This document is a service manual for the Case IH Axial-Flow 7250, 8250, and 9250 combines with Tier 4B engines. It provides an introduction and table of contents that lists over 55 sections covering all major systems of the combines, including the engine, transmission, axles, hydraulics, steering, electrical systems, and cab climate control. Each section number links to detailed information, specifications, and repair procedures for that system component.
New holland t8.350 powershift transmission (pst) tractor service repair manua...usjekkmdmd
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing engine cooling and emissions components before disconnecting hoses, tubes, sensors, and harnesses from the engine.
New holland t8.380 powershift transmission (pst) tractor service repair manua...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland t8.380 pst tier 4 b tractor service repair manual [zhre04001 ]ufjjjsksekemme
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing cooling and emissions systems components before disconnecting engine sensors, tubes, and hoses and removing the intake tube. Caps or plugs must be installed when disconnecting hydraulic lines.
New holland t8.320 powershift transmission (pst) tractor service repair manua...yhfhjjssennea
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland t8.410 smart trax™ powershift transmission (pst) tractor service ...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains detailed sections for servicing and repairing components of the tractors. The manual begins with an introduction and table of contents that lists the major vehicle systems and corresponding section numbers for finding repair information.
New holland 8670 tractor service repair manualfjskekertkskemm
This document is a repair manual section for a New Holland tractor engine and lubrication system. It includes specifications, torque values, grease and sealant types, special tools, descriptions of engine operation and components. The section covers the cylinder head, camshaft, crankshaft, connecting rods, pistons, manifolds, cylinder block, and timing gears. It also describes the engine lubrication system.
Massey ferguson mf3120 tractor service parts catalogue manual (part number 1...fjskekertkskemm
1. The document provides a list of parts and their descriptions for the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, and turbocharger of a Massey Ferguson T6.60 engine for tractors 3120/3120T.
2. It includes item numbers, part numbers, quantities, part names, and comments for each component.
3. The list contains over 50 individual parts for the various engine systems, with detailed information on replacements, serviceability, and component interactions.
Massey ferguson 4225 tractors ( k37008) service parts catalogue manual (part...fjskekertkskemm
1. The document provides parts lists and technical specifications for cylinder blocks, crankshafts, pistons, and connecting rods for Massey Ferguson 4225, 4235, and 4240 tractors.
2. It lists over 40 individual parts with part numbers, quantities, descriptions, and other identifying information. Footnotes provide additional details on some part specifications.
3. The parts lists are broken into sections covering different components and variants distinguished by color coding ("blue" or "green") and intended tractor model.
New holland t8.350 powershift transmission (pst) tractor service repair manua...usjekkmdmd
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing engine cooling and emissions components before disconnecting hoses, tubes, sensors, and harnesses from the engine.
New holland t8.380 powershift transmission (pst) tractor service repair manua...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland t8.380 pst tier 4 b tractor service repair manual [zhre04001 ]ufjjjsksekemme
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing cooling and emissions systems components before disconnecting engine sensors, tubes, and hoses and removing the intake tube. Caps or plugs must be installed when disconnecting hydraulic lines.
New holland t8.320 powershift transmission (pst) tractor service repair manua...yhfhjjssennea
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland t8.410 smart trax™ powershift transmission (pst) tractor service ...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains detailed sections for servicing and repairing components of the tractors. The manual begins with an introduction and table of contents that lists the major vehicle systems and corresponding section numbers for finding repair information.
New holland 8670 tractor service repair manualfjskekertkskemm
This document is a repair manual section for a New Holland tractor engine and lubrication system. It includes specifications, torque values, grease and sealant types, special tools, descriptions of engine operation and components. The section covers the cylinder head, camshaft, crankshaft, connecting rods, pistons, manifolds, cylinder block, and timing gears. It also describes the engine lubrication system.
Massey ferguson mf3120 tractor service parts catalogue manual (part number 1...fjskekertkskemm
1. The document provides a list of parts and their descriptions for the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, and turbocharger of a Massey Ferguson T6.60 engine for tractors 3120/3120T.
2. It includes item numbers, part numbers, quantities, part names, and comments for each component.
3. The list contains over 50 individual parts for the various engine systems, with detailed information on replacements, serviceability, and component interactions.
Massey ferguson 4225 tractors ( k37008) service parts catalogue manual (part...fjskekertkskemm
1. The document provides parts lists and technical specifications for cylinder blocks, crankshafts, pistons, and connecting rods for Massey Ferguson 4225, 4235, and 4240 tractors.
2. It lists over 40 individual parts with part numbers, quantities, descriptions, and other identifying information. Footnotes provide additional details on some part specifications.
3. The parts lists are broken into sections covering different components and variants distinguished by color coding ("blue" or "green") and intended tractor model.
Massey ferguson 342 tractor service parts catalogue manual (part number 819793)fjskekertkskemm
This document provides part numbers and descriptions for engine components of a Massey Ferguson 342 tractor with an Ad3.152 engine. It includes listings for the cylinder block, crankshaft, pistons, piston rods, cylinder head, and other engine parts, along with notes on part replacements and serial number ranges. Diagrams show the layout and components of the engine cylinder block and head.
Massey ferguson 251 xe tractor (brazil) service parts catalogue manual (part ...fjskekertkskemm
This document contains parts lists and diagrams for the engine and related components of a Massey Ferguson 251XE tractor made for the Brazilian market. It includes over 30 pages detailing over 250 individual parts that make up the engine, from major components like the cylinder block and head to minor items like bolts, pins, and seals. Exploded diagrams show the assembly of components like the crankshaft, pistons, connecting rods, timing gears, and camshaft.
Massey ferguson 240 tractor ( -- a20287 ( gb )) service parts catalogue manua...fjskekertkskemm
This document provides part numbers and descriptions for components of a Massey Ferguson 240 tractor engine. It includes listings for the cylinder block, crankshaft, pistons, connecting rods, and other internal engine parts. Item numbers, part numbers, quantities, descriptions, and additional identifying information like serial numbers or build lists are provided for each component.
Kubota v2403 m-di-t diesel engine service repair manualfjskekertkskemm
This document provides specifications for several Kubota diesel engine models. It includes information on displacement, power output, operating speed, lubrication system, cooling system, dimensions, weight and other technical details. The specifications cover single-cylinder, three-cylinder and four-cylinder engine configurations with power ratings ranging from 20kW to 44kW. Performance data, components and specifications may vary between standard and turbocharged versions of each model.
John deere z335 e z trak mower (s.n.010001-) service repair technical manual ...fjskekertkskemm
The document provides instructions for removing and installing an engine on a ZTrak mower. It involves disconnecting wiring, fuel lines, belts, and removing mounting bolts. The engine is then installed by reversing these steps and reconnecting all components. Tightening specifications are provided for mounting bolts and other fasteners. Safety cautions are included for fuel, belts, and hot surfaces.
John deere power tech 10.5l diesel base engine service repair technical manua...fjskekertkskemm
This document provides instructions to remove a cylinder head from a CTM100 diesel engine. The steps include:
1. Draining oil and coolant from the engine.
2. Removing the intake manifold, turbocharger, and exhaust manifold.
3. Removing the thermostat housing/water manifold.
4. Removing the rocker arm assembly and push rods.
5. Removing the cylinder head bolts and lifting off the cylinder head.
John deere 326 d skid steer loader (manual controls) service repair manual (t...fjskekertkskemm
This document provides instructions for disassembling and assembling a track adjuster cylinder. It describes how to safely remove the recoil spring and disassemble the cylinder components like seals and rods. Precautions are outlined to prevent damage to parts. The proper process for cleaning, inspecting, and reinstalling components in reverse order is described. Torque specifications and measurements are provided for correctly assembling and adjusting the cylinder.
John deere 107 s lawn tractor service repair technical manual (tm113319)fjskekertkskemm
This technical manual provides instructions for servicing X105, X125, X145, X165, and 107S Tractors. It begins with several pages emphasizing safety, including warnings about handling batteries, preventing acid burns, avoiding fires, and following other precautions. The document explains that the manual is divided into repair and operation/testing sections and provides fundamental service information.
John deere 92 h riding lawn tractor service repair technical manual (tm113419)fjskekertkskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, including reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms, and push rods before removing the head and gasket.
Caterpillar cat d8 t track type tractor dozer bulldozer (prefix mln) service ...fjskekertkskemm
1. The document provides instructions for removing and installing various components of the front gear group for a Caterpillar D8T track-type tractor powered by a C15 engine.
2. The removal procedure describes removing components like the front cover, front housing, air compressor, and water pump before removing the front gear group.
3. Special tools are listed and safety notices are provided, such as not turning the crankshaft or camshaft when the camshaft gear is removed to avoid interference and engine damage.
The document provides instructions for removing and installing the front suspension frame on a 740 Ejector Articulated Truck. It describes using tools like air/hydraulic jacks, lever pullers, and bolts to remove components like brackets, collars, and washers from the suspension frame. It then gives the reverse steps for installing these components, ensuring proper torque of bolts and use of grease. Safety precautions are provided to relieve pressure before working on cylinders and to use lifting equipment properly due to component weights of around 250 kg.
The document provides instructions for removing and installing a gear pump used in an aftercooler system on a 740 Articulated Truck. The removal process involves disconnecting hoses from the pump, removing bolts securing it, and removing an O-ring seal. The installation is the reverse of removal, including cleaning parts, lubricating seals, aligning the pump splines, and reconnecting hoses.
The document provides instructions for assembling and disassembling a piston pump used in articulated trucks. It involves 26 steps to assemble the pump, including installing retaining rings, seals, bearings, springs, pins and other components in the proper order and orientation. Disassembly of the secondary steering pump and electric motor is also described and involves removing hoses, cables, covers and bolts to detach the pump unit.
Caterpillar cat 320 n excavator (prefix 9wg) service repair manual (9wg00001 ...fjskekertkskemm
This document provides instructions for removing a unit injector from an excavator engine. It begins by requiring the removal of the rocker shaft and pushrods. Then it describes using a bar to compress the unit injector springs and slide the injector out of the cylinder head. Contaminants are warned against as they can cause rapid wear. The document is part of a service manual for excavator models 320, 320L, and 320N.
Caterpillar cat 320 l excavator (prefix 9wg) service repair manual (9wg00001 ...fjskekertkskemm
This document provides instructions for removing a unit injector from an excavator engine. It begins by requiring the removal of the rocker shaft and pushrods. Then it describes using a bar to compress the unit injector springs and slide the injector out of the cylinder head. Contaminants are warned against as they can cause rapid wear. The document is part of a service manual for excavator models 320, 320L, and 320N.
Caterpillar cat 320 e rr excavator (prefix mew) service repair manual (mew000...fjskekertkskemm
This document provides instructions for removing and installing the front gear group on a Caterpillar C6.6 engine. The removal procedure involves using tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. The installation procedure specifies cleaning and inspecting parts, aligning timing marks on gears, checking backlash and end play, and torquing bolts to the specified values. Proper positioning of the crankshaft is emphasized to avoid piston and valve interference.
Caterpillar cat 320 e lrr excavator (prefix mew) service repair manual (mew00...fjskekertkskemm
The document provides instructions for removing and installing the front gear group on a 320E LRR excavator. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins before removing components.
2. Marking gear alignments and removing the camshaft and idler gears.
3. Cleaning and inspecting components, installing gears in reverse order while aligning timing marks, and checking backlash and end play.
4. Locking components, tightening fasteners to specification, and positioning the valve mechanism after installation is complete.
This document provides instructions for installing a governor on an excavator engine. It outlines the required tools and parts. The instructions describe applying lubricant to O-rings, placing the governor in position, and installing clips and bolts to hold it in place. Finally, it mentions checking the fuel setting adjustment after installation and installing the fuel shutoff solenoid.
This document provides disassembly instructions for the piston pump of a 252B3 skid steer loader. It lists 69 steps to fully disassemble the pump, removing components like fittings, springs, seals, bearings, shafts and housings. Measurement and marking steps are included to aid reassembly. Tools required include rulers, retaining ring pliers, link brackets, bolts and washers, drivers, bearing pullers and presses. Safety warnings are given to release spring forces carefully.
This document provides instructions for removing and installing the flywheel, flywheel housing, crankshaft rear seal, and crankshaft pulley on a 3034 engine. The procedures describe using various tools to remove bolts, drilling holes, inserting slide hammers, cleaning surfaces, applying gasket maker, and torquing bolts. Precautions are provided to keep parts clean and prevent damage.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Massey ferguson 342 tractor service parts catalogue manual (part number 819793)fjskekertkskemm
This document provides part numbers and descriptions for engine components of a Massey Ferguson 342 tractor with an Ad3.152 engine. It includes listings for the cylinder block, crankshaft, pistons, piston rods, cylinder head, and other engine parts, along with notes on part replacements and serial number ranges. Diagrams show the layout and components of the engine cylinder block and head.
Massey ferguson 251 xe tractor (brazil) service parts catalogue manual (part ...fjskekertkskemm
This document contains parts lists and diagrams for the engine and related components of a Massey Ferguson 251XE tractor made for the Brazilian market. It includes over 30 pages detailing over 250 individual parts that make up the engine, from major components like the cylinder block and head to minor items like bolts, pins, and seals. Exploded diagrams show the assembly of components like the crankshaft, pistons, connecting rods, timing gears, and camshaft.
Massey ferguson 240 tractor ( -- a20287 ( gb )) service parts catalogue manua...fjskekertkskemm
This document provides part numbers and descriptions for components of a Massey Ferguson 240 tractor engine. It includes listings for the cylinder block, crankshaft, pistons, connecting rods, and other internal engine parts. Item numbers, part numbers, quantities, descriptions, and additional identifying information like serial numbers or build lists are provided for each component.
Kubota v2403 m-di-t diesel engine service repair manualfjskekertkskemm
This document provides specifications for several Kubota diesel engine models. It includes information on displacement, power output, operating speed, lubrication system, cooling system, dimensions, weight and other technical details. The specifications cover single-cylinder, three-cylinder and four-cylinder engine configurations with power ratings ranging from 20kW to 44kW. Performance data, components and specifications may vary between standard and turbocharged versions of each model.
John deere z335 e z trak mower (s.n.010001-) service repair technical manual ...fjskekertkskemm
The document provides instructions for removing and installing an engine on a ZTrak mower. It involves disconnecting wiring, fuel lines, belts, and removing mounting bolts. The engine is then installed by reversing these steps and reconnecting all components. Tightening specifications are provided for mounting bolts and other fasteners. Safety cautions are included for fuel, belts, and hot surfaces.
John deere power tech 10.5l diesel base engine service repair technical manua...fjskekertkskemm
This document provides instructions to remove a cylinder head from a CTM100 diesel engine. The steps include:
1. Draining oil and coolant from the engine.
2. Removing the intake manifold, turbocharger, and exhaust manifold.
3. Removing the thermostat housing/water manifold.
4. Removing the rocker arm assembly and push rods.
5. Removing the cylinder head bolts and lifting off the cylinder head.
John deere 326 d skid steer loader (manual controls) service repair manual (t...fjskekertkskemm
This document provides instructions for disassembling and assembling a track adjuster cylinder. It describes how to safely remove the recoil spring and disassemble the cylinder components like seals and rods. Precautions are outlined to prevent damage to parts. The proper process for cleaning, inspecting, and reinstalling components in reverse order is described. Torque specifications and measurements are provided for correctly assembling and adjusting the cylinder.
John deere 107 s lawn tractor service repair technical manual (tm113319)fjskekertkskemm
This technical manual provides instructions for servicing X105, X125, X145, X165, and 107S Tractors. It begins with several pages emphasizing safety, including warnings about handling batteries, preventing acid burns, avoiding fires, and following other precautions. The document explains that the manual is divided into repair and operation/testing sections and provides fundamental service information.
John deere 92 h riding lawn tractor service repair technical manual (tm113419)fjskekertkskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, including reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms, and push rods before removing the head and gasket.
Caterpillar cat d8 t track type tractor dozer bulldozer (prefix mln) service ...fjskekertkskemm
1. The document provides instructions for removing and installing various components of the front gear group for a Caterpillar D8T track-type tractor powered by a C15 engine.
2. The removal procedure describes removing components like the front cover, front housing, air compressor, and water pump before removing the front gear group.
3. Special tools are listed and safety notices are provided, such as not turning the crankshaft or camshaft when the camshaft gear is removed to avoid interference and engine damage.
The document provides instructions for removing and installing the front suspension frame on a 740 Ejector Articulated Truck. It describes using tools like air/hydraulic jacks, lever pullers, and bolts to remove components like brackets, collars, and washers from the suspension frame. It then gives the reverse steps for installing these components, ensuring proper torque of bolts and use of grease. Safety precautions are provided to relieve pressure before working on cylinders and to use lifting equipment properly due to component weights of around 250 kg.
The document provides instructions for removing and installing a gear pump used in an aftercooler system on a 740 Articulated Truck. The removal process involves disconnecting hoses from the pump, removing bolts securing it, and removing an O-ring seal. The installation is the reverse of removal, including cleaning parts, lubricating seals, aligning the pump splines, and reconnecting hoses.
The document provides instructions for assembling and disassembling a piston pump used in articulated trucks. It involves 26 steps to assemble the pump, including installing retaining rings, seals, bearings, springs, pins and other components in the proper order and orientation. Disassembly of the secondary steering pump and electric motor is also described and involves removing hoses, cables, covers and bolts to detach the pump unit.
Caterpillar cat 320 n excavator (prefix 9wg) service repair manual (9wg00001 ...fjskekertkskemm
This document provides instructions for removing a unit injector from an excavator engine. It begins by requiring the removal of the rocker shaft and pushrods. Then it describes using a bar to compress the unit injector springs and slide the injector out of the cylinder head. Contaminants are warned against as they can cause rapid wear. The document is part of a service manual for excavator models 320, 320L, and 320N.
Caterpillar cat 320 l excavator (prefix 9wg) service repair manual (9wg00001 ...fjskekertkskemm
This document provides instructions for removing a unit injector from an excavator engine. It begins by requiring the removal of the rocker shaft and pushrods. Then it describes using a bar to compress the unit injector springs and slide the injector out of the cylinder head. Contaminants are warned against as they can cause rapid wear. The document is part of a service manual for excavator models 320, 320L, and 320N.
Caterpillar cat 320 e rr excavator (prefix mew) service repair manual (mew000...fjskekertkskemm
This document provides instructions for removing and installing the front gear group on a Caterpillar C6.6 engine. The removal procedure involves using tools to lock the crankshaft, camshaft and fuel injection pump in position before removing gears. The installation procedure specifies cleaning and inspecting parts, aligning timing marks on gears, checking backlash and end play, and torquing bolts to the specified values. Proper positioning of the crankshaft is emphasized to avoid piston and valve interference.
Caterpillar cat 320 e lrr excavator (prefix mew) service repair manual (mew00...fjskekertkskemm
The document provides instructions for removing and installing the front gear group on a 320E LRR excavator. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins before removing components.
2. Marking gear alignments and removing the camshaft and idler gears.
3. Cleaning and inspecting components, installing gears in reverse order while aligning timing marks, and checking backlash and end play.
4. Locking components, tightening fasteners to specification, and positioning the valve mechanism after installation is complete.
This document provides instructions for installing a governor on an excavator engine. It outlines the required tools and parts. The instructions describe applying lubricant to O-rings, placing the governor in position, and installing clips and bolts to hold it in place. Finally, it mentions checking the fuel setting adjustment after installation and installing the fuel shutoff solenoid.
This document provides disassembly instructions for the piston pump of a 252B3 skid steer loader. It lists 69 steps to fully disassemble the pump, removing components like fittings, springs, seals, bearings, shafts and housings. Measurement and marking steps are included to aid reassembly. Tools required include rulers, retaining ring pliers, link brackets, bolts and washers, drivers, bearing pullers and presses. Safety warnings are given to release spring forces carefully.
This document provides instructions for removing and installing the flywheel, flywheel housing, crankshaft rear seal, and crankshaft pulley on a 3034 engine. The procedures describe using various tools to remove bolts, drilling holes, inserting slide hammers, cleaning surfaces, applying gasket maker, and torquing bolts. Precautions are provided to keep parts clean and prevent damage.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
10. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
51586252 07/03/2019
3
11. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
51586252 07/03/2019
4
12. INTRODUCTION
Personal safety
WARNING
Risk of harm during maintenance of the machine!
Before you start servicing the machine, attach a DO NOT OPERATE warning tag to the machine in a
visible area.
Failure to comply could result in death or serious injury.
W1242A
Attach a DO NOT OPERATE (TAG) to the machine in an area that is clearly visible whenever the machine is not
operating properly and/or requires service.
Complete the tag information for the "REASON" the tag is attached by describing the malfunction or service required.
Validate the reason for attaching the tag by signing your name in the designated area on the tag.
The tag should only be removed by the person who signed and attached the tag, after validating the repairs or services
have been completed.
51586252 07/03/2019
5
15. Engine - Engine and crankcase
Engine - Remove
AXIAL-FLOW® 7250
AXIAL-FLOW® 8250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
Prior operation:
Remove the oil drain hose. See Engine - Remove engine oil drain line and drain valve (10.001)
Prior operation:
Radiator - Drain fluid (10.400)
Prior operation:
Deaeration tank - Remove (10.400)
Prior operation:
Engine shield - Remove (90.102)
Prior operation:
Radiator hoses - Remove (10.400)
Prior operation:
Central wiring harness - Remove (55.100)
Prior operation:
Aftercooler air supply and return lines - Remove air supply tube (10.310)
Prior operation:
Aftercooler air supply and return lines - Remove air return tube (10.310)
Prior operation:
Air cleaner connection between filter and engine - Remove - Axial-Flow® 7250 and Axial-Flow® 8250 (10.202)
Prior operation:
Connection tube from filter to muffler - Remove (10.202)
Prior operation:
Fan - Remove (10.414)
Prior operation:
Air-conditioning compressor - Remove (from Cursor 11 Engine) (50.200)
Prior operation:
Fuel supply lines Low pressure - Remove from the engine (10.210)
Prior operation:
Fuel return lines - Remove from the engine (10.210)
Prior operation:
Exhaust muffler - Remove mixer tube (10.254)
Prior operation:
Exhaust muffler - Remove exhaust tube from turbo charger to Diesel Oxidation Catalyst (DOC) (10.254)
Prior operation:
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA lines - Remove DEF hose bundle from the engine compartment
(10.500)
Prior operation:
Selective Catalytic Reduction (SCR) muffler and catalyst - Remove (10.500)
Prior operation:
51586252 07/03/2019
10.1 [10.001] / 3
16. Engine - Engine and crankcase
Diesel Oxidation Catalyst (DOC) - Remove (10.500)
1. Disengage the battery connect switch (1).
NHIL13AF00586AA 1
2. Attach a suitable lift chain to the front lift eye (1) at the
front of the engine.
NHIL14AF00431AA 2
3. Attach a suitable lift chain to the back lift eye (1) at the
rear of the engine.
NHIL14AF00432AA 3
51586252 07/03/2019
10.1 [10.001] / 4
17. Engine - Engine and crankcase
4. Connect the lift chain to a suitable lifting device.
5. Raise the lifting device enough to support the engine
during removal of the engine mounting bolts.
NOTE: The lifting device should be rated for at least
907.2 kg (2000 lb). Allow enough clearance to lift the
engine from the combine, approximately 7.0 m (23 ft) from
the floor.
10013136 4
6. From the grain tank side of the engine, loosen the front,
engine mounting bolts (1). Do not remove the mounting
bolts at this time.
7. From the platform side, loosen the front, engine mount-
ing bolts (2). Do not remove the mounting bolts at this
time.
NHIL14AF01001AA 5
8. From the rear of the engine, loosen but do not remove
all the bolts and washers (1) that couple the engine to
the gearbox. There are twelve bolts and washers in
total.
9. For safety reasons to the radiators, place a sheet of
plywood, cut to size, in front of the cooler box for pro-
tection.
10. With the engine securely supported by the lifting de-
vice, remove all of the engine mounting bolts and the
engine to the gearbox coupling bolts that were loos-
ened in the previous steps.
11. Slide the engine towards the cooler box to disengage
the flex plate from the gearbox input shaft.
12. Carefully lift the engine from the frame and remove
from the combine. NHIL14AF01004AA 6
Next operation:
Engine - Install (10.001) .
51586252 07/03/2019
10.1 [10.001] / 5
18. Engine - Engine and crankcase
Engine - Install
AXIAL-FLOW® 7250
AXIAL-FLOW® 8250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
NOTE: Illustrations are for reference only. It may not be the actual engine.
1. Before installing the engine, apply LOCTITE® SILVER
GRADE ANTI-SEIZE to the input shaft (1) of the gearbox.
83070284 1
2. Attach a suitable chain to the front lift eye (1) at the front
of the engine.
86070259 2
51586252 07/03/2019
10.1 [10.001] / 6
19. Engine - Engine and crankcase
3. Attach a suitable chain to the back lift eye (1) at the rear
of the engine.
86070260 3
4. Connect the lift chain to a suitable lifting device.
5. Carefully lift the engine above the combine and lower
into position in the frame.
NOTE: The lifting device should be rated for at least
907.2 kg (2000 lb). Allow enough clearance to lift the en-
gine from the combine, approximately 907.2 kg (2000 lb)
from the floor.
10013136 4
6. For safety reasons to the radiator, place a sheet of ply-
wood, cut to size, in front of the radiator for protection.
7. Slide the engine towards the gearbox onto the gear box
input shaft.
8. Align the holes of the gearbox with the engine and hand
start a bolt with a washer (1) on each side of the cou-
pling, going back and forth until all bolts with a washers
are installed.
NHIL14AF01004AA 5
51586252 07/03/2019
10.1 [10.001] / 7
20. Engine - Engine and crankcase
9. With the engine positioned in the frame, align the front
mounting hole on the grain tank side and install the bolt
with washers (1) into the mount. Do not tighten yet.
10. Align the front mounting hole on the platform side. In-
stall the bolt with washers (1) into the mount.
11. Tighten and torque the front engine mounting bolts to
217 Nm (160.1 lb ft).
12. Tighten and torque the engine gearbox bolts to 41 –
51 Nm (30.2 – 37.6 lb ft).
NHIL14AF01001AA 6
13. Diesel Oxidation Catalyst (DOC) - Install (10.500)
14. Selective Catalytic Reduction (SCR) muffler and
catalyst - Remove (10.500)
15. Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA lines -
Install DEF hose bundle from the engine compart-
ment (10.500)
16. Exhaust muffler - Install exhaust tube from
turbo charger to Diesel Oxidation Catalyst (DOC)
(10.254)
17. Exhaust muffler - Install mixer tube (10.254)
18. Fuel return lines - Install to the engine (10.210)
19. Fuel supply lines Low pressure - Install to the en-
gine (10.210)
20. Air-conditioning compressor - Install (on Cursor
11 Engine) (50.200)
21. Fan - Install (10.414)
22. Connection tube from filter to muffler - Install
(10.202)
23. Air cleaner connection between filter and engine -
Install - Axial-Flow® 9250 (10.202)
24. Aftercooler air supply and return lines - Install air
return tube (10.310)
25. Aftercooler air supply and return lines - Install air
supply tube (10.310)
26. Central wiring harness - Install (55.100)
27. Radiator hoses - Install (10.400)
28. Engine shield - Install (90.102)
29. Deaeration tank - Install (10.400)
30. Radiator - Filling (10.400)
31. Engine - Install engine oil drain line and drain
valve (10.001)
51586252 07/03/2019
10.1 [10.001] / 8
21. Engine - Engine and crankcase
32. Engage the battery connect switch (1).
NHIL13AF00586AA 7
33. Disconnect the fuel pump wire connector (1) to disable
the fuel pump (2).
NHIL14AF00745AA 8
34. Check the engine oil level and top off if necessary.
35. Crank the engine over for three ten second intervals.
This will distribute lubricating oil to the engine oper-
ating systems and will allow oil pressure to be built
before starting the engine.
36. Connect the fuel pump wire connector (1) to the fuel
pump (2) and bleed the air from fuel injection system,
as described in the Operators manual.
37. Start the engine and check all hoses, fittings and
clamps for leaks.
NOTICE: Monitor the instrument warning light bar at all
times during initial engine start up to ensure the engine has
proper oil pressure. Shut down the engine immediately if
oil pressure is not adequate.
38. Ensure all electrical components are working properly.
NHIL14AF00745AA 9
51586252 07/03/2019
10.1 [10.001] / 9
22. Engine - Engine and crankcase
Engine - Remove
AXIAL-FLOW® 9250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
Prior operation:
Engine - Remove engine oil drain line and drain valve (10.001)
Prior operation:
Radiator - Drain fluid (10.400)
Prior operation:
Deaeration tank - Remove (10.400)
Prior operation:
Air conditioning - Service instruction (50.200)
Prior operation:
Air intake system - Remove (10.202)
Prior operation:
Engine shield - Remove (90.102)
Prior operation:
Radiator hoses - Remove (10.400)
Prior operation:
Central wiring harness - Remove (55.100)
Prior operation:
Aftercooler air supply and return lines - Remove air supply tube (10.310)
Prior operation:
Aftercooler air supply and return lines - Remove air return tube (10.310)
Prior operation:
Connection tube from filter to muffler - Remove (10.202)
Prior operation:
Air-conditioning compressor - Remove (from Cursor 13 and 16 engine) (50.200)
Prior operation:
Fuel supply lines Low pressure - Remove from the engine (10.210)
Prior operation:
Fuel return lines - Remove from the engine (10.210)
Prior operation:
Exhaust muffler - Remove mixer tube (10.254)
Prior operation:
Exhaust muffler - Remove exhaust tube from turbo charger to Diesel Oxidation Catalyst (DOC) (10.254)
Prior operation:
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA lines - Remove DEF hose bundle from the engine compartment
(10.500)
Prior operation:
Selective Catalytic Reduction (SCR) muffler and catalyst - Remove (10.500)
Prior operation:
Diesel Oxidation Catalyst (DOC) - Remove (10.500)
51586252 07/03/2019
10.1 [10.001] / 10
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Engine - Engine and crankcase
NOTE: Illustrations are for reference only. It may not be the actual engine.
1. Disengage the battery connect switch (1).
NHIL13AF00586AA 1
2. Attach a suitable chain to the front lift eye (1) at the front
of the engine.
NHIL14AF00431AA 2
3. Attach a suitable chain to the back lift eye (1) at the rear
of the engine.
86070260 3
51586252 07/03/2019
10.1 [10.001] / 11
25. Engine - Engine and crankcase
4. Connect the lift chain to a suitable lifting device.
5. Raise the lifting device enough to support the engine
during removal of the engine mounting bolts.
NOTE: Illustration is for reference only. It may not be the
actual engine.
NOTE: The lifting device should be rated for at least
907.2 kg (2000 lb). Allow enough clearance to lift the
engine from the combine, approximately 7.0 m (23 ft) from
the floor.
10013136 4
6. From the grain tank side of engine, loosen the front two
engine mounting bolts (1). Do not remove the mounting
bolts at this time.
7. From the platform side, loosen the two front, engine
mounting bolts (2). Do not remove the mounting bolts
at this time.
NHIL14AF01003AA 5
8. Loosen but do not remove all the bolts and washers (1)
that couple the engine to the gearbox. There are twelve
bolts and washers in total.
9. For safety reasons to the radiators, place a sheet of
plywood, cut to size, in front of the cooler box for pro-
tection.
10. With the engine securely supported by the lifting de-
vice, remove all of the engine mounting bolts and the
engine to the gearbox coupling bolts that were loos-
ened in the previous steps.
11. Slide the engine towards the cooler box to disengage
the flex plate from the gearbox input shaft.
12. Carefully lift the engine from the frame and remove
from the combine.
NHIL14AF01005AA 6
Next operation:
Engine - Install (10.001)
51586252 07/03/2019
10.1 [10.001] / 12
26. Engine - Engine and crankcase
Engine - Install
AXIAL-FLOW® 9250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
NOTE: Illustrations are for reference only. It may not be the actual engine.
1. Before installing the engine, apply LOCTITE® SILVER
GRADE ANTI-SEIZE to the input shaft (1) of the gearbox.
83070284 1
2. Attach a suitable chain to the front lift eye (1) at the front
of the engine.
86070259 2
51586252 07/03/2019
10.1 [10.001] / 13