This service manual provides information on servicing and repairing the SR270, SV340, TR340, and TV380 skid steer loaders and compact track loaders. It covers the engine, fuel system, cooling system, lubrication system, power coupling, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, wheels, tracks, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual includes introduction sections on safety, fluids, specifications, identification, and basic instructions for servicing. It provides exploded views and specifications for replacement parts.
Case cx210 c crawler excavator service repair manualdfujsjefjkskemm
This document is a service manual for a CX210C crawler excavator. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms dippers and buckets, and the platform, cab, bodywork and decals. Each section contains multiple subsections that provide detailed instructions and part numbers for repair and maintenance of specific components. The introduction emphasizes the importance of qualified dealership personnel strictly following the procedures in the manual and using approved parts for any repair or maintenance work.
Case cx490 c crawler excavator service repair manual instant downloadyhfhjjsenne
This service manual provides maintenance and repair information for the CX490C crawler excavator. The manual is divided into sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms dippers and buckets, and the platform, cab, bodywork and decals. Safety precautions are outlined and each major system includes subsections listing specific components.
Case cx370 c crawler excavator service repair manualfusfejskekem
Here are the steps to prepare for servicing the engine and crankcase:
1. Park the machine on a level surface, engage the parking brake, lower all implements, shut off the engine, and remove the ignition key.
2. Relieve all pressure from hydraulic circuits before disconnecting lines. Vent high pressure gas from air conditioning circuits before loosening lines.
3. Use lifting equipment such as a shackle rated for the weight of heavy components to safely lift and handle them. Keep the work area clear of bystanders.
4. Prepare wrenches in the required sizes to remove fasteners.
5. Ventilate the work area when servicing batteries or charging to avoid explosive gases
Case cx240 c crawler excavator service repair manualfujsjefjskkem
The document is a service manual that provides maintenance and repair information for the CX240C crawler excavator. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms/dippers/buckets, and the cab/bodywork. The engine section provides specifications and descriptions of the engine components, cooling system, electrical system, and identification information. It describes the electronic engine control and components like the cylinder block, heads, crankshaft, and common rail fuel injection system.
Case cx490 c crawler excavators lc version (tier 3) turkish market service ...fusjejfjsekfkem
This service manual section provides specifications for the Isuzu 6UZ1 diesel engine, including its cooling system, lubrication system, and electrical system. The engine is an inline 6-cylinder overhead cam design with a displacement of 9.839 liters. Maximum output is 270 kW at 2000 RPM with maximum torque of 1435 Nm at 1500 RPM. Coolant capacity is 22.5 liters and oil capacity ranges from 30-41 liters. The generator is a 24V/50A unit while the starter is 24V/5.5kW.
Case cx490 c tier iii crawler excavator service repair manualfjjskekksemmm
This document is a service manual that provides maintenance and repair instructions for CX490C and CX500C crawler excavators. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms, dippers, buckets, and the platform, cab, bodywork, and decals. The introduction emphasizes that all repair and maintenance work must be carried out by qualified personnel according to the procedures in the manual using special tools, and the manufacturer is not responsible for damages caused by unauthorized parts.
Case cx500 c tier iii crawler excavator service repair manualfjjskekksemmm
The document is a service manual section about an engine. It provides specifications for the engine including displacement, power output, cooling system, lubrication system, electrical system, starter, glow plug, and special tools for working on the engine. Key details covered include the engine model, cylinder configuration, bore and stroke, compression ratio, and component manufacturers.
Case cx500 c tier iii crawler excavator service repair manualyfhjsjefkksemme
The document is a service manual section about an engine. It provides specifications for the engine including displacement, power output, cooling system details, lubrication system details, dimensions, valve timing, and electrical system components. It also lists special tools needed for tasks like removing and installing cylinder liners.
Case cx210 c crawler excavator service repair manualdfujsjefjkskemm
This document is a service manual for a CX210C crawler excavator. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms dippers and buckets, and the platform, cab, bodywork and decals. Each section contains multiple subsections that provide detailed instructions and part numbers for repair and maintenance of specific components. The introduction emphasizes the importance of qualified dealership personnel strictly following the procedures in the manual and using approved parts for any repair or maintenance work.
Case cx490 c crawler excavator service repair manual instant downloadyhfhjjsenne
This service manual provides maintenance and repair information for the CX490C crawler excavator. The manual is divided into sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms dippers and buckets, and the platform, cab, bodywork and decals. Safety precautions are outlined and each major system includes subsections listing specific components.
Case cx370 c crawler excavator service repair manualfusfejskekem
Here are the steps to prepare for servicing the engine and crankcase:
1. Park the machine on a level surface, engage the parking brake, lower all implements, shut off the engine, and remove the ignition key.
2. Relieve all pressure from hydraulic circuits before disconnecting lines. Vent high pressure gas from air conditioning circuits before loosening lines.
3. Use lifting equipment such as a shackle rated for the weight of heavy components to safely lift and handle them. Keep the work area clear of bystanders.
4. Prepare wrenches in the required sizes to remove fasteners.
5. Ventilate the work area when servicing batteries or charging to avoid explosive gases
Case cx240 c crawler excavator service repair manualfujsjefjskkem
The document is a service manual that provides maintenance and repair information for the CX240C crawler excavator. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms/dippers/buckets, and the cab/bodywork. The engine section provides specifications and descriptions of the engine components, cooling system, electrical system, and identification information. It describes the electronic engine control and components like the cylinder block, heads, crankshaft, and common rail fuel injection system.
Case cx490 c crawler excavators lc version (tier 3) turkish market service ...fusjejfjsekfkem
This service manual section provides specifications for the Isuzu 6UZ1 diesel engine, including its cooling system, lubrication system, and electrical system. The engine is an inline 6-cylinder overhead cam design with a displacement of 9.839 liters. Maximum output is 270 kW at 2000 RPM with maximum torque of 1435 Nm at 1500 RPM. Coolant capacity is 22.5 liters and oil capacity ranges from 30-41 liters. The generator is a 24V/50A unit while the starter is 24V/5.5kW.
Case cx490 c tier iii crawler excavator service repair manualfjjskekksemmm
This document is a service manual that provides maintenance and repair instructions for CX490C and CX500C crawler excavators. It contains sections covering the engine, hydraulic systems, frames and ballasting, tracks and track suspension, cab climate control, electrical systems, booms, dippers, buckets, and the platform, cab, bodywork, and decals. The introduction emphasizes that all repair and maintenance work must be carried out by qualified personnel according to the procedures in the manual using special tools, and the manufacturer is not responsible for damages caused by unauthorized parts.
Case cx500 c tier iii crawler excavator service repair manualfjjskekksemmm
The document is a service manual section about an engine. It provides specifications for the engine including displacement, power output, cooling system, lubrication system, electrical system, starter, glow plug, and special tools for working on the engine. Key details covered include the engine model, cylinder configuration, bore and stroke, compression ratio, and component manufacturers.
Case cx500 c tier iii crawler excavator service repair manualyfhjsjefkksemme
The document is a service manual section about an engine. It provides specifications for the engine including displacement, power output, cooling system details, lubrication system details, dimensions, valve timing, and electrical system components. It also lists special tools needed for tasks like removing and installing cylinder liners.
Hyster f187 (s50 ft) forklift service repair manualfdujdfjjsekkem
The document provides repair procedures for replacing the torque converter in a transmission. It describes removing the transmission from the lift truck, separating it from the engine, and removing the torque converter. It then explains inspecting parts and installing a new torque converter, reattaching the transmission to the engine, and reinstalling components like wiring harnesses. Key steps include draining transmission oil, removing mounting bolts, and ensuring proper alignment of splines when reinstalling.
Hyster e114 (e25 z) forklift service repair manualfdujdfjjsekkem
This document provides a description and repair procedures for a steering housing and steering control unit. It describes the main components of the steering system, including the steering column, steering control unit, and steering housing. The steering housing holds the steering column and control unit, and can be adjusted for operator comfort. The steering control unit is a rotary valve that controls oil flow to the steering cylinder during operation, directing the steer tires. Even without the steering pump operating, limited steering is still possible through a check valve.
Hyster d114 (e1.75 xm europe) forklift service repair manualfdujdfjjsekkem
This document provides specifications for service and repair of various models of electric forklifts, including:
- Torque values for drive wheel bolts, steer wheel nuts, and spindle nuts.
- Standard and optional tire sizes for drive and steer wheels.
- Counterweight sizes for different models.
- Hydraulic system relief pressure specifications.
- Battery compartment sizes and battery specifications for different models.
- Maximum carriage and tilt creep rates at various temperatures.
- Mast speeds for different models under various conditions.
Hyster c108 (e2.50 xl europe) forklift service repair manualfdujdfjjsekkem
This document provides information about steering systems for electric lift trucks. It describes the components and operation of power steering and power steering with on-demand systems. The key components are the steering wheel, optical encoder, activator, steering control unit, steering pump motor, steering pump, and hydraulic steering motor or steering cylinder. It also provides repair procedures for the steering wheel and column assembly, including removal and installation of components. Diagrams are included to illustrate the steering system components and hydraulic schematic.
Hyster c008 (h650 c) forklift service repair manualfdujdfjjsekkem
1) The document provides information on servicing gear pumps, including descriptions of their components and operation. It discusses the types of repairs commonly needed on gear pumps.
2) The procedures for disassembling, cleaning, inspecting, and reassembling gear pumps are outlined. Care must be taken to prevent dirt from entering the pump during repair.
3) Worn seals are a common cause of pump failure. Gears, housings, thrust plates and other parts are inspected for acceptable wear levels and damage. Replacement is usually needed if wear exceeds specified thresholds.
Cummins onan generator set with power command 3100 controller model (dqaa ) s...fdujdfjjsekkem
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbf ) s...fdujdfjjsekkem
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance/repair procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbc ) s...fdujdfjjsekkem
This document is a service manual that provides information for troubleshooting and servicing generator sets equipped with PowerCommand 3100 controllers. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and details regarding the generator set control functions, components, testing procedures, and maintenance.
Case tv370 tier 4 b (final) alpha series compact track loader service repair ...fdujdfjjsekkem
This document provides instructions for locking the loader arms and tilting the cab on radial lift skid steer and compact track loaders. It warns of crushing hazards and outlines safety procedures, including never entering or exiting the cab while the loader arms are raised and unsupported. It instructs having two people, with one removing the support strut while the operator remains in the cab.
Case sv250 tier 4 a alpha series skid steer loader service repair manual pin ...fdujdfjjsekkem
This document is a service manual for Case skid steer loaders and compact track loaders. It provides information on safety procedures, torque specifications, product identification, and maintenance instructions for the engine, front axle, rear axle, and other components. The manual instructs technicians to perform all repair and maintenance work according to the procedures outlined and using the specified tools.
Case sr240 tier 4 b (final) and stage iv alpha series skid steer loader servi...fdujdfjjsekkem
1. Lower the loader arms fully to the ground and engage the loader arm locks.
2. Set the parking brake and shut off the engine.
3. Unlatch and tilt the cab forward to gain access to service areas underneath.
Case sr240 tier 4 b (final) alpha series skid steer loader service repair manualfdujdfjjsekkem
This document is a service manual that provides instructions and specifications for servicing Case construction equipment, including skid steer loaders and compact track loaders. It contains sections on the engine, power coupling, front and rear axles, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. The document provides standard torque specifications for hydraulics and minimum tightening torques for normal assembly. It also includes safety rules and notices for working on the equipment.
Case sr130 tier 4 b (final) alpha series skid steer loader service repair manualfdujdfjjsekkem
This document provides instructions for removing the engine from SR130 and SR160 skid steer loaders with Tier 4 engines. The key steps include draining fluids, removing radiator, oil cooler, fan, muffler, intake tube, air cleaner housing, hoses, wires for glow plugs, starter, alternator, senders, and disconnecting the negative battery cable. Safety warnings are provided to relieve pressure before disconnecting lines and ensure all movement has stopped before servicing.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Hyster f187 (s50 ft) forklift service repair manualfdujdfjjsekkem
The document provides repair procedures for replacing the torque converter in a transmission. It describes removing the transmission from the lift truck, separating it from the engine, and removing the torque converter. It then explains inspecting parts and installing a new torque converter, reattaching the transmission to the engine, and reinstalling components like wiring harnesses. Key steps include draining transmission oil, removing mounting bolts, and ensuring proper alignment of splines when reinstalling.
Hyster e114 (e25 z) forklift service repair manualfdujdfjjsekkem
This document provides a description and repair procedures for a steering housing and steering control unit. It describes the main components of the steering system, including the steering column, steering control unit, and steering housing. The steering housing holds the steering column and control unit, and can be adjusted for operator comfort. The steering control unit is a rotary valve that controls oil flow to the steering cylinder during operation, directing the steer tires. Even without the steering pump operating, limited steering is still possible through a check valve.
Hyster d114 (e1.75 xm europe) forklift service repair manualfdujdfjjsekkem
This document provides specifications for service and repair of various models of electric forklifts, including:
- Torque values for drive wheel bolts, steer wheel nuts, and spindle nuts.
- Standard and optional tire sizes for drive and steer wheels.
- Counterweight sizes for different models.
- Hydraulic system relief pressure specifications.
- Battery compartment sizes and battery specifications for different models.
- Maximum carriage and tilt creep rates at various temperatures.
- Mast speeds for different models under various conditions.
Hyster c108 (e2.50 xl europe) forklift service repair manualfdujdfjjsekkem
This document provides information about steering systems for electric lift trucks. It describes the components and operation of power steering and power steering with on-demand systems. The key components are the steering wheel, optical encoder, activator, steering control unit, steering pump motor, steering pump, and hydraulic steering motor or steering cylinder. It also provides repair procedures for the steering wheel and column assembly, including removal and installation of components. Diagrams are included to illustrate the steering system components and hydraulic schematic.
Hyster c008 (h650 c) forklift service repair manualfdujdfjjsekkem
1) The document provides information on servicing gear pumps, including descriptions of their components and operation. It discusses the types of repairs commonly needed on gear pumps.
2) The procedures for disassembling, cleaning, inspecting, and reassembling gear pumps are outlined. Care must be taken to prevent dirt from entering the pump during repair.
3) Worn seals are a common cause of pump failure. Gears, housings, thrust plates and other parts are inspected for acceptable wear levels and damage. Replacement is usually needed if wear exceeds specified thresholds.
Cummins onan generator set with power command 3100 controller model (dqaa ) s...fdujdfjjsekkem
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbf ) s...fdujdfjjsekkem
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance/repair procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbc ) s...fdujdfjjsekkem
This document is a service manual that provides information for troubleshooting and servicing generator sets equipped with PowerCommand 3100 controllers. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual contains important safety instructions and details regarding the generator set control functions, components, testing procedures, and maintenance.
Case tv370 tier 4 b (final) alpha series compact track loader service repair ...fdujdfjjsekkem
This document provides instructions for locking the loader arms and tilting the cab on radial lift skid steer and compact track loaders. It warns of crushing hazards and outlines safety procedures, including never entering or exiting the cab while the loader arms are raised and unsupported. It instructs having two people, with one removing the support strut while the operator remains in the cab.
Case sv250 tier 4 a alpha series skid steer loader service repair manual pin ...fdujdfjjsekkem
This document is a service manual for Case skid steer loaders and compact track loaders. It provides information on safety procedures, torque specifications, product identification, and maintenance instructions for the engine, front axle, rear axle, and other components. The manual instructs technicians to perform all repair and maintenance work according to the procedures outlined and using the specified tools.
Case sr240 tier 4 b (final) and stage iv alpha series skid steer loader servi...fdujdfjjsekkem
1. Lower the loader arms fully to the ground and engage the loader arm locks.
2. Set the parking brake and shut off the engine.
3. Unlatch and tilt the cab forward to gain access to service areas underneath.
Case sr240 tier 4 b (final) alpha series skid steer loader service repair manualfdujdfjjsekkem
This document is a service manual that provides instructions and specifications for servicing Case construction equipment, including skid steer loaders and compact track loaders. It contains sections on the engine, power coupling, front and rear axles, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. The document provides standard torque specifications for hydraulics and minimum tightening torques for normal assembly. It also includes safety rules and notices for working on the equipment.
Case sr130 tier 4 b (final) alpha series skid steer loader service repair manualfdujdfjjsekkem
This document provides instructions for removing the engine from SR130 and SR160 skid steer loaders with Tier 4 engines. The key steps include draining fluids, removing radiator, oil cooler, fan, muffler, intake tube, air cleaner housing, hoses, wires for glow plugs, starter, alternator, senders, and disconnecting the negative battery cable. Safety warnings are provided to relieve pressure before disconnecting lines and ensure all movement has stopped before servicing.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
6. Contents
INTRODUCTION
Foreword - Important notice regarding equipment servicing (*) ................................ 3
Safety rules (*) .................................................................................. 4
Safety rules - Personal safety (*) ............................................................... 5
Safety rules - Ecology and the environment (*) ................................................. 6
Torque - Minimum tightening torques for normal assembly (*) ................................. 7
Torque - Standard torque data for hydraulics (*) .............................................. 12
Basic instructions - Shop and assembly (*) ................................................... 14
Basic instructions - Video links ............................................................... 16
Hydraulic contamination (*) ................................................................... 17
Fluids and lubricants .......................................................................... 18
General specification - Recommended engine oil for operating temperature ranges (*) ..... 19
Product identification (*) ...................................................................... 20
Product identification - Machine orientation (*) ............................................... 23
(*) See content for specific models
47916277 26/10/2016
2
7. INTRODUCTION
Foreword - Important notice regarding equipment servicing
SR270 TIER 4B (FINAL) [NGM418237 - ] NA
SV340 NA
TR340 TIER 4B (FINAL) [NGM418237 - ] NA
TV380 NA
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE CONSTRUCTION Sales and Service Networks.
47916277 26/10/2016
3
8. INTRODUCTION
Safety rules
SV340 TIER 4B (FINAL) [NGM418237 - ] NA
TV380 NA
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47916277 26/10/2016
4
9. INTRODUCTION
Safety rules - Personal safety
SR270 TIER 4B (FINAL) [NGM418237 - ] NA
SV340 NA
TR340 TIER 4B (FINAL) [NGM418237 - ] NA
TV380 NA
Carefully study these precautions, and those included in the external attachment operators
manual, and insist that they be followed by those working with and for you.
1. Thoroughly read and understand this manual and the attachment Operator’s Manual before operating this or any
other equipment.
2. Be sure all people and pets are clear of the machine before starting. Sound the horn, if equipped, three times
before starting engine.
3. Only the operator should be on the machine when in operation. Never allow anyone to climb on to the machine
while it is in motion. If the machine is equipped with an Instructors Seat, this must only be used for training
purposes. Passengers must not be allowed to use the Instructors Seat.
4. Keep all shields in place. Never work around the machine or any of the attachments while wearing loose clothing
that might catch on moving parts.
5. Observe the following precautions whenever lubricating the machine or making adjustments.
• Disengage all clutching levers or switches.
• Lower the attachment, if equipped, to the ground or raise the attachment completely and engage the cylinder
safety locks. Completing these actions will prevent the attachment from lowering unexpectedly.
• Engage the parking brake.
• Shut off the engine and remove the key.
• Wait for all machine movement to stop before leaving the operators platform.
6. Always keep the machine in gear while travelling downhill.
7. The machine should always be equipped with sufficient front or rear axle weight for safe operation.
8. Under some field conditions, more weight may be required at the front or rear axle for adequate stability. This is
especially important when operating in hilly conditions or/when using heavy attachments.
9. Always lower the attachment, shut off the engine, set the parking brake, engage the transmission gears, remove
the key and wait for all machine movement to stop before leaving the operators platform.
10. If the attachment or machine should become obstructed or plugged; set the parking brake, shut off the engine
and remove the key, engage the transmission gears, wait for all machine or attachment motion to come to a stop,
before leaving the operators platform to removing the obstruction or plug.
11. Never disconnect or make any adjustments to the hydraulic system unless the machine and/or the attachment is
lowered to the ground or the safety lock(s) is in the engaged position.
12. Use of the flashing lights is highly recommended when operating on a public road.
13. When transporting on a road or highway, use accessory lights and devices for adequate warning to the opera-
tors of other vehicles. In this regard, check local government regulations. Various safety lights and devices are
available from your CASE CONSTRUCTION dealer.
14. Practice safety 365 days a year.
15. Keep all your equipment in safe operating condition.
16. Keep all guards and safety devices in place.
17. Always set the parking brake, shut off the engine and remove the key, engage the transmission gears, wait for all
machine or attachment motion to come to a stop, before leaving the operators platform to service the machine
and attachment.
18. Remember: A careful operator is the best insurance against an accident.
19. Extreme care should be taken in keeping hands and clothing away from moving parts.
47916277 26/10/2016
5
10. INTRODUCTION
Safety rules - Ecology and the environment
SR270 TIER 4B (FINAL) [NGM418237 - ] NA
SV340 NA
TR340 TIER 4B (FINAL) [NGM418237 - ] NA
TV380 NA
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
• Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
• The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. CASE
CONSTRUCTION strongly recommends that you return all used batteries to a CASE
CONSTRUCTION dealer, who will dispose of the used batteries or recycle the used
batteries properly. In some countries, this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
• Accept the return of your used batteries
• Store the returned batteries in a suitable location
• Send the returned batteries to the battery manufacturer for recycling
47916277 26/10/2016
6
14. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. INTRODUCTION
Inch Lock Nuts, All Metal (Three optional methods)
20090268 4
Grade Identification
Grade Corner Marking Method (1) Flats Marking Method (2) Clock Marking Method (3)
Grade A No Notches No Mark No Marks
Grade B One Circumferential Notch Letter B Three Marks
Grade C Two Circumferential Notches Letter C Six Marks
47916277 26/10/2016
11