This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 370 to 620 that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, electrical systems, and the platform, cab, and bodywork. Safety information is provided throughout advising technicians to follow procedures carefully and use only approved parts when servicing components.
Case ih quadtrac 470 tier 4 b (final) tractor service repair manualfujsjezaqwfkskemm
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, frames and hitches, steering, wheels, tracks, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...fkjsekksmem
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block using bolts. Finally, it states to install the suction pipe, gasket, and support bracket if applicable.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Case ih quadtrac 470 tier 4 b (final) tractor service repair manualfujsjezaqwfkskemm
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, frames and hitches, steering, wheels, tracks, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...fkjsekksmem
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block using bolts. Finally, it states to install the suction pipe, gasket, and support bracket if applicable.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...fkjsekksmem
The document provides instructions for servicing the transmission of a 329D or 329D L excavator. It involves removing and disassembling the final drive, then cleaning and inspecting parts. Key steps include using various tools to remove gears, shafts, seals, and other components. Precise reassembly requires determining the correct shim thickness to preload bearings and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components on Caterpillar 320, 320L, and 320N track-type excavators, including:
1. Removing and installing inlet and exhaust valve seals from the engine cylinders.
2. Removing the engine oil filter base to access internal engine components.
3. Installing a new engine oil filter base and ensuring proper sealing.
4. Removing the engine oil cooler and associated mounting hardware.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
This document provides instructions for separating a track on a 320D LN excavator. It lists the required tools which include a chain, track block assembly, electric hydraulic pump group, hydraulic pressure gauge, pipe bushings, quick connect couplers, plugs, hoses, track press tool group, double acting cylinder, and track press rollover group. The procedure involves cleaning the exterior of the track thoroughly before disassembly to prevent dirt from entering the internal mechanism when the track is separated.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...fkjsekksmem
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...fkjsekksmem
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts and spacers. Inner and outer dust seals are installed in seal grooves on the swing gear and bearing.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 320 d l excavator (prefix kzf) service repair manual (kzf0000...fkjsekksmem
The document provides instructions for disassembling and assembling a final drive for excavator models 320D and 320D L. It describes 33 steps to disassemble the final drive components including removing bolts, shafts, gears, seals, and bearings. It then describes 32 steps for reassembling the final drive, applying sealant and lubricant, and installing components in reverse order using pressing and lifting tools. Precision is required to determine shim thickness for proper bearing preload.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...fkjsekksmem
This document provides instructions for disassembling and assembling the torque converter of a 725C articulated truck. The disassembly process involves removing over 40 individual parts from the torque converter including housings, gears, seals, bearings, and other components. Detailed illustrations accompany each step. The assembly section provides the reverse steps and notes on cleaning, inspecting, and lubricating parts during reassembly. Required tools are listed for both disassembly and assembly.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...fkjsekksmem
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...fkjsekksmem
The document provides instructions for servicing the transmission of a 329D or 329D L excavator. It involves removing and disassembling the final drive, then cleaning and inspecting parts. Key steps include using various tools to remove gears, shafts, seals, and other components. Precise reassembly requires determining the correct shim thickness to preload bearings and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout to prevent damage during reassembly.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components on Caterpillar 320, 320L, and 320N track-type excavators, including:
1. Removing and installing inlet and exhaust valve seals from the engine cylinders.
2. Removing the engine oil filter base to access internal engine components.
3. Installing a new engine oil filter base and ensuring proper sealing.
4. Removing the engine oil cooler and associated mounting hardware.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
This document provides instructions for separating a track on a 320D LN excavator. It lists the required tools which include a chain, track block assembly, electric hydraulic pump group, hydraulic pressure gauge, pipe bushings, quick connect couplers, plugs, hoses, track press tool group, double acting cylinder, and track press rollover group. The procedure involves cleaning the exterior of the track thoroughly before disassembly to prevent dirt from entering the internal mechanism when the track is separated.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 320 d2 l excavator (prefix gba) service repair manual (gba000...fkjsekksmem
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
Caterpillar cat 320 d2 l excavator (prefix dnp) service repair manual (dnp000...fkjsekksmem
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts and spacers. Inner and outer dust seals are installed in seal grooves on the swing gear and bearing.
The document provides instructions for removing the fuel injector from a Caterpillar 320D2 excavator engine. It lists the required tools which include a fuel injector puller and capping kit. The procedure involves disconnecting fuel lines from the injector, plugging the injector, removing mounting bolts and clamps, and using a puller tool to remove the fuel injector from the engine.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 320 d ln excavator (prefix wbn) service repair manual (wbn000...fkjsekksmem
This document provides the procedure for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LN excavator with a C6.4 engine. It describes using special tools to compress the valve springs and rotate the crankshaft to position the piston for safe removal and installation of the springs. Proper cleaning and inspection of parts is emphasized to prevent damage and wear. The process involves removing keepers and other components to access the springs which must be replaced in matched pairs per cylinder.
Caterpillar cat 320 d l excavator (prefix kzf) service repair manual (kzf0000...fkjsekksmem
The document provides instructions for disassembling and assembling a final drive for excavator models 320D and 320D L. It describes 33 steps to disassemble the final drive components including removing bolts, shafts, gears, seals, and bearings. It then describes 32 steps for reassembling the final drive, applying sealant and lubricant, and installing components in reverse order using pressing and lifting tools. Precision is required to determine shim thickness for proper bearing preload.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...fkjsekksmem
This document provides instructions for disassembling and assembling the torque converter of a 725C articulated truck. The disassembly process involves removing over 40 individual parts from the torque converter including housings, gears, seals, bearings, and other components. Detailed illustrations accompany each step. The assembly section provides the reverse steps and notes on cleaning, inspecting, and lubricating parts during reassembly. Required tools are listed for both disassembly and assembly.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...fkjsekksmem
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Link Product / Engine
Product Market Product Engine
null NA model [ZEF300001 - ] North America F3HFE613D*B001
null NA model [ZEF300001 - ] North America F3DFE613J*B001
null NA scraper model [ZEF300001
- ]
North America F3DFE613J*B001
null NA model [ZEF300001 - ] North America F3DFE613G*B001
null NA scraper model [ZEF300001
- ]
North America F3DFE613G*B001
null NA model [ZEF300001 - ] North America F3DFE613F*B001
null NA model [ZEF300001 - ] North America F2CFE614A*B
null NA model [ZEF300001 - ] North America F3HFE613G*B001
null NA model [ZEF300001 - ] North America F3HFE613D*B001
null NA model [ZEF300001 - ] North America F3HFE613B*B001
null NA standard wheeled
[ZEF300001 - ]
North America F2CFE614A*B
null NA heavy duty wheeled
[ZEF300001 - ]
North America F2CFE614A*B
null NA heavy duty wheeled
[ZEF300001 - ]
North America F3HFE613G*B001
null NA heavy duty wheeled
[ZEF300001 - ]
North America F3HFE613D*B001
null NA Wheeled scraper
[ZEF300001 - ]
North America F3HFE613D*B001
null NA heavy duty wheeled
[ZEF300001 - ]
North America F3HFE613B*B001
null NA wheeled scraper
[ZEF300001 - ]
North America F3HFE613B*B001
null NA model [ZEF300001 - ] North America F3HFE613B*B001
null NA scraper model [ZEF300001
- ]
North America F3HFE613B*B001
null NA heavy duty wheeled
[ZEF300001 - ]
North America F3DFE613J*B001
null NA wheeled scraper
[ZEF300001 - ]
North America F3DFE613J*B001
null NA heavy duty wheeled
[ZEF300001 - ]
North America F3DFE613G*B001
null NA wheeled scraper
[ZEF300001 - ]
North America F3DFE613G*B001
null NA heavy duty wheeled
[ZEF300001 - ]
North America F3DFE613F*B001
null NA wheeled scraper
[ZEF300001 - ]
North America F3DFE613F*B001
47680525 06/03/2014
3. Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.216] Fuel tanks .......................................................................... 10.2
[10.202] Air cleaners and lines .............................................................. 10.3
[10.310] Aftercooler.......................................................................... 10.4
[10.400] Engine cooling system ............................................................. 10.5
[10.414] Fan and drive ...................................................................... 10.6
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ........................... 10.7
Transmission.............................................................................. 21
[21.113] Powershift transmission ............................................................ 21.1
[21.135] Powershift transmission external controls.......................................... 21.2
[21.145] Gearbox internal components...................................................... 21.3
[21.155] Powershift transmission internal components...................................... 21.4
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.310] Final drives ......................................................................... 25.3
[25.500] Front axle track yoke assembly .................................................... 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
[27.610] Rear axle track yoke assembly .................................................... 27.4
Power Take-Off (PTO)................................................................. 31
[31.104] Rear electro-hydraulic control...................................................... 31.1
47680525 06/03/2014
4. [31.110] One-speed rear Power Take-Off (PTO) ............................................ 31.2
[31.220] Gearbox ............................................................................ 31.3
Brakes and controls .................................................................... 33
[33.110] Parking brake or parking lock ...................................................... 33.1
[33.202] Hydraulic service brakes ........................................................... 33.2
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.102] Pump control valves................................................................ 35.2
[35.105] Charge pump....................................................................... 35.3
[35.106] Variable displacement pump ....................................................... 35.4
[35.204] Remote control valves ............................................................. 35.5
[35.220] Auxiliary hydraulic pump and lines ................................................. 35.6
[35.300] Reservoir, cooler, and filters........................................................ 35.7
[35.304] Combination pump units ........................................................... 35.8
[35.600] High flow hydraulics................................................................ 35.9
Hitches, drawbars, and implement couplings.................................. 37
[37.100] Drawbars and towing hitches ...................................................... 37.1
Frames and ballasting ................................................................. 39
[39.100] Frame .............................................................................. 39.1
[39.110] Drawbar and hitch assembly ....................................................... 39.2
Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.200] Hydraulic control components...................................................... 41.2
[41.206] Pump ............................................................................... 41.3
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
[44.520] Rear wheels........................................................................ 44.2
Tracks and track suspension........................................................ 48
47680525 06/03/2014
5. [48.100] Tracks .............................................................................. 48.1
[48.130] Track frame and driving wheels .................................................... 48.2
[48.134] Track tension units ................................................................. 48.3
[48.138] Track rollers ........................................................................ 48.4
Cab climate control ..................................................................... 50
[50.104] Ventilation .......................................................................... 50.1
[50.200] Air conditioning..................................................................... 50.2
[50.300] Cab pressurizing system ........................................................... 50.3
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.301] Alternator........................................................................... 55.3
[55.302] Battery.............................................................................. 55.4
[55.010] Fuel injection system............................................................... 55.5
[55.014] Engine intake and exhaust system................................................. 55.6
[55.024] Transmission control system....................................................... 55.7
[55.045] Front axle control system .......................................................... 55.8
[55.046] Rear axle control system........................................................... 55.9
[55.048] Rear Power Take-Off (PTO) control system ..................................... 55.10
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system............... 55.11
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.12
[55.404] External lighting .................................................................. 55.13
[55.522] Cab Power Take-Off (PTO) controls ............................................. 55.14
[55.640] Electronic modules ............................................................... 55.15
[55.035] Remote control valve electric control ............................................ 55.16
[55.130] Rear three-point hitch electronic control system ................................. 55.17
[55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.18
[55.DTC] FAULT CODES.................................................................. 55.19
47680525 06/03/2014
8. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The information in this manual is up-to-date at the date of the publication. It is the policy of the manufacturer for
continuous improvement. Some information could not be updated due to modifications of a technical or commercial
type, or changes to the laws and regulations of different countries.
In case of questions, refer to your CASE IH Sales and Service Networks.
47680525 06/03/2014
3
9. INTRODUCTION
Safety rules
Quadtrac 470 NA model [ZEF300001 - ] NA
Quadtrac 540 NA model [ZEF300001 - ] NA
Quadtrac 540 NA scraper model [ZEF300001 - ] NA
Quadtrac 580 NA model [ZEF300001 - ] NA
Quadtrac 580 NA scraper model [ZEF300001 - ] NA
Quadtrac 620 NA model [ZEF300001 - ] NA
Rowtrac 370 NA model [ZEF300001 - ] NA
Rowtrac 420 NA model [ZEF300001 - ] NA
Rowtrac 470 NA model [ZEF300001 - ] NA
Rowtrac 500 NA model [ZEF300001 - ] NA
Steiger 370 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 370 NA standard wheeled [ZEF300001 - ] NA
Steiger 420 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 470 NA Wheeled scraper [ZEF300001 - ] NA
Steiger 470 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 500 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 500 NA wheeled scraper [ZEF300001 - ] NA
Steiger 500 QT NA model [ZEF300001 - ] NA
Steiger 500 QT NA scraper model [ZEF300001 - ] NA
Steiger 500 QT NA
Steiger 500 NA
Steiger 540 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 540 NA wheeled scraper [ZEF300001 - ] NA
Steiger 580 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 580 NA wheeled scraper [ZEF300001 - ] NA
Steiger 620 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 620 NA wheeled scraper [ZEF300001 - ] NA
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
47680525 06/03/2014
4
10. INTRODUCTION
Safety rules - Personal safety
General safety rules
Use caution when operating the machine on slopes. Raised equipment, full tanks and other loads will change the
center of gravity of the machine. The machine can tip or roll over when near ditches and embankments or uneven
surfaces.
Never permit anyone other than the operator to ride on the machine.
Never operate the machine under the influence of alcohol, drugs, or while otherwise impaired.
While driving on the road, the seat swivel position must always be straight forward and locked in position with no
rotation. The seat swivel should only be rotated for in field operation.
Stay off slopes too steep for safe operation. Shift down before you start up or down a hill with a heavy load. Avoid
“free wheeling.”
Do not drive on roads, or at high speed anywhere, with the differential lock engaged. Difficult steering will occur, and
can result in an accident. In field operation, use the differential lock for traction improvement, but release for turning
at row ends.
Do not exceed implement transport speed or the speed rating on the implement tires. Review the implements Oper-
ator’s Manual for specifications. Failure to comply could result in death or serious injury.
For speeds up to 16 km/h (10 mph), make sure that the weight of a trailed vehicle that is not equipped with brakes
does NOT EXCEED 1.5 times the Tractor weight. For speeds up to 40 km/h (25 mph), make sure that the weight of
the trailed vehicle that is not equipped with brakes, does NOT EXCEED the weight of the Tractor. Stopping distance
increases with increasing speed as the weight of the towed load increases, especially on hills and slopes.
Rear upset can result if pulling from wrong location on tractor. Hitch only to the drawbar. Use three point hitch only
with the implements designed for its use – not as a drawbar.
Do not look directly into the front or rear HID (high intensity discharge) lamps. Eye damage can occur.
Do not tamper with the ballast on the front or rear high intensity discharge (HID) lamp since it uses high voltage.
Personal injury or death can occur.
To avoid possible eye damage from microwave signals emitted by the radar sensor, do not look directly into the sensor
face.
When digging or using ground engaging attachments be aware of buried cables. Contact local utilities to determine
the locations of services.
Pay attention to overhead power lines and hanging obstacles. High voltage lines may require significant clearance
for safety.
Hydraulic oil or diesel fuel leaking under pressure can penetrate the skin, causing serious injury or infection.
• DO NOT use your hand to check for leaks. Use a piece of cardboard or paper.
• Stop engine, remove key and relieve the pressure before connecting or disconnecting fluid lines.
• Make sure all components are in good condition and tighten all connections before starting the engine or pressur-
izing the system.
• If hydraulic fluid or diesel fuel penetrates the skin, seek medical attention immediately.
• Continuous long term contact with hydraulic fluid may cause skin cancer. Avoid long term contact and wash the
skin promptly with soap and water.
Keep clear of moving parts. Loose clothing, jewelry, watches, long hair, and other loose or hanging items can become
entangled in moving parts.
Wear protective equipment when appropriate.
47680525 06/03/2014
6
11. INTRODUCTION
DO NOT attempt to remove material from any part of the machine while it is being operated or components are in
motion.
Make sure all guards and shields are in good condition and properly installed before operating the machine. Never
operate the machine with shields removed. Always close access doors or panels before operating the machine.
Dirty or slippery steps, ladders, walkways, and platforms can cause falls. Make sure these surfaces remain clean and
clear of debris.
A person or pet within the operating area of a machine can be struck or crushed by the machine or its equipment. DO
NOT allow anyone to enter the work area.
Raised equipment and/or loads can fall unexpectedly and crush persons underneath. Never allow anyone to enter
the area underneath raised equipment during operation.
Never operate engine in enclosed spaces as harmful exhaust gases may build up.
Before starting the machine, be sure that all controls are in neutral or park lock position.
Start the engine only from the operator’s seat. If the safety start switch is bypassed, the engine can start with the
transmission in gear. Do not connect or short across terminals on the starter solenoid. Attach jumper cables as
described in the manual. Starting in gear may cause death or serious injury.
Always keep windows, mirrors, all lighting, and Slow Moving Vehicle (SMV) emblem clean to provide the best possible
visibility while operating the machine.
Operate controls only when seated in the operator’s seat, except for those controls expressly intended for use from
other locations.
Before leaving the machine:
1. Park machine on a firm level surface.
2. Put all controls in neutral or park lock position.
3. Engage park brake. Use wheel chocks if required.
4. Lower all hydraulic equipment — Implements, header, etc.
5. Turn off engine and remove key.
When, due to exceptional circumstances, you would decide to keep the engine running after leaving the operator’s
station, then the following precautions must be followed:
1. Bring the engine to low idle speed.
2. Disengage all drive systems.
3. WARNING
Some components may continue to run down after disengaging drive systems.
Make sure all drive systems are fully disengaged.
Failure to comply could result in death or serious injury.
W0113A
Shift the transmission into neutral.
4. Apply the parking brake.
47680525 06/03/2014
7
12. SERVICE MANUAL
Engine
Quadtrac 470 NA model [ZEF300001 - ] , Quadtrac 540 NA model [ZEF300001
- ] , Quadtrac 540 NA scraper model [ZEF300001 - ] , Quadtrac 580 NA model
[ZEF300001 - ] , Quadtrac 580 NA scraper model [ZEF300001 - ] , Quadtrac
620 NA model [ZEF300001 - ] , Rowtrac 370 NA model [ZEF300001 - ] ,
Rowtrac 420 NA model [ZEF300001 - ] , Rowtrac 470 NA model [ZEF300001
- ] , Rowtrac 500 NA model [ZEF300001 - ] , Steiger 370 NA heavy duty
wheeled [ZEF300001 - ] , Steiger 370 NA standard wheeled [ZEF300001 - ] ,
Steiger 420 NA heavy duty wheeled [ZEF300001 - ] , Steiger 470 NA Wheeled
scraper [ZEF300001 - ] , Steiger 470 NA heavy duty wheeled [ZEF300001 - ] ,
Steiger 500 NA heavy duty wheeled [ZEF300001 - ] , Steiger 500 NA wheeled
scraper [ZEF300001 - ] , Steiger 500 QT NA model [ZEF300001 - ] , Steiger 500
QT NA scraper model [ZEF300001 - ] , Steiger 540 NA heavy duty wheeled
[ZEF300001 - ] , Steiger 540 NA wheeled scraper [ZEF300001 - ] , Steiger 580
NA heavy duty wheeled [ZEF300001 - ] , Steiger 580 NA wheeled scraper
[ZEF300001 - ] , Steiger 620 NA heavy duty wheeled [ZEF300001 - ] , Steiger
620 NA wheeled scraper [ZEF300001 - ]
47680525 06/03/2014
10
13. Engine - Engine and crankcase
Engine - Change fluid - Changing engine oil and filter
NOTE: Reduce to 300 hours or less if CASE IH AKCELA UNITEK NO. 1™ SBL CJ-4 is not used.
Change the engine oil and filter every 600 hours or once a
year or before storage, whichever occurs first. Your dealer
has approved oil and filters. Do not use other types of oil
or filters.
NOTE: For best results change the oil and filter while the
engine is still warm to the touch from operation (not hot).
The tractor must be on a level surface.
Remove the engine side shields.
9L engine
1. Remove the oil pan drain plug and drain the oil from the
engine into a container.
2. After all oil has drained, install new washer 98474302
on drain plug, center washer on plug and install drain
plug. Torque drain plug to 30 N·m (22 lb ft).
3. Clean the area around the filter head and housing on
the left side of the engine. Place a container under the
oil filter and turn the filter housing counterclockwise to
loosen with a 51 mm (2 in) wrench. After all oil has
drained from the filter, remove the housing with filter.
RAIL13TR04406AA 1
4. Install the new filter cartridge and O-ring. Lightly oil new
O-ring.
4. Reinstall the filter assembly onto the tractor. Do not
over tighten or O-ring will leak.
RCPH10FWD928BAM 2
47680525 06/03/2014
10.1 [10.001] / 3
14. Engine - Engine and crankcase
5. Fill with new oil into the engine oil fill (1).
NOTE: Total oil refill capacity will be determined by how
completely the crankcase drains. Do not fill above the high
mark on the dipstick (2) when refilling.
6. Operate the engine for five minutes at 1000 RPM.
Check for oil leaks at the filter base and drain plug.
7. Stop the engine. Wait approximately five minutes for
the oil to return to the oil pan. Check the oil level on the
dipstick (2) and add oil if needed.
RAIL13TR04406AA 3
13L engines
1. Remove the oil pan drain plug and drain the oil from the
engine into a container.
2. After all oil has drained, install new washer 98474302
on drain plug, center washer on plug and install drain
plug. Torque drain plug to 30 N·m (22 lb ft).
3. Place a container under the oil filter on the left side of
the engine. Use a 19 mm (0.75 in) socket to open drain
on bottom of housing. This will allow oil to drain from
the housing. After oil is drained, turn the filter housing
counterclockwise to loosen with a 51 mm (2 in) wrench
and remove the filter housing.
RAIL14TR00085AA 4
4. Install the new filter cartridge and O-ring.
4. Reinstall the filter assembly. Do not over tighten or the
O-ring will leak.
RCPH10FWD928BAM 5
47680525 06/03/2014
10.1 [10.001] / 4
15. Engine - Engine and crankcase
5. Fill with new oil into the engine oil fill (1).
NOTE: Total oil refill capacity will be determined by how
completely the crankcase drains. Do not fill above the high
mark on the dipstick (2) when refilling.
6. Operate the engine for five minutes at 1000 RPM.
Check for oil leaks at the filter base and drain plug.
7. Stop the engine. Wait approximately five minutes for
the oil to return to the oil pan. Check the oil level on the
dipstick (2) and add oil if needed.
RAIL13TR01857AA 6
47680525 06/03/2014
10.1 [10.001] / 5
16. Engine - Engine and crankcase
Engine - Remove - 9L
Rowtrac 370 NA model [ZEF300001 - ] NA
Steiger 370 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 370 NA standard wheeled [ZEF300001 - ] NA
Prior operation:
Hood support - Remove – Row crop frame, 9L engine (90.102)
1. Disconnect the driveshaft from the engine.
RAIL13TR02967AA 1
2. Label and disconnect the heater hoses from the tubes.
NOTE: Plug and cap all disconnected hoses and tubes.
RAIL13TR02966AA 2
3. Label and disconnect the two hoses for the diesel emis-
sions fluid tank solenoid.
RAIL13TR02969AA 3
47680525 06/03/2014
10.1 [10.001] / 6
17. Engine - Engine and crankcase
4. Loosen the hose clamp (1) at the turbo.
5. Remove the air intake tube (2) from the engine.
RAIL13TR03051AA 4
6. Disconnect the power cable (1) from the starter.
7. Disconnect the wire (2) from the starter.
8. Remove the bolt (3) and disconnect the ground strap
from the engine block.
RAIL13TR02970AA 5
9. Remove the left hand charged air cooler tube.
NOTE: Plug and cap disconnected tubes and ports.
RAIL13TR02978AA 6
47680525 06/03/2014
10.1 [10.001] / 7
18. Engine - Engine and crankcase
10. Disconnect the lower radiator hose at the engine.
RAIL13TR02971AA 7
11. Attach a support strap to the cooling package frame
and the chassis frame as shown to support the cooling
package.
RAIL13TR02973AA 8
12. Remove the right hand charged air cooler tube.
RAIL13TR02972AA 9
47680525 06/03/2014
10.1 [10.001] / 8
19. Engine - Engine and crankcase
13. Remove the clamp (1) securing the upper radiator
tube to the bracket on the engine.
14. Remove the upper radiator tube (2).
RAIL13TR02974AA 10
15. Cut the ties securing the harness and disconnect the
harness.
RAIL13TR02976AA 11
16. Loosen the viscous drive from the shaft.
NOTE: The fan pulley hub is left handed threaded.
RAIL13TR02979AA 12
47680525 06/03/2014
10.1 [10.001] / 9
20. Engine - Engine and crankcase
17. With the help of an assistant remove the fan out the
right hand side of the machine.
RAIL13TR02977AA 13
18. Disconnect the harness lead to the air conditioner high
pressure switch (1) and the clutch activation lead (2) .
RAIL13TR02981AA 14
19. Use a breaker bar to relieve the tension on the serpen-
tine belt and remove the belt from the air conditioner
compressor pulley.
RAIL13TR02987AA 15
47680525 06/03/2014
10.1 [10.001] / 10
21. Engine - Engine and crankcase
20. Support the compressor and remove the four mount-
ing bolts.
RAIL13TR02986AA 16
21. Set the compressor on the right hand front tire and
secure with holding straps as shown.
RAIL13TR02982AA 17
22. Disconnect the power cable (1) from the alternator.
23. Disconnect the exciter wire (2) from the alternator.
RAIL13TR02983AA 18
47680525 06/03/2014
10.1 [10.001] / 11
22. Engine - Engine and crankcase
24. Disconnect the harness (1).
25. Remove the bolt (2) securing the harness to the en-
gine block.
RAIL13TR02985AA 19
26. Unplug the connector (1).
27. Disconnect the main harness (2) from the engine con-
troller.
28. Disconnect the cable (3) from the junction box.
29. Cut the tie (4) securing the harness and cable to-
gether.
30. Move the harness (5) out from behind the junction box
and the engine to stay with the chassis during the
engine removal.
RAIL13TR02988AA 20
31. Remove the nut and bolt (1) securing the cable to the
bracket.
32. Remove the bolts (2) securing the bracket to the en-
gine block.
RAIL13TR02984AA 21
47680525 06/03/2014
10.1 [10.001] / 12
23. Engine - Engine and crankcase
33. Remove the bolt (1) securing the harness to the en-
gine block.
34. Disconnect the fuel inlet hose (2).
NOTE: Plug and cap all disconnected fuel hoses and fit-
tings.
RAIL13TR02993AA 22
35. Disconnect the fuel return hose.
RAIL13TR02991AA 23
36. Remove the right and left hand hold down brackets.
NOTE: Left hand side is shown. Remove both sides.
RAIL13TR02989AA 24
47680525 06/03/2014
10.1 [10.001] / 13
24. Engine - Engine and crankcase
37. Remove the front hold down bracket.
RAIL13TR02994AA 25
38. Attach the 4130 load rotor lifting bale or equivalent to
overhead crane and engine lift brackets.
NOTE: The engine lifting brackets are for vertical lifting
only. Any lifting device that is not vertically in line with the
lifting brackets can damage the engine rocker arm cover or
cause bracket failure.
RAIL13TR02992AA 26
39. Remove the engine.
RAIL13TR02990AA 27
47680525 06/03/2014
10.1 [10.001] / 14
25. Engine - Engine and crankcase
Engine - Install - 9L
Rowtrac 370 NA model [ZEF300001 - ] NA
Steiger 370 NA heavy duty wheeled [ZEF300001 - ] NA
Steiger 370 NA standard wheeled [ZEF300001 - ] NA
1. Set the engine in place on the chassis.
NOTE: The engine lifting brackets are for vertical lifting
only. Any lifting device that is not vertically in line with the
lifting brackets can damage the engine rocker arm cover or
cause bracket failure.
RAIL13TR02990AA 1
2. Remove the 4130 load rotor lifting bale or equivalent
from the engine lift brackets.
RAIL13TR02992AA 2
3. Install the front hold down bracket.
4. Torque the lower engine mount to frame bolts (1) to 90
- 107 N·m (66 - 79 lb ft).
5. Torque the ISO mount nut and bolt to 160 - 220 N·m
(118 - 162 lb ft).
RAIL13TR02994AA 3
47680525 06/03/2014
10.1 [10.001] / 15
26. Engine - Engine and crankcase
6. Install the right and left hand hold down brackets.
NOTE: Left hand side is shown. Install both sides.
7. Torque the bolts to 125 - 150 N·m (92 - 111 lb ft).
RAIL13TR02989AA 4
8. Connect the fuel return hose.
NOTE: Remove the plugs and caps from the disconnected
fuel hoses and fittings.
RAIL13TR02991AA 5
9. Route the harness and secure to the engine block with
the original bolt (1).
10. Connect the fuel inlet hose (2).
RAIL13TR02993AA 6
47680525 06/03/2014
10.1 [10.001] / 16
27. Engine - Engine and crankcase
11. Secure the bracket to the engine block (1) with the
original bolts.
12. Secure the cable to the bracket with the original nut
and bolt (2).
RAIL13TR02984AA 7
13. Route the harness (1) behind the junction box into it’s
original position.
14. Connect the cable (2) to the junction box as shown.
15. Connect the main harness (3) to the engine controller.
16. Plug in the connector (4) as shown.
17. Secure the harness and cable (5) together with a tie.
RAIL13TR02988AA 8
18. Connect the harness (1).
19. Route the harness to the top of the engine and secure
with the original bolt (2).
RAIL13TR02985AA 9
47680525 06/03/2014
10.1 [10.001] / 17
28. Engine - Engine and crankcase
20. Connect the exciter wire (1) to the alternator.
21. Connect the power cable (2) to the alternator.
RAIL13TR02983AA 10
22. Remove the compressor from the right hand front tire
and set in place on the engine.
RAIL13TR02982AA 11
23. Support the compressor, install the four mounting
bolts and tighten.
RAIL13TR02986AA 12
47680525 06/03/2014
10.1 [10.001] / 18
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
30. Engine - Engine and crankcase
24. Use a breaker bar to move the belt tensioner and in-
stall serpentine belt on to the air conditioner compres-
sor pulley.
RAIL13TR02987AA 13
25. Connect the harness lead to the air conditioner high
pressure switch (1) and the clutch activation lead (2) .
RAIL13TR02981AA 14
26. With the help from an assistant install the fan in place
from the right hand side of the machine.
RAIL13TR02977AA 15
47680525 06/03/2014
10.1 [10.001] / 19
31. Engine - Engine and crankcase
27. Thread the viscous drive on to the shaft.
NOTE: The fan pulley hub is left handed threaded.
28. Tighten the viscous drive on to the shaft.
RAIL13TR02979AA 16
29. Connect the harness and secure to the bracket with
ties.
RAIL13TR02976AA 17
30. Set the upper radiator tube (1) in place.
NOTE: Remove the plugs and caps from the disconnected
tubes and ports.
31. Install the clamp (2) securing the upper radiator tube
to the bracket on the engine.
32. Tighten the clamps (3) at the radiator and the thermo-
stat housing on the engine.
RAIL13TR02974AA 18
47680525 06/03/2014
10.1 [10.001] / 20
32. Engine - Engine and crankcase
33. Assemble the right hand charged air cooler tube.
RAIL13TR02972AA 19
34. Remove the support strap.
RAIL13TR02973AA 20
35. Connect the lower radiator hose at the engine and
tighten the clamp.
RAIL13TR02971AA 21
47680525 06/03/2014
10.1 [10.001] / 21
33. Engine - Engine and crankcase
36. Assemble the left hand charged air cooler tube.
RAIL13TR02978AA 22
37. Connect the ground strap (1) to the engine block.
38. Connect the wire (2) to the starter.
39. Connect the power cable (3) to the starter.
RAIL13TR02970AA 23
40. Assemble the air intake tube to the engine.
RAIL13TR03051AA 24
47680525 06/03/2014
10.1 [10.001] / 22
34. Engine - Engine and crankcase
41. Connect the two hoses for the diesel emissions fluid
tank solenoid as labeled during disassembly.
RAIL13TR02969AA 25
42. Connect the heater hoses to the tubes as labeled dur-
ing disassembly.
RAIL13TR02966AA 26
43. Connect the driveshaft to the engine.
44. Torque the bolts to 95 - 108 N·m (70 - 80 lb ft)
RAIL13TR02967AA 27
Next operation:
Hood support - Install – Row crop frame, 9L engine (90.102)
47680525 06/03/2014
10.1 [10.001] / 23