3. 3
Standards:
∙ ASTM A-269 / A270S2
∙ ASME BPE
Surface Finish:
Surface fi nish specifi cations are the same for fi ttings & tubes.
Please refer to table SF-3 on page 3.
Tubing Dimension & Tolerances:
Tubing specifi cations, ASTM A-269/A270S2
Tube Specifications
O.D. Gauge O.D. Dimensional Length Wall Thickness
Tubing Diameter (wall thickness) Specification Size & Tolerances
Inch mm Inch mm ASTM Spec. ASTM Spec. ASTM Spec.
½" 12,7 16G +.005/-.005 +1/8 0.065 +/-10 %
(.065"/1,65 mm wall)
¾" 19,0 16G +.005/-.005 +1/8 0.065 +/-10 %
(.065"/1,65 mm wall)
1" 25,4 16G +.005/-.005 +1/8 0.065 +/-10 %
(.065"/1,65 mm wall)
1 ½" 39,1 16G +.008/-.008 +1/8 0.065 +/-10 %
(.065"/1,65 mm wall)
2" 50,8 16G +.008/-.008 +1/8 0.065 +/-10 %
(.065"/1,65 mm wall)
2 ½" 63,5 16G +.010/-.010 +1/8 0.065 +/-10 %
(.065"/1,65 mm wall)
3" 76,2 16G +.015/-.015 +1/8 0.065 +/-10 %
(.065“/1,65 mm wall)
4" 101,6 14G +.015/-.015 +3/16 0.083 +/-10 %
(.083"/2,11 mm wall)
6" 152,4 10,4G +.030/-.030 +3/16 0.0109 +/-10 %
(.109"/2,77 mm wall)
Bio - Pharm Range
4. Elbows 90°
Type Dimension Qualities
TE2S - 90° Elbow ½" - 6" 316L
TE2C - 90° Elbow ½" - 6" 316L
Clamp one end
TEG2S - 90° Elbow ½" - 6" 316L
Elbows 45°
Type Dimension Qualities
TE2KS - 45° Elbow ½" - 6" 316L
TE2KC - 45° Elbow ½" - 6" 316L
Clamp one end
TEG2K - 90° Elbow ½" - 6" 316L
Bio - Pharm Range
DT-7
DT-12
DT-16
DT-8
DT-13
DT-17
5. 5
Tees Symmetic
Type Dimension Qualities
TE7WWW - Tee ½" - 6" 316L
TEG7 - Tee ½" - 6" 316L
Tees - Short Outlet
Type Dimension Qualities
TE7WWCS - ½" - 6" 316L
short outlet Tee
TEG7S - ½" - 6" 316L
short outlet Tee
TE7WCSW - ½" - 6" 316L
short outlet run tee
Bio - Pharm Range
DT-9
DT-18
DT-15
DT-27
DT-25
6. Tee Reducing
Type Dimension Qualities
TE7RWWW - ¾" / ½" up to 316L
Reducing Tee 6" / 4"
TEG7R - ¾" / ½" up to 316L
Reducing Tee 6" / 4"
TE7RWWCS ¾" / ½" up to 316L
short outlet reducing Tee 6" / 4"
TEG7RS ¾" / ½" up to 316L
short outlet reducing Tee 6" / 4"
Bio - Pharm Range
DT-10
DT-19
DT-14
DT-20
7. 7
Reducers - Concentric
Type Dimension Qualities
TE31WW - ⅜" / ¼" up to 316L
concentric reducer 6" / 4"
TE31CW - ¾" / ½" up to 316L
concentric reducer 6" / 4"
TEG31CC - ¾" - ½" up to 316L
concentric reducer 6" / 4"
Reducers - Eccentric
Type Dimension Qualities
TE32WW - ⅜" / ¼" up to 316L
eccentric reducer 6" / 4"
TE32CW - ¾" / ½" up to 316L
eccentric reducer 6" / 4"
TEG32CC - ¾" / ½" up to 316L
eccentric reducer 6" / 4"
Bio - Pharm Range
DT-11
DT-26
DT-21
DT-11
DT-26
DT-21
8. Ferrules
Type Dimension Qualities
TEG14AM7 ½" - 6" 316L
Clamp Ferrule long
TEG14BM7 ½" - 6" 316L
Clamp Ferrule medium
TEG2CS ½" - 6" 316L
Clamp Ferrule short
End Caps, Caps and Gaskets
Type Dimension Qualities
TEG16A ½" - 6" 316L
Solid End Cap
TE16W ½" - 6" 316L
Cap
TEG40 ½" - 4" PTFE, VITON®
, Buna, Silicone,
EPDM and TUF-STEEL,
Envelope type - Telefon with
EPDM Filler, Tefl on with
VITON®
Filler,
Bio - Pharm Range
DT-22
DT-22
DT-22
DT-31
DT-30
9. 9
Clamps
Type Dimension Qualities
13MHHMD - Double Hinged 1 ½" - 4" 316
Heavy Duty Clamp
13MHHM - ½" - 6" 304
Heavy Duty Clamp
13MHHM - H ½" - 6" 304
Heavy Duty Clamp
13MHHS - Three Piece 1 ½" - 4" 304
Heavy Duty Clamp
13MHP - ½" - 6" 316
High Pressure Clamp
(Wing Nut With Hole)
Bio - Pharm Range
10. BioConnect®
- High Purity Tube Connection
- Optimized recess contour (patent approved)
- Highest compression power at the transitions to wetted areas prevents dirt
and germs getting into the sealing space (see ASME-BPE, Ch. SD-3.7.2 and 3.7.6)
- Defi ned expansion pockets excludes dangerous “escalator effect” between wetted
area and elastomer seat (see ASME-BPE, Ch. SD-3.7.2)
- Self-draining even after expansion of seal due to high temperature operation
(see ASME-BPE, Ch. SD-3.7.7)
- Metal-to-metal-stop avoids stress or overcompression of gaskets (O-ring)
(see ASME-BPE, Ch. SD-3.7.8)
- Nominal Pressure PN16 (DN6 - DN100, ½'' - 4'')
Bio - Pharm Range
11. 11
Connect S®
- a Unique Solution without Elastomer Gasket
- Optimal recess contour and design of the sealing metallic surface (patent approved)
- Excellent cleanability
- Tested by Frauenhofer-Institut for Grenzflächen-und Bioverfahrenstechnik
- Hermetic tightness even under repeated temperature changes
- Defined pre-stressing on the metallic sealing surface
- No gasket - no elevator effect
- Protection of the sealing contour against damage
- Axial positioning by metal-to-metal-stop
- Exact positioning by central guidance
- Material grade 1.4435/316L; other grades on request
- Wetted areas with roughness Ra<0,8µm (Ra<0,5µm on demand)
- Dimensions acc. ASME-BPE, DIN 11866, DIN 11850, ISO 1127
- Material Test Report according EN 10204-3.1 (on request AD2000 W2)
- Approval for pressure application: issued by TÜV Germany (Süddeutschland)
a) Nominal Pressure: PN16 (DN6 until DN50)
PN10 (DN65 until DN100)
PN100 (DN6 until DN40, high pressure-aseptic connection)
Bio - Pharm Range
12. NEUMO Budapest Kft. (Hungary)
NEUMO Mühendislik ve (Turkey)
EGMO Ltd. (Israel)
NEUMO Representative Offices Vietnam
NEUMO VARGUS (China)
Armaturenwerk Hötensleben GmbH (Germany)
AWH Vienna (Austria)
AWH Lyon (France)
Gebr. Rieger GmbH & Co. KG (Germany)
NEUMO GmbH & Co. KG (Germany)
Damstahl GmbH & Co. KG (Germany)
NEUMO UK Ltd. (United Kingdom)
VNE Corporation (USA)
Damstahl AG (Switzerland)
Herrli AG (Switzerland)
NEUMO-EGMO Spain SL (Spain)
NEUMO Polska Sp. z.o.o. (Poland)
NEUMO GUS (Russia)
Damstahl AB (Sweden)
Damstahl a/s (Denmark)
Damstahl a/s (Norway)
NEUMO GUS Kransodar (Russia)
NEUMO-Ehrenberg-Gruop
NEUMO UK Ltd.
Halesfield 4
Telford
Shropshire TF7 4AP
Tel.: +44 1952 583999
Fax: +44 1952 583958
e-mail: stainless@neumo.co.uk
http://www.neumo.co.uk
