The document provides step-by-step instructions to remove the engine from the tractor. It begins by removing parts like the front weight carrier, hood, silencer, and electrical connections. Next, it involves disconnecting cables, lines and removing components like the steering wheel, instrument panel, and rear hood. Finally, it describes supporting the engine, removing mounting bolts, and separating the engine from the center housing. The overall process removes external components and disengages connections to separate the engine from the tractor chassis.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
7. INTRODUCTION
Foreword
Important notice
All maintenance and repair operations described in this manual should be carried out exclusively by CASE IH
authorised workshops. All instructions should be carefully observed and special equipment where indicated
should be used.
Anyone who carries out service operations described without carefully observing these prescriptions will be
directly responsible for any damage caused.
Notes for equipment
Equipment which CASE IH proposes and shows in this manual is:
- Studied and designed expressly for use on CASE IH tractors.
- Necessary to make reliable repair.
- Accurately built and strictly tested to offer efficient and long-lasting working life.
Notice
The words “front”, “rear”, “right-hand side” and “left-hand side” refer to the different parts as seen from the
operator’s seat oriented to the normal direction of movement of the tractor.
47899739 08/09/2015
3
8. INTRODUCTION
Safety rules
This warning symbol points out important messages involving personal safety. Carefully read the safety
rules contained herein and follow advised precautions to avoid potential hazards and safeguarded your safety.
In this manual you will find this symbol together with the following keywords.
WARNING: It gives warning about improper repair operations and potential consequences affecting the service tech-
nician’s personal safety.
DANGER: It gives specific warning about potential dangers for personal safety of the operator or other persons directly
or indirectly involved in the operation.
To prevent accidents
Most accidents and personal injuries taking place in workshops are due from non-observance of some essential rules
and safety precautions.
The possibility that an accident might occur with any type of machines should not be disregarded, no matter how well
the machine in question was designed and built.
A wise and careful service technician is the best precautions against accidents.
Careful observance of this only basic precaution would be enough to avoid many severe accidents.
DANGER
Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
47899739 08/09/2015
4
9. INTRODUCTION
Safety rules
Generalities
Carefully follow specified repair and maintenance procedures.
• Do not wear rings, wrist watches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves, open
jackets or shirts with open zips which could get caught in moving parts. Use approved safety clothing such as
anti-slipping footwear, gloves, safety goggles, helmets, etc.
• Wear safety glasses with side guards when cleaning parts using compressed air.
• Damaged or frayed wires and chains are unreliable. Do not use them for lifting or towing.
• Wear suitable protection such as approved eye protection, helmets, special clothing, gloves and footwear whenever
welding. All persons standing in vicinity of the welding process should wear approved eye protection. Never look
at the welding arc if your eyes are not suitably protected.
• Never carry out any repair on the machine if someone is sitting on the operator’s seat, except they are qualified
operators assisting in the operation to be carried out.
• Never operate the machine or use attachments from a place other than sitting at the operator’s seat or at the side
of the machine when operating the fender switches.
• Never carry out any operation on the machine when the engine is running, except when specifically indicated. Stop
the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves, etc.
• All repair and maintenance operations should be carried out with greatest care and attention.
• Disconnect the batteries and label all controls to warn that the tractor is being serviced. Block the machine and all
equipment which should be raised.
• Never check or fill fuel tanks or batteries, nor use starting liquid if you are smoking or near open flames as such
fluids are flammable.
• The fuel filling gun should always remain in contact with filler neck. Maintain this contact until the fuel stops flowing
into the tank to avoid possible sparks due to static electricity build-up.
• To transfer a failed tractor, use a trailer of a low loading platform trolley if available.
• To load and unload the machine from the transportation means, select a flat area providing a firm support to the
trailer or truck wheels. Firmly tie the machine to the truck or the trailer platform and block wheels as required by
the transporter.
• Always use lifting equipment of appropriate capacity to lift or move heavy components.
• Chains should always be safely fastened. Ensure that fastening device is strong enough to hold the load foreseen.
No persons should stand near the fastening point.
• The working area should be always kept clean and dry. Immediately clean any spillage of water or oil.
• Never use gasoline, diesel oil or other flammable liquids as cleaning agents. Use non-flammable non-toxic propri-
etary solvents.
• Do not pile up grease or oil soaked rags, as they constitute a great fire hazard. Always place them into a metal
container.
Start up
• Never run the engine in confined spaces which are not equipped with adequate ventilation for exhaust gas extrac-
tion.
• Never bring your body, arms, legs, feet, hands, fingers near fans or rotating belts.
Engine
• Always loosen the radiator cap very slowly before removing it to allow pressure in the system to dissipate. Coolant
should be topped up only when the engine is stopped.
• Do not fill up fuel tank when the engine is running.
• Never adjust the fuel injection pump when the tractor is moving. Never lubricate the tractor when the engine is
running.
47899739 08/09/2015
5
10. INTRODUCTION
Electrical systems
• If it is necessary to use auxiliary batteries, cables must be connected at both sides as follows.
(+) to (+) and (-) to (-). Avoid short-circuiting the terminals. Gas released from batteries is highly flammable. During
charging, leave the battery compartment uncovered to improve ventilation. Avoid sparks or flames near the battery
area. Do not smoke.
• Do not charge batteries in confined spaces.
• Always disconnect the batteries before performing any type of service on the electrical system.
Hydraulic systems
• Some fluid coming out from a very small port can be almost invisible and be strong enough to penetrate skin. For
this reason, Never use your hands to check for leaks, but use a piece of cardboard or a piece of wood for this
purpose. If any fluid is injected into the skin, seek medical aid immediately. Lack of immediate medical attention
may result in serious infections or dermatitis.
• Always take system pressure readings using the appropriate gauges.
Wheels and tires
• Check that the tires are correctly inflated at the pressure specified by the manufacturer. Periodically check for
possible damage to the rims and tires.
• Stay a the tire side when inflating.
• Check the pressure only when the tractor is unloaded and tires are cold to avoid wrong reading due to over- pres-
sure.
• Never cut, nor weld a rim with the inflated tire assembled.
• To remove the wheels, block both front and rear tractor wheels. Raise the tractor and install safe and stable supports
under the tractor in accordance with the regulations in force.
• Deflate the tire before removing any object caught into the tire tread.
• Never inflate tires using flammable gases as they may originate explosions and cause injuries to bystanders.
Removal and installation
• Lift and handle all heavy components using lifting equipment of adequate capacity. Ensure that parts are supported
by appropriate slings and hooks. Use lifting eyes provided to this purpose. Take care of the persons near the loads
to be lifted.
47899739 08/09/2015
6
12. Engine - Engine and crankcase
Engine - Remove
WARNING
Avoid injury!
Handle all parts carefully. Do not place your hands or fingers between parts. Use Personal Protec-
tive Equipment (PPE) as indicated in this manual, including protective goggles, gloves, and safety
footwear.
Failure to comply could result in death or serious injury.
W0208A
Separating engine from centre housing
1. Remove the front weight carrier (1).
GNIL14TR04757AB 1
2. Slide the lock (1) to right, hold and lift the handle (2) to
raise hood.
GNIL14TR04758AB 2
3. To maintain the hood in raised position a gas strut (1)
is provided underside hood.
GNIL14TR04759AA 3
47899739 08/09/2015
10.1 [10.001] / 19
13. Engine - Engine and crankcase
4. Disconnect battery terminals.
NOTE: Always disconnect the negative cable (1) first.
GNIL14TR04760AA 4
5. Loosen the silencer mounting clamp bolts (1) and re-
move the silencer assembly.
GNIL14TR04761AB 5
6. Remove the electrical couplers (1) for rear lamps,
flasher unit, fuse box etc.
7. Remove fuse box.
GNIL14TR04762AB 6
8. Unscrew hood mounting bracket bolts from engine
frame.
9. Unscrew gas strut bolts and remove the front hood.
GNIL14TR04763AB 7
47899739 08/09/2015
10.1 [10.001] / 20
14. Engine - Engine and crankcase
10. Disconnect electric connections (1) to starter motor.
GNIL14TR04764AB 8
11. Disconnect hand throttle cable fuel shut-off cable fuel
line and overflow lines and remove fuel tap bracket
bolts.
GNIL14TR04765AA 9
12. Remove the steering wheel cover.
GNIL14TR04766AB 10
13. Loosen the steering wheel securing nut and remove
the steering wheel using tool number 82834312 and
9971375.
GNIL14TR04766AA 11
47899739 08/09/2015
10.1 [10.001] / 21
15. Engine - Engine and crankcase
14. Disconnect the wiring connection (1).
GNIL14TR04768AB 12
15. Unscrew the rear bolts (1) and remove cover strip.
GNIL14TR04769AA 13
16. Remove the accelerator knob (1).
GNIL14TR04770AB 14
17. Unscrew all the screws (1) of instrument panel.
GNIL14TR04771AB 15
47899739 08/09/2015
10.1 [10.001] / 22
16. Engine - Engine and crankcase
18. Remove the steering boot (1).
GNIL14TR04772AB 16
19. Pull out the instrument panel from rear hood.
GNIL14TR04773AA 17
20. Disconnect all electric wire connections of the
switches and hourmeter cable from instrument clus-
ter. Also remove fuel tank cap.
GNIL14TR04774AB 18
21. Remove pull to stop knob and then centre panel. Un-
screw all rear hood securing bolts lift and remove rear
hood.
GNIL14TR04775AB 19
47899739 08/09/2015
10.1 [10.001] / 23
17. Engine - Engine and crankcase
22. Disconnect diesel overflow hose pipe (1) and fuel
sender electric connection (2).
GNIL14TR04776AB 20
23. Remove hand accelerator cable (3).
GNIL14TR04777AB 21
24. Loosen bolts (1) and release fuel tank strap.
NOTE: It is advisable to drain diesel from fuel tank if tank
is more than half filled.
GNIL14TR04778AB 22
25. Position splitting trolley special tool number 292320
with engine supports in position, also block front
wheels both at front and back using suitable wedges.
GNIL14TR04779AA 23
47899739 08/09/2015
10.1 [10.001] / 24
18. Engine - Engine and crankcase
26. Remove knuckle joint nut (1) and disconnect drag link
from control lever (2).
GNIL14TR04780AB 24
27. Support the engine at the back of the front axle and
position wedges between axle and support to prevent
articulation.
GNIL14TR04781AA 25
28. Remove the bolts securing the engine to the centre
housing. After removing platform bolts.
GNIL14TR04782AA 26
29. Wheel the centre housing and rear wheels away from
the engine.
GNIL14TR04783AA 27
47899739 08/09/2015
10.1 [10.001] / 25
19. Engine - Engine and crankcase
Separating front axle from engine
With engine previously separated from centre housing.
DANGER
Heavy objects!
Lift and handle all heavy components using lift-
ing equipment with adequate capacity. Always
support units or parts with suitable slings or
hooks. Make sure the work area is clear of all
bystanders.
Failure to comply will result in death or serious
injury.
D0076A
1. Disconnect headlight harness connection (1) and horn
wirings. GNIL14TR04784AB 28
2. Disconnect hose (1) from radiator and drain the
coolant.
GNIL14TR04785AB 29
3. Loosen the clamps (1) and radiator (2).
4. Remove the radiator bracket and deflector support
bracket securing bolt.
GNIL14TR04786AB 30
5. Support the front axle at the front bracket.
6. Support the engine using a suitable hoist.
GNIL14TR04787AA 31
47899739 08/09/2015
10.1 [10.001] / 26
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Engine - Engine and crankcase
7. Remove buckle up bolts between the engine and front
support carefully lift the engine from the front axle sup-
port (1) ensuring that all wires and tubes are discon-
nected. Place the engine onto a suitable stand for re-
pair.
GNIL14TR04788AB 32
47899739 08/09/2015
10.1 [10.001] / 27
22. Engine - Engine and crankcase
Engine - Service instruction
Diesel engine strip down
In the following procedures and illustrations the engine
in the main is shown removed from the tractor.
However there are certain operations that can per-
formed with the engine still in the tractor, or separated
at the connection to the front axle support, or separated
from the transmission housing.
The engine overhaul procedure initially describes the
assembly process for rebuilding an engine using all new
components. Following this section are defined head-
ings, which describe detailed repair specifications and
procedures, where components are suitable for re-use.
Where overhaul of components is required without en-
gine being removed from the tractor refer to the follow-
ing headings, and the relevant paragraphs, in the main
overhaul procedure.
Operations or repairs that can be performed with the
engine still in the tractor.
1. Cylinder head and associated inlet and exhaust
components.
2. Fuel injection pump and related parts.
3. Water pump, thermostat, and associated compo-
nents.
4. Radiator and associated parts.
Operations or repair that are performed with the engine
separated from the front axle.
1. Front oil seal
2. Timing cover and gears
3. Cam shaft
4. Oil pump (with oil sump removed)
5. Oil sump
Operations or repairs that are performed with the en-
gine separated from the transmission housing.
1. Rear oil seal / bracket.
2. Dismantle the engine by referring to the following
removal procedure. Refer to the specification sec-
tion as necessary.
NOTE: All gaskets, seals and O-rings must be replaced
while reassembling. Where new sealant is to be applied
refer to Engine - Sealing (10.001).
47899739 08/09/2015
10.1 [10.001] / 28
23. Engine - Engine and crankcase
Engine - Install
Installation of the engine is reversal of the removal pro-
cedure, noting the following points:
1. Apply thread sealant to bolt.
2. Ensure all attaching hardware is tightened to the
correct torque value as detailed in Engine - Torque
(10.001).
3. Ensure after installation that all fluid levels are correct
prior to start up. Start and run the engine until cor-
rect operating temperature is achieved to purge air from
cooling system. Stop engine, check for leaks, rectify as
required and recheck fluid levels.
47899739 08/09/2015
10.1 [10.001] / 29