This is the Highly Detailed factory service repair manual for the2000 ARCTIC CAT ZR 600, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.2000 ARCTIC CAT ZR 600 Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
General Information
Engine
Engine-Related Items
Fuel Systems
Engine Electrical Systems
Chassis Electrical Systems
Steering and Body
Drive Train System and Brake Systems
Track / Rear Suspension
Wiring Diagrams
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to have2000 ARCTIC CAT ZR 600 Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
6. Snowmobile
Identification
The Arctic Cat Snowmobile has several identification
numbers. The Vehicle Identification Number (VIN) is
stamped into the tunnel near the right-side footrest (Fig.
1). The Engine Serial Number (ESN) is stamped into
the crankcase of the engine. The Engine Model Number
is located on the engine magneto housing.
Fig. 1-1
0726-383
These numbers are required to complete warranty
claims properly. No warranty will be allowed by Arctic
Cat Inc. if the engine serial number or VIN is removed
or mutilated in any way.
Recommended
Gasoline and Oil
Recommended Gasoline
(Carbureted Models)
The recommended gasoline to use in these
snowmobiles is 87 minimum octane regular unleaded.
In many areas, oxygenates (either ethanol or MTBE) are
added to the gasoline. Oxygenated gasolines containing
up to 10% ethanol or up to 15% MTBE are acceptable
gasolines; however, whenever using oxygenated
gasolines, the carburetor main jet must be one size
larger than the main jet required for regular unleaded
gasoline. For example, if a 400 main jet is
recommended for regular unleaded gasoline, a 410
main jet must be installed if using an oxygenated
gasoline.
When using ethanol blended gasoline, it is not
necessary to add a gasoline antifreeze since ethanol will
prevent the accumulation of moisture in the fuel system.
Do not use white gas or gasolines containing
methanol. Only Arctic Cat approved gasoline
additives should be used.
Recommended Gasoline (EFI Models)
The recommended gasoline to use in these
snowmobiles is 87 minimum octane regular unleaded,
and the Fuel Designation Connector at the ECU must be
connected. In many areas, oxygenates (either ethanol or
MTBE) are added to the gasoline. Oxygenated
gasolines containing up to 10% ethanol or up to 15%
MTBE are acceptable gasolines; however, if
oxygenated gasoline is used, the Fuel Designation
Connector at the ECU must be disconnected. Do not use
gasolines containing methanol.
Fig. 1-2
734-482A
Do not use white gas or gasoline containing
methanol. Only Arctic Cat approved gasoline
additives should be used.
If oxygenated gasoline is to be used, it is
extremely important that the Fuel Designation
Connector at the ECU is disconnected. If the
connector is not disconnected when using
oxygenated gasoline, severe engine damage
may occur.
NOTE: In order for the ECU to change modes, the
engine must be OFF when connecting or
disconnecting the Fuel Designation Connector.
Recommended Oil
The recommended oil to use in the oil-injection system
is Arctic Cat 50:1 Injection Oil. This oil is specially
formulated to be used either as an injection oil or as a
pre-mix oil (for carbureted model break-in) and meets
all of the lubrication requirements of the Arctic Cat
snowmobile engine.
! CAUTION
! CAUTION
! CAUTION
1-2
7. Any oil used in place of the recommended oil
could cause serious engine damage.
Break-In Procedure
The Arctic Cat engine (when new or rebuilt) requires a
short break-in period before the engine is subjected to
heavy load conditions. Arctic Cat requires that the first
tankful of fuel be premixed at a 100:1 ratio in all
carbureted oil-injection models; however, Arctic Cat
does not recommend any premixed fuel be used during
break-in period for EFI models.
On EFI models, DO NOT use premixed fuel in the
snowmobile gas tank. Engine damage will occur.
During the break-in period, a maximum of 1/2 throttle
is recommended; however, brief full-throttle
accelerations and variations in driving speeds
contribute to good engine break-in.
On carbureted models, DO NOT exceed the one
(1) tankful limitation of a 100:1 gas/oil break-in
mixture. Continuous use of a gas/oil mixture,
unless consistently operating in extremely cold
conditions (-26°C/-15°F or colder), could cause
spark plug fouling and excessive carbon
buildup. A 100:1 gas/oil mixture must be used in
conjunction with the oil-injection system to
ensure adequate engine lubrication in extremely
cold conditions.
Genuine Parts
When replacement of parts is necessary, use only
genuine Arctic Cat parts. They are precision-made to
ensure high quality and correct fit.
High Altitude Operation
Operating a snowmobile at varying altitudes requires
changes in performance components. These changes
affect drive train components (on all models) and
carburetion components (on carbureted models).
A high altitude information decal is located beneath the
hood of the snowmobile. On carbureted models, the
information is incorporated into the Main Jet Chart
decal.
On carbureted models, carefully follow the Main
Jet Chart recommendations for proper main jet
selection for altitude, temperature, and gasoline
being used.
A number of Arctic Cat snowmobiles are initially set up
at the factory for operation between 5000-9000 feet.
Consult the appropriate specifications for this
information.
Preparation
For Storage
Prior to storing the snowmobile, it must be properly
serviced to prevent corrosion and component
deterioration. An authorized Arctic Cat Snowmobile
dealer should perform this service; however, the
owner/operator can perform this service if desired. To
prepare the snowmobile for storage, Arctic Cat
recommends the following procedure:
1. Clean the seat cushion with a damp cloth and Arctic
Cat Vinyl Protectant (p/n 0638-313).
2. Clean the snowmobile thoroughly by hosing dirt,
oil, grass, and other foreign matter from the skid
frame, tunnel, hood, and belly pan. Allow the
snowmobile to dry thoroughly. DO NOT get water
into any part of the engine.
3. Place the rear of the snowmobile up on a shielded
safety stand.
NOTE: On some models, the air-intake silencer is
a one-piece unit, and the silencer boot(s) can be
removed to access the intake bore(s). Remove the
boots; then proceed to step 7.
! CAUTION
! CAUTION
! CAUTION
! CAUTION
1
1-3
8. NOTE: On some models, the air-intake silencer
includes a cover/tool tray assembly and a
baffle/resonator, and the silencer boot cannot be
removed to access the intake bores. Proceed to
step 4.
4. Open the air-intake silencer cover; then remove the
3 Phillips-head screws securing the cover/tool tray
assembly to the silencer.
5. Close the cover; then tip the cover/tool tray
assembly forward and out of its slots and remove
the assembly.
6. Using a large flat-blade screwdriver, remove the
baffle/resonator tabs from the air-intake silencer
slots and remove the baffle/resonator to access the
intake bores.
NOTE: The baffle/resonator can be removed more
easily by removing the back tabs first.
7. Start the engine and allow to idle. With the engine
idling, spray Arctic Cat Engine Storage Preserver
(p/n 0636-177) into the intake(s) until the engine
exhaust starts to smoke heavily or until the engine
starts to drop in RPM. Turn engine off.
NOTE: On some models, install the air-intake
silencer boot(s); on some models, install the
baffle/resonator and the cover/tool tray assembly.
8. Plug the exhaust system outlet with a clean cloth.
9. With the ignition switch in the OFF position:
A. Disconnect the high tension leads from the spark
plugs; then remove the plugs, connect them to
the leads, and ground them on the cylinder
heads.
Never crank the engine over without grounding
the spark plugs. Damage to coils and/or CDI unit
may result.
B. Pour 29.5 ml (1 fl oz) of SAE #30
petroleum-based oil into each spark plug hole
and pull the recoil starter handle slowly about 10
times.
C. Install the spark plugs and connect the high
tension leads.
10. On carbureted models, drain the gas from each
carburetor float chamber.
11. Fill the gas tank to its rated capacity; then add
Arctic Cat Fuel Stabilizer (p/n 0638-165) to the gas
tank following directions on the container for the
stabilizer/gasoline ratio. Tighten the gas tank cap
securely.
12. Drain the chain-case lubricant by removing the
chain-case drain plug located on the backside of the
chain-case assembly. Remove the chain-case cover
and inspect chain, sprockets, chain tensioner, and
rollers for wear and the chain for proper tension.
Install the drain plug, chain-case cover, and seal;
then pour Arctic Cat Transmission Lube (p/n
0636-817) into the filler hole according to
appropriate specifications.
13. Remove the drive belt from the drive clutch/driven
pulley. Lay the belt on a flat surface or slide it into
a cardboard sleeve to prevent warping or distortion
during storage.
14. Clean and inspect the drive clutch and driven pulley.
15. Apply light oil to the upper steering post bushing,
ski spindles and bolts, front and rear pivot bushings
of the skid frame, and plungers of the shock
absorbers.
16. Lubricate the front and rear suspension, spindles,
and speedometer drive adapter with a
low-temperature grease.
17. Tighten all nuts, bolts, and cap screws making sure
all calibrated nuts, bolts, and cap screws are
tightened to specifications. Make sure all rivets
holding the components together are tight. Replace
all loose rivets.
18. Clean and polish the hood, console, and chassis
with Arctic Cat Hood and Windshield Cleaner/
Polish (p/n 0636-174). DO NOT USE SOLVENTS
OR SPRAY CLEANERS. THE PROPELLANT
WILL DAMAGE THE FINISH.
19. On electric start models, disconnect the battery
cables making sure to disconnect the negative cable
first; then clean the battery posts and cables.
20. If possible, store the snowmobile indoors. Raise the
track off the floor by blocking up the back end
making sure the snowmobile is secure. Loosen the
track adjusting bolts to reduce track tension. Cover
the snowmobile with a machine cover or a heavy
tarpaulin to protect it from dirt and dust.
21. If the snowmobile must be stored outdoors, position
the snowmobile out of direct sunlight; then block
the entire snowmobile off the ground making sure
the snowmobile is secure. Loosen the track
adjusting bolts to reduce track tension. Cover with
a machine cover or a heavy tarpaulin to protect it
from dirt, dust, and rain.
Avoid storing in direct sunlight and using a
plastic cover as moisture may collect on the
snowmobile causing corrosion.
! CAUTION
! CAUTION
1-4
9. Preparation After
Storage
Taking the snowmobile out of storage and correctly
preparing it for another season will assure many miles
and hours of trouble-free snowmobiling. Arctic Cat
recommends the following procedure:
On carbureted models if the gas in each
carburetor float chamber was not drained prior
to storage, the carburetor(s) must be cleaned
before starting the engine.
1. Clean the snowmobile thoroughly. Polish the
exterior of the snowmobile.
2. Clean the engine. Remove the cloth from the
exhaust system. Check exhaust system and
air-intake silencer for obstructions.
3. Inspect all control wires and cables for signs of
wear or fraying. Replace if necessary. Use cable ties
or tape to route wires and cables away from hot or
rotating parts.
4. Inspect the drive belt for cracks and tears. Check
belt specifications. Replace if damaged or worn.
Install the drive belt.
NOTE: If the old belt is worn but in reasonable
condition, retain it with the snowmobile as a spare
in case of emergency.
5. On carbureted models, inspect the in-line fuel filter
and replace if necessary.
6. Inspect all fuel hoses and oil hoses for deterioration
or cracks; replace if necessary. Make sure all
connections are tight; then fill the oil-injection
reservoir with 50:1 injection oil.
NOTE: On carbureted models after prolonged
storage, Arctic Cat recommends one tankful of
100:1 gas/oil mixture be used in conjunction with
the oil-injection system to ensure proper
lubrication.
7. Inspect the entire brake system, all controls,
headlight, taillight, brakelight, ski wear bars, and
headlight aim; adjust or replace as necessary.
8. Inspect the spark plugs. Replace, gap, or clean as
necessary.
9. Adjust the track to the proper tension and
alignment. Lock the jam nuts.
10. Adjust the carburetor(s) and choke cable on
carbureted models and throttle cable on all models.
On VM-style carburetors, be sure to tighten the
swivel adapter jam nuts securely. If a jam nut
isn’t tightened, the adjuster can rotate out of the
carburetor cap causing the piston valve not to
return to the full-closed position.
11. Tighten all nuts, bolts, and cap screws making sure
all calibrated nuts, bolts, and cap screws are
tightened to specifications.
12. Lubricate the rear suspension, spindles, and
speedometer drive adapter with a low-temperature
grease.
13. On liquid cooled models, check the coolant level
and all coolant hoses and connections for
deterioration or cracks. Add properly mixed coolant
as necessary.
14. On fan cooled models, clean the engine cooling fins
and vents.
15. On EFI models, place the rear of the snowmobile on
a shielded safety stand; then start the engine. Allow
the engine to idle; then using a long stiff wire with
a hooked end, raise the oil-injection pump control
arm to the wide-open position until the engine starts
to smoke heavily. Release the control arm and turn
off the engine.
16. On electric start models, charge the battery; then
connect the battery cables making sure to connect
the positive cable first. Test the electric start system.
After Break-In Checkup
(100 Miles)
The 100 mile checkup offered by some dealerships
reduces problems and warranty costs. A program of this
kind should be offered by all dealerships. Many
dealerships have added the price of the checkup into the
selling price of the snowmobile, and others offer it as a
bonus to the customers who purchase snowmobiles
from their dealership.
There are three areas that require adjustment after the
break-in period in order to obtain peak performance.
These areas are the following.
A. Carburetor jetting
B. Drive belt deflection
C. Track tension and alignment
! CAUTION
! CAUTION
1
1-5
10. Carburetor Jetting - Altitude, temperature, and the use
of oxygenated gasoline affect the carburetion needed
for optimum engine performance. The carburetor main
jets must be changed in conjunction with changes in
operating altitude, oxygenated gasoline usage, and
temperature.
Drive Belt Deflection - Drive belt deflection is very
important to the snowmobile. Even if it is checked and
is correct when the snowmobile is set up, it does change
(more so during the break-in period). This is because
the rubber engine mounts and the rubber snubber on the
torque link will all take a “set” during the first 100
miles, which allows the distance between the drive
clutch and driven pulley to shorten. When this happens,
the snowmobile will appear to have a too long drive belt.
To add to this, the drive belt itself wears and stretches
somewhat. This all leads to a low-end performance
problem and, if not corrected, causes premature drive
belt wear.
After the break-in period, drive belt deflection should
be checked according to the instructions given in this
manual. To correct for too much deflection, washer(s)
from between the driven pulley sheaves can be removed
to “tighten the drive belt” and allow the belt to return to
the proper ratio for drive clutch engagement.
Drive Belt Break-In - It is critical for maximum drive
belt life to allow the belt to break in before subjecting it
to hard use such as wide-open-throttle operation or hill
climbing.
The first 20 miles on the drive belt should be at 1/2
throttle or lower. This will allow the belt to cure totally
before it is subjected to hard use.
If this procedure isn’t followed, it is possible to destroy
a new drive belt in less than 50 miles. This should be
explained to customers at the time of drive belt sales.
To increase the life of a drive belt, it is very important
that the belt be warmed up before subjecting it to any
type of use. In cold temperature (0° or below), the
engine should be allowed to idle for a period of 8 to 10
minutes. This will allow heat from the engine
compartment to soften the drive belt. Not only will this
procedure increase belt life but will also help prevent
engine damage from cold seizure.
! WARNING
When following the above procedure, the
operator must not leave the snowmobile
unattended during the warm-up period.
Each operator should be instructed to drive the
snowmobile for several minutes at a low throttle setting
to warm the belt up before using wide-open-throttle.
This practice should be followed on all models for
maximum belt life.
Track Tension and Alignment - There is a certain
amount of stretch on all tracks during the first 500
miles. The track must be adjusted after the first 50 to
100 miles to the specifications given in the Setup and
Predelivery Manual and periodically thereafter. If these
adjustments aren’t performed, the track may “derail”
which leads to track and slide rail damage.
Along with these three major areas, there are also other
areas that should be checked and adjusted during the
“After Break-In Checkup.” A checklist to assist you
with this service follows. Not only will the customer be
happier, but it also gets the customer back into your
dealership, which in many cases will mean additional
sales in accessories, belts, oil, etc.
After Break-In
Checkup Checklist
Below is a recommended list of items to check after the
break-in period. By performing this inspection,
warranty cost can be reduced and customer satisfaction
can be increased.
The recommended mileage for this inspection is
between 100 and 300 miles. Please encourage the
customers to have this important checkup done.
❏ Jet carburetor(s) according to average
temperature, type of gasoline being used, and
altitude
❏ Adjust drive belt deflection
❏ Adjust track tension and alignment
❏ Adjust throttle cable tension
❏ Check oil-injection pump adjustment
❏ Check engine idle
❏ Check coolant level
❏ Check chain case lubricant level
❏ Check lights (high-low beam, brakelight)
❏ Check safety switch operation
❏ Check driveshaft area for any rubbing
components
❏ Check steering hardware for tightness
❏ Check skid frame and A-arm mounting
hardware for tightness
❏ Check brake lever travel and adjustment
❏ Grease all lubrication points
1-6
14. Servicing Symbols
Listed in the table below are symbols indicating special
instructions and other important information necessary
for proper servicing. Please note the definition for each
symbol. These symbols are used throughout this
two-volume set.
SYMBOL DESCRIPTION
Torque control required
243 - apply blue Loctite #243 (p/n 1048-028)
270 - apply green Loctite #270 (p/n 1048-030)
Lubricate with Arctic Cat 50:1 Injection Oil (p/n 0636-286)
Lubricate with Arctic Cat Low Temp Grease (p/n 0636-593)
3B - Three Bond Sealant (p/n 0636-070)
HT - High-Temp Sealant (p/n 0636-069)
AS - Anti-Seize Thread Compound (p/n 0678-146)
1-10
16. Engine
This engine servicing section has been organized into
sub-sections which show a progression for the complete
servicing of the Arctic Cat engine. For consistency
purposes, this section shows a complete and thorough
progression; however, for efficiency it may be
preferable to remove the engine as a complete assembly,
to remove and disassemble only those components
which need to be addressed, and to service only those
components. The technician should use discretion and
sound judgment.
NOTE: Some photographs used in this section
are used for clarity purposes only and are not
designed to depict actual conditions.
Removing Engine
Table of Contents
60 cc Model . . . . . . . . . . . . . . . . . . . . 2-2
Twin F/C Models . . . . . . . . . . . . . . . . . 2-3
440 LC/500/580/600 Twin/700 cc Models . . . . 2-5
550 cc Models . . . . . . . . . . . . . . . . . . 2-7
Triple Models . . . . . . . . . . . . . . . . . . . 2-9
Removing Engine
(60 cc Model)
1. Remove the cap screw securing the hood cable to
the engine.
2. Remove the two sheet metal screws securing the
chain guard to the console and tunnel.
Fig. 2-1
A940
3. Disconnect the connecting link in the drive chain;
then remove the drive chain.
4. Remove the cap screw and rubber mount securing
the brake band to the brake assembly bracket.
Account for a spacer and a washer.
Fig. 2-2
A951
5. Remove the brake band assembly.
6. Loosen the throttle cable set screw; then loosen the
throttle cable jam nut and remove the throttle cable.
Fig. 2-3
A954
Fig. 2-4
A953
7. Disconnect the engine wiring harness from the
main wiring harness.
2-2
17. Fig. 2-5
A957
8. From beneath the front end, remove the four cap
screws securing the engine to the front end.
Account for the washers and lock washers.
Fig. 2-6
A958
9. Remove the engine assembly.
Removing Engine
(Twin F/C Models)
NOTE: If equipped with electric start, disconnect
the battery.
1. Turn the gas tank shut-off valve to the CLOSED
position.
2. Open the belt guard.
3. Remove the drive belt; then remove the plug from
the belly pan.
NOTE: Before installing the clutch puller, apply oil
to the threads of the puller and a small amount of
grease to the tip of the puller.
4. Remove the bolt and lock washers securing the
drive clutch to the crankshaft; then using the Drive
Clutch Puller (p/n 0644-207) and an impact wrench
or a breaker bar and Drive Clutch Spanner Wrench
(p/n 0644-136), tighten the puller. If the drive clutch
will not release, sharply strike the head of the puller
with a hammer. Repeat this procedure until the
clutch releases.
Fig. 2-7
AF472D
Fig. 2-8
AF476D
5. Remove the clutch from the engine compartment.
6. Remove the cap screw and washer securing the
driven pulley; then slide the pulley off the driven
shaft. Account for and note the position of any
alignment washers.
NOTE: If the driven pulley will not slide off the
driven shaft, use the Driven Pulley Puller (p/n
0744-023) for removal.
2
2-3
18. Fig. 2-9
SC013D
7. Remove the torque bumper. Account for any engine
mount shims.
Fig. 2-10
AF473D
8. Remove the springs securing the expansion
chamber to the exhaust manifold and resonator;
then remove expansion chamber.
Fig. 2-11
AC067
9. Remove the cap screws and lock washers securing
the recoil starter; then remove the starter. Leave it
in the engine compartment.
Fig. 2-12
AB082
10. Disconnect the four-prong main wiring harness
connector and the CDI unit wiring harness.
11. Disconnect the impulse hose from the crankcase.
12. Disconnect the spark plug caps.
13. Loosen the carburetor flange clamp(s). Remove the
carburetor(s) from the intake flange(s) and
carburetor boot(s). Place the carburetor(s) to the
side in an upright position.
NOTE: If equipped with electric start, remove the
lock nuts and washers securing the starter motor to
the engine mounting bracket and remove the starter
motor.
14. Disconnect the oil-injection cable from the
oil-injection pump. Account for the E-clip and
washer; then disconnect the oil supply hose from
the pump and plug the hose to prevent leakage.
Fig. 2-13
AB081
NOTE: If equipped with electric start, remove the
two lock nuts and washers securing the starter
motor bracket; then remove the three remaining cap
screws, washers, and lock washers securing the
starter motor bracket and ground cable. Remove
the starter motor bracket.
15. On the Bearcat models, remove the four cap screws
securing the engine plate to the front end. Account
for four washers, female mounts, and cup washers.
2-4
19. Fig. 2-14
AL201D
16. On the Bearcat models, lift the engine w/plate out
of the engine compartment.
17. On the Bearcat models, remove the cap screws
securing the plate assembly to the engine; then
separate the engine and plate.
Fig. 2-15
AB007
18. On the Panther/Z models, remove the cap screws
securing the engine to the front end. Account for
washers, cap screws, and lock nuts.
19. On the Panther/Z models, lift the engine out of the
engine compartment.
20. On the Panther/Z models, remove the cap screws,
washers, and lock washers securing the engine
mounting brackets to the engine; then remove the
brackets.
Removing Engine (440 LC/
500/580/600 Twin/700 cc Models)
NOTE: If applicable, disconnect the battery
cables.
1. Turn the gas tank shut-off valve to the CLOSED
position.
2. Remove all springs securing the expansion
chamber(s) and remove the expansion chamber(s)
from the engine compartment.
3. Open the belt guard; then remove the drive belt.
4. Remove the plug from the belly pan. Using a ½-in.
12-point socket, remove the cap screw and lock
washer securing the drive clutch to the crankshaft;
then using Clutch Puller (p/n 0644-207) and an
impact wrench or a breaker bar and Spanner
Wrench (p/n 0644-136), tighten the puller. If the
drive clutch will not release, sharply strike the head
of the puller. Repeat this step until the clutch
releases. Remove the drive clutch. If applicable,
account for the two sleeves.
Fig. 2-16
AN380D
5. Remove the cap screw and washer securing the
driven pulley; then slide the driven pulley off the
driven shaft. Account for a key, stub shaft, and
alignment washers.
Fig. 2-17
AF120D
NOTE: If the driven pulley is tight on the driven
shaft, pull the driven pulley off using the Driven
Pulley Puller (p/n 0744-023).
6. If applicable, remove the machine screw and
washer securing the mounting plate (for the ignition
coil and fuel pump) to the air-intake silencer.
2
2-5
20. Fig. 2-18
AN613D
NOTE: On the 700 cc models, lift the air-intake
silencer; then move the silencer forward and out of
the engine compartment.
7. Remove the screws securing the air-intake silencer;
then move the silencer forward and out of the
engine compartment.
8. Loosen the flange clamps securing the throttle
body/carburetor to the flange; then remove the
throttle body/carburetor. Place them to one side in
an upright position.
9. On carbureted models, disconnect the impulse hose
from the crankcase.
Fig. 2-19
AN385D
10. Loosen the engine torque bumper and remove the
left rear engine nut and washer.
Fig. 2-20
AN610D
11. Secure the hood with a tie-down strap; then remove
the hood cable.
12. Remove the exhaust manifold from the engine.
Account for nuts, washers, and gaskets.
13. Disconnect all electrical wires from the engine.
14. Remove the E-clip and washer securing the oil-
injection cable; then disconnect the oil-injection
cable from the oil-injection pump. Disconnect the
oil-supply hose from the pump and plug the hose to
prevent oil drainage.
15. Remove the recoil starter from the engine. Leave it
in the engine compartment.
NOTE: If applicable, disconnect the solenoid-to-
starter motor cable from the starter motor.
16. Loosen the cap screws/lock nuts securing the
engine mounting brackets to the front end.
17. Lift the engine up and attach a long piece of fuel
hose to the engine coolant drain (located on the
exhaust side of the engine). Route the hose outside
the engine compartment and into a container. Open
the drain and remove the filler cap. Once the
coolant stops flowing, remove the hose and tighten
the drain valve.
Fig. 2-21
AP058
2-6
21. 18. Raise the engine up slightly; then loosen the clamp
securing the supply hose to the water pump housing
and remove the hose from the water pump. Loosen
the clamp securing the hose to the thermostat cap;
then remove the hose from the cap.
Fig. 2-22
AN143
NOTE: Inspect the engine to ensure all wires,
hoses, and cables have been removed.
19. Lift the engine with mounting brackets out of the
engine compartment.
20. Remove the cap screws securing the engine
mounting brackets to the crankcase; then remove
the brackets.
Removing Engine
(550 cc Models)
1. Disconnect the battery cables making sure to
disconnect the negative cable first.
2. Turn the gas tank shut-off valve to the CLOSED
position.
3. Remove the cable tie and positive battery cable
from the starter motor.
4. On the Wide Track, remove the two lock nuts
securing the starter motor to the engine mounting
bracket; then place the starter motor and end cap off
to the side.
5. Remove the springs securing the expansion
chamber to the exhaust manifold, front end, and
resonator. Remove the expansion chamber and
grafoil gasket.
6. Attach a long piece of fuel hose to the engine
coolant drain (located on the exhaust side of the
engine). Route the hose outside the engine
compartment and into a container. Open the drain
and remove the filler cap. Once the coolant stops
flowing, remove the hose and tighten the drain
valve.
Fig. 2-23
AP058
7. Open the belt guard: then remove the drive belt.
NOTE: On the Wide Track, remove the machine
screws securing the side panel to the belly pan;
then remove the side panel. On the Panther 550 and
ZL 550, remove the rubber plug from the belly pan.
Fig. 2-24
AM115D
8. Using a ½-in. twelve-point socket, remove the bolt
and lock washer securing the drive clutch to the
crankshaft. Using the Clutch Puller (p/n 0644-207)
and an impact wrench or a breaker bar and the
Flywheel Pulley/Spanner Wrench (p/n 0144-310),
tighten the puller. If the drive clutch will not release,
sharply strike the head of the puller. Repeat this step
until the clutch releases. Remove the drive clutch.
If applicable, account for the two sleeves.
NOTE: On the Wide Track, remove the lock nut
securing the belly pan and bumper to the bumper
support tube; then remove the rear plug from the
belly pan.
2
2-7
22. Fig. 2-25
AF459D
9. Remove the cap screw and washer securing the
driven pulley; then slide the driven pulley off the
driven shaft. Account for a key and alignment
washers.
Fig. 2-26
AF120D
NOTE: If the driven pulley is tight on the driven
shaft, pull the driven pulley off using the Driven
Pulley Puller (p/n 0744-023).
10. Loosen the flange clamp securing each carburetor
to its flange; then remove the carburetors. Position
the carburetors to one side in an upright position.
Fig. 2-27
AJ172
11. Disconnect the impulse hose from the crankcase.
12. Remove the cable tie securing the engine and CDI
wiring harnesses to the engine; then disconnect the
main wiring harness from the engine and CDI
wiring harnesses.
13. Remove the spark plug caps and the cable tie
securing the temperature-gauge sender wire; then
disconnect the sender wire.
14. On the Wide Track, remove the ground wire from
the magneto housing.
15. Remove the E-clip and washer securing the
oil-injection cable; then disconnect the oil-injection
cable from the pump. Disconnect the oil-supply
hose from the pump and plug the hose to prevent oil
drainage.
Fig. 2-28
AN009
16. Loosen the clamp securing the supply hose to the water
pump housing; then remove the hose from the water
pump. Loosen the clamp securing the hose to the
thermostat cap; then remove the hose from the cap.
17. Remove the four cap screws and lock washers
securing the recoil starter; then remove the starter
from the engine. Leave it in the engine
compartment.
NOTE: On the Panther 550, account for the
ground wire.
18. Support the hood; then remove the hood cable from
the exhaust manifold.
19. Remove the mounting hardware securing the
engine to the front end.
NOTE: On the Wide Track, account for shims and
note their position on the left rear engine mount for
assembly purposes.
2-8
23. Fig. 2-29
AR321
Fig. 2-30
AN013
20. Lift the engine with mounting brackets out of the
engine compartment.
Do not use the starter motor shaft to lift the
engine. Damage may occur.
21. Remove the engine mounting brackets.
Removing Engine
(Triple Models)
1. Turn the gas tank shut-off valve to the CLOSED
position.
Fig. 2-31
AL658D
2. Secure the hood with a hold-down strap; then
remove the hood cable.
3. Remove the springs securing the expansion
chambers to the header pipes, the front end, and the
resonator. Remove the expansion chambers and
three grafoil gaskets.
NOTE: Number the expansion chambers before
removing to aid in assembly.
4. Remove the cap screws securing the resonator.
Account for and note the location of the engine
ground cable with star washer, washers, bushings,
spacers, and retaining nuts.
5. Attach a long piece of fuel hose to the engine
coolant drain. Route the hose outside the engine
compartment and into a container. Open the drain
valve; then remove the coolant filler cap to vent the
system. Once the coolant stops flowing, remove the
hose and tighten the drain valve.
Fig. 2-32
AQ123
6. Open the belt guard; then remove the drive belt.
! CAUTION
2
2-9
24. 7. Remove the plug from the belly pan; then using a
1/2 in. twelve-point socket, remove the bolt and
lock washer securing the drive clutch to the
crankshaft. Using the Drive Clutch Puller (p/n
0644-207) and an impact wrench or a breaker bar
and Spanner Wrench (p/n 0644-136), tighten the
puller. If the drive clutch will not release, sharply
strike the head of the puller. Repeat this step until
the clutch releases. Remove the drive clutch. If
applicable, account for the two sleeves.
Fig. 2-33
AF472D
8. Remove the cap screw securing the driven pulley;
then slide the driven pulley off the driven shaft.
Account for a stub shaft, the location of all washers,
and a key.
Fig. 2-34
SC013D
NOTE: If the driven pulley is tight on the shaft, pull
the driven pulley off using the Driven Pulley Puller
(p/n 0744-023).
9. Label the carburetors. Loosen the flange clamp
securing each carburetor to its flange; then remove
the carburetors from the intake flanges. Position the
carburetors to one side in an upright position.
Fig. 2-35
AN614D
10. Disconnect the impulse hose from the crankcase.
11. Loosen the engine torque bumper; then remove the
left-side rear engine nut and washer.
Fig. 2-36
AN610D
12. Disconnect the engine and timing sensor wiring
harnesses from the main wiring harness. Remove
the spark-plug caps from the spark plugs. Remove
the cap screw securing the two ground wires to the
magneto housing cover.
13. Remove the E-clip and washer securing the
oil-injection cable; then disconnect the oil-injection
cable from the oil-injection pump. Disconnect the
oil-supply hose and the oil-output hose from the
pump and plug the hoses to prevent oil drainage.
Fig. 2-37
AN392D
2-10
25. 14. Loosen the clamp securing the coolant supply hose
to the water pump housing; then remove the hose
from the water pump. Loosen the clamp securing
the hose to the thermostat cap; then remove the hose
from the cap.
15. Disconnect the temperature-gauge sender wire.
Fig. 2-38
AJ663
16. Remove the cap screws securing the engine
mounting brackets to the front end. Account for
mounting hardware.
17. Lift the MAG-side of the engine. Remove the four
cap screws and lock washers securing the recoil
starter; then remove the starter from the engine.
Leave it in the engine compartment.
Fig. 2-39
AN012
18. Lift the engine with engine mounting brackets out
of the engine compartment.
19. Remove the mounting brackets from the crankcase.
Disassembling Engine
Table of Contents
60 cc Model . . . . . . . . . . . . . . . . . . . 2-11
F/C Models . . . . . . . . . . . . . . . . . . . 2-16
440 LC/550 cc Models . . . . . . . . . . . . . 2-19
500/580/600 cc Twin Models . . . . . . . . . . 2-22
700 cc Models . . . . . . . . . . . . . . . . . 2-27
600 cc Triple Models . . . . . . . . . . . . . . 2-34
800/1000 cc Models . . . . . . . . . . . . . . 2-39
Disassembling Engine
(60 cc Model)
FUEL TANK/CLUTCH
1. Remove the fuel supply hose from the carburetor
body.
Fig. 2-40
A955
2. Loosen the machine screw securing the fuel tank
bracket to the recoil starter housing; then remove
the two machine screws securing the fuel tank
bracket to the cylinder head and remove the fuel
tank assembly.
2
2-11
26. Fig. 2-41
A956
3. Loosen the set screw and remove the cap screw and
washer securing the clutch to the engine primary
shaft.
Fig. 2-42
A947
Fig. 2-43
A946
4. Using a wheel puller, remove the clutch assembly
from the primary shaft.
5. Remove the four cap screws securing the engine
plate to the crankcase.
Fig. 2-44
A900
FAN/CYLINDER HEAD
6. Remove the nuts and lock washers securing the
carburetor. Slide the carburetor off intake studs;
then disconnect the carburetor rod and rod spring.
Fig. 2-45
A779
7. Slide the gasket, insulator, and gasket off intake
studs.
8. Remove the nuts and lock washers securing the
muffler. Slide the muffler off the exhaust studs; then
remove the exhaust gasket.
Fig. 2-46
A778
9. Remove the recoil starter.
2-12
27. 10. Remove the screws securing the fan cover; then
remove the cover.
Fig. 2-47
A775
11. Remove the cylinder head cowling.
Fig. 2-48
A774
12. Using a flywheel holder (or a suitable substitute),
remove the flywheel nut. Account for a lock washer
and a washer.
Fig. 2-49
A762
13. Remove the recoil starter pulley and spacer.
Fig. 2-50
A766
14. Using a flywheel puller, remove the flywheel.
Account for the key.
Fig. 2-51
A761
15. Scribe a line on the stator plate and the crankcase
for assembly purposes.
Fig. 2-52
A765
16. Remove the three screws securing the stator plate to
crankcase.
2
2-13
28. Fig. 2-53
A769
17. Disconnect the magneto lead from the ignition coil
lead. Remove the screws securing the ignition coil;
then remove the coil.
Fig. 2-54
A756
18. Remove the cylinder head nuts and washers; then
lift the head off the cylinder studs.
Fig. 2-55
A939
19. Slide the head gasket off the cylinder studs.
Fig. 2-56
A772
20. Slide the cylinder straight upward until free of the
piston. Remove the base gasket.
Fig. 2-57
A771
21. Remove the piston pin circlips; then using the
Piston Pin Puller (p/n 0644-328), remove the piston
pin.
Fig. 2-58
A776
GEAR CASE/CRANKCASE
22. Using an impact screwdriver, remove the screws
securing the gear case cover. Lift the cover off the
crankcase.
2-14
29. Fig. 2-59
A755
23. Remove the cover gasket.
24. Remove the primary driven shaft and gear from the
gear case.
Fig. 2-60
A752
25. Remove the shifter from the end of the engine
crankshaft.
Fig. 2-61
A758
26. Remove the nut securing the primary drive gear and
centrifugal to the crankshaft.
Fig. 2-62
A748
27. In order, remove the centrifugal, primary drive gear,
and key from the crankshaft.
Fig. 2-63
A747
28. Using an impact screwdriver, remove the five
screws securing the crankcase halves.
Fig. 2-64
A745
29. Carefully separate the crankcase halves.
DO NOT use a chisel, screwdriver, or any other
instrument to pry crankcase halves apart. Any
damage to the crankcase sealing area will cause
an air leak resulting in severe engine damage.
! CAUTION
2
2-15
30. Fig. 2-65
A742
30. Remove the crankshaft from the crankcase.
Disassembling Engine
(F/C Models)
1. Remove the four nuts and lock washers securing the
exhaust manifold; then remove the exhaust
manifold. Account for two gaskets.
2. Noting the location of the longer cap screws for
assembly purposes, remove the 14 cap screws, lock
washers, and washers securing the top and
exhaust-side cooling shrouds.
3. Lift the top cooling shroud off the engine and slide
the exhaust-side cooling shroud off the
exhaust-manifold studs. Account for two
exhaust-manifold shroud gaskets.
Fig. 2-66
AB014
4. Disconnect the two oil-injection hoses from their
fittings on the intake manifold (single carburetor) or
on the adapter plates (twin carburetor).
5. A. On the single carburetor model, remove the four
nuts securing the intake manifold; then remove the
manifold with flange from the engine. Account for
two insulators. Discard the four gaskets.
B. On the twin carburetor model, remove the four
nuts, lock washers, and washers securing the
intake flanges; then remove the flanges from the
engine. Remove the six screws securing the
adapter plates; then remove the adapter plates.
Discard the two gaskets.
6. Remove the intake-manifold cooling shroud from
the engine. Discard the two gaskets.
7. Using Flywheel Spanner Wrench (p/n 0144-007) to
secure the crankshaft, remove the three cap screws
and lock washers securing the starter pulley to the
flywheel. Remove the starter pulley; then carefully
pry the fan belt drive pulley from its seated position
on the flywheel and remove.
Fig. 2-67
AB020
8. Temporarily install the starter pulley on the
flywheel with three cap screws. Using the flywheel
spanner wrench to secure the crankshaft, loosen and
remove the flywheel nut and washers.
Fig. 2-68
AB021
NOTE: If an impact wrench is being used, use of a
flywheel spanner wrench will not be necessary.
9. Remove the cap screws securing the starter pulley
to the flywheel and remove the pulley.
2-16
31. 10. Remove the flange nuts securing the fan case to the
crankcase; then remove the fan case.
NOTE: For further servicing of the axial fan
components, see section 3.
Fig. 2-69
AB015
11. Install a protective cap onto the end of the
crankshaft.
NOTE: A suitable protective cap can be made by
welding a 3 mm (1/8 in.) plate on one side of a spare
flywheel nut.
Fig. 2-70
AB022
To prevent damage to the crankshaft, thread a
protective cap onto the crankshaft. The puller
must bottom on the cap and not on the
crankshaft. Also, do not thread puller bolts more
than 12.7 mm (1/2 in.) into the flywheel. Damage
to the coils may result.
12. Using the Flywheel Puller/Spanner Wrench (p/n
0144-310) or suitable equivalent, remove the
flywheel from the crankshaft by tightening the
puller bolt, striking the head of the puller bolt with
a hammer, and tightening again. Repeat procedure
until the flywheel is free. Account for the key in the
end of the crankshaft.
Fig. 2-71
AB098
NOTE: To ensure the cleanliness of the flywheel
magnets, place the flywheel (with the magnets
facing upward) on a clean bench.
13. Scribe a reference line on the stator plate and
crankcase to aid in assembly; then remove the two
Allen-head cap screws, lock washers, and washers
securing the stator plate.
NOTE:The two stator plate Allen-head cap screws
had Loctite applied to the threads during assembly.
Before removing them, apply a sharp blow to the
head of each screw to break the Loctite loose. If this
isn’t done, the screws can be very difficult to
remove.
Fig. 2-72
AB026
14. Remove the stator plate from the engine.
15. Remove the screws, lock washers, and washers
securing the oil-injection pump to the crankcase;
then remove the pump, retainer, shim, and gear.
Account for two gaskets.
! CAUTION
2
2-17
32. Fig. 2-73
AB018
16. Remove the spark plugs.
17. Remove the eight nuts, lock washers, and washers
securing the cylinder heads to the cylinders. Note
the position of the different-sized nuts. Remove the
heads and account for two gaskets.
Fig. 2-74
B563
18. Using a rubber hammer, gently tap the cylinders
and remove from the crankcase by lifting them
straight up off their studs. Discard the two gaskets.
When removing a cylinder, make sure to support
the pistons so they will not be damaged.
19. Using a felt-tipped marker, mark an M on the
MAG-side head, cylinder, and piston and a P on the
PTO-side head, cylinder, and piston.
NOTE: For proper assembly, keep all MAG-side
components and all PTO-side components
separated. Assemble them on their proper sides.
20. Remove the PTO-side piston-pin circlip from the
PTO-side piston; remove the MAG-side piston-pin
circlip from the MAG-side piston.
Fig. 2-75
A829
21. Using the Piston-Pin Puller (p/n 0644-328), remove
the piston pins from both pistons.
Fig. 2-76
A830
DO NOT use any type of punch to drive the
piston pin free of the piston; damage may result.
Use a piston-pin puller only.
22. Lift the pistons clear of the connecting rods and
remove the small end connecting-rod bearings; then
remove the piston rings. Keep each piston with its
rings, piston pin, and bearing together as a set.
NOTE: Place rubber bands over the connecting
rods and around the cylinder studs. This will keep
the connecting rods from damaging the crankcase.
! CAUTION
! CAUTION
2-18
33. Fig. 2-77
B160
23. Remove the cap screws securing the crankcase
halves. Note the position of the different-sized cap
screws.
Fig. 2-78
A831
24. Separate the crankcase halves by installing two
crankcase cap screws in diagonal corners leaving
the heads approximately 6 mm (1/4 in.) out. Using
a plastic hammer, tap on each cap screw head until
the halves separate. Remove the cap screws.
DO NOT drive any tool between the crankcase
halves to separate the crankcase. Damage to the
sealing surfaces will result.
25. Remove the rubber bands holding the connecting
rods; then separate the crankcase halves. Account
for the two dowel pins. Lift the crankshaft free from
the crankcase half and slide the two crankshaft seals
off the crankshaft. Account for the C-ring and five
bearing dowel pins.
Disassembling Engine
(440 LC/550 cc Models)
1. Using the spanner wrench to secure the flywheel,
remove the flywheel nut, lock washer, and flat
washer; then remove the three starter pulley cap
screws and remove the pulley.
Fig. 2-79
AN015
2. Install the Crankshaft Protector Cap (p/n 0644-234)
onto the end of the crankshaft.
NOTE: A suitable substitute protective cap can be
made by welding a 3 mm (1/8 in.) plate on one side
of a spare flywheel nut.
3. Using the Flywheel Puller/Spanner Wrench (p/n
0144-310) or suitable substitute, remove the
flywheel from the crankshaft by tightening the
puller bolt, striking the head of the puller bolt with
a hammer, and tightening again. Repeat this
procedure until the flywheel is free. Account for the
key.
To prevent damage to the crankshaft, the puller
must bottom on the cap and not on the
crankshaft. Also, do not thread puller bolts more
than 12.7 mm (1/2 in.) into the flywheel. Damage
to the coils may result.
! CAUTION ! CAUTION
2
2-19
34. Fig. 2-80
AN020
NOTE: To ensure the cleanliness of the flywheel
magnets, place the flywheel (with the magnets
facing upward) on a clean bench.
4. Scribe a line on the stator plate and magneto case to
aid in assembly; then remove thetwo Allen-headcap
screws, lock washers, and washers securing the
stator plate. Remove the stator plate from the engine.
Fig. 2-81
AN022
NOTE:The stator plate screws had Loctite applied
to the threads during assembly. Using an impact
driver, apply a sharp blow to the head of each screw
to break the Loctite loose before removal.
5. On the 440 cc, remove the cap screws and washers
securing the CDI unit and the external coil; then
remove from the engine.
Fig. 2-82
AN024
6. Remove the four nuts and lock washers securing the
exhaust manifold; then remove the manifold and
account for the two exhaust gaskets.
7. Remove the three cap screws securing the
thermostat cap; then remove the cap, gasket, and
thermostat.
NOTE: The thermostat is of the lock-open type. If
the thermostat is ever allowed to fully open, it will
remain open and replacement will be necessary.
8. Remove the four cap screws securing the
thermostat manifold to the cylinder heads. Remove
the manifold and discard the gaskets.
9. Remove the spark plugs.
10. Remove the six cap screws and O-rings securing
each head; then separate from the cylinder. Account
for two large O-rings beneath each head.
11. Remove the oil-injection hose from each cylinder
and the crankcase nozzle.
Fig. 2-83
AN032
12. Remove the eight nuts, lock washers, and washers
securing the cylinders to the crankcase; then using
a rubber hammer, gently tap the cylinders and
remove from the crankcase by lifting them straight
up off their studs. Account for two gaskets.
2-20
35. When removing a cylinder, be sure to support
the piston to prevent damage to the crankcase
and piston.
NOTE: The metal cylinder base gaskets may be
reused. When reusing gaskets, they must be
cleaned and sprayed with Copper Coat Gasket
Sealant (p/n 0636-092) on each side.
Fig. 2-84
AN033
13. Remove the PTO-side piston-pin circlip from the
PTO-side piston; then remove the MAG-side
piston-pin circlip from the MAG-side piston.
14. Using the Piston Pin Puller (p/n 0644-328), remove
the piston pins from both pistons.
NOTE: For proper assembly, keep all MAG-side
components and all PTO-side components
separated. Assemble them on their proper sides.
Fig. 2-85
AN036
DO NOT use any type of punch to drive the
piston pin free of the piston; damage may result.
Use a piston-pin puller only.
15. Lift the pistons clear of the connecting rods and
remove the small-end connecting-rod bearings;
then remove the piston rings. Keep each piston with
its rings; keep each piston pin and bearing together
as a set.
NOTE: Place rubber bands over the connecting
rods and around the cylinder studs.This will prevent
the connecting rods from damaging the crankcase.
16. Remove the two screws, lock washers, and washers
securing the oil-injection pump to the crankcase.
Remove the pump, retainer, and O-ring.
17. Remove the water pump cover. Account for the
O-ring gasket.
18. Remove the cap screw securing the water pump
impeller; then slide the impeller free of the shaft.
19. Using an impact driver, remove the screws securing
the PTO-end plate to the crankcase; then remove
the plate.
20. Position the crankcase (with its bottom side up) on
two blocks of wood. Remove the fourteen cap
screws securing the crankcase halves. Note the
position of the different-sized cap screws.
21. Separate the crankcase halves by installing two
crankcase cap screws in opposite corners leaving
the heads approximately 6 mm (1/4 in.) out. Using
a plastic-tipped hammer, tap on each cap screw
head until the case halves separate. Remove the cap
screws.
DO NOT drive any tool between halves to
separate the crankcase. Damage to the sealing
surfaces will result.
Fig. 2-86
AN045
22. Lift the bottom half of the crankcase off the top half.
! CAUTION
! CAUTION
! CAUTION
2
2-21
36. 23. Lift the crankshaft free from the top half of the
crankcase and slide the crankshaft oil seals off the
crankshaft. Account for the C-ring. Remove the
four bearing dowel pins.
24. Remove the oil-injection pump driveshaft from the
lower crankcase half. Account for the thrust washer
on the outer end of the shaft.
Fig. 2-87
AN047
NOTE: Do not replace the inner seals unless the
water pump shows signs of leaking coolant out of
the small bleed hole in the bottom half of the
crankcase. If a water pump seal is to be replaced,
use the Water Pump Bearing and Seal Kit (p/n
0644-084) and see Cleaning and Inspecting Engine
in this section.
25. Place the crankcase on the bench with the water
pump side down. Using the long seal driver, drive
the water pump seal from the crankcase.
Fig. 2-88
AN049
26. Remove the snap ring securing the inner seal in the
crankcase.
27. Using the hooked end of the tool, pull the inner seal
free of the crankcase.
Fig. 2-89
AN050
28. Using a sharp, pointed tool, pry the seal ring from
the backside of the water pump impeller.
Fig. 2-90
AN051
Disassembling Engine
(500/580/600 cc Twin Models)
NOTE: On the 580 cc, remove the ignition timing
sensor from the magneto housing.
1. Using the spanner wrench to secure the flywheel,
remove the flywheel nut, lock washer, and flat
washer; then remove the three starter pulley cap
screws and remove the pulley.
2-22
37. Fig. 2-91
AN015
Fig. 2-92
AN407D
2. Install the Crankshaft Protector Cap (p/n 0644-234)
onto the end of the crankshaft.
Fig. 2-93
AN018
Fig. 2-94
AN408D
NOTE: A suitable substitute protective cap can be
made by welding a 3 mm (1/8 in.) plate on one side
of a spare flywheel nut.
3. Using the Flywheel Puller/Spanner Wrench (p/n
0144-310) or suitable substitute, remove the
flywheel from the crankshaft by tightening the
puller bolt, striking the head of the puller bolt with
a hammer, and tightening again. Repeat this
procedure until the flywheel is free. Account for the
key.
To prevent damage to the crankshaft, the puller
must bottom on the cap and not on the
crankshaft. Also, do not thread puller bolts more
than 12.7 mm (1/2 in.) into the flywheel. Damage
to the coils may result.
Fig. 2-95
AR105
! CAUTION
2
2-23
38. Fig. 2-96
AN410D
NOTE: To ensure the cleanliness of the flywheel
magnets, place the flywheel (with the magnets
facing upward) on a clean bench.
4. On the 500 cc/600 cc, remove the four Allen-head
cap screws securing the magneto case to the
crankcase.
Fig. 2-97
AN412D
5. On the 500 cc/600 cc, remove the Allen-head cap
screws securing the stator to the stator plate.
Fig. 2-98
AN413D
6. Remove the Allen-head cap screws securing the
stator plate. Remove the stator plate from the
engine.
Fig. 2-99
AR106
Fig. 2-100
AN414D
NOTE:The stator plate screws had Loctite applied
to the threads during assembly. Using an impact
driver, apply a sharp blow to the head of each screw
to break the Loctite loose before removal.
7. On the 580 cc, remove the Allen-head screws
securing the stator base. On the 500 cc/600 cc,
remove the ignition timing sensor.
Fig. 2-101
AR107
2-24
39. Fig. 2-102
AN415D
8. Remove the three cap screws securing the
thermostat cap; then remove the cap, gasket, and
thermostat.
9. Remove the spark plugs.
NOTE: On the 580 cc, remove the cap screws
securing the thermostat manifold to the cylinder
heads. Remove the manifold and discard the
gaskets.
10. Remove the cap screws with O-rings securing the
cylinder head(s); then separate from the cylinders.
Account for the O-rings.
11. Remove the oil-injection hose from each cylinder
and the crankcase nozzle.
Fig. 2-103
AN420D
12. Remove the eight nuts (with lock washers and
washers) securing the cylinders to the crankcase;
then using a rubber hammer, gently tap the
cylinders and remove from the crankcase by lifting
them straight up off their studs. Account for
gasket(s) and any alignment bushings.
When removing a cylinder, be sure to support
the piston to prevent damage to the crankcase
and piston.
13. Remove the PTO-side piston-pin circlip from the
PTO-side piston; then remove the MAG-side
piston-pin circlip from the MAG-side piston.
Fig. 2-104
AN315D
14. Using the Piston Pin Puller (p/n 0644-328), remove
the piston pins from both pistons.
NOTE: For proper assembly, keep all MAG-side
components and all PTO-side components
separated. Assemble them on their proper sides.
Fig. 2-105
AN316D
DO NOT use any type of punch to drive the
piston pin free of the piston; damage may result.
Use a piston-pin puller only.
15. Lift the pistons clear of the connecting rods and
remove the small-end connecting-rod bearings
(account for two washers); then remove the piston
rings. Keep each piston with its rings; keep each
piston pin and bearing together as a set.
! CAUTION
! CAUTION
2
2-25
40. Fig. 2-106
AN317D
NOTE: Place rubber bands over the connecting
rods and around the cylinder studs.This will prevent
the connecting rods from damaging the crankcase.
16. On the 500 cc/600 cc, remove the intake manifolds
and reed block assemblies.
Fig. 2-107
AN433D
17. Remove either lower union cap screw securing the
lower check valve assembly; then remove the two
screws, lock washers, and washers securing the
oil-injection pump to the crankcase. Remove the
pump, retainer, and O-ring.
18. Remove the five screws securing the water pump
cover to the crankcase and remove the cover.
Account for the O-ring gasket.
19. Remove the cap screw securing the water pump
impeller; then slide the impeller free of the shaft.
20. Remove the cap screws securing the PTO-end plate
to the crankcase; then remove the plate.
21. Position the crankcase, with its bottom side up, on
two blocks of wood. Remove the cap screws
securing the crankcase halves.
22. Separate the crankcase halves by installing two
crankcase cap screws in opposite corners leaving
the heads approximately 6 mm (1/4 in.) out. Using
a plastic-tipped hammer, tap on each cap screw
head until the case halves separate. Remove the cap
screws.
DO NOT drive any tool between halves to
separate the crankcase. Damage to the sealing
surfaces will result.
Fig. 2-108
AN045
23. Lift the bottom half of the crankcase off the top half.
Care must be taken to not allow the connecting
rods to drop onto the sealing surface of the
bottom case half.
24. Lift the crankshaft free from the top half of the
crankcase and slide the crankshaft oil seals off the
crankshaft. Account for the C-ring. Remove the
bearing dowel pins.
25. Remove the oil-injection pump/water pump
driveshaft from the lower crankcase half. Account
for the thrust washer on the outer end of the shaft.
Fig. 2-109
AN324D
! CAUTION
! CAUTION
2-26
41. NOTE: Do not replace the inner seals unless the
water pump shows signs of leaking coolant out of
the small bleed hole in the bottom half of the
crankcase. If a water pump seal is to be replaced,
use the Water Pump Bearing and Seal Kit (p/n
0644-084).
26. Place the crankcase on the bench with the water
pump side down. Using the long seal driver, drive
the mechanical water pump seal from the
crankcase.
Fig. 2-110
AN325D
27. Using a pair of snap ring pliers, remove the snap
ring securing the inner seal in the crankcase.
28. Using the hooked end of the tool, pull the inner seal
free of the crankcase.
Fig. 2-111
AN326D
29. Using the hooked end of the tool, pry the seal ring
from the backside of the water pump impeller.
Fig. 2-112
AN327D
Disassembling Engine
(700 cc Models)
1. Using a spanner wrench to secure the flywheel,
remove the flywheel nut, lock washer, and flat
washer.
Fig. 2-113
AJ012
2. Using a spanner wrench to secure the crankshaft,
remove the three cap screws from the starter pulley.
Remove the starter pulley.
Fig. 2-114
AJ013
2
2-27
42. 3. Install Protective Cap (p/n 0644-234) onto the end
of the crankshaft.
Fig. 2-115
AJ014
NOTE: A protective cap can be made by welding
a 3 mm (1/8 in.) plate on one end of a spare flywheel
nut.
To prevent damage to the crankshaft, thread a
protective cap onto the crankshaft. The puller
must bottom on the cap and not on the
crankshaft. Also, do not thread puller bolts more
then 12.7 mm (1/2 in.) into the flywheel. Damage
to the coils may result.
4. Using Flywheel Puller (p/n 0144-310), remove the
flywheel from the crankshaft by tightening the
puller bolt, striking the head of the puller bolt with
a brass hammer, and tightening again. Repeat
procedure until the flywheel is free. Account for the
key in the crankshaft keyway.
When installing Flywheel Puller (p/n 0144-310), it
must be installed with its welded side facing
outward or the puller will be damaged.
Fig. 2-116
AJ015
Before applying excessive pressure to the
center flywheel puller bolt, check to make sure
puller bolt is pulling straight. If it is pulling to one
side, the crankshaft will be damaged. Square the
puller using the three bolts that attach the puller
to the flywheel.
NOTE: To ensure the cleanliness of the flywheel
magnets, place the flywheel (with the magnets
facing upward) on a clean bench.
5. Remove the cap screws securing the magneto
housing to the crankcase; then remove the housing.
Fig. 2-117
AJ659
6. Remove the cap screws, lock washers, and washers
securing the stator.
Fig. 2-118
AJ660
7. Remove the rubber grommet from the stator wiring
harness. Slide stator free of the crankshaft and
remove.
8. Remove the cap screws securing the stator backing
plate. Remove the plate from the crankcase.
! CAUTION
! CAUTION
! CAUTION
2-28
43. Fig. 2-119
AJ661
9. Remove the cap screws securing the ignition timing
sensor; then remove the sensor from the engine.
Fig. 2-120
AJ662
10. Remove the three cap screws securing the
thermostat cap; then remove cap, rubber gasket, and
thermostat.
11. Remove the cap screws securing the thermostat
manifold to the cylinder heads. Remove the
manifold and discard gaskets.
Fig. 2-121
AJ022
12. Remove the spark plugs.
13. Remove the eight cap screws and O-rings securing
each head; then separate each head from each
cylinder. Account for two O-rings beneath each
head.
NOTE: Mark each cylinder head, cylinder, and
piston and keep together as an assembly. Mark the
MAG cylinder components #1 and the PTO cylinder
components #2.
Fig. 2-122
AJ023
14. Remove the oil-injection hose from each cylinder
nozzle.
15. Remove the eight cylinder base nuts and four flange
nuts securing the cylinders to the crankcase.
Account for eight flat washers and lock washers.
Using a rubber hammer, gently tap on the side of
each cylinder to free it from the crankcase.
Fig. 2-123
AJ027
16. Slowly lift each cylinder straight up and free of the
studs. Grasp the connecting rod and piston as the
cylinder clears the piston to prevent the rod from
dropping against the crankcase. Remove and save
the cylinder base gaskets.
2
2-29
44. Fig. 2-124
AJ028
As cylinders are removed, lay them on their side
on the workbench. Never set cylinders upright
on any hard surface. The reed stoppers will be
damaged.
17. Remove the four screws securing each reed stopper
to each reed seat. Remove stopper and reed valve
assembly.
Fig. 2-125
AJ058
NOTE: The reed seat can remain on the cylinders
unless it requires service;in which case, remove the
two screws securing the reed seat to the cylinder;
then remove the reed seat and discard the gasket.
18. Remove the PTO-side piston-pin circlip from the
PTO-side piston; remove the MAG-side piston-pin
circlip from the MAG-side piston.
Fig. 2-126
AJ029
19. Using the Piston Pin Puller (p/n 0644-328), remove
the piston pins from both pistons.
Fig. 2-127
AJ030
NOTE: For proper assembly, keep all MAG-side
components and all PTO-side components
separated. Assemble them on their proper sides.
DO NOT use any type of punch to drive the pin
free of the piston; damage may result. Use a
piston-pin puller only.
20. Lift the pistons clear of the connecting rods and
account for two washers. Remove the small-end
connecting-rod bearings; then remove the piston
rings. Keep each piston with its rings; keep each
piston, pin, and bearing together as a set.
! CAUTION
! CAUTION
2-30
45. Fig. 2-128
AQ059
NOTE: Place rubber bands over the connecting
rods and around the cylinder studs. This will keep
the connecting rods from damaging the crankcase.
Fig. 2-129
AJ031
21. Using an impact driver, remove the four screws
securing the PTO-end plate to the crankcase; then
remove the plate.
Fig. 2-130
AJ032
22. Remove the two screws and lock washers securing
the oil-injection pump to the crankcase.
Fig. 2-131
AJ035
Note that the shorter of the two screws securing
the oil pump to the crankcase came from the top
mounting hole of the oil-injection pump. It must
be installed in the same location.
23. Remove the two screws securing the oil-injection
pump retainer to the crankcase. Gently tap on the
retainer with a plastic hammer to free it from the
crankcase. Pull the retainer straight back and free of
the crankcase. Account for the O-ring found around
the inner flange of the retainer sealing surface.
Fig. 2-132
AJ036
NOTE: Account for the shim washer(s) found on
the upper pinion driven shaft. If no shim(s) are
found on the shaft, check the retainer just removed
as they will sometimes stick to the bearing race.
Remove shim(s) and place in a safe place where
they won’t be lost.
24. Remove the five cap screws securing the water
pump cover to the crankcase. Remove the cover and
O-ring seal.
! CAUTION
2
2-31
46. Fig. 2-133
AJ033
NOTE: Do not remove the water pump impeller or
the impeller shaft unless necessary. Only remove
impeller and shaft if there are signs of coolant
leakage from the small hole located in the bottom of
the crankcase directly behind the water pump
housing.
25. Lay the engine on its side and remove the 18 cap
screws securing the crankcase halves. Note the
position of the different-sized cap screws.
Fig. 2-134
AJ038
26. Separate the crankcase halves by installing two
crankcase cap screws in opposite corners leaving
the heads approximately 6 mm (1/4 in.) out. Using
a plastic tipped hammer, tap on each cap screw head
until the case halves separate; then remove the two
cap screws. Remove the rubber bands and lift the
top half of the crankcase off the bottom half. Grasp
the connecting rods as the top half of the crankcase
is removed. Do not allow them to drop onto the
sealing surface of the bottom case half.
DO NOT drive any tool between halves to
separate the crankcase. Damage to the sealing
surfaces will result.
27. Remove the pinion gear from the crankcase;
account for the C-ring.
Fig. 2-135
AJ041
28. Lift the crankshaft free from the crankcase half and
slide the crankshaft oil seals off the ends of the
crankshaft. Account for the C-ring. Slide the
bearing off the PTO-end of crankshaft. Remove the
bearing dowel pins from the crankcase.
DO NOT remove the water pump impeller or
shaft unless necessary. The shaft and impeller
should only be removed from the lower
crankcase half when there is a coolant leakage
problem or a rough inner bearing. To inspect for
either condition, follow steps A through D.
A. Remove the O-ring from the oil-injection pump
retainer. Slide the retainer into position on the shaft
in the lower half of the crankcase.
B. While holding the retainer tight against the
crankcase, rotate the shaft. Bearing rotation must
feel smooth.
Fig. 2-136
AJ044
C. If any roughness is felt, remove the retainer and
inspect its bearing by turning it several revolutions.
If it is smooth, the shaft must then be removed and
the inner bearing inspected. Turn inner bearing by
hand. If any roughness is felt, replace the inner
bearing.
! CAUTION
! CAUTION
2-32
47. D. Check the bottom of the water pump housing for
any signs of coolant leakage. The small hole,
located on the bottom of the crankcase directly
behind the water pump housing, will show coolant
stains if the seal has any leakage problems. If stains
or any signs of leakage are present, remove
impeller and shaft and replace seals.
Fig. 2-137
AJ045
NOTE: For instructions on bearing and seal
replacement, see the appropriate Assembling
Engine sub-section of this manual. Complete steps
29-35 only if there is a bad seal or shaft bearing.
29. Remove the cap screw securing the impeller to the
shaft.
Fig. 2-138
AJ046
30. Slowly pull the shaft from the lower half of the
crankcase.
NOTE: Use the Water Pump Bearing and Seal Kit
(p/n 0644-084) to remove and replace the water
pump bearing and seals.
Fig. 2-139
AJ142
31. Using the special tool, remove the water pump seal
by inserting the tool rod down through the inner
bearing and seal. Position the end of the tool up
against the back side of the metal case of the outer
water pump seal.
Fig. 2-140
AJ143
32. Using a hammer, gently tap on the rod while
moving the end of the tool from side to side of the
seal casing. Repeat until the seal is free of the
crankcase.
Fig. 2-141
AJ144
33. Using the hooked end of the tool, pull the inner seal
free of the crankcase.
2
2-33
48. Fig. 2-142
AJ145
34. Using a pair of snap ring pliers, remove the snap
ring located in front of the water pump bearing.
Fig. 2-143
AJ146
35. Using the bearing driver from the special tool kit,
drive the water pump bearing from the crankcase.
Fig. 2-144
AJ147
Disassembling Engine
(600 cc Triple Models)
1. Using an impact driver or a 6-mm hex wrench,
remove the four cap screws securing the magneto
housing to the crankcase.
2. Using a spanner wrench to secure the crankshaft,
remove the cap screw, lock washer, and large flat
washer securing the flywheel.
3. Remove the three cap screws securing the starter
pulley to the flywheel.
4. To prevent damaging the crankshaft threads during
the flywheel removal procedure, install a
Crankshaft Protector Cap (p/n 0644-234) onto the
end of the crankshaft.
Fig. 2-145
AN162
5. Attach the flywheel puller to the flywheel using
three 8-mm cap screws approximately 2 3/4 in.
long. Thread each of the three cap screws evenly
into the flywheel 1/2 in.
6. Tighten the center puller bolt against the crankshaft
protector on the end of the crankshaft. Continue to
tighten the puller bolt until the flywheel snaps free
of the crankshaft taper. Remove the puller from the
flywheel and place the flywheel, open side up, on a
clean work bench. Account for the flywheel key.
2-34
49. Fig. 2-146
AN161
7. Remove the three Allen-head cap screws securing
the stator to the stator plate.
8. Remove the rubber grommet from the crankcase
and slide the stator free of the crankshaft.
Fig. 2-147
AN160
9. Remove the two Allen-head cap screws securing the
stator backing plate to the crankcase.
Fig. 2-148
AN158
10. Remove the two screws securing the timing sensor;
then loosen the screw securing the wiring harness
retainer tab. Remove the timing sensor from the
crankcase.
Fig. 2-149
AN157
11. Remove the thermostat cover; then remove the
thermostat from the water manifold.
NOTE:The thermostat is designed to open at 50°C
(122°F). It should be checked for proper operation
before installing (see Section 3).
12. Remove the water manifold assembly.
Fig. 2-150
AN156
13. Remove each cylinder head; then account for the
two O-rings under each head.
14. For assembly purposes, number the three heads and
cylinders using a marker. Start from the MAG-side.
Fig. 2-151
AN209
2
2-35
50. 15. Remove the four nuts securing each cylinder to the
crankcase; then carefully lift each cylinder straight
up and free of the piston. Support the piston as the
cylinder clears the piston to prevent the connecting
rod from dropping against the crankcase and
causing damage to the crankcase sealing surface.
Account for two alignment dowel pins per cylinder.
Fig. 2-152
AN207
16. For assembly purposes, number the dome of each
piston starting from the MAG-side; then remove the
MAG-side circlip from each piston.
Fig. 2-153
AN242
17. Using Piston Pin Puller (p/n 0644-328), remove the
piston pin from each piston. Remove the piston,
piston pin bearing, and the two shim washers. Keep
each piston, piston pin, and bearing together as a
set.
Fig. 2-154
AN241
18. Remove the cylinder base gaskets from the
crankcase. Note that the cylinder base gaskets are
aligned with the same dowel sleeves which align
the cylinders on the crankcase.
NOTE: If the cylinder base gaskets are not
damaged, they can be reused.
Fig. 2-155
AN239
19. Remove the two screws securing the oil-injection
pump to the crankcase. Slide the pump free of the
crankcase. Account for the O-ring located around
the pump inner flange.
Fig. 2-156
AQ130D
20. Remove the six cap screws securing the intake
flanges and reed valve assembly to the crankcase.
2-36
51. Fig. 2-157
AN237
21. Remove the intake flange and reed valve assembly.
Be very careful not to damage the reed valve stops.
Place the assembly on its flat side. Remove and
discard and reed valve assembly gasket.
Fig. 2-158
AN236
22. Using an impact driver, remove the five screws
securing the water pump cover to the crankcase and
remove the cover. Account for the O-ring gasket.
Fig. 2-159
AN234
23. Loosen the cap screw securing the water pump
impeller until there is a 1/4-in. space between the
cap screw flange and impeller.
Fig. 2-160
AN233
24. Using a plastic hammer, gently tap on the head of
the cap screw until the impeller is free of the shaft.
Remove the cap screw and impeller.
Fig. 2-161
AN232
25. From the opposite side of the crankcase, remove the
oil pump retainer and shaft. Account for the shaft
thrust washer located between the retainer and shaft
flange.
Fig. 2-162
AN231
26. Using an impact driver, remove the four screws
securing the seal protector plate to the end of the
crankcase; then slide the plate free of the crankshaft.
2
2-37
52. Fig. 2-163
AN230
27. Remove the 14 cap screws securing the two
crankcase halves together.
Fig. 2-164
AN229
28. To separate the crankcase halves, start two of the
crankcase cap screws into the crankcase at opposite
corners. Thread the cap screws into the crankcase
until a 6.4 mm (1/4 in.) space remains between the
cap screw flange and the crankcase surface.
29. Set the crankcase on its side with the flat reed
surfaces resting on the work bench. Using a
hammer, strike the heads of the two cap screws
alternately driving the two case halves apart.
Fig. 2-165
AN227
30. Once there is a 6.4 mm (1/4 in.) space between the two
case halves, set the crankcase down on the work bench
with its bottom side up. Remove the cap screws; then
lift the bottom of the crankcase free of the engine.
Fig. 2-166
AN221
31. Grasp the crankshaft at either end and carefully lift
it from the crankcase. Have a clean area ready to lay
the crankshaft on once it has been removed.
Account for the two crankcase dowel pins.
Fig. 2-167
AN222
32. With the crankshaft removed from the top half of
the crankcase, remove the seven bearing retaining
pins and the C-ring.
Fig. 2-168
AN223
2-38
53. NOTE: Do not replace the inner oil seal or
mechanical seal unless the water pump shows
signs of leaking coolant out of the small bleed hole
in the bottom half of the crankcase. If a water pump
seal is to be replaced, use the Water Pump Bearing
and Seal Kit (p/n 0644-084).
33. Place the crankcase on the bench with the water
pump side down. Using the long seal driver, drive
the water pump seal from the crankcase.
Fig. 2-169
AN226
34. Using a pair of snap ring pliers, remove the snap
ring securing the inner seal in the crankcase.
35. Using the hooked end of the seal driver, pull the
inner seal free of the crankcase.
Fig. 2-170
AN224
36. Using a sharp-pointed tool, pry the seal ring from
the backside of the water pump impeller.
Fig. 2-171
AN051
Disassembling Engine
(800/1000 cc Models)
1. Using an impact driver or a 6-mm hex wrench,
remove the four cap screws securing the magneto
housing to the crankcase. Account for the alignment
dowels.
2. Using an impact driver, remove the five screws
securing the water pump cover. Remove the cover
and account for the O-ring seal and alignment
dowels.
Fig. 2-172
AQ005
3. Secure the crankshaft using a spanner wrench; then
remove the cap screw securing the water pump
impeller.
2
2-39
54. Fig. 2-173
AQ006
4. Remove the water pump impeller from the
counterbalance shaft.
5. With the impeller removed, check the condition of
the seal on the back side. It must be free of any
cracks, chips, or rough areas.
NOTE: If any rough areas are found, the seal ring
can be removed using a small screwdriver. Simply
pry the seal ring upward; then remove the rubber
cup from beneath the seal ring.
Fig. 2-174
AQ008
6. Remove the remaining water pump center and back
section from the counterbalance shaft.
7. Inspect the front mechanical seal and rear seal
surface for any rough areas. If the seals need
replacement, see the appropriate Repairing Water
Pump in Section 3.
Fig. 2-175
AQ010
8. Using a spanner wrench to secure the crankshaft,
remove the cap screw, lock washer, and large flat
washer securing the flywheel.
9. Remove the three cap screws securing the starter
pulley to the flywheel.
10. To prevent damaging the crankshaft threads during
the flywheel removal procedure, use the Puller
Insert (p/n 0644-179) on the end of the crankshaft.
Fig. 2-176
AQ019
11. Attach the flywheel puller to the flywheel using
three 8-mm cap screws approximately 2 3/4 in.
long. Thread each of the three cap screws evenly
into the flywheel 1/2 in.
12. Tighten the center puller bolt against the insert on
the crankshaft. Continue to tighten the puller bolt
until the flywheel snaps free of the crankshaft taper.
Remove the puller from the flywheel and place the
flywheel, open side up, on a clean work bench.
Account for the flywheel key.
2-40
55. Fig. 2-177
AQ020
13. Remove the Allen-head cap screws securing the
stator to the stator plate.
14. Remove the rubber grommet from the crankcase
and slide the stator free of the crankshaft.
Fig. 2-178
AQ021
15. Remove the three Allen-head cap screws securing
the stator plate to the crankcase.
16. Remove the thermostat cover; then remove the
thermostat from the water manifold.
NOTE:The thermostat is designed to open at 50°C
(122°F). It should be checked for proper operation
before installing (see Section 3).
17. Remove the water manifold assembly.
18. Remove the heads from the cylinders. Account for
the two O-rings under each head.
19. For assembly purposes, number the three heads and
cylinders. Start from the MAG-side.
Fig. 2-179
AQ026
20. Remove the four nuts, lock washers, and flat
washers securing each cylinder to the crankcase;
then carefully lift each cylinder straight up and free
of the piston. Support the piston as the cylinder
clears the piston to prevent the connecting rod from
dropping against the crankcase and causing damage
to the crankcase sealing surface.
Fig. 2-180
AQ027
21. For assembly purposes, number the dome of each
piston starting from the MAG-side; then remove the
MAG-side circlip from each piston.
Fig. 2-181
AQ028
2
2-41
56. 22. Using Piston Pin Puller (p/n 0644-328), remove the
piston pin from each piston. Remove the piston,
piston pin bearing, and the two shim washers. Keep
each piston, piston pin, and bearing together as a
set.
Fig. 2-182
AQ029
23. Before lifting the cylinder base gasket from the
crankcase, note how it is installed. The smaller of
the three water passage holes must be positioned to
the MAG-side of the crankcase when installing.
Lift the gasket free of the crankcase.
NOTE: If the cylinder base gasket is not damaged,
it can be reused.
Fig. 2-183
AQ030
24. Remove the two screws securing the oil-injection
pump to the crankcase. Slide the pump free of the
crankcase. Account for the O-ring located around
the pump inner flange.
25. Remove the pump retainer and shaft. Account for
the shaft thrust washer.
Fig. 2-184
AQ119
26. Remove the six cap screws securing the intake
flanges and reed valve assembly to the crankcase.
27. Remove the intake flange and reed valve assembly.
Be very careful not to damage the reed valve stops.
Place the assembly on its flat side. Remove and
discard the reed valve assembly gasket.
Fig. 2-185
AN236
28. Using an impact driver, remove the four screws
securing the PTO-end plate to the end of the
crankcase; then slide the plate free of the
crankshaft.
Fig. 2-186
AQ034
29. Remove the twenty cap screws securing the two
crankcase halves together.
2-42
57. Fig. 2-187
AQ035
30. To separate the crankcase halves, start two of the
crankcase cap screws into the crankcase at opposite
corners. Thread the cap screws into the crankcase
until a 6.4 mm (1/4 in.) space remains between the
cap screw flange and the crankcase surface.
Fig. 2-188
AQ036
31. Set the crankcase on its side with the flat reed
surfaces resting on the work bench. Using a plastic
hammer, strike the heads of the two cap screws
alternately driving the two case halves apart.
32. Once there is a 6.4 mm (1/4 in.) space between the
two case halves, set the crankcase down on the work
bench with its bottom side up. Remove the cap
screws; then lift the bottom of the crankcase free of
the engine.
Fig. 2-189
AQ037
33. Remove the balancer shaft from the crankcase.
Notice that it has a timing mark located on the side
of the drive gear. This timing mark must be aligned
with the crankshaft gear during assembly.
Fig. 2-190
AQ038
34. Remove the balancer shaft end seals from the
crankcase.
35. Grasp the crankshaft at either end and carefully lift
it from the crankcase. Have a clean area ready to lay
the crankshaft on once it has been removed.
Fig. 2-191
AQ039
36. With the crankshaft removed from the top half of
the crankcase, remove the seven bearing dowel pins
and the two C-rings.
Fig. 2-192
AQ040
2
2-43
58. Cleaning and
Inspecting Engine
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is
necessary.
CYLINDER HEADS
1. Using a non-metallic carbon removal tool, remove
any carbon buildup from the combustion chambers
being careful not to nick, scrape, or damage the
combustion chambers or the sealing surfaces.
2. Inspect the spark-plug holes for any damaged
threads. Repair damaged threads using a “heli-coil”
insert.
3. Place the cylinder heads on a Surface Plate (p/n
0644-016) covered with #400 grit wet-or-dry
sandpaper. Using light pressure, move each
cylinder head in a figure eight motion. Inspect the
sealing surface for any indication of high spots. A
high spot can be noted by a bright metallic finish.
Correct any high spots before assembly by
continuing to move the cylinder head in a figure
eight motion until a uniform bright metallic finish
is attained.
Fig. 2-193
AQ132D
Water or parts-cleaning solvent must be used in
conjunction with the wet-or-dry sandpaper or
damage to the sealing surface may result.
CYLINDER HEAD (500/600 cc)
1. Using a non-metallic carbon removal tool, remove
any carbon buildup from the combustion chambers
being careful not to nick, scrape, or damage the
combustion chambers or the sealing surfaces.
2. Inspect the spark-plug holes for any damaged threads.
Repair damaged threads using a “heli-coil” insert.
3. Inspect the cylinder head for flatness using a
straightedge and a feeler gauge. Acceptable
warpage must not exceed 0.05 mm (0.002 in.).
NOTE: If the warpage exceeds specification,
resurface the cylinder head using procedures
identified in step 6 in the Crankcase subsection of
Cleaning and Inspecting Engine.
Fig. 2-194
AN426D
Water or parts-cleaning solvent must be used in
conjunction with the wet-or-dry sandpaper or
damage to the sealing surface may result.
CYLINDERS
1. Using a non-metallic carbon removal tool, remove
carbon buildup from the exhaust ports.
2. Wash the cylinders in parts-cleaning solvent.
3. Inspect the cylinders for pitting, scoring, scuffing,
and corrosion. If marks are found, repair the surface
with Ball Hone (p/n 0644-036) for the 600 cc or
(p/n 0644-037) for the 800 cc or with #500 grit
stones and honing oil.
Fig. 2-195
AN053
! CAUTION
! CAUTION
2-44
59. NOTE: To produce the proper 60° “crosshatch”
pattern, use a low RPM drill (600 RPM) at the rate of
30 strokes per minute. If honing oil is not available,
use a lightweight, petroleum-based oil. Thoroughly
clean the cylinders after honing using detergent
soap and hot water and dry with compressed air;
then immediately apply oil to the cylinder bores. If a
bore is severely damaged or gouged, the cylinder
will have to be replaced.
4. Place the head surface of each cylinder on the
surface plate covered with #400 grit wet-or-dry
sandpaper. Using light pressure, move each
cylinder in a figure eight motion. Inspect the
surface for any indication of high spots. A high spot
can be noted by a bright metallic finish. Correct any
high spots before assembly by continuing to move
the cylinder in a figure eight motion until a uniform
bright metallic finish is attained.
Water or parts-cleaning solvent must be used in
conjunction with the wet-or-dry sandpaper or
damage to the sealing surface may result.
PISTON ASSEMBLY
1. Using a non-metallic carbon removal tool, remove
the carbon buildup from the dome of each piston.
2. Take an old piston ring and snap it into two pieces;
then grind the end of the old ring to a 45° angle and
to a sharp edge. Using the sharpened ring as a tool,
clean carbon from the ring-grooves. Be sure to
position the ring with its tapered side up.
Improper cleaning of the ring-grooves by the use
of the wrong type of ring-groove cleaner will
result in severe damage to the piston.
3. Inspect each piston for cracks in the piston pin and
skirt areas.
4. Inspect each piston for seizure marks or scuffing.
Repair with #400 grit wet-or-dry sandpaper and
water or honing oil.
Fig. 2-196
AN135
NOTE: If scuffing or seizure marks are too deep to
correct with the sandpaper, it will be necessary to
replace the piston.
5. Inspect the perimeter of each piston for signs of
excessive “blowby.” Excessive “blowby” indicates
worn piston rings or an out-of-round cylinder.
CRANKCASE
1. Wash the crankcase halves in parts-cleaning solvent.
NOTE: Before washing the crankcase halves,
make sure the four bearing dowel pins have been
removed and accounted for.
2. Inspect the crankcase halves for scoring, pitting,
scuffing, or any imperfections in the casting.
3. Inspect all threaded areas for damaged or stripped
threads.
4. Inspect the bearing areas for cracks or excessive
bearing movement. If evidence of excessive bearing
movement is noted, repair by peening the bearing
area in a pinking (sawtooth) pattern.
5. Inspect the bearing dowel pins for wear.
6. Inspect the sealing surfaces of the crankcase halves
for trueness by placing each crankcase half on the
surface plate covered with #400 grit wet-or-dry
sandpaper. Using light pressure, move each half in
a figure eight motion. Inspect the sealing surfaces
for any indication of high spots. A high spot can be
noted by a bright metallic finish. Correct any high
spots by continuing to move the half in a figure
eight motion until a uniform bright metallic finish
is attained.
NOTE: Care must be taken not to remove an
excessive amount of aluminum, or the crankcase
will have to be replaced. If excessive aluminum is
removed, too much pre-load will be exerted on the
crankshaft bearings when assembled.
! CAUTION
! CAUTION
2
2-45
60. Fig. 2-197
AN060
Water or parts-cleaning solvent must be used in
conjunction with the wet-or-dry sandpaper or
damage to the sealing surface may result.
INTAKE MANIFOLD
INSULATORS (Single Carburetor)/
ADAPTER PLATES (Twin Carburetor)
NOTE: For fan cooled models only.
1. Inspect for cracks, scoring, pitting, imperfections,
or warping.
2. Inspect the sealing surfaces for trueness by placing
each on the surface plate covered with #400 grit
wet-or-dry sandpaper. Using light pressure, move
both sides in a figure eight motion. Inspect the
sealing surface for any indication of high spots or
warping. Correct high spots by continuing to move
each side in a figure eight motion. Warped
components must be replaced.
NOTE: On the twin carburetor model in order to
inspect adapter plate trueness, it will be necessary
to remove the studs.
Water or parts-cleaning solvent must be used in
conjunction with the wet-or-dry sandpaper or
damage to the sealing surfaces may result.
Fig. 2-198
A932
CRANKSHAFT
1. Wash the crankshaft with bearings in parts-cleaning
solvent.
2. Inspect the bearings for wear, scoring, scuffing,
damage, or discoloration. Rotate the bearings.
Bearings must rotate freely and must not bind or
feel rough. If any abnormal condition is noted,
replace the bearing.
Fig. 2-199
AN218
3. Inspect the connecting-rod bearings by rotating
them. The bearings must rotate freely and must not
bind or feel rough. If a connecting-rod bearing must
be replaced, the connecting rod and crank pin must
also be replaced.
Fig. 2-200
AN217
! CAUTION
! CAUTION
2-46
61. 4. Inspect the oil-injection pump drive gear for any
signs of worn or chipped teeth. If either condition
exists, replace the gear.
Fig. 2-201
AQ043
NOTE: Lubricate bearings thoroughly prior to
assembly.
REMOVING OUTER
CRANKSHAFT BEARINGS
! WARNING
Safety glasses must be worn when spreading
bearings.
NOTE: Steps 1-3 are for removing the MAG-side
bearing.
1. Place a bearing support (block of wood, etc.)
beneath the MAG-side bearing.
A bearing support must be positioned beneath
the bearing that is being removed to prevent
crankshaft damage.
2. Drive a chisel or bearing splitter between the
bearing race and crankshaft counterweight until the
bearing is spread far enough to install the jaws of
the crankshaft bearing remover.
3. Place the protective cap on the crankshaft end; then
using the Crankshaft Bearing Remover (p/n
0144-302), remove the bearing from the end of the
crankshaft. Account for any shim(s). Note the
position of the dowel pin hole.
Fig. 2-202
AQ045
4. The PTO-side bearing may be removed simply by
sliding the bearing off the PTO end.
Fig. 2-203
AN151A
5. Inspect the crankshaft bearing area for wear. If any
wear is noted on either end, replace the crankshaft
end.
INSTALLING OUTER
CRANKSHAFT BEARINGS
NOTE: Steps 1-3 are for installing the MAG-side
bearing.
1. Wrap a thick towel around the crankshaft; then
secure the crankshaft vertically in a vise.
2. Heat the bearing either by placing the entire bearing
in a pan of oil on a hot plate or by squirting oil into
the bearing and using a propane torch to heat the
inner race of the bearing until a slight smoke is
noted coming from the bearing.
DO NOT overheat the bearing.
! CAUTION
! CAUTION
2
2-47
62. 3. Place any shims removed during disassembly onto
the crankshaft; then slide the bearing onto the
crankshaft making sure the dowel-pin hole in the
outer race is properly positioned and will align with
its hole and pin in the crankcase.
4. Slide the PTO-side bearing onto the PTO end
making sure the dowel-pin hole will align with the
hole and pin in the crankcase.
Fig. 2-204
AN151A
BALANCER SHAFT (800/1000 CC)
1. Inspect the balancer shaft bearings by rotating them
by hand. The bearings must rotate freely without
binding or feeling rough. If either condition exists,
replace the bearing. Inspect the balancer gear very
closely for any chipped teeth or signs of wear. If
either condition exists, replace the gear.
Fig. 2-205
AQ044
REED ASSEMBLY
1. Inspect the reed valves, stoppers, and valve blocks
for cracks or any deterioration.
Fig. 2-206
AQ046
2. Wash the reed valves, stopper, and cage assembly in
parts-cleaning solvent and blow dry.
3. Inspect the reed stopper height. Using a caliper,
measure the distance from the seat to the bottom
outer tip edge of the stopper. Measurement must not
exceed specifications. If measurement is not within
specifications, either bend or replace the reed
stopper.
Fig. 2-207
AJ156
4. Inspect the reed-to-seat clearance. Using a feeler
gauge, measure the clearance. Clearance must be
less than 0.20 mm (0.008 in.). If clearance is not
within specifications, replace the reed valve.
5. To assemble, place the reed valves on the cage with
its clipped corner positioned to the lower right hand
corner of the cage. Place the reed stopper assembly
into position and secure with the three screws
coated with red Loctite #271.
2-48
63. Fig. 2-208
AQ047
Measuring Critical
Components
NOTE: Critical engine component specifications
are on pages 51-52 of this section.
CYLINDER TRUENESS
1. Measure each cylinder in the three locations from
front to back and side to side for a totalofsixreadings.
Fig. 2-209
AN302
2. The trueness (out-of-roundness) is the difference
between the highest and lowest reading. Maximum
trueness (out-of-roundness) must not exceed
specifications.
Fig. 2-210
0725-586
CYLINDER TRUENESS LIMIT (max)
mm in.
0.10 0.004
PISTON SKIRT/CYLINDER CLEARANCE
1. Measure each cylinder front to back about 2.5 cm
(1 in.) from the bottom of each cylinder.
2. Measure the corresponding piston skirt diameter at
a point 1 cm (0.394 in.) above the piston skirt at a
right angle to the piston-pin bore. Subtract this
measurement from the measurement in step 1. The
difference (clearance) must be within
specifications.
Fig. 2-211
AC091
PISTON-RING END GAP
1. Place each piston ring in the wear portion above the
exhaust port of its respective cylinder. Use the
piston to position each ring squarely in each
cylinder.
2. Using a feeler gauge, measure each piston-ring end
gap. Acceptable ring end gap must be within
specifications.
2
2-49