The document provides specifications and details for Mitsubishi 4G1 series engines, including:
- Service specifications for parts like rocker arms and camshaft.
- Dimensions that must be within tolerance for parts to be re-used.
- Torque specifications for fasteners throughout the engine.
- Details on sealants, gaskets and special tools needed for repairs.
- Sections covering the alternator, timing belt, fuel system, cooling and various engine components.
Es un material muy valioso, que es parte del funcionamiento automóvil, donde fluye la cantidad de corriente.
Los temas de la electricidad automotriz son fundamentos de la innovación tecnológica, los temas son:
Batería.
Arrancador.
Alternador.
Es importante saber la función que cumplen cada uno de los elementos del motor diésel, válvulas cuando se deben cambiar, guías de válvulas , bielas, pistones, metales y camiseta de cilindro.
VOLVO EC460B LC EC460BLC EXCAVATOR Service Repair Manualfujdfjjskrtekme
This is the Highly Detailed factory service repair manual for theVOLVO EC460B LC EC460BLC EXCAVATOR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.VOLVO EC460B LC EC460BLC EXCAVATOR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
General
Safety
1 Standard Parts, Service
2 Engine with Mounting and Equipment
3 Elec. System, Warning System, Information System, Instruments
4 Power Transmission
5 Frame and Crawler Unit
6 Machinery House, Cab, Exterior Trim Parts Anywhere
7 Hydraulic System, Digging, Handling, Grading Equipment
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveVOLVO EC460B LC EC460BLC EXCAVATOR Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
Es un material muy valioso, que es parte del funcionamiento automóvil, donde fluye la cantidad de corriente.
Los temas de la electricidad automotriz son fundamentos de la innovación tecnológica, los temas son:
Batería.
Arrancador.
Alternador.
Es importante saber la función que cumplen cada uno de los elementos del motor diésel, válvulas cuando se deben cambiar, guías de válvulas , bielas, pistones, metales y camiseta de cilindro.
VOLVO EC460B LC EC460BLC EXCAVATOR Service Repair Manualfujdfjjskrtekme
This is the Highly Detailed factory service repair manual for theVOLVO EC460B LC EC460BLC EXCAVATOR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.VOLVO EC460B LC EC460BLC EXCAVATOR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
General
Safety
1 Standard Parts, Service
2 Engine with Mounting and Equipment
3 Elec. System, Warning System, Information System, Instruments
4 Power Transmission
5 Frame and Crawler Unit
6 Machinery House, Cab, Exterior Trim Parts Anywhere
7 Hydraulic System, Digging, Handling, Grading Equipment
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveVOLVO EC460B LC EC460BLC EXCAVATOR Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
2010 POLARIS 600 RUSH PRO-RIDE SNOWMOBILE Service Repair Manualplopoi drert
This is the Highly Detailed factory service repair manual for the2010 POLARIS 600 RUSH PRO-RIDE SNOWMOBILE, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.2010 POLARIS 600 RUSH PRO-RIDE SNOWMOBILE Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
General Information
Maintenance
Engine / Cooling / Exhaust
Cleanfire Fuel Injection
Final Drive / Brakes
PVT System
Shocks
Steering and Suspensions
Chassis
Battery / Electrical
Wiring Diagrams
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to have2010 POLARIS 600 RUSH PRO-RIDE SNOWMOBILE Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
This is the Highly Detailed factory service repair manual for theMERCURY MERCRUISER MARINE ENGINE V-8 DIESEL, D7.3L D-TRONIC 1998 , this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.MERCURY MERCRUISER MARINE ENGINE V-8 DIESEL, D7.3L D-TRONIC 1998 Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Important Information
Removal and Installation
Engine Mechanical
Electrical System
Fuel System
Cooling Sytem
Intake and Exhaust System
Power Steering System
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveMERCURY MERCRUISER MARINE ENGINE V-8 DIESEL, D7.3L D-TRONIC 1998 Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
This is the Highly Detailed factory service repair manual for theMERCURY MERCRUISER MARINE ENGINE V-8 DIESEL, D7.3L D-TRONIC 1998 , this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.MERCURY MERCRUISER MARINE ENGINE V-8 DIESEL, D7.3L D-TRONIC 1998 Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Important Information
Removal and Installation
Engine Mechanical
Electrical System
Fuel System
Cooling Sytem
Intake and Exhaust System
Power Steering System
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveMERCURY MERCRUISER MARINE ENGINE V-8 DIESEL, D7.3L D-TRONIC 1998 Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
8
Enterprise Excellence is Inclusive Excellence.pdfKaiNexus
Enterprise excellence and inclusive excellence are closely linked, and real-world challenges have shown that both are essential to the success of any organization. To achieve enterprise excellence, organizations must focus on improving their operations and processes while creating an inclusive environment that engages everyone. In this interactive session, the facilitator will highlight commonly established business practices and how they limit our ability to engage everyone every day. More importantly, though, participants will likely gain increased awareness of what we can do differently to maximize enterprise excellence through deliberate inclusion.
What is Enterprise Excellence?
Enterprise Excellence is a holistic approach that's aimed at achieving world-class performance across all aspects of the organization.
What might I learn?
A way to engage all in creating Inclusive Excellence. Lessons from the US military and their parallels to the story of Harry Potter. How belt systems and CI teams can destroy inclusive practices. How leadership language invites people to the party. There are three things leaders can do to engage everyone every day: maximizing psychological safety to create environments where folks learn, contribute, and challenge the status quo.
Who might benefit? Anyone and everyone leading folks from the shop floor to top floor.
Dr. William Harvey is a seasoned Operations Leader with extensive experience in chemical processing, manufacturing, and operations management. At Michelman, he currently oversees multiple sites, leading teams in strategic planning and coaching/practicing continuous improvement. William is set to start his eighth year of teaching at the University of Cincinnati where he teaches marketing, finance, and management. William holds various certifications in change management, quality, leadership, operational excellence, team building, and DiSC, among others.
Buy Verified PayPal Account | Buy Google 5 Star Reviewsusawebmarket
Buy Verified PayPal Account
Looking to buy verified PayPal accounts? Discover 7 expert tips for safely purchasing a verified PayPal account in 2024. Ensure security and reliability for your transactions.
PayPal Services Features-
🟢 Email Access
🟢 Bank Added
🟢 Card Verified
🟢 Full SSN Provided
🟢 Phone Number Access
🟢 Driving License Copy
🟢 Fasted Delivery
Client Satisfaction is Our First priority. Our services is very appropriate to buy. We assume that the first-rate way to purchase our offerings is to order on the website. If you have any worry in our cooperation usually You can order us on Skype or Telegram.
24/7 Hours Reply/Please Contact
usawebmarketEmail: support@usawebmarket.com
Skype: usawebmarket
Telegram: @usawebmarket
WhatsApp: +1(218) 203-5951
USA WEB MARKET is the Best Verified PayPal, Payoneer, Cash App, Skrill, Neteller, Stripe Account and SEO, SMM Service provider.100%Satisfection granted.100% replacement Granted.
Skye Residences | Extended Stay Residences Near Toronto Airportmarketingjdass
Experience unparalleled EXTENDED STAY and comfort at Skye Residences located just minutes from Toronto Airport. Discover sophisticated accommodations tailored for discerning travelers.
Website Link :
https://skyeresidences.com/
https://skyeresidences.com/about-us/
https://skyeresidences.com/gallery/
https://skyeresidences.com/rooms/
https://skyeresidences.com/near-by-attractions/
https://skyeresidences.com/commute/
https://skyeresidences.com/contact/
https://skyeresidences.com/queen-suite-with-sofa-bed/
https://skyeresidences.com/queen-suite-with-sofa-bed-and-balcony/
https://skyeresidences.com/queen-suite-with-sofa-bed-accessible/
https://skyeresidences.com/2-bedroom-deluxe-queen-suite-with-sofa-bed/
https://skyeresidences.com/2-bedroom-deluxe-king-queen-suite-with-sofa-bed/
https://skyeresidences.com/2-bedroom-deluxe-queen-suite-with-sofa-bed-accessible/
#Skye Residences Etobicoke, #Skye Residences Near Toronto Airport, #Skye Residences Toronto, #Skye Hotel Toronto, #Skye Hotel Near Toronto Airport, #Hotel Near Toronto Airport, #Near Toronto Airport Accommodation, #Suites Near Toronto Airport, #Etobicoke Suites Near Airport, #Hotel Near Toronto Pearson International Airport, #Toronto Airport Suite Rentals, #Pearson Airport Hotel Suites
[Note: This is a partial preview. To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
Sustainability has become an increasingly critical topic as the world recognizes the need to protect our planet and its resources for future generations. Sustainability means meeting our current needs without compromising the ability of future generations to meet theirs. It involves long-term planning and consideration of the consequences of our actions. The goal is to create strategies that ensure the long-term viability of People, Planet, and Profit.
Leading companies such as Nike, Toyota, and Siemens are prioritizing sustainable innovation in their business models, setting an example for others to follow. In this Sustainability training presentation, you will learn key concepts, principles, and practices of sustainability applicable across industries. This training aims to create awareness and educate employees, senior executives, consultants, and other key stakeholders, including investors, policymakers, and supply chain partners, on the importance and implementation of sustainability.
LEARNING OBJECTIVES
1. Develop a comprehensive understanding of the fundamental principles and concepts that form the foundation of sustainability within corporate environments.
2. Explore the sustainability implementation model, focusing on effective measures and reporting strategies to track and communicate sustainability efforts.
3. Identify and define best practices and critical success factors essential for achieving sustainability goals within organizations.
CONTENTS
1. Introduction and Key Concepts of Sustainability
2. Principles and Practices of Sustainability
3. Measures and Reporting in Sustainability
4. Sustainability Implementation & Best Practices
To download the complete presentation, visit: https://www.oeconsulting.com.sg/training-presentations
Implicitly or explicitly all competing businesses employ a strategy to select a mix
of marketing resources. Formulating such competitive strategies fundamentally
involves recognizing relationships between elements of the marketing mix (e.g.,
price and product quality), as well as assessing competitive and market conditions
(i.e., industry structure in the language of economics).
What is the TDS Return Filing Due Date for FY 2024-25.pdfseoforlegalpillers
It is crucial for the taxpayers to understand about the TDS Return Filing Due Date, so that they can fulfill your TDS obligations efficiently. Taxpayers can avoid penalties by sticking to the deadlines and by accurate filing of TDS. Timely filing of TDS will make sure about the availability of tax credits. You can also seek the professional guidance of experts like Legal Pillers for timely filing of the TDS Return.
Unveiling the Secrets How Does Generative AI Work.pdfSam H
At its core, generative artificial intelligence relies on the concept of generative models, which serve as engines that churn out entirely new data resembling their training data. It is like a sculptor who has studied so many forms found in nature and then uses this knowledge to create sculptures from his imagination that have never been seen before anywhere else. If taken to cyberspace, gans work almost the same way.
Falcon stands out as a top-tier P2P Invoice Discounting platform in India, bridging esteemed blue-chip companies and eager investors. Our goal is to transform the investment landscape in India by establishing a comprehensive destination for borrowers and investors with diverse profiles and needs, all while minimizing risk. What sets Falcon apart is the elimination of intermediaries such as commercial banks and depository institutions, allowing investors to enjoy higher yields.
The world of search engine optimization (SEO) is buzzing with discussions after Google confirmed that around 2,500 leaked internal documents related to its Search feature are indeed authentic. The revelation has sparked significant concerns within the SEO community. The leaked documents were initially reported by SEO experts Rand Fishkin and Mike King, igniting widespread analysis and discourse. For More Info:- https://news.arihantwebtech.com/search-disrupted-googles-leaked-documents-rock-the-seo-world/
Digital Transformation and IT Strategy Toolkit and TemplatesAurelien Domont, MBA
This Digital Transformation and IT Strategy Toolkit was created by ex-McKinsey, Deloitte and BCG Management Consultants, after more than 5,000 hours of work. It is considered the world's best & most comprehensive Digital Transformation and IT Strategy Toolkit. It includes all the Frameworks, Best Practices & Templates required to successfully undertake the Digital Transformation of your organization and define a robust IT Strategy.
Editable Toolkit to help you reuse our content: 700 Powerpoint slides | 35 Excel sheets | 84 minutes of Video training
This PowerPoint presentation is only a small preview of our Toolkits. For more details, visit www.domontconsulting.com
Kseniya Leshchenko: Shared development support service model as the way to ma...Lviv Startup Club
Kseniya Leshchenko: Shared development support service model as the way to make small projects with small budgets profitable for the company (UA)
Kyiv PMDay 2024 Summer
Website – www.pmday.org
Youtube – https://www.youtube.com/startuplviv
FB – https://www.facebook.com/pmdayconference
Affordable Stationery Printing Services in Jaipur | Navpack n PrintNavpack & Print
Looking for professional printing services in Jaipur? Navpack n Print offers high-quality and affordable stationery printing for all your business needs. Stand out with custom stationery designs and fast turnaround times. Contact us today for a quote!
13. 4G1 ENGINE (E - W) - Specifications 11A-1-3
REWORK DIMENSIONS
Item Standard Limit
Cylinder head and valves
Cylinder head oversize valve guide SOHC 12-VALVE 0.05 O. S. 12.050 - 12.068 -
hole diameter mm
0.25 O. S. 12.250 - 12.268 -
0.50 O. S. 12.500 - 12.518 -
SOHC 16-VALVE 0.05 O. S. 10.550 - 10.568 -
0.25 O. S. 10.750 - 10.768 -
0.50 O. S. 11.000 - 11.018 -
DOHC 0.05 O. S. 10.550 - 10.568 -
0.25 O. S. 10.750 - 10.768 -
0.50 O. S. 11.000 - 11.018 -
Oversize valve seat SOHC Intake (primary) 0.3 O. S. 27.300 - 27.325 -
ring hole diameter 12-VALVE
mm 0.6 O. S. 27.600 - 27.625 -
Intake (secondary) 0.3 O. S. 32.300 - 32.325 -
0.6 O. S. 32.600 - 32.625 -
Exhaust 0.3 O. S. 35.300 - 35.325 -
0.6 O. S. 35.600 - 35.625 -
SOHC Intake 0.3 O. S. 28.300 - 28.321 -
16-VALVE
<4G13> 0.6 O. S. 28.600 - 28.621 -
Exhaust 0.3 O. S. 26.300 - 26.321 -
0.6 O. S. 26.600 - 26.621 -
SOHC Intake 0.3 O. S. 30.300 - 30.321 -
16-VALVE
<4G18> 0.6 O. S. 30.600 - 30.621 -
Exhaust 0.3 O. S. 28.300 - 28.321 -
0.6 O. S. 28.600 - 28.621 -
DOHC Intake 0.3 O. S. 31.300 - 31.325 -
0.6 O. S. 31.600 - 31.625 -
Exhaust 0.3 O. S. 27.800 - 27.825 -
0.6 O. S. 28.100 - 28.125 -
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Revised
14. 11A-1-4 4G1 ENGINE (E - W) - Specifications
TORQUE SPECIFICATIONS
Item Nm
Alternator and ignition system
Water pump pulley bolt 9
Alternator brace (alternator side) 22
Alternator brace (tightened with water pump) 23
Alternator pivot bolt 44
Oil level gauge guide 23
Crankshaft bolt 125
Spark plug 25
Distributor 11
Ignition coil 10
Camshaft position sensor 9
Camshaft position sensor support 13
Camshaft position sensing cylinder 21
Timing belt
Timing belt cover 11
Timing belt tensioner 23
Crankshaft angle sensor (Rear wheel drive) 9
Engine support bracket (left) 35
Idler pulley 35
Camshaft sprocket bolt 88
Fuel system
Delivery pipe 11
Fuel pressure regulator 9
Throttle body 18
Fuel pump 11
Breather tube 22
Carburetor 17
Air temperature sensor 13
EGR valve 21
Water pump
Water inlet fitting 22
Water inlet pipe assembly 12
Water inlet pipe M6 12
M8 25
Fitting (Rear wheel drive) 23
Water outlet fitting (Rear wheel drive) 23
Thermostat case 23
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Revised
15. 4G1 ENGINE (E - W) - Specifications 11A-1-5
Item Nm
Thermo valve 27
Water temperature gauge unit 11
Water temperature sensor 29
Water pump 13
Exhaust manifold and intake manifold
Boost sensor 5
Solenoid valve assembly 9
Intake manifold 17
Intake manifold stay (MPI) M8 17
M10 21
Intake manifold stay (carburetor) 29
Exhaust manifold cover 29
Exhaust manifold M8 17
M10 29
Oxygen sensor 44
Rocker arms, rocker shafts, and camshaft
Fuel pump cover 12
Rocker cover 4
Rocker shaft assembly 31
Adjusting screw 15
Bearing cap 24
11
Cylinder head and valves
Cylinder head bolt 20 + 90_ + 90_
Tighten to 49 Nm, then completely loosen and retighten as described.
Oil pump and oil pan
Transmission stay 23
Oil pan 7
Drain plug 39
Oil screen 18
Front case 13
Relief plug 44
Oil pump cover 10
Pistons and connecting rods
Connecting rod nut 17 + 90_ to 100_
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Revised
16. 11A-1-5a 4G1 ENGINE (E - W) - Specifications
Item Nm
Crankshaft and cylinder block
Flywheel 132
Drive plate 132
Rear plate 10
Bell housing cover 10
Rear oil seal case 11
Bearing cap bolt 51
Oil pressure switch 18
Knock sensor 23
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Added
18. 11A-1-6 4G1 ENGINE (E - W) - Specifications
NEW TIGHTENING METHOD USING PLASTIC REGION TIGHTENING BOLTS
Parts of the engine use plastic region tightening bolts. The tightening procedure for these is different
from that of conventional bolts and is described in relevant parts of this manual. Note that plastic region
tightening bolts have fixed service limits. These limits are indicated in relevant parts of this manual and
must be strictly observed.
D Plastic region tightening bolts are used for the following applications:
(1) Cylinder head bolts
(2) Connecting rod cap bolts
D The tightening procedure is basically as follows:
After tightening a bolt to the specified torque, tighten it by a further 90 _ + 90_ or by a further 90–100°.
The exact tightening procedure differs depending on the bolt and is described in relevant parts of
this manual.
SEALANTS
Item Specified sealant Quantity
Water pump Mitsubishi Genuine Part No. MD970389 or equivalent As required
Thermo valve Mitsubishi Genuine Part No. MD970389 or equivalent As required
Engine coolant temperature sensor 3M Nut Locking Part No. 4171 or equivalent As required
Engine coolant temperature gauge unit 3M ATD Part No. 8660 or equivalent As required
Camshaft bearing cap 3M ATD Part No. 8660 or equivalent As required
Semi-circular packing 3M ATD Part No. 8660 or equivalent As required
Rocker cover 3M ATD Part No. 8660 or equivalent As required
Front oil seal case Mitsubishi Genuine Part No. MD970389 or equivalent As required
Oil pump Mitsubishi Genuine Part No. MD970389 or equivalent As required
Oil pressure switch 3M ATD Part No. 8660 or equivalent As required
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
19. 4G1 ENGINE (E - W) - Specifications 11A-1-7
FORM-IN-PLACE GASKET
The engine has several areas where the form-in-place gasket (FIPG) is in use. To ensure that the gasket
fully serves its purpose, it is necessary to observe some precautions when applying the gasket. Bead
size, continuity and location are of paramount importance. Too thin a bead could cause leaks. Too thick
a bead, on the other hand, could be squeezed out of location, causing blocking or narrowing of the
fluid feed line. To eliminate the possibility of leaks from a joint, therefore, it is absolutely necessary to
apply the gasket evenly without a break, while observing the correct bead size.
The FIPG used in the engine is a room temperature vulcanization (RTV) type and is supplied in a 100-gram
tube (Part No. MD970389 or MD997110). Since the RTV hardens as it reacts with the moisture in the
atomospheric air, it is normally used in the metallic flange areas. The FIPG, Part No. MD970389, can
be used for sealing both engine oil and coolant, while Part No. 997110 can only be used for engine
oil sealing.
Disassembly
The parts assembled with the FIPG can be easily disassembled without use of a special method. In
some cases, however, the sealant between the joined surfaces may have to be broken by lightly striking
with a mallet or similar tool. A flat and thin gasket scraper may be lightly hammered in between the
joined surfaces. In this case, however, care must be taken to prevent damage to the joined surfaces.
For removal of the oil pan, the special tool “Oil Pan Remover” (MD998727) is available. Be sure to use
the special tool to remove the oil pan. <Except aluminium die-cast oil pans>
Surface Preparation
Thoroughly remove all substances deposited on the gasket application surfaces, using a gasket scraper
or wire brush. Check to ensure that the surfaces to which the FIPG is to be applied is flat. Make sure
that there are no oils, greases and foreign substances deposited on the application surfaces. Do not
forget to remove the old sealant remained in the bolt holes.
Form-In-Place Gasket Application
When assembling parts with the FIPG, you must observe some precautions, but the procedures is very
simple as in the case of a conventional precut gasket.
Applied FIPG bead should be of the specified size and without breaks. Also be sure to encircle the
bolt hole circumference with a completely continuous bead. The FIPG can be wiped away unless it is
hardened. While the FIPG is still moist (in less than 15 minutes), mount the parts in position. When
the parts are mounted, make sure that the gasket is applied to the required area only. In addition, do
not apply any oil or water to the sealing locations or start the engine until a sufficient amount of time
(about one hour) has passed after installation is completed.
The FIPG application procedure may vary on different areas. Observe the procedure described in the
text when applying the FIPG.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
21. 4G1 ENGINE (E - W) - Special Tools 11A-2-1
2. SPECIAL TOOLS
Tool Number Name Use
MB990767 End yoke holder Holding camshaft sprocket when loosening or
tightening bolt (used with MD998715)
MD998011 Crankshaft rear oil Installation of crankshaft rear oil seal
seal installer
MD998054 Oil pressure switch Removal and installation of oil pressure switch
wrench
MD998304 Crankshaft front oil Installation of crankshaft front oil seal
seal installer
MD998305 Crankshaft front oil Guide for installation of crankshaft front oil seal
seal guide
MD998713 Camshaft oil seal Installation of camshaft oil seal
installer
MD998715 Pin (2-off) Holding camshaft sprocket when loosening or
tightening bolt (used with MB990767)
MD998727 Oil pan remover Removal of oil pan
MD998735 Valve spring com- Compression of valve springs
pressor
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
22. 11A-2-2 4G1 ENGINE (E - W) - Special Tools
Tool Number Name Use
MD998760 Valve stem seal Installation of valve stem seals
installer (SOHC 12-VALVE)
MD998780 Piston pin setting Removal and press-fitting of piston pins
tool
MB991659 Guide-D Guide for removal and press-fitting of piston
pins
MD998772 Valve spring com- Compression of valve springs
pressor
MD998440 Leak-down tester Testing of automatic lash adjusters
(DOHC)
MD998442 Air bleed wire Testing of automatic lash adjusters
(DOHC)
MD998781 Flywheel stopper Locking flywheel in fixed position
MB991671 Valve stem Press-fitting of valve stem seals
installer (SOHC 16-VALVE, DOHC)
MB991653 Cylinder head bolt Removal and installation of cylinder head bolt
wrench (10)
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Revised
27. 4G1 ENGINE (E - W) - Alternator and Ignition System 11A-3-3
REMOVAL SERVICE POINT
AA" CRANKSHAFT BOLT REMOVAL
MD998781
(1) Lock the flywheel or drive plate in position using the special
tool shown in the illustration, then loosen the crankshaft
bolts.
INSTALLATION SERVICE POINTS
"AA DISTRIBUTOR INSTALLATION
(1) Turn the crankshaft clockwise until cylinder No. 1 is at
Alignment mark top dead center on its compression stroke.
(2) Align the alignment marks on the distributor housing and
coupling.
(3) Fit the distributor onto the engine, aligning the stud bolts
with the slots in the distributor mounting flange.
Alignment mark
"BA CRANKSHAFT BOLT INSTALLATION
(1) Lock the flywheel or drive plate in position using the special
MD998781 tool shown in the illustration, then tighten the crankshaft
bolts.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
29. 4G1 ENGINE (E - W) - Timing Belt 11A-4-1
4. TIMING BELT
REMOVAL AND INSTALLATION <SOHC>
12
13
11
88 Nm
11 Nm 1
10
5
23 Nm
35 Nm
8
9 6
3
4 7
9 Nm
2
Removal steps
1. Timing belt upper cover 7. Crankshaft sprocket
2. Timing belt lower cover 8. Spacer <Rear wheel drive>
AA" "CA 3. Timing belt 9. Sensing blade <Rear wheel drive>
"BA 4. Tensioner spring AB" "AA 10. Camshaft sprocket bolt
"BA 5. Timing belt tensioner 11. Camshaft sprocket
6. Crankshaft angle sensor 12. Engine support bracket
<Rear wheel drive> 13. Timing belt rear cover
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Revised
30. 11A-4-2 4G1 ENGINE (E - W) - Timing Belt
REMOVAL AND INSTALLATION <DOHC>
12
11 Nm 11 Nm
3 13
11 Nm
9
1
88 Nm
8
23 Nm
5
11
10
6 35 Nm
35 Nm
7
4
2
Removal steps
1. Timing belt upper cover AB" "AA 8. Camshaft sprocket bolt
2. Timing belt lower cover 9. Camshaft sprocket
AA" "DA 3. Timing belt 10. Engine support bracket
AA" "BA 4. Tensioner spring 11. Timing belt rear cover (lower)
AA" "BA 5. Timing belt tensioner 12. Timing belt rear cover (right)
6. Idler pulley 13. Timing belt rear cover (left)
7. Crankshaft pulley
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
31. 4G1 ENGINE (E - W) - Timing Belt 11A-4-3
REMOVAL SERVICE POINTS
AA" TIMING BELT / TENSIONER SPRING / TIMING
BELT TENSIONER REMOVAL
(1) Using pliers, grip the tensioner spring projection (marked
“A” in the diagram)and remove it from the oil pump case
stopper. Then, remove the tensioner spring.
(2) Remove the timing belt tensioner.
(3) If the timing belt is to be reused, chalk an arrow on the
belt to indicate the direction of rotation before removing
it. This will ensure the timing belt is fitted correctly when
reused.
AB" CAMSHAFT SPROCKET BOLT REMOVAL
MD998715
(1) Using the special tools shown in the illustration, lock the
MB990767 camshaft sprocket in position.
(2) Loosen the camshaft sprocket bolt.
INSPECTION
1. TIMING BELT
Check the timing belt closely. Replace the belt with a new
one if any of the following defects is evident:
(1) Hardened backing rubber (the backing rubber is glossy,
non-elastic, and so hard that scratching with fingernails
leaves no mark)
Crack Crack
(2) Surface cracks in the backing rubber
(3) Splits in the canvas and/or separation of the canvas and
rubber
(4) Cracks at the bases of teeth
(5) Cracks in the side of the belt
Separation
Cracked side
Cracked tooth base
(6) Abnormal wear on the belt’s sides
Rounded edge
NOTE
The sides of the belt are normal if they are sharp as
if cut by a knife.
Abnormal wear
(exposed core wire)
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
32. 11A-4-4 4G1 ENGINE (E - W) - Timing Belt
(7) Abnormal wear on teeth
Canvas worn exposing Initial stage:
rubber
Canvas worn (fluffy canvas fibers, rubbery texture gone,
white discoloration, canvas texture indistinct)
Missing tooth
Final stage:
Canvas worn, exposing rubber (tooth width reduced)
(8) Missing teeth
2. TENSIONER PULLEY AND IDLER PULLEY
(1) Check that the pulleys turn smoothly without play and
are not abnormally noisy. Replace either or both of the
pulleys if necessary.
INSTALLATION SERVICE POINTS
"AA CAMSHAFT SPROCKET BOLT INSTALLATION
MB990767 (1) Using the special tools shown in the illustration, lock the
camshaft sprocket in position.
(2) Tighten the camshaft sprocket bolt to the specified torque.
MD998715
"BA TIMING BELT TENSIONER / TENSIONER SPRING
INSTALLATION
(1) Lock the timing belt tensioner in the illustrated position.
Timing belt
tensioner
(2) Fit one of the tensioner spring projections over the hooked
portion of the timing belt tensioner and fit the tensioner
onto the oil pump case.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
33. 4G1 ENGINE (E - W) - Timing Belt 11A-4-5
(3) Grip the other tensioner spring projection and fit it onto
the oil pump case lug as shown in the illustration.
(4) Move the timing belt tensioner in the direction shown
and temporarily tighten the bolt.
"CA TIMING BELT INSTALLATION
(1) Align the camshaft timing mark with the timing mark on
the cylinder head.
(2) Align the crankshaft timing mark with the timing mark
on the front case.
(3) Keeping the tension side of the timing belt tight, fit the
timing belt onto the crankshaft sprocket, camshaft
sprocket, and tensioner pulley in that order.
(4) Loosen the tensioner pulley mounting bolts by 1/4 to
1/2 of a turn and allow the tensioner spring to apply tension
to the timing belt.
(5) Turn the crankshaft twice in the normal rotating direction
(clockwise) and check that the timing marks are correctly
aligned.
Caution
This procedure utilizes the camshaft’s driving torque
to apply tension evenly to the timing belt. Be sure
to turn the crankshaft as described above. Do not
turn the crankshaft in reverse.
(6) Tighten the tensioner pulley mounting bolts.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
34. 11A-4-6 4G1 ENGINE (E - W) - Timing Belt
"DA TIMING BELT INSTALLATION
(1) Place the camshaft sprocket timing marks at the positions
shown.
NOTE
After aligning the sprocket timing marks, let go of the
sprockets. The exhaust camshaft sprocket will rotate by
one tooth in the direction shown and remain stable in
this position.
(2) Align the crankshaft timing mark with the timing mark
on the front case.
(3) Turn the exhaust camshaft sprocket in the direction shown
and fit the timing belt with the timing marks aligned.
(4) Use a bulldog clip to prevent the timing belt teeth from
jumping.
(5) Fit the timing belt onto the idler pulley, crankshaft sprocket,
and tensioner pulley in that order.
NOTE
When fitting the belt, keep the camshaft sprocket timing
marks correctly aligned and keep the tension side of the
belt tight.
(6) Loosen the tensioner pulley mounting bolts by 1/4 to 1/2
of a turn and allow the tensioner spring to apply tension
to the timing belt.
(7) Remove the bulldog clip.
(8) Turn the crankshaft twice in the normal rotating direction
(clockwise) and check that the timing marks are correctly
aligned.
Caution
This procedure utilizes the camshaft’s driving torque
to apply tension evenly to the timing belt. Be sure
to turn the crankshaft as described above. Do not
turn the crankshaft in reverse.
(9) Tighten the tensioner pulley mounting bolts.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
35. 4G1 ENGINE (E - W) - Fuel and Emission Control Systems 11A-5-1
5. FUEL AND EMISSION CONTROL SYSTEMS
REMOVAL AND INSTALLATION <SOHC - CARBURETOR>
17 Nm
7
8
9
2
3
10 21 Nm
11
4
12
5
6
11 Nm
22 Nm
1
Removal steps
1. Breather tube 7. Carburetor
2. Fuel hose 8. Upper gasket
3. Fuel pump 9. Spacer
4. Gasket 10. Lower gasket
5. Insulator 11. EGR valve (vehicles with automatic
6. Gasket transmission for GCC only)
12. Gasket
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
40. 11A-5-4 4G1 ENGINE (E - W) - Fuel and Emission Control Systems
INSTALLATION SERVICE POINTS
"AA INJECTOR INSTALLATION
(1) Fit a new O-ring and grommet onto the injector.
(2) Apply spindle oil or gasoline to the injector O-ring.
(3) Fit the injector onto the delivery pipe, turning it to the
left and right as it goes in.
(4) Check that the injector rotates smoothly.
Caution
If the injector does not rotate smoothly, its O-ring
may be binding. If this occurs, remove the injector
from the delivery pipe, check the O-ring, and re-insert
the injector.
"BA FUEL PRESSURE REGULATOR INSTALLATION
(1) Apply a little new engine oil to the O-ring, then insert
the fuel pressure regulator into the delivery pipe, taking
care not to damage the O-ring.
Caution
Ensure that no engine oil enters the delivery pipe.
(2) Check that the fuel pressure regulator rotates smoothly.
If it does not rotate smoothly, the O-ring may be binding.
If this occurs, remove the fuel pressure regulator, check
the O-ring for damage, then re-insert the regulator into
the delivery pipe.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
41. 4G1 ENGINE (E - W) - Water Pump and Water Hose 11A-6-1
6. WATER PUMP AND WATER HOSE
REMOVAL AND INSTALLATION <SOHC - CARBURETOR>
1 22 Nm
2
27 Nm
27 Nm
4 11 Nm
12
3 5
11 6 7
8
9
23 Nm
10
12 Nm
14
13
13 Nm
Removal steps
1. Water hose "CA 8. Thermostat
2. Water hose 9. Thermostat case
3. Water hose 10. Gasket
"FA 4. Thermo valve (engines with EGR) "BA 11. Water inlet pipe
"FA 5. Thermo valve "BA 12. O-ring
"DA 6. Water temperature gauge unit "BA 13. O-ring
7. Water inlet fitting "AA 14. Water pump
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
42. 11A-6-2 4G1 ENGINE (E - W) - Water Pump and Water Hose
REMOVAL AND INSTALLATION <SOHC - MPI>
11 22 Nm
2 6
29 Nm 7
3
11 Nm
12 Nm
4
8
9
5
23 Nm
10
1
12
13 Nm
Removal steps
1. Water hose 8. Gasket
2. Water hose "BA 9. Water inlet pipe
"EA 3. Water temperature sensor "BA 10. O-ring
"DA 4. Water temperature gauge unit "BA 11. O-ring
5. Water inlet fitting "AA 12. Water pump
"CA 6. Thermostat
7. Thermostat case
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
43. 4G1 ENGINE (E - W) - Water Pump and Water Hose 11A-6-2a
REMOVAL AND INSTALLATION <SOHC 16-VALVE - MPI - FRONT WHEEL DRIVE>
2
12 Nm
1
9
12 Nm
29 Nm
11
23 Nm
10
3
12
8
7
4 6
5
11 Nm
13 Nm 22 Nm
Removal steps
1. Water hose 8. Gasket
2. Water hose "BA 9. Water inlet pipe
"EA 3. Water temperature sensor "BA 10. O-ring
"DA 4. Water temperature gauge unit "BA 11. O-ring
5. Water inlet fitting "AA 12. Water pump
"CA 6. Thermostat
7. Thermostat case
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Added
44. 11A-6-2b 4G1 ENGINE (E - W) - Water Pump and Water Hose
REMOVAL AND INSTALLATION <SOHC 16-VALVE - MPI - REAR WHEEL DRIVE>
12 Nm 23 Nm
2
1 5
6
12 Nm
10
11 7
25 Nm
9
29 Nm
3 8
4
11 Nm
12
23 Nm
13 Nm
Removal steps
1. Water hose "CA 7. Thermostat
2. Water hose 8. Fitting
"EA 3. Water temperature sensor 9. Gasket
"DA 4. Water temperature gauge unit "BA 10. Water inlet pipe
5. Water outlet fitting "BA 11. O-ring
6. Gasket "AA 12. Water pump
E Mitsubishi Motors Corporation Nov. 1995
Dec. 1998 PWEE9520
PWEE9520-A Added
45. 4G1 ENGINE (E - W) - Water Pump and Water Hose 11A-6-3
REMOVAL AND INSTALLATION <DOHC>
12 Nm
11
2
1
12 Nm
29 Nm
8
7 3 22 Nm
9
10 6
12
23 Nm 4
5
11 Nm
13 Nm
Removal steps
1. Water hose 8. Gasket
2. Water hose "BA 9. Water inlet pipe
"EA 3. Water temperature sensor "BA 10. O-ring
"DA 4. Water temperature gauge unit "BA 11. O-ring
5. Water inlet fitting "AA 12. Water pump
"CA 6. Thermostat
7. Thermostat case
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
46. 11A-6-4 4G1 ENGINE (E - W) - Water Pump and Water Hose
INSTALLATION SERVICE POINTS
"AA WATER PUMP INSTALLATION
(1) Apply a 3 mm bead of form-in-place gasket (FIPG) to
the mounting surface.
Specified sealant:
Mitsubishi Genuine Part No. MD970389 or
equivalent.
"BA O-RING / WATER PIPE INSTALLATION
(1) Replace the water inlet pipe O-rings with new ones, then
apply water to the O-rings so that they can be inserted
easily into the water pump and thermostat case.
Caution
1. Do not apply engine oil or any other oily substance
to the O-rings.
2. Secure the water pipe after the thermostat case
has been installed.
"CA THERMOSTAT INSTALLATION
(1) Fit the thermostat such that its jiggle valve is at the top.
"DA WATER TEMPERATURE GAUGE UNIT
INSTALLATION
(1) If the water temperature gauge unit is to be reused, apply
the specified sealant to its thread.
Specified sealant:
3M ATD Part No. 8660 or equivalent.
"EA WATER TEMPERATURE SENSOR INSTALLATION
(1) If the water temperature sensor is to be reused, apply
the specified sealant to its thread.
Specified sealant:
3M Nut Locking Part No. 4171 or equivalent.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520
47. 4G1 ENGINE (E - W) - Water Pump and Water Hose 11A-6-5
"FA THERMO VALVE INSTALLATION
(1) If the thermo valve is to be reused, apply the specified
sealant to its thread.
Specified sealant:
Mitsubishi Genuine Part No. MD970389 or
equivalent.
E Mitsubishi Motors Corporation Nov. 1995 PWEE9520