This document is a service manual for the Case IH Axial-Flow 7250, 8250, and 9250 combines with Tier 4B engines. It provides an introduction and table of contents that lists over 55 sections covering all major vehicle systems, including the engine, transmission, axles, hydraulics, steering, electrical systems, and cab climate control. Each section number links to detailed information, specifications, diagrams and procedures for servicing and repairing components within that system.
New holland t8.380 powershift transmission (pst) tractor service repair manua...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland t8.380 pst tier 4 b tractor service repair manual [zhre04001 ]ufjjjsksekemme
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing cooling and emissions systems components before disconnecting engine sensors, tubes, and hoses and removing the intake tube. Caps or plugs must be installed when disconnecting hydraulic lines.
New holland t8.410 smart trax™ powershift transmission (pst) tractor service ...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains detailed sections for servicing and repairing components of the tractors. The manual begins with an introduction and table of contents that lists the major vehicle systems and corresponding section numbers for finding repair information.
New holland t8.350 powershift transmission (pst) tractor service repair manua...usjekkmdmd
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing engine cooling and emissions components before disconnecting hoses, tubes, sensors, and harnesses from the engine.
New holland t8.320 powershift transmission (pst) tractor service repair manua...yhfhjjssennea
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland 8670 a tractor service repair manualfujskekskemm
This document is a repair manual section covering the engine and lubrication system for a New Holland 70/70A series tractor. It includes specifications, torque values, grease and sealant types, special tools, descriptions of engine operation and components. The section contains information on disassembly and inspection of the cylinder head, camshaft, crankshaft, connecting rods, pistons, manifolds, cylinder block, and timing gears. It also describes the engine lubrication system.
Massey ferguson mf3120 t tractor service parts catalogue manual (part number ...fujskekskemm
1. The document provides a parts list and descriptions for the cylinder block of a Massey Ferguson T6.60 engine used in MF 3120/3120T tractors. It includes items like the cylinder block, caps, liners, rings, screws, plugs, bushings, washers, and gaskets.
2. The parts list then details the crankshaft, pistons, connecting rods, bearings, thrust washers, conrod kits, pistons, pins, circlips, and piston ring kits for the engine. It also lists gears, keys, pulleys, spacers, plates, screws, dampers, and more.
3. The final section
Massey ferguson 4235 tractors ( k37008) service parts catalogue manual (part...fujskekskemm
1. The document provides parts lists and technical specifications for cylinder blocks, crankshafts, pistons, and connecting rods for Massey Ferguson 4225, 4235, and 4240 tractors.
2. It lists over 40 individual parts with part numbers, quantities, descriptions, and other identifying information. Footnotes provide additional details on some part specifications.
3. The parts lists are broken into sections based on the specific tractor model and engine build details, with references to other sections for additional information.
New holland t8.380 powershift transmission (pst) tractor service repair manua...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland t8.380 pst tier 4 b tractor service repair manual [zhre04001 ]ufjjjsksekemme
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing cooling and emissions systems components before disconnecting engine sensors, tubes, and hoses and removing the intake tube. Caps or plugs must be installed when disconnecting hydraulic lines.
New holland t8.410 smart trax™ powershift transmission (pst) tractor service ...usjekkmdmd
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains detailed sections for servicing and repairing components of the tractors. The manual begins with an introduction and table of contents that lists the major vehicle systems and corresponding section numbers for finding repair information.
New holland t8.350 powershift transmission (pst) tractor service repair manua...usjekkmdmd
The document provides instructions for removing an engine and crankcase from various New Holland tractor models for service or replacement. Key steps include disconnecting batteries, removing the hood and side shields, recovering refrigerant, draining coolant, and removing engine cooling and emissions components before disconnecting hoses, tubes, sensors, and harnesses from the engine.
New holland t8.320 powershift transmission (pst) tractor service repair manua...yhfhjjssennea
This document is a service manual for New Holland T8 series tractors that provides information on engine systems, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, and electrical systems. It contains over 50 sections that describe the components, operation, and servicing of these tractor systems. The manual is intended to assist technicians with maintenance and repairs.
New holland 8670 a tractor service repair manualfujskekskemm
This document is a repair manual section covering the engine and lubrication system for a New Holland 70/70A series tractor. It includes specifications, torque values, grease and sealant types, special tools, descriptions of engine operation and components. The section contains information on disassembly and inspection of the cylinder head, camshaft, crankshaft, connecting rods, pistons, manifolds, cylinder block, and timing gears. It also describes the engine lubrication system.
Massey ferguson mf3120 t tractor service parts catalogue manual (part number ...fujskekskemm
1. The document provides a parts list and descriptions for the cylinder block of a Massey Ferguson T6.60 engine used in MF 3120/3120T tractors. It includes items like the cylinder block, caps, liners, rings, screws, plugs, bushings, washers, and gaskets.
2. The parts list then details the crankshaft, pistons, connecting rods, bearings, thrust washers, conrod kits, pistons, pins, circlips, and piston ring kits for the engine. It also lists gears, keys, pulleys, spacers, plates, screws, dampers, and more.
3. The final section
Massey ferguson 4235 tractors ( k37008) service parts catalogue manual (part...fujskekskemm
1. The document provides parts lists and technical specifications for cylinder blocks, crankshafts, pistons, and connecting rods for Massey Ferguson 4225, 4235, and 4240 tractors.
2. It lists over 40 individual parts with part numbers, quantities, descriptions, and other identifying information. Footnotes provide additional details on some part specifications.
3. The parts lists are broken into sections based on the specific tractor model and engine build details, with references to other sections for additional information.
Massey ferguson 399 tractor ( 1006.6 engine ) service parts catalogue manual ...fujskekskemm
This document provides parts information for the engine of a Massey Ferguson 399 tractor with a 1006.6 engine. It includes lists of parts with part numbers, quantities, and descriptions for the engine block, crankshaft, pistons, connecting rods, cylinder head, and other engine components. Footnotes provide additional information on some part numbers and specifications.
Massey ferguson 372 n tractor service parts catalogue manual (part number 81...fujskekskemm
This document provides part numbers and descriptions for engine components of a Massey Ferguson 372 N tractor. It includes listings for the engine block, cylinder head, crankshaft, pistons, and other internal engine parts. Measurements and serial number ranges are provided for some components. The document appears to be a partial exploded diagram and parts list for the engine.
Massey ferguson 362 tractor service parts catalogue manual (part number 819779)fujskekskemm
This document provides part numbers and descriptions for engine components of a Massey Ferguson 362 tractor. It includes lists of parts for the engine, cylinder block, crankshaft, cylinder head, and other systems. Quantities, part numbers, descriptions, and other identifying information are provided for over 60 individual parts.
Kubota v2403 m-di diesel engine service repair manualfujskekskemm
This document provides specifications for several Kubota diesel engine models. It includes information on displacement, power output, operating speed, lubrication system, cooling system, and dimensions. The specifications cover single-cylinder, three-cylinder, and four-cylinder engine configurations with power ratings ranging from 20kW to 44kW. Performance data such as fuel injection details and compression ratios are also listed for each model.
John deere z355 e z trak mower (s.n.010001-) service repair technical manual ...fujskekskemm
The document provides instructions for removing and installing an engine on a ZTrak mower. It involves disconnecting wiring, fuel lines, belts, and removing mounting bolts. The engine is then installed by reversing these steps and reconnecting all components. Tightening specifications are provided for mounting bolts and other fasteners. Safety cautions are included for fuel, belts, and hot surfaces.
John deere x115 r riding lawn tractor service repair technical manual (tm113419)fujskekskemm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
John deere x105 lawn tractor service repair technical manual (tm113319)fujskekskemm
This document provides safety information for technicians working on X105, X125, X145, X165, and 107S tractors. It outlines various hazards including battery explosions, acid burns, fire risks, and more. Technicians are instructed to take safety precautions like wearing protective equipment, working in ventilated areas, and avoiding sparks or flames when working with batteries. The document also provides first aid instructions for dealing with acid exposures.
John deere power tech 12.5l diesel base engine service repair technical manua...fujskekskemm
1) The document provides instructions for removing and installing a rocker arm cover on a diesel engine, including removing mounting hardware and isolators, lifting off the cover, and reinstalling in reverse order while checking unit injector wiring routing.
2) Additional instructions are given for cleaning and inspecting the crankcase ventilation assembly, replacing the rocker arm cover gasket, and checking/adjusting valve clearances and injector preload while the engine is locked at specific timing positions using timing pins.
3) Precise torque specifications are listed for tightening cover mounting hardware and valve/injector adjustment components. Thorough inspection of all valve bridges and stems is emphasized to prevent engine failure.
John deere 328 d skid steer loader (manual controls) service repair manual (t...fujskekskemm
This document provides instructions for disassembling and assembling a track adjuster cylinder. It describes how to safely remove the recoil spring and disassemble the cylinder components like seals and rods. Precautions are outlined to prevent damage to parts. The proper process for cleaning, inspecting, and reinstalling components in reverse order is described. Torque specifications and measurements are provided for correctly assembling and setting the preload on the cylinder.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fujskekskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms and push rods before removing the head and gasket.
John deere 27 d compact excavator service repair technical manual (tm2356)fujskekskemm
1. The document provides instructions for removing and installing an engine on an excavator. It describes disconnecting components like fuel lines, electrical connections, and mounts before lifting the engine out with a sling. It then describes installing the engine and reconnecting all components.
2. The instructions describe removing and installing an exhaust manifold on the excavator. Components like nuts, bolts and gaskets are removed and replaced to access the manifold.
3. The document provides steps for removing and installing a muffler, including removing brackets and heat shields to access the muffler connection to the exhaust manifold.
The document provides instructions for removing the ejector blade floor rollers from a 740 Ejector Articulated Truck. The procedure involves positioning the ejector blade halfway in the truck body, loosening nuts on bolts on both sides of the ejector, and turning the bolts to remove the floor rollers. Cleanliness is important to prevent dirt from entering during removal. The same process is used to remove the remaining three floor rollers.
This document provides instructions for removing and installing a steering cylinder on a 740 Ejector Articulated Truck. The removal process involves using tools to remove pins and brackets connecting the cylinder to the frame. Pressure must be relieved before disassembly. Installation requires cleaning, lubricating, and replacing any worn parts before reattaching the cylinder using the pins and brackets. Proper torque values must be applied to fasteners.
The document provides instructions for disassembling and assembling the gear pump used for the hydraulic fan on a 740 Articulated Truck. To disassemble the pump, fittings and seals are removed from the pump body and flange. The flange is then separated from the pump body by removing nuts and washers. Seals are also removed from the flange. Proper cleaning and inspection of parts is required before assembly.
Caterpillar cat 320 e rr excavator (prefix lhn) service repair manual (lhn000...fujskekskemm
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 320E excavator.
The flywheel removal procedure involves removing bolts and installing guide studs to support the flywheel weight before lifting it off. The installation procedure specifies cleaning and orienting the ring gear if replaced, and torquing bolts to 140 N·m.
The crankshaft rear seal removal requires removing Torx screws using two socket tools. Installation specifies using a new seal assembly and not lubricating the seal or crankshaft flange during dry installation.
Caterpillar cat 320 e lrr excavator (prefix lhn) service repair manual (lhn00...fujskekskemm
The document provides instructions for removing and installing a flywheel on Caterpillar 320E RR and 320E LRR excavator models powered by a C6.6 engine. The removal procedure involves removing mounting bolts and installing guide studs to lift the flywheel off. The flywheel and ring gear are inspected for wear. To install, the ring gear is heated and mounted if replaced, bolts are used to mount the flywheel while being lifted, and bolts are tightened to the specified torque.
Caterpillar cat 257 multi terrain loader (prefix cmm) service repair manual (...fujskekskemm
This document provides instructions for removing and installing various components of a 3034 engine, including:
- Removing the flywheel by drilling holes in it and lifting it off with a bracket and lifting device.
- Removing the flywheel ring gear by checking its teeth and tapping it off the flywheel with a punch.
- Removing the crankshaft rear seal by drilling holes in it and pulling it out with a slide hammer tool.
- Removing the flywheel housing by detaching it with brackets and lifting devices after removing mounting bolts.
- Removing the crankshaft pulley by loosening an alternator, removing a bolt and washer, and lifting the pulley off.
Caterpillar cat 256 c skid steer loader (prefix dws) service repair manual (d...fujskekskemm
The document provides instructions for disassembling and assembling the piston pump (hydrostatic) of a 256C Skid Steer Loader. The disassembly procedure involves removing components like valves, coils, cartridges, seals and O-rings. The assembly procedure instructs to install these components in the reverse order and apply thread lock compound and heat bearings during assembly. Precise measurements are required to center the swashplate.
Case ih steiger 500 qt tractor service repair manual [zdf100001 ]fujskekskemm
This document is a service manual for Steiger tractors models 350, 400, 450, 500, 550, and 600 and Quadtrac models 450, 500, 550, and 600. It contains safety information and instructions for servicing various components of the tractors, including the engine, transmission, axles, brakes, hydraulics, steering, wheels, tracks, cab, electrical systems, and other parts. The manual is divided into sections covering each major system.
Case ih steiger 450 tractor service repair manual [zcf100001 ]fujskekskemm
This document is a service manual for Steiger tractors models 350, 400, 450, 500, 550, and 600 and Quadtrac models 450, 500, 550, and 600. It contains safety information and instructions for servicing various components of the tractors, including the engine, transmission, axles, brakes, hydraulics, steering, wheels, tracks, cab, electrical systems, and other parts. The manual is divided into sections covering each major system.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Massey ferguson 399 tractor ( 1006.6 engine ) service parts catalogue manual ...fujskekskemm
This document provides parts information for the engine of a Massey Ferguson 399 tractor with a 1006.6 engine. It includes lists of parts with part numbers, quantities, and descriptions for the engine block, crankshaft, pistons, connecting rods, cylinder head, and other engine components. Footnotes provide additional information on some part numbers and specifications.
Massey ferguson 372 n tractor service parts catalogue manual (part number 81...fujskekskemm
This document provides part numbers and descriptions for engine components of a Massey Ferguson 372 N tractor. It includes listings for the engine block, cylinder head, crankshaft, pistons, and other internal engine parts. Measurements and serial number ranges are provided for some components. The document appears to be a partial exploded diagram and parts list for the engine.
Massey ferguson 362 tractor service parts catalogue manual (part number 819779)fujskekskemm
This document provides part numbers and descriptions for engine components of a Massey Ferguson 362 tractor. It includes lists of parts for the engine, cylinder block, crankshaft, cylinder head, and other systems. Quantities, part numbers, descriptions, and other identifying information are provided for over 60 individual parts.
Kubota v2403 m-di diesel engine service repair manualfujskekskemm
This document provides specifications for several Kubota diesel engine models. It includes information on displacement, power output, operating speed, lubrication system, cooling system, and dimensions. The specifications cover single-cylinder, three-cylinder, and four-cylinder engine configurations with power ratings ranging from 20kW to 44kW. Performance data such as fuel injection details and compression ratios are also listed for each model.
John deere z355 e z trak mower (s.n.010001-) service repair technical manual ...fujskekskemm
The document provides instructions for removing and installing an engine on a ZTrak mower. It involves disconnecting wiring, fuel lines, belts, and removing mounting bolts. The engine is then installed by reversing these steps and reconnecting all components. Tightening specifications are provided for mounting bolts and other fasteners. Safety cautions are included for fuel, belts, and hot surfaces.
John deere x115 r riding lawn tractor service repair technical manual (tm113419)fujskekskemm
1. The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors.
2. Key steps include removing the hood, drive belt, wiring harness, fuel lines, and mounting bolts to remove the engine. Reinstallation is the reverse of removal.
3. Removing and installing the cylinder head requires marking push rods, removing the valve cover, rocker arms, and head bolts before removing the head and installing the new gasket.
John deere x105 lawn tractor service repair technical manual (tm113319)fujskekskemm
This document provides safety information for technicians working on X105, X125, X145, X165, and 107S tractors. It outlines various hazards including battery explosions, acid burns, fire risks, and more. Technicians are instructed to take safety precautions like wearing protective equipment, working in ventilated areas, and avoiding sparks or flames when working with batteries. The document also provides first aid instructions for dealing with acid exposures.
John deere power tech 12.5l diesel base engine service repair technical manua...fujskekskemm
1) The document provides instructions for removing and installing a rocker arm cover on a diesel engine, including removing mounting hardware and isolators, lifting off the cover, and reinstalling in reverse order while checking unit injector wiring routing.
2) Additional instructions are given for cleaning and inspecting the crankcase ventilation assembly, replacing the rocker arm cover gasket, and checking/adjusting valve clearances and injector preload while the engine is locked at specific timing positions using timing pins.
3) Precise torque specifications are listed for tightening cover mounting hardware and valve/injector adjustment components. Thorough inspection of all valve bridges and stems is emphasized to prevent engine failure.
John deere 328 d skid steer loader (manual controls) service repair manual (t...fujskekskemm
This document provides instructions for disassembling and assembling a track adjuster cylinder. It describes how to safely remove the recoil spring and disassemble the cylinder components like seals and rods. Precautions are outlined to prevent damage to parts. The proper process for cleaning, inspecting, and reinstalling components in reverse order is described. Torque specifications and measurements are provided for correctly assembling and setting the preload on the cylinder.
John deere 107 h riding lawn tractor service repair technical manual (tm113419)fujskekskemm
The document provides instructions to remove and install a single cylinder engine on X115R, X135R, X155R, 92H, and 107H tractors. The key steps include:
1. Disconnecting wiring, removing the drive belt, fuel lines, and mounting bolts to remove the engine.
2. Reversing the removal steps to install the engine, reconnecting wiring and fuel lines and securing with mounting bolts.
3. Removing the cylinder head requires taking off additional parts like the valve cover, rocker arms and push rods before removing the head and gasket.
John deere 27 d compact excavator service repair technical manual (tm2356)fujskekskemm
1. The document provides instructions for removing and installing an engine on an excavator. It describes disconnecting components like fuel lines, electrical connections, and mounts before lifting the engine out with a sling. It then describes installing the engine and reconnecting all components.
2. The instructions describe removing and installing an exhaust manifold on the excavator. Components like nuts, bolts and gaskets are removed and replaced to access the manifold.
3. The document provides steps for removing and installing a muffler, including removing brackets and heat shields to access the muffler connection to the exhaust manifold.
The document provides instructions for removing the ejector blade floor rollers from a 740 Ejector Articulated Truck. The procedure involves positioning the ejector blade halfway in the truck body, loosening nuts on bolts on both sides of the ejector, and turning the bolts to remove the floor rollers. Cleanliness is important to prevent dirt from entering during removal. The same process is used to remove the remaining three floor rollers.
This document provides instructions for removing and installing a steering cylinder on a 740 Ejector Articulated Truck. The removal process involves using tools to remove pins and brackets connecting the cylinder to the frame. Pressure must be relieved before disassembly. Installation requires cleaning, lubricating, and replacing any worn parts before reattaching the cylinder using the pins and brackets. Proper torque values must be applied to fasteners.
The document provides instructions for disassembling and assembling the gear pump used for the hydraulic fan on a 740 Articulated Truck. To disassemble the pump, fittings and seals are removed from the pump body and flange. The flange is then separated from the pump body by removing nuts and washers. Seals are also removed from the flange. Proper cleaning and inspection of parts is required before assembly.
Caterpillar cat 320 e rr excavator (prefix lhn) service repair manual (lhn000...fujskekskemm
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 320E excavator.
The flywheel removal procedure involves removing bolts and installing guide studs to support the flywheel weight before lifting it off. The installation procedure specifies cleaning and orienting the ring gear if replaced, and torquing bolts to 140 N·m.
The crankshaft rear seal removal requires removing Torx screws using two socket tools. Installation specifies using a new seal assembly and not lubricating the seal or crankshaft flange during dry installation.
Caterpillar cat 320 e lrr excavator (prefix lhn) service repair manual (lhn00...fujskekskemm
The document provides instructions for removing and installing a flywheel on Caterpillar 320E RR and 320E LRR excavator models powered by a C6.6 engine. The removal procedure involves removing mounting bolts and installing guide studs to lift the flywheel off. The flywheel and ring gear are inspected for wear. To install, the ring gear is heated and mounted if replaced, bolts are used to mount the flywheel while being lifted, and bolts are tightened to the specified torque.
Caterpillar cat 257 multi terrain loader (prefix cmm) service repair manual (...fujskekskemm
This document provides instructions for removing and installing various components of a 3034 engine, including:
- Removing the flywheel by drilling holes in it and lifting it off with a bracket and lifting device.
- Removing the flywheel ring gear by checking its teeth and tapping it off the flywheel with a punch.
- Removing the crankshaft rear seal by drilling holes in it and pulling it out with a slide hammer tool.
- Removing the flywheel housing by detaching it with brackets and lifting devices after removing mounting bolts.
- Removing the crankshaft pulley by loosening an alternator, removing a bolt and washer, and lifting the pulley off.
Caterpillar cat 256 c skid steer loader (prefix dws) service repair manual (d...fujskekskemm
The document provides instructions for disassembling and assembling the piston pump (hydrostatic) of a 256C Skid Steer Loader. The disassembly procedure involves removing components like valves, coils, cartridges, seals and O-rings. The assembly procedure instructs to install these components in the reverse order and apply thread lock compound and heat bearings during assembly. Precise measurements are required to center the swashplate.
Case ih steiger 500 qt tractor service repair manual [zdf100001 ]fujskekskemm
This document is a service manual for Steiger tractors models 350, 400, 450, 500, 550, and 600 and Quadtrac models 450, 500, 550, and 600. It contains safety information and instructions for servicing various components of the tractors, including the engine, transmission, axles, brakes, hydraulics, steering, wheels, tracks, cab, electrical systems, and other parts. The manual is divided into sections covering each major system.
Case ih steiger 450 tractor service repair manual [zcf100001 ]fujskekskemm
This document is a service manual for Steiger tractors models 350, 400, 450, 500, 550, and 600 and Quadtrac models 450, 500, 550, and 600. It contains safety information and instructions for servicing various components of the tractors, including the engine, transmission, axles, brakes, hydraulics, steering, wheels, tracks, cab, electrical systems, and other parts. The manual is divided into sections covering each major system.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
10. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
51586252 07/03/2019
3
11. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
51586252 07/03/2019
4
12. INTRODUCTION
Personal safety
WARNING
Risk of harm during maintenance of the machine!
Before you start servicing the machine, attach a DO NOT OPERATE warning tag to the machine in a
visible area.
Failure to comply could result in death or serious injury.
W1242A
Attach a DO NOT OPERATE (TAG) to the machine in an area that is clearly visible whenever the machine is not
operating properly and/or requires service.
Complete the tag information for the "REASON" the tag is attached by describing the malfunction or service required.
Validate the reason for attaching the tag by signing your name in the designated area on the tag.
The tag should only be removed by the person who signed and attached the tag, after validating the repairs or services
have been completed.
51586252 07/03/2019
5
15. Engine - Engine and crankcase
Engine - Remove
AXIAL-FLOW® 7250
AXIAL-FLOW® 8250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
Prior operation:
Remove the oil drain hose. See Engine - Remove engine oil drain line and drain valve (10.001)
Prior operation:
Radiator - Drain fluid (10.400)
Prior operation:
Deaeration tank - Remove (10.400)
Prior operation:
Engine shield - Remove (90.102)
Prior operation:
Radiator hoses - Remove (10.400)
Prior operation:
Central wiring harness - Remove (55.100)
Prior operation:
Aftercooler air supply and return lines - Remove air supply tube (10.310)
Prior operation:
Aftercooler air supply and return lines - Remove air return tube (10.310)
Prior operation:
Air cleaner connection between filter and engine - Remove - Axial-Flow® 7250 and Axial-Flow® 8250 (10.202)
Prior operation:
Connection tube from filter to muffler - Remove (10.202)
Prior operation:
Fan - Remove (10.414)
Prior operation:
Air-conditioning compressor - Remove (from Cursor 11 Engine) (50.200)
Prior operation:
Fuel supply lines Low pressure - Remove from the engine (10.210)
Prior operation:
Fuel return lines - Remove from the engine (10.210)
Prior operation:
Exhaust muffler - Remove mixer tube (10.254)
Prior operation:
Exhaust muffler - Remove exhaust tube from turbo charger to Diesel Oxidation Catalyst (DOC) (10.254)
Prior operation:
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA lines - Remove DEF hose bundle from the engine compartment
(10.500)
Prior operation:
Selective Catalytic Reduction (SCR) muffler and catalyst - Remove (10.500)
Prior operation:
51586252 07/03/2019
10.1 [10.001] / 3
16. Engine - Engine and crankcase
Diesel Oxidation Catalyst (DOC) - Remove (10.500)
1. Disengage the battery connect switch (1).
NHIL13AF00586AA 1
2. Attach a suitable lift chain to the front lift eye (1) at the
front of the engine.
NHIL14AF00431AA 2
3. Attach a suitable lift chain to the back lift eye (1) at the
rear of the engine.
NHIL14AF00432AA 3
51586252 07/03/2019
10.1 [10.001] / 4
17. Engine - Engine and crankcase
4. Connect the lift chain to a suitable lifting device.
5. Raise the lifting device enough to support the engine
during removal of the engine mounting bolts.
NOTE: The lifting device should be rated for at least
907.2 kg (2000 lb). Allow enough clearance to lift the
engine from the combine, approximately 7.0 m (23 ft) from
the floor.
10013136 4
6. From the grain tank side of the engine, loosen the front,
engine mounting bolts (1). Do not remove the mounting
bolts at this time.
7. From the platform side, loosen the front, engine mount-
ing bolts (2). Do not remove the mounting bolts at this
time.
NHIL14AF01001AA 5
8. From the rear of the engine, loosen but do not remove
all the bolts and washers (1) that couple the engine to
the gearbox. There are twelve bolts and washers in
total.
9. For safety reasons to the radiators, place a sheet of
plywood, cut to size, in front of the cooler box for pro-
tection.
10. With the engine securely supported by the lifting de-
vice, remove all of the engine mounting bolts and the
engine to the gearbox coupling bolts that were loos-
ened in the previous steps.
11. Slide the engine towards the cooler box to disengage
the flex plate from the gearbox input shaft.
12. Carefully lift the engine from the frame and remove
from the combine. NHIL14AF01004AA 6
Next operation:
Engine - Install (10.001) .
51586252 07/03/2019
10.1 [10.001] / 5
18. Engine - Engine and crankcase
Engine - Install
AXIAL-FLOW® 7250
AXIAL-FLOW® 8250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
NOTE: Illustrations are for reference only. It may not be the actual engine.
1. Before installing the engine, apply LOCTITE® SILVER
GRADE ANTI-SEIZE to the input shaft (1) of the gearbox.
83070284 1
2. Attach a suitable chain to the front lift eye (1) at the front
of the engine.
86070259 2
51586252 07/03/2019
10.1 [10.001] / 6
19. Engine - Engine and crankcase
3. Attach a suitable chain to the back lift eye (1) at the rear
of the engine.
86070260 3
4. Connect the lift chain to a suitable lifting device.
5. Carefully lift the engine above the combine and lower
into position in the frame.
NOTE: The lifting device should be rated for at least
907.2 kg (2000 lb). Allow enough clearance to lift the en-
gine from the combine, approximately 907.2 kg (2000 lb)
from the floor.
10013136 4
6. For safety reasons to the radiator, place a sheet of ply-
wood, cut to size, in front of the radiator for protection.
7. Slide the engine towards the gearbox onto the gear box
input shaft.
8. Align the holes of the gearbox with the engine and hand
start a bolt with a washer (1) on each side of the cou-
pling, going back and forth until all bolts with a washers
are installed.
NHIL14AF01004AA 5
51586252 07/03/2019
10.1 [10.001] / 7
20. Engine - Engine and crankcase
9. With the engine positioned in the frame, align the front
mounting hole on the grain tank side and install the bolt
with washers (1) into the mount. Do not tighten yet.
10. Align the front mounting hole on the platform side. In-
stall the bolt with washers (1) into the mount.
11. Tighten and torque the front engine mounting bolts to
217 Nm (160.1 lb ft).
12. Tighten and torque the engine gearbox bolts to 41 –
51 Nm (30.2 – 37.6 lb ft).
NHIL14AF01001AA 6
13. Diesel Oxidation Catalyst (DOC) - Install (10.500)
14. Selective Catalytic Reduction (SCR) muffler and
catalyst - Remove (10.500)
15. Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA lines -
Install DEF hose bundle from the engine compart-
ment (10.500)
16. Exhaust muffler - Install exhaust tube from
turbo charger to Diesel Oxidation Catalyst (DOC)
(10.254)
17. Exhaust muffler - Install mixer tube (10.254)
18. Fuel return lines - Install to the engine (10.210)
19. Fuel supply lines Low pressure - Install to the en-
gine (10.210)
20. Air-conditioning compressor - Install (on Cursor
11 Engine) (50.200)
21. Fan - Install (10.414)
22. Connection tube from filter to muffler - Install
(10.202)
23. Air cleaner connection between filter and engine -
Install - Axial-Flow® 9250 (10.202)
24. Aftercooler air supply and return lines - Install air
return tube (10.310)
25. Aftercooler air supply and return lines - Install air
supply tube (10.310)
26. Central wiring harness - Install (55.100)
27. Radiator hoses - Install (10.400)
28. Engine shield - Install (90.102)
29. Deaeration tank - Install (10.400)
30. Radiator - Filling (10.400)
31. Engine - Install engine oil drain line and drain
valve (10.001)
51586252 07/03/2019
10.1 [10.001] / 8
21. Engine - Engine and crankcase
32. Engage the battery connect switch (1).
NHIL13AF00586AA 7
33. Disconnect the fuel pump wire connector (1) to disable
the fuel pump (2).
NHIL14AF00745AA 8
34. Check the engine oil level and top off if necessary.
35. Crank the engine over for three ten second intervals.
This will distribute lubricating oil to the engine oper-
ating systems and will allow oil pressure to be built
before starting the engine.
36. Connect the fuel pump wire connector (1) to the fuel
pump (2) and bleed the air from fuel injection system,
as described in the Operators manual.
37. Start the engine and check all hoses, fittings and
clamps for leaks.
NOTICE: Monitor the instrument warning light bar at all
times during initial engine start up to ensure the engine has
proper oil pressure. Shut down the engine immediately if
oil pressure is not adequate.
38. Ensure all electrical components are working properly.
NHIL14AF00745AA 9
51586252 07/03/2019
10.1 [10.001] / 9
22. Engine - Engine and crankcase
Engine - Remove
AXIAL-FLOW® 9250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
Prior operation:
Engine - Remove engine oil drain line and drain valve (10.001)
Prior operation:
Radiator - Drain fluid (10.400)
Prior operation:
Deaeration tank - Remove (10.400)
Prior operation:
Air conditioning - Service instruction (50.200)
Prior operation:
Air intake system - Remove (10.202)
Prior operation:
Engine shield - Remove (90.102)
Prior operation:
Radiator hoses - Remove (10.400)
Prior operation:
Central wiring harness - Remove (55.100)
Prior operation:
Aftercooler air supply and return lines - Remove air supply tube (10.310)
Prior operation:
Aftercooler air supply and return lines - Remove air return tube (10.310)
Prior operation:
Connection tube from filter to muffler - Remove (10.202)
Prior operation:
Air-conditioning compressor - Remove (from Cursor 13 and 16 engine) (50.200)
Prior operation:
Fuel supply lines Low pressure - Remove from the engine (10.210)
Prior operation:
Fuel return lines - Remove from the engine (10.210)
Prior operation:
Exhaust muffler - Remove mixer tube (10.254)
Prior operation:
Exhaust muffler - Remove exhaust tube from turbo charger to Diesel Oxidation Catalyst (DOC) (10.254)
Prior operation:
Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA lines - Remove DEF hose bundle from the engine compartment
(10.500)
Prior operation:
Selective Catalytic Reduction (SCR) muffler and catalyst - Remove (10.500)
Prior operation:
Diesel Oxidation Catalyst (DOC) - Remove (10.500)
51586252 07/03/2019
10.1 [10.001] / 10
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Engine - Engine and crankcase
NOTE: Illustrations are for reference only. It may not be the actual engine.
1. Disengage the battery connect switch (1).
NHIL13AF00586AA 1
2. Attach a suitable chain to the front lift eye (1) at the front
of the engine.
NHIL14AF00431AA 2
3. Attach a suitable chain to the back lift eye (1) at the rear
of the engine.
86070260 3
51586252 07/03/2019
10.1 [10.001] / 11
25. Engine - Engine and crankcase
4. Connect the lift chain to a suitable lifting device.
5. Raise the lifting device enough to support the engine
during removal of the engine mounting bolts.
NOTE: Illustration is for reference only. It may not be the
actual engine.
NOTE: The lifting device should be rated for at least
907.2 kg (2000 lb). Allow enough clearance to lift the
engine from the combine, approximately 7.0 m (23 ft) from
the floor.
10013136 4
6. From the grain tank side of engine, loosen the front two
engine mounting bolts (1). Do not remove the mounting
bolts at this time.
7. From the platform side, loosen the two front, engine
mounting bolts (2). Do not remove the mounting bolts
at this time.
NHIL14AF01003AA 5
8. Loosen but do not remove all the bolts and washers (1)
that couple the engine to the gearbox. There are twelve
bolts and washers in total.
9. For safety reasons to the radiators, place a sheet of
plywood, cut to size, in front of the cooler box for pro-
tection.
10. With the engine securely supported by the lifting de-
vice, remove all of the engine mounting bolts and the
engine to the gearbox coupling bolts that were loos-
ened in the previous steps.
11. Slide the engine towards the cooler box to disengage
the flex plate from the gearbox input shaft.
12. Carefully lift the engine from the frame and remove
from the combine.
NHIL14AF01005AA 6
Next operation:
Engine - Install (10.001)
51586252 07/03/2019
10.1 [10.001] / 12
26. Engine - Engine and crankcase
Engine - Install
AXIAL-FLOW® 9250
WARNING
Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.
W0047A
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
NOTE: Illustrations are for reference only. It may not be the actual engine.
1. Before installing the engine, apply LOCTITE® SILVER
GRADE ANTI-SEIZE to the input shaft (1) of the gearbox.
83070284 1
2. Attach a suitable chain to the front lift eye (1) at the front
of the engine.
86070259 2
51586252 07/03/2019
10.1 [10.001] / 13