2012 Depth Micrometer 1
367-9109 Caliper(1)
1
N
8T-5096 Dial Indicator Gp 1
301-3405 Gauge 1
P 8T-4140 Bolt 4
R 7M-7456 Bearing Mount Compound 1
1/27
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. S - Cat Advance 3Moly Grease or Dow Corning Molykote BR2 -
Plus
1
T 8T-5096 Dial Indicator Gp 1
(1)
For use with three bolt retainers
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals, gaskets, and lip seals. Replace O-ring seals, gaskets, and lip seals
that are worn or damaged.
Note: Lubricate O-ring seals and lip seals with the lubricant that is being sealed.
Illustration 1 g03831520
1. Install seals (94) onto piston (90).
Illustration 2 g03831488
2/27
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Note: Grease is used to hold thrust race (93) and thrust bearing (92) in place during
assembly.
2. Apply a liberal amount of grease to thrust race (93) and to thrust bearing (92). Install thrust
race (93) and thrust bearing (92) onto piston (90).
Illustration 3 g01355203
3. Install piston (90). Lower the temperature of bearing assembly (89). Install bearing
assembly (89).
Illustration 4 g01353970
4. Use two people to install housing (86) onto bevel gear (87). The weight of housing (86) is
approximately 41 kg (90 lb). Install bolts (88). Tighten bolts (88) to a torque of
300 ± 40 N·m (221 ± 30 lb ft).
5. Use two people to turn over bevel gear (87) and housing (86). The combined weight of
bevel gear (87) and housing (86) is approximately 59 kg (130 lb).
3/27
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 5 g01353965
6. Install thrust washer (85). Install differential gear (84).
Note: Install thrust washer (85) with the groove side against gear (84).
Illustration 6 g01353954
7. Install bearing sleeve (82), pinion gear (81), and thrust washer (80) onto spider (83). Repeat
this step for the remaining pinion gears (81).
Illustration 7 g01353945
8. Install spider assembly (79).
4/27
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 8 g01353944
9. Install differential gear (78).
Illustration 9 g01353940
10. Install housing (77).
Note: Ensure that the notches on the housings are aligned.
Illustration 10 g01353766
5/27
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 11. Install plates (74) and discs (75). Install thrust washer (73). Install springs (76).
Note: Lubricate the discs with the lubricant that is being sealed.
Note: Install thrust washer (73) with the groove side against the gear.
Illustration 11 g01353760
Typical Example
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Determine bolt size before torquing bolts (71).
12. Install case (72). Install bolts (71). Tighten M16 bolts (71) to a torque of 300 ± 40 N·m
(220 ± 30 lb ft). Tighten M12 bolts (71) to a torque of 120 ± 20 N·m (90 ± 15 ft)
6/27
120M Series 2 Motor Grader - All Wheel Drive M9H00001-UP (MACHINE) POWER...
2020/5/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...