This document is a service manual for Case IH Titan 3030, 3530, 4030, and 4530 tractors. It contains safety rules, specifications, capacities, and maintenance information for the hydraulic, pneumatic, electrical, engine, transmission, axle, frame, and other systems of the tractors. The document includes torque specifications for various bolt sizes and types used on the tractors.
Yamaha 50 geto outboard service repair manual l 400805 fjjskekksemmm
This document is a service manual that provides specifications, inspection and adjustment procedures, troubleshooting information, and general information for maintaining various Yamaha outboard motor models. It lists special tools that are recommended for accurate assembly, adjustment, and repair of the equipment. These include tools for measuring idle speed, ignition and electrical systems, fuel components, lower unit components, pinion and forward gearcase shimming, and more. Proper tools and safety practices are emphasized to protect parts from damage during disassembly and reassembly.
Kubota v3800 cr-te4 diesel engine service repair manualufuusefjjsekkm
The document provides specifications for 6 diesel engine models: V3800-CR-TE4, V3800-CR-TE4C, V3800-CR-TIE4, V3800-CR-TIE4C, V3800-TIE4, and V3800-TIE4C. The specifications include information such as the number of cylinders, displacement, power output, lubrication system, cooling system, dimensions, and fuel and oil requirements. The engines are vertical, water-cooled, 4-cycle direct injection diesel engines with a bore of 100mm and stroke of 120mm for a total displacement of 3769cm3.
Yamaha outboard 40 veto, 40tr service repair manual l 544974 fjjskeknjufksemm
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning/lubricating parts during disassembly and assembly.
Yamaha outboard 40 veo, 40er service repair manual s 110760 fjskeksemm
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning and lubricating parts during disassembly and assembly.
Yamaha outboard 40 veto, 40tr service repair manual l 544974 fjjskekskem
This document provides a service manual for 40V and 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning and lubricating parts during disassembly and assembly.
Yamaha outboard 40 veto, 40tr service repair manual x 900196 fhjsekkemm
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning/lubricating parts during disassembly and assembly.
Yamaha outboard 40 veto, 40tr service repair manual s 880367 fjskkmemem
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning/lubricating parts during disassembly and assembly.
Massey Ferguson MF2625 TRACTOR - MADE IN INDIA FOR MEXICO, SOUTH AMERICA, AUS...ufjjsejkkemmd
This document contains parts lists and technical specifications for the engine, fuel system, and exhaust system of a Massey Ferguson 2625 tractor made in India for markets in Mexico, South America, Australia, and New Zealand. It includes lists of parts for the engine block, cylinder head, crankshaft, pistons, valves, and other internal engine components along with part numbers and quantities of each part. The document provides specifications for the engine depending on whether it has a rotary fuel pump or inline fuel injection pump.
Yamaha 50 geto outboard service repair manual l 400805 fjjskekksemmm
This document is a service manual that provides specifications, inspection and adjustment procedures, troubleshooting information, and general information for maintaining various Yamaha outboard motor models. It lists special tools that are recommended for accurate assembly, adjustment, and repair of the equipment. These include tools for measuring idle speed, ignition and electrical systems, fuel components, lower unit components, pinion and forward gearcase shimming, and more. Proper tools and safety practices are emphasized to protect parts from damage during disassembly and reassembly.
Kubota v3800 cr-te4 diesel engine service repair manualufuusefjjsekkm
The document provides specifications for 6 diesel engine models: V3800-CR-TE4, V3800-CR-TE4C, V3800-CR-TIE4, V3800-CR-TIE4C, V3800-TIE4, and V3800-TIE4C. The specifications include information such as the number of cylinders, displacement, power output, lubrication system, cooling system, dimensions, and fuel and oil requirements. The engines are vertical, water-cooled, 4-cycle direct injection diesel engines with a bore of 100mm and stroke of 120mm for a total displacement of 3769cm3.
Yamaha outboard 40 veto, 40tr service repair manual l 544974 fjjskeknjufksemm
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning/lubricating parts during disassembly and assembly.
Yamaha outboard 40 veo, 40er service repair manual s 110760 fjskeksemm
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning and lubricating parts during disassembly and assembly.
Yamaha outboard 40 veto, 40tr service repair manual l 544974 fjjskekskem
This document provides a service manual for 40V and 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning and lubricating parts during disassembly and assembly.
Yamaha outboard 40 veto, 40tr service repair manual x 900196 fhjsekkemm
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning/lubricating parts during disassembly and assembly.
Yamaha outboard 40 veto, 40tr service repair manual s 880367 fjskkmemem
This document provides a service manual for 40V, 50H outboard motors. It includes an index listing chapters covering general information, specifications, periodic inspection and adjustment, fuel system, power unit, lower unit, bracket unit, electrical system, and trouble analysis. The general information chapter discusses identification, safety practices, special tools, measuring tools, and removal/installation tools. It provides guidance on safe work practices, the importance of using the proper tools, and cleaning/lubricating parts during disassembly and assembly.
Massey Ferguson MF2625 TRACTOR - MADE IN INDIA FOR MEXICO, SOUTH AMERICA, AUS...ufjjsejkkemmd
This document contains parts lists and technical specifications for the engine, fuel system, and exhaust system of a Massey Ferguson 2625 tractor made in India for markets in Mexico, South America, Australia, and New Zealand. It includes lists of parts for the engine block, cylinder head, crankshaft, pistons, valves, and other internal engine components along with part numbers and quantities of each part. The document provides specifications for the engine depending on whether it has a rotary fuel pump or inline fuel injection pump.
Massey Ferguson MF2620 TRACTOR (MADE IN INDIA FOR TURKEY) Parts Catalogue Manualufjjsejkkemmd
This is the Highly Detailed factory Parts manual for theMASSEY FERGUSON MF2620 TRACTOR, this Parts Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.MASSEY FERGUSON MF2620 TRACTOR Parts Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this Parts manual is an inexpensive way to keep your vehicle working properly.
Parts Manual Covers:
Engine and Equipment
Clutch
Transmission
Rear Axle
Linkage
PTO-Drive Mechanism
Front Axle
Hydraulics
Electric Equipment and Instrument
Electronic Equipment
Sheet Metal
And more...
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveMASSEY FERGUSON MF2620 TRACTOR Parts Manual.
Thanks for visiting!
Massey ferguson mf 393 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document contains parts listings and technical specifications for engine components of a Massey Ferguson MF 393 tractor. It includes lists of parts for the engine assembly, short engine, cylinder block, crankshaft, pistons and connecting rods, and cylinder head. Each item listed includes the part number, quantity, description, and additional technical comments. The purpose is to provide detailed reference information for maintenance and repair of the MF 393 tractor engine.
Massey ferguson mf 363 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document provides parts information for repairing the engine of a Massey Ferguson 363 tractor. It includes 5 pages describing parts for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and other engine components. The document lists part numbers, quantities, descriptions and other details for over 100 individual engine parts.
Massey ferguson mf 284 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document provides a parts list for a Massey Ferguson MF 284 tractor engine cylinder head and cover. It includes 58 items such as cylinder head kits, valves, springs, seals, bolts, plates, guides, and covers. Each part is listed with its number, quantity, description, and any relevant comments on application or specifications. The parts are for both standard and metric-sized engines in the MF 284 tractor model 3310602.
Massey ferguson mf 275 tractor (fr) service parts catalogue manual (part numb...ufjjsejkkemmd
This document provides a parts list for an MF 275 tractor engine. It includes 24 items related to the engine and accessories with part numbers and descriptions. It also includes sections on the cylinder block, crankshaft, cylinder head, cylinder head cover, and air induction system with additional part numbers and descriptions for replacement parts.
Massey ferguson mf 273 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document provides a parts list and technical specifications for a Massey Ferguson MF 273 tractor. It includes over 50 individual parts listed with part numbers, quantities, descriptions, and other technical details. The document covers major systems of the tractor such as the cylinder block, crankshaft, cylinder head, rocker arm, timing gear, and lubricating oil system.
Massey ferguson 6455 tractor (tier 3) service parts catalogue manual (part nu...ufjjsejkkemmd
This document provides parts information for the engine and equipment on a Massey Ferguson 6455 Tractor (Tier 3) with serial number 3906155. It includes a list of 33 items with descriptions of engine parts like the cylinder block, crankshaft, pistons, cylinder head, and other components. It also provides part numbers, quantities, and additional part options or notes for many of the listed items.
John deere 17 zts compact excavator service repair technical manual (tm1897)ufjjsejkkemmd
This document provides instructions for removing and installing a steel track on an excavator. It describes removing the track master pin, using blocks to support the machine and track during removal. It also includes cautions for potential injuries from machine movement and the weight of track components. Installation involves positioning the track on the sprocket and turning it to pull the track across the frame.
The document provides instructions for servicing components of an excavator engine, including disassembling and assembling the exhaust manifold, fuel transfer pump, governor, and other parts. The multi-step instructions describe removing and installing parts like bolts, gaskets, valves, springs, and housings. Photos illustrate the component locations and tooling used.
The document provides instructions for servicing components of an excavator engine, including disassembling and assembling the exhaust manifold, fuel transfer pump, governor, and other parts. The multi-step instructions describe removing and installing components like bolts, gaskets, valves, springs, and housings. Photos supplement the text instructions to aid with the servicing process.
Caterpillar cat 320 c excavator (prefix jpl) service repair manual (jpl00001 ...ufjjsejkkemmd
This document provides instructions for removing and installing track components on a 320C excavator. The procedures describe how to:
1. Release tension on the track and remove the track carrier roller by loosening a relief valve, bolts, and lifting the track assembly off with a hydraulic jack.
2. Install the track carrier roller by positioning it in the mounting bracket, adjusting its position, and tightening bolts before lowering the track assembly onto it.
3. Remove the track roller by releasing track tension, loosening bolts, and lifting the roller and track guide off with lifting forks.
4. Install the track roller and guide by cleaning mounting surfaces, positioning components with lifting forks, and installing and tight
Caterpillar cat 320 c excavator (prefix ega) service repair manual (ega00001 ...ufjjsejkkemmd
This document provides instructions for disassembling and assembling the travel motor on a 320C excavator. It includes 28 steps for disassembly and 27 steps for assembly. Key steps include removing the piston motor, traction control valve, various seals, bearings, and internal components. Assembly involves installing these parts in reverse order and adjusting shims to ensure the output shaft meets torque and rotation requirements during checks. Proper cleaning, lubrication, and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling the recoil spring assembly of a 320 Excavator. It describes:
1) Using a specialized recoil spring bench tool and hydraulic cylinder to safely compress the recoil spring assembly and remove/install parts.
2) The 16 step procedure for disassembly, including removing the retaining nut and separating spring components.
3) The 14 step procedure for assembly, including verifying spring length, applying lubricant, and reinstalling retaining components.
Safety is emphasized, as the spring exerts several tons of force and parts could come apart with injury. Precise tool setup and slow, careful compression/release of the spring is required.
Caterpillar cat 246 b skid steer loader (prefix pat) service repair manual (p...ufjjsejkkemmd
The document provides instructions for disassembling and assembling the piston motor of a 246B Skid Steer Loader. It lists 22 steps for disassembly, requiring various tools, and 20 steps for assembly. Safety warnings are included to take precautions when removing or installing parts under spring tension. Pictures accompany each step to illustrate the procedure.
This document provides instructions for disassembling the piston pump of a Caterpillar 242B3 Skid Steer Loader. It lists over 70 steps and required tools to remove components like fittings, springs, seals, plates, pins, bearings and shafts. Markings should be made on several parts for proper reassembly. Measurements are to be taken of component distances and orientations noted. Safety precautions are described for releasing stored spring energy.
This document provides instructions for removing and installing the engine oil pump on a 242B2 Skid Steer Loader powered by a 3024C engine. The removal procedure involves removing the front housing, idler gear components, inner rotor, thrust washer and suction pipe. The installation procedure outlines installing these components in reverse order and adjusting end play clearance with a feeler gauge.
Case ih maxxum cvt 110 international region f4 dfe413ca tractor service repai...ufjjsejkkemmd
This document provides a service manual for MAXXUM tractors. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, and electrical systems. The document provides detailed instructions and specifications for servicing and repairing components of these systems.
Case ih maxxum 140 multicontroller ep international region f4 dfe6132a tracto...ufjjsejkkemmd
This document is a service manual that provides part numbers and product information for MAXXUM tractors including the EP, Multicontroller EP, and CVT models between 110-140 horsepower. It includes an introduction and table of contents that lists the various systems covered in the manual such as the engine, transmission, hydraulics, steering, wheels, and electrical systems. The document provides service information to repair and maintain components of the MAXXUM tractors.
Case ih maxxum 115 multicontroller ep europe f4 dfe613fa service repair manualufjjsejkkemmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM 110-140 Multicontroller EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering the engine, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulic systems, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each section provides maintenance and repair information for the corresponding component or system of the tractors.
Case ih jx1070 u tractor service repair manualufjjsejkkemmd
This document is a service manual for tractor models JX1070U, JX1080U, JX1090U, and JX1100U. It contains sections on general guidelines, the engine, clutch, transmission, drive lines, mechanical components, hydraulics, steering, axles, electrical systems, and more. Each section provides specifications, diagrams, maintenance and repair instructions, and other technical information for the systems covered.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Massey Ferguson MF2620 TRACTOR (MADE IN INDIA FOR TURKEY) Parts Catalogue Manualufjjsejkkemmd
This is the Highly Detailed factory Parts manual for theMASSEY FERGUSON MF2620 TRACTOR, this Parts Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.MASSEY FERGUSON MF2620 TRACTOR Parts Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this Parts manual is an inexpensive way to keep your vehicle working properly.
Parts Manual Covers:
Engine and Equipment
Clutch
Transmission
Rear Axle
Linkage
PTO-Drive Mechanism
Front Axle
Hydraulics
Electric Equipment and Instrument
Electronic Equipment
Sheet Metal
And more...
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveMASSEY FERGUSON MF2620 TRACTOR Parts Manual.
Thanks for visiting!
Massey ferguson mf 393 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document contains parts listings and technical specifications for engine components of a Massey Ferguson MF 393 tractor. It includes lists of parts for the engine assembly, short engine, cylinder block, crankshaft, pistons and connecting rods, and cylinder head. Each item listed includes the part number, quantity, description, and additional technical comments. The purpose is to provide detailed reference information for maintenance and repair of the MF 393 tractor engine.
Massey ferguson mf 363 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document provides parts information for repairing the engine of a Massey Ferguson 363 tractor. It includes 5 pages describing parts for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and other engine components. The document lists part numbers, quantities, descriptions and other details for over 100 individual engine parts.
Massey ferguson mf 284 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document provides a parts list for a Massey Ferguson MF 284 tractor engine cylinder head and cover. It includes 58 items such as cylinder head kits, valves, springs, seals, bolts, plates, guides, and covers. Each part is listed with its number, quantity, description, and any relevant comments on application or specifications. The parts are for both standard and metric-sized engines in the MF 284 tractor model 3310602.
Massey ferguson mf 275 tractor (fr) service parts catalogue manual (part numb...ufjjsejkkemmd
This document provides a parts list for an MF 275 tractor engine. It includes 24 items related to the engine and accessories with part numbers and descriptions. It also includes sections on the cylinder block, crankshaft, cylinder head, cylinder head cover, and air induction system with additional part numbers and descriptions for replacement parts.
Massey ferguson mf 273 tractor service parts catalogue manual (part number 3...ufjjsejkkemmd
This document provides a parts list and technical specifications for a Massey Ferguson MF 273 tractor. It includes over 50 individual parts listed with part numbers, quantities, descriptions, and other technical details. The document covers major systems of the tractor such as the cylinder block, crankshaft, cylinder head, rocker arm, timing gear, and lubricating oil system.
Massey ferguson 6455 tractor (tier 3) service parts catalogue manual (part nu...ufjjsejkkemmd
This document provides parts information for the engine and equipment on a Massey Ferguson 6455 Tractor (Tier 3) with serial number 3906155. It includes a list of 33 items with descriptions of engine parts like the cylinder block, crankshaft, pistons, cylinder head, and other components. It also provides part numbers, quantities, and additional part options or notes for many of the listed items.
John deere 17 zts compact excavator service repair technical manual (tm1897)ufjjsejkkemmd
This document provides instructions for removing and installing a steel track on an excavator. It describes removing the track master pin, using blocks to support the machine and track during removal. It also includes cautions for potential injuries from machine movement and the weight of track components. Installation involves positioning the track on the sprocket and turning it to pull the track across the frame.
The document provides instructions for servicing components of an excavator engine, including disassembling and assembling the exhaust manifold, fuel transfer pump, governor, and other parts. The multi-step instructions describe removing and installing parts like bolts, gaskets, valves, springs, and housings. Photos illustrate the component locations and tooling used.
The document provides instructions for servicing components of an excavator engine, including disassembling and assembling the exhaust manifold, fuel transfer pump, governor, and other parts. The multi-step instructions describe removing and installing components like bolts, gaskets, valves, springs, and housings. Photos supplement the text instructions to aid with the servicing process.
Caterpillar cat 320 c excavator (prefix jpl) service repair manual (jpl00001 ...ufjjsejkkemmd
This document provides instructions for removing and installing track components on a 320C excavator. The procedures describe how to:
1. Release tension on the track and remove the track carrier roller by loosening a relief valve, bolts, and lifting the track assembly off with a hydraulic jack.
2. Install the track carrier roller by positioning it in the mounting bracket, adjusting its position, and tightening bolts before lowering the track assembly onto it.
3. Remove the track roller by releasing track tension, loosening bolts, and lifting the roller and track guide off with lifting forks.
4. Install the track roller and guide by cleaning mounting surfaces, positioning components with lifting forks, and installing and tight
Caterpillar cat 320 c excavator (prefix ega) service repair manual (ega00001 ...ufjjsejkkemmd
This document provides instructions for disassembling and assembling the travel motor on a 320C excavator. It includes 28 steps for disassembly and 27 steps for assembly. Key steps include removing the piston motor, traction control valve, various seals, bearings, and internal components. Assembly involves installing these parts in reverse order and adjusting shims to ensure the output shaft meets torque and rotation requirements during checks. Proper cleaning, lubrication, and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling the recoil spring assembly of a 320 Excavator. It describes:
1) Using a specialized recoil spring bench tool and hydraulic cylinder to safely compress the recoil spring assembly and remove/install parts.
2) The 16 step procedure for disassembly, including removing the retaining nut and separating spring components.
3) The 14 step procedure for assembly, including verifying spring length, applying lubricant, and reinstalling retaining components.
Safety is emphasized, as the spring exerts several tons of force and parts could come apart with injury. Precise tool setup and slow, careful compression/release of the spring is required.
Caterpillar cat 246 b skid steer loader (prefix pat) service repair manual (p...ufjjsejkkemmd
The document provides instructions for disassembling and assembling the piston motor of a 246B Skid Steer Loader. It lists 22 steps for disassembly, requiring various tools, and 20 steps for assembly. Safety warnings are included to take precautions when removing or installing parts under spring tension. Pictures accompany each step to illustrate the procedure.
This document provides instructions for disassembling the piston pump of a Caterpillar 242B3 Skid Steer Loader. It lists over 70 steps and required tools to remove components like fittings, springs, seals, plates, pins, bearings and shafts. Markings should be made on several parts for proper reassembly. Measurements are to be taken of component distances and orientations noted. Safety precautions are described for releasing stored spring energy.
This document provides instructions for removing and installing the engine oil pump on a 242B2 Skid Steer Loader powered by a 3024C engine. The removal procedure involves removing the front housing, idler gear components, inner rotor, thrust washer and suction pipe. The installation procedure outlines installing these components in reverse order and adjusting end play clearance with a feeler gauge.
Case ih maxxum cvt 110 international region f4 dfe413ca tractor service repai...ufjjsejkkemmd
This document provides a service manual for MAXXUM tractors. It includes sections on the engine, clutch, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, and electrical systems. The document provides detailed instructions and specifications for servicing and repairing components of these systems.
Case ih maxxum 140 multicontroller ep international region f4 dfe6132a tracto...ufjjsejkkemmd
This document is a service manual that provides part numbers and product information for MAXXUM tractors including the EP, Multicontroller EP, and CVT models between 110-140 horsepower. It includes an introduction and table of contents that lists the various systems covered in the manual such as the engine, transmission, hydraulics, steering, wheels, and electrical systems. The document provides service information to repair and maintain components of the MAXXUM tractors.
Case ih maxxum 115 multicontroller ep europe f4 dfe613fa service repair manualufjjsejkkemmd
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM 110-140 Multicontroller EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering the engine, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulic systems, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each section provides maintenance and repair information for the corresponding component or system of the tractors.
Case ih jx1070 u tractor service repair manualufjjsejkkemmd
This document is a service manual for tractor models JX1070U, JX1080U, JX1090U, and JX1100U. It contains sections on general guidelines, the engine, clutch, transmission, drive lines, mechanical components, hydraulics, steering, axles, electrical systems, and more. Each section provides specifications, diagrams, maintenance and repair instructions, and other technical information for the systems covered.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Contents
INTRODUCTION
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS A
PRIMARY HYDRAULIC POWER SYSTEM.............................................. A.10.A
PNEUMATIC SYSTEM ................................................................... A.20.A
ELECTRICAL POWER SYSTEM ........................................................ A.30.A
FAULT CODES ........................................................................... A.50.A
ENGINE AND PTO IN ................................................................... B
ENGINE .................................................................................. B.10.A
FUEL AND INJECTION SYSTEM........................................................ B.20.A
AIR INTAKE SYSTEM.................................................................... B.30.A
EXHAUST SYSTEM Emissions control .................................................. B.40.B
ENGINE COOLANT SYSTEM ........................................................... B.50.A
STARTING SYSTEM ..................................................................... B.80.A
TRANSMISSION, DRIVE AND PTO OUT........................................ C
TRANSMISSION Power Shuttle.......................................................... C.20.C
ADDITIONAL REDUCERS Mechanical Hi-Lo unit ....................................... C.30.E
AXLES, BRAKES AND STEERING................................................. D
FRONT AXLE ............................................................................ D.10.A
REAR AXLE .............................................................................. D.12.A
STEERING Mechanical .................................................................. D.20.B
STEERING Hydraulic..................................................................... D.20.C
SERVICE BRAKE Pneumatic ............................................................ D.30.E
FRAME AND CAB ........................................................................ E
FRAME Primary frame ................................................................... E.10.B
SHIELD................................................................................... E.20.A
USER PLATFORM ....................................................................... E.34.A
ENVIRONMENT CONTROL Heating, ventilation and air-conditioning................... E.40.D
FRAME POSITIONING ................................................................. F
84559771 18/01/2012
6. INTRODUCTION
Safety rules
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
CAUTION
Flying objects!
Wear eye protection. Do not strike steel parts with a steel hammer. Parts may break.
Failure to comply could result in minor or moderate injury.
C0024A
CAUTION
Flying debris!
Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using com-
pressed air.
Failure to comply could result in minor or moderate injury.
C0049A
WARNING
Crushing hazard!
Unit could fall if not properly supported. Follow jacking instructions provided for the unit. Use suitable
jack stands. Be sure to position them properly.
Failure to comply could result in death or serious injury.
W0919A
WARNING
Explosive gas!
Batteries emit explosive hydrogen gas and other fumes while charging. Ventilate the charging area.
Keep the battery away from sparks, open flames, and other ignition sources. Never charge a frozen
battery.
Failure to comply could result in death or serious injury.
W0005A
WARNING
Hazardous chemicals!
Battery electrolyte contains sulfuric acid. Contact with skin and eyes could result in severe irritation
and burns. Always wear splash-proof goggles and protective clothing (gloves and aprons). Wash
hands after handling.
Failure to comply could result in death or serious injury.
W0006A
WARNING
Inhalation hazard! Risk to operators and bystanders.
Avoid running the engine in confined areas. Make sure there is adequate ventilation at all times.
Failure to comply could result in death or serious injury.
W0156A
84559771 18/01/2012
3
7. INTRODUCTION
WARNING
Entanglement hazard!
Always keep hair and clothing away from moving parts. Do not wear loose clothing, jewelry, or other
items that could entangle with moving parts and/or levers.
Failure to comply could result in death or serious injury.
W0445A
WARNING
Escaping fluid!
Hydraulic fluid or diesel fuel leaking under pressure can penetrate the skin and cause infection or
other injury. To prevent personal injury: Relieve all pressure before disconnecting fluid lines or per-
forming work on the hydraulic system. Before applying pressure, make sure all connections are tight
and all components are in good condition. Never use your hand to check for suspected leaks under
pressure. Use a piece of cardboard or wood for this purpose. If injured by leaking fluid, see your
doctor immediately.
Failure to comply could result in death or serious injury.
W0178A
DANGER
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply will result in death or serious injury.
D0076A
WARNING
Electrocution hazard!
Keep the area used for servicing the machine clean and dry. Wet or oily floors are slippery. Wet spots
can be dangerous when working with electrical equipment. Be sure all electrical outlets and tools are
properly grounded.
Failure to comply could result in death or serious injury.
W0355A
WARNING
Personal Protective Equipment (PPE) required.
When assembling, operating, or servicing the machine, wear protective clothing and PPE necessary
for the particular procedure. Some PPE that may be necessary includes protective shoes, eye and/or
face protection, hard hat, heavy gloves, filter mask, and hearing protection.
Failure to comply could result in death or serious injury.
W0353A
84559771 18/01/2012
4
8. INTRODUCTION
Torque
Decimal hardware
Grade 5 bolts, nuts and studs
Size Nm lb in/lb ft
1/4 in 12 - 15 Nm 108 - 132 lb in
5/16 in 23 - 28 Nm 204 - 252 lb in
3/8 in 48 - 57 Nm 420 - 504 lb in
7/16 in 73 - 87 Nm 54 - 64 lb ft
1/2 in 109 - 130 Nm 80 - 96 lb ft
9/16 in 149 - 179 Nm 110 - 132 lb ft
5/8 in 203 - 244 Nm 150 - 180 lb ft
3/4 in 366 - 439 Nm 270 - 324 lb ft
7/8 in 542 - 651 Nm 400 - 480 lb ft
1 in 787 - 944 Nm 580 - 696 lb ft
1-1/8 in 1085 - 1193 Nm 800 - 880 lb ft
1-1/4 in 1519 - 1681 Nm 1120 - 1240 lb ft
1-3/8 in 1980 - 2278 Nm 1460 - 1680 lb ft
1-1/2 in 2631 - 2983 Nm 1940 - 2200 lb ft
Grade 8 bolts, nuts and studs
Size Nm lb in/lb ft
1/4 in 16 - 20 Nm 144 - 180 lb in
5/16 in 33 - 39 Nm 288 - 348 lb in
3/8 in 61 - 73 Nm 540 - 648 lb in
7/16 in 95 - 114 Nm 70 - 84 lb ft
1/2 in 149 - 179 Nm 110 - 132 lb ft
9/16 in 217 - 260 Nm 160 - 192 lb ft
5/8 in 298 - 358 Nm 220 - 264 lb ft
3/4 in 515 - 618 Nm 380 - 456 lb ft
7/8 in 814 - 976 Nm 600 - 720 lb ft
1 in 1220 - 1465 Nm 900 - 1080 lb ft
1-1/8 in 1736 - 1953 Nm 1280 - 1440 lb ft
1-1/4 in 2468 - 2712 Nm 1820 - 2000 lb ft
1-3/8 in 3227 - 3688 Nm 2380 - 2720 lb ft
1-1/2 in 4285 - 4827 Nm 3160 - 3560 lb ft
NOTE: Use thick nuts with Grade 8 bolts.
Metric hardware
Grade 8.8 bolts, nuts and studs
Size Nm lb in/lb ft
4 mm 3 - 4 Nm 24 - 36 lb in
5 mm 7 - 8 Nm 60 - 72 lb in
6 mm 11 - 12 Nm 96 - 108 lb in
8 mm 26 - 31 Nm 228 - 276 lb in
10 mm 52 - 61 Nm 456 - 540 lb in
12 mm 90 - 107 Nm 66 - 79 lb ft
14 mm 144 - 172 Nm 106 - 127 lb ft
16 mm 217 - 271 Nm 160 - 200 lb ft
20 mm 434 - 515 Nm 320 - 380 lb ft
24 mm 675 - 815 Nm 500 - 600 lb ft
30 mm 1250 - 1500 Nm 920 - 1100 lb ft
36 mm 2175 - 2600 Nm 1600 - 1950 lb ft
84559771 18/01/2012
5
9. INTRODUCTION
Grade 10.9 bolts, nuts and studs
Size Nm lb in/lb ft
4 mm 4 - 5 Nm 36 - 48 lb in
5 mm 9 - 11 Nm 84 - 96 lb in
6 mm 15 - 18 Nm 132 - 156 lb in
8 mm 37 - 43 Nm 324 - 384 lb in
10 mm 73 - 87 Nm 54 - 64 lb ft
12 mm 125 - 150 Nm 93 - 112 lb ft
14 mm 200 - 245 Nm 149 - 179 lb ft
16 mm 310 - 380 Nm 230 - 280 lb ft
20 mm 610 - 730 Nm 450 - 540 lb ft
24 mm 1050 - 1275 Nm 780 - 940 lb ft
30 mm 2000 - 2400 Nm 1470 - 1770 lb ft
36 mm 3500 - 4200 Nm 2580 - 3090 lb ft
Grade 12.9 bolts, nuts and studs
Size Nm lb in/lb ft
Typically the torque values specified for grade 10.9 hardware can be used satisfactorily on grade 12.9 hardware.
Steel hydraulic fittings
37° flare fitting
Tube outside diameter/Hose inside
diameter
mm inch
Thread size Nm lb in/lb ft
6.4 mm 1/4 in 7/16-20 in 8 - 16 Nm 72 - 144 lb in
7.9 mm 5/16 in 1/2-20 in 11 - 22 Nm 96 - 192 lb in
9.5 mm 3/8 in 9/16-18 in 14 - 34 Nm 120 - 300 lb in
12.7 mm 1/2 in 3/4-16 in 20 - 57 Nm 180 - 504 lb in
15.9 mm 5/6 in 7/8-14 in 34 - 79 Nm 300 - 696 lb in
19.0 mm 3/4 in 1-1/16-12 in 54 - 108 Nm 40 - 80 lb ft
22.2 mm 7/8 in 1-3/16-12 in 81 - 135 Nm 60 - 100 lb ft
25.4 mm 1 in 1-5/16-12 in 102 - 158 Nm 75 - 117 lb ft
31.8 mm 1-1/4 in 1-5/8-12 in 169 - 223 Nm 125 - 165 lb ft
38.1 mm 1-1/2 in 1-7/8-12 in 285 - 338 Nm 210 - 250 lb ft
Straight threads with O-ring
Tube outside diameter/Hose inside
diameter
mm inch
Thread size Nm lb in/lb ft
6.4 mm 1/4 in 7/16-20 in 16 - 26 Nm 144 - 228 lb in
7.9 mm 5/16 in 1/2-20 in 22 - 34 Nm 192 - 300 lb in
9.5 mm 3/8 in 9/16-18 in 34 - 54 Nm 300 - 480 lb in
12.7 mm 1/2 in 3/4-16 in 57 - 91 Nm 540 - 804 lb in
15.9 mm 5/6 in 7/8-14 in 79 - 124 Nm 58 - 92 lb ft
19.0 mm 3/4 in 1-1/16-12 in 108 - 174 Nm 80 - 128 lb ft
22.2 mm 7/8 in 1-3/16-12 in 136 - 216 Nm 100 - 160 lb ft
25.4 mm 1 in 1-5/16-12 in 159 - 253 Nm 117 - 187 lb ft
31.8 mm 1-1/4 in 1-5/8-12 in 224 - 357 Nm 165 - 264 lb ft
38.1 mm 1-1/2 in 1-7/8-12 in 339 - 542 Nm 250 - 400 lb ft
Split flange mounting bolts
Size Nm lb in/lb ft
5/16-18 in 20 - 27 Nm 180 - 240 lb in
3/8-16 in 27 - 34 Nm 240 - 300 lb in
7/16-14 in 47 - 61 Nm 420 - 540 lb in
1/2-13 in 74 - 88 Nm 55 - 65 lb ft
84559771 18/01/2012
6
10. INTRODUCTION
Size Nm lb in/lb ft
5/8-11 in 190 - 203 Nm 140 - 150 lb ft
O-ring face seal end O-ring boss end fitting or lock nut
Tube outside diameterNominal
SAE dash
size
mm in
Thread size Nm lb in/lb ft Thread size Nm lb in/lb ft
-4 6.4 mm 1/4 in 9/16-18 in 14 - 16 Nm 120 - 144
lb in
7/16-20 in 23 - 27 Nm 204 - 240
lb in
-6 9.5 mm 3/8 in 11/16-16 in 24 - 27 Nm 216 - 240
lb in
9/16-18 in 34 - 41 Nm 300 - 360
lb in
-8 12.7 mm 1/2 in 13/16-16 in 43 - 54 Nm 384 - 480
lb in
3/4-16 in 61 - 68 Nm 540 - 600
lb in
-10 15.9 mm 5/8 in 1-14 in 62 - 76 Nm 552 - 672
lb in
7/8-14 in 81 - 88 Nm 60 - 65 lb ft
-12 19.0 mm 3/4 in 1-3/16-12
in
90 - 110
Nm
65 - 80 lb ft 1-1/16-12
in
115 - 122
Nm
85 - 90 lb ft
-14 22.2 mm 7/8 in 1-3/16-12
in
90 - 110
Nm
65 - 80 lb ft 1-13/16-12
in
129 - 136
Nm
95 - 100 lb
ft
-16 25.41 mm 1.0 in 1-7/16-12
in
125 - 140
Nm
92 - 105 lb
ft
1-5/16-12
in
156 - 169
Nm
115 - 125 lb
ft
-20 31.8 mm 1-1/4 in 1-11/16-12
in
170 - 190
Nm
125 - 140
lb ft
1`-5/6-12 in 201 - 217
Nm
150 - 160
lb ft
-24 38.1 mm 1-1/2 in 2-12 in 200 - 254
Nm
150 - 180
lb ft
1-7/8-12 in 258 - 271
Nm
190 - 200
lb ft
84559771 18/01/2012
7
11. INTRODUCTION
Capacities - 3 wheel models
Titan 3030, Titan 3530
Engine
Oil type CASE IH AKCELA NO. 1™ ENGINE OIL
Oil exchange capacity with filter (approximate.) 25 l (6.6 US gal)
Cooling system
Coolant type CASE IH AKCELA PREMIUM ANTI-FREEZE 50-50
water and ethylene glycol mix
Radiator capacity 52 l (13.75 US gal)
Hydraulic system
Oil type CASE IH AKCELA HY-TRAN® ULTRA™ HYDRAULIC
TRANSMISSION OIL
Tank capacity (chassis only) 114 l (30 US gal)
Axle (rear)
Oil type CASE IH AKCELA GEAR 135 H EP 85W-140
Differential 17 l (4.5 US gal)
Planetary wheel ends (each 3.8 l (1 US gal)
Transmission
Oil type Transynd®
Capacity 21 l (5.5 US gal)
Auxiliary transmission
Oil type CASE IH AKCELA HY-TRAN® ULTRA™ HYDRAULIC
TRANSMISSION OIL
Capacity 4.28 l (1.13 US gal)
Two speed shifter
Oil type Air tool oil
Capacity 30 ml (1 US fl oz)
Air conditioning system
Refrigerant type R134A
Refrigerant capacity 1.86 kg (4.1 lb)
Diesel Exhaust Fluid (DEF)/AdBlue® tank capacity
Capacity 108 l (28.5 US gal)
Diesel fuel tank
Capacity 568 l (150 US gal)
84559771 18/01/2012
8
12. INTRODUCTION
Capacities - 4 wheel models
Titan 4030, Titan 4530
Engine
Oil type CASE IH AKCELA NO. 1™ ENGINE OIL
Oil exchange capacity with filter (approximate.) 25 l (6.6 US gal)
Cooling system
Coolant type CASE IH AKCELA PREMIUM ANTI-FREEZE 50-50
water and ethylene glycol mix
Radiator capacity 52 l (13.75 US gal)
Hydraulic system
Oil type CASE IH AKCELA HY-TRAN® ULTRA™ HYDRAULIC
TRANSMISSION OIL
Tank capacity (chassis only) 114 l (30 US gal)
Axle (rear)
Oil type CASE IH AKCELA GEAR 135 H EP 85W-140
Differential 17 l (4.5 US gal)
Planetary wheel ends (each 3.8 l (1 US gal)
Axle (front)
Oil type CASE IH AKCELA GEAR 135 H EP 80W-90
Capacity 1.18 l (1.25 US qt)
Transmission
Oil type Transynd®
Capacity 21 l (5.5 US gal)
Auxiliary transmission
Oil type CASE IH AKCELA HY-TRAN® ULTRA™ HYDRAULIC
TRANSMISSION OIL
Capacity 4.28 l (1.13 US gal)
Two speed shifter
Oil type Air tool oil
Capacity 30 ml (1 US fl oz)
Air conditioning system
Refrigerant type R134A
Refrigerant capacity 1.86 kg (4.1 lb)
Diesel Exhaust Fluid (DEF)/AdBlue® tank
Capacity 108 l (28.5 US gal)
Diesel fuel tank
Capacity 568 l (150 US gal)
84559771 18/01/2012
9
13. INTRODUCTION
General specification - 3 wheel models
Titan 3030, Titan 3530
Item Titan 3030 Specification
Engine 8.7 l (530 in³) 330 Hp
Case IH Cursor Emission level (tier) 4A
Transmission Allison 3000 RDS 6 speed automatic
Rear Axle Axle Tech PRC 674 2 speed with wheel end planetary
Front Axle 115 mm (4.53 in) solid shaft, 70 mm (2.76 in) axle bearings
Frame 12 x 4 x 0.3125 inches HSLA cold formed steel main frame with high
strength reinforcement plates.
Wheelbase 6.8 m (268 in)
Cab to Axle 2.89 m (114 in)
Cab to end of frame 3.78 m (149 in)
Overall length 8.59 m (338 in)
Overall width 3.5 m (138 in)
Overall height 3.62 m (142.5 in) with 66/66 tires
Dimensions
Weight 9911 kg (21850 lb) (estimate)
Front axle (static) 6350 kg (14000 lb)
Rear Axle (static) 15422 kg (34000 lb)
Chassis vehicle rated capacity
Total (static) 21772 kg (48000 lb)
Front Air ( 36 cubic inch chamber) over
hydraulic applied 711 mm (28 in) disc
brake w/ dual piston floating caliper
Rear Air applied 16.5 x 5 inch with 36 cubic
inch chambers
Brakes
Park Spring applied, air release
Front Firestone: 66 x 43-25 bias, 16 ply
1050/50R25 radial
Goodyear: 1000/50R25 radial
Michelin: 1000/50R25 radial
Tires
Rear Firestone: 66 x 43-25 bias, 16 ply
1050/50R25 radial
Goodyear: 1000/50R25 radial
Michelin: 1000/50R25 radial
Steering Hydraulic with flow control pump and load sensing dual displacement
steering valve.
Paint Roof, bottom and side panels, hood and frame: Two part urethane. Cab
metal parts: Thermal set acrylic.
84559771 18/01/2012
10
14. INTRODUCTION
Item Titan 3530 Specification
Engine 8.7 l (530 in³) 400 Hp
Case IH Cursor Emission level (tier) 4A
Transmission Allison 3000 RDS 6 speed automatic
Rear Axle Axle Tech PRC 674 2 speed with wheel end planetary
Front Axle 115 mm (4.53 in) solid shaft, 70 mm (2.76 in) axle bearings
Frame 12 x 4 x 0.3125 inches HSLA cold formed steel main frame with high
strength reinforcement plates.
Wheelbase 6.8 m (268 in)
Cab to Axle 2.89 m (114 in)
Cab to end of frame 3.78 m (149 in)
Overall length 8.59 m (338 in)
Overall width 3.5 m (138 in)
Overall height 3.62 m (142.5 in) with 66/66 tires
Dimensions
Weight 10369 kg (22860 lb) (estimate)
Front axle (static) 6350 kg (14000 lb)
Rear Axle (static) 15422 kg (34000 lb)
Chassis vehicle rated capacity
Total (static) 21772 kg (48000 lb)
Front Air ( 36 cubic inch chamber) over
hydraulic applied 711 mm (28 in) disc
brake w/ dual piston floating caliper
Rear Air applied 16.5 x 5 inch with 36 cubic
inch chambers
Brakes
Park Spring applied, air release
Front Firestone: 66 x 43-25 bias, 16 ply
1050/50R25 radial
Goodyear: 1000/50R25 radial
Michelin: 1000/50R25 radial
Tires
Rear Firestone: 66 x 43-25 bias, 16 ply
1050/50R25 radial, 73 x 44.00–32
bias, 16 ply
Goodyear: 1000/50R25 radial,
1050/50R32 radial
Michelin: 1000/50R25 radial,
1050/50R32 radial
Steering Hydraulic with flow control pump and load sensing dual displacement
steering valve.
Paint Roof, bottom and side panels, hood and frame: Two part urethane. Cab
metal parts: Thermal set acrylic.
84559771 18/01/2012
11
15. INTRODUCTION
General specification - 4 wheel models
Titan 4030, Titan 4530
Item Titan 4030 Specification
Engine 8.7 l (530 in³) 330 Hp
Case IH Cursor Emission level (tier) 4A
Transmission Allison 3000 RDS 6 speed automatic
Rear Axle Axle Tech PRC 674 2 speed with wheel end planetary
Front Axle Axle Tech MS-25, 162 mm (6.375 in) tubular drop axle
Frame 10 in x 4 in x 0.375 in rectangular tube
Wheelbase 4.57 m (180 in)
Cab to Axle 2.89 m (114 in)
Cab to end of frame 3.78 m (149 in)
Overall length 7.70 m (303 in)
Overall width 3.5 m (138 in)
Overall height 3.57 m (140.5 in) with 48/66 tires
Dimensions
Weight 9430 kg (20790 lb) (estimate)
Front axle (static) 7257 kg (16000 lb)
Rear Axle (static) 15422 kg (34000 lb)
Chassis vehicle rated capacity
Total (static) 22680 kg (50000 lb)
Front Air applied 419 mm (16.5 in) x
152 mm (6 in) with 30 cubic inch
chambers
Rear Air applied 419 mm (16.5 in) x
127 mm (5 in) with 36 cubic inch
chambers
Brakes
Park Spring applied, air release
Front Alliance: 750/45R26.5
Goodyear: 54 x 31R26 radial
Michelin 750/50R26
Tires
Rear Firestone: 66 x 43-25 bias, 16 ply
1050/50R25 bias
Goodyear: 1000/50R25 radial
Michelin: 1000/50R25 radial
Steering Hydraulic with flow control pump and load sensing dual displacement
steering valve.
Paint Roof, bottom and side panels, hood and frame: Two part urethane. Cab
metal parts: Thermal set acrylic.
84559771 18/01/2012
12
16. INTRODUCTION
Item Titan 4530 Specification
Engine 8.7 l (530 in³) 400 Hp
Case IH Cursor Emission level (tier) 4A
Transmission Allison 3000 RDS 6 speed automatic
Rear Axle Axle Tech PRC 674 2 speed with wheel end planetary
Front Axle Axle Tech MS-25, 162 mm (6.375 in) tubular drop axle
Frame 10 in x 4 in x 0.375 in rectangular tube
Wheelbase 4.57 m (180 in)
Cab to Axle 2.89 m (114 in)
Cab to end of frame 3.78 m (149 in)
Overall length 7.70 m (303 in)
Overall width 3.5 m (138 in)
Overall height 3.63 m (143 in) with 54/73 tires
Dimensions
Weight 9888 kg (21800 lb) (estimate)
Front axle (static) 7257 kg (16000 lb)
Rear Axle (static) 15422 kg (34000 lb)
Chassis vehicle rated capacity
Total (static) 22680 kg (50000 lb)
Front Air applied 419 mm (16.5 in) x
152 mm (6 in) with 30 cubic inch
chambers
Rear Air applied 419 mm (16.5 in) x
127 mm (5 in) with 36 cubic inch
chambers
Brakes
Park Spring applied, air release
Front Alliance: 750/45R26.5
Goodyear: 54 x 31R26 radial
Michelin 750/50R26
Tires
Rear Firestone: 66 x 43-25 bias, 16 ply
1050/50R25 bias, 73 x 44.00 x 26
bias, 16 ply
Goodyear: 1000/50R25 radial,
1050/50R32 radial
Michelin: 1000/50R25 radial,
1050/50R32 radial
Steering Hydraulic with flow control pump and load sensing dual displacement
steering valve.
Paint Roof, bottom and side panels, hood and frame: Two part urethane. Cab
metal parts: Thermal set acrylic.
84559771 18/01/2012
13
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.