This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fjjksekksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves draining oil, removing mounting screws and pipes, and removing the pump assembly. Installation requires cleaning, inspecting parts, lubricating with oil, and securing everything with screws.
Removing the water pump requires draining coolant, loosening hoses and clamps, and removing mounting screws. Installation involves installing a new gasket, securing with screws treated with sealant or locktite, filling the system, and reattaching hoses.
Removal of the water temperature regulator involves draining cool
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fujsjefksekmfm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes the removal and installation procedures in step-by-step detail, highlighting important safety notices and precautions. The removal procedure for the engine oil pump involves removing mounting screws and other components. The installation procedure describes cleaning, inspecting, and lubricating parts before securing the pump with mounting screws. The water pump removal requires draining coolant and removing mounting screws and hoses. Installation involves installing a new gasket and securing the pump with threadlocked mounting screws.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ujdjfjjkskkmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ufjjdkfkksmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fusjejfjksaekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes:
1. Removing the oil pan and suction pipe before removing the engine oil pump assembly from the cylinder block using setscrews.
2. Cleaning and inspecting oil pump components before installation and lubricating parts with oil.
3. Installing the oil pump assembly using setscrews and checking backlash after installation.
4. Draining coolant before removing the water pump and fan. Removing the water pump involves setscrews and installing involves a new gasket and setscrews with sealant.
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...jfjkskekfsmem
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3056C engine. It describes the removal and installation procedures in detail with illustrations and notes about cleaning, inspecting, and replacing components. The key steps are to drain fluids, remove mounting hardware, clean mating surfaces, install new seals or gaskets, and reinstall components in the reverse order of removal while torquing fasteners to the specified values.
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...ufjsjekfksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves removing the oil pan, suction pipe, and setscrews to detach the pump assembly. When installing, the procedure describes cleaning components, lubricating with oil, and tightening setscrews.
Removing the water pump requires draining coolant, loosening hoses, and removing setscrews. Installation involves installing a new gasket, tightening setscrews, and refilling the cooling system.
Removal of the water temperature regulator involves draining coolant below the component
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...ufdjjskefksmem
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves removing the oil pan, suction pipe, and setscrews to detach the pump assembly. When installing, the procedure describes cleaning components, lubricating with oil, and tightening setscrews.
Removing the water pump requires draining coolant, loosening hoses, and removing setscrews and gasket. Installation involves inspecting gears, installing a new gasket with guide bolts, and tightening setscrews.
Removing the water temperature regulator involves draining coolant
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fjjksekksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves draining oil, removing mounting screws and pipes, and removing the pump assembly. Installation requires cleaning, inspecting parts, lubricating with oil, and securing everything with screws.
Removing the water pump requires draining coolant, loosening hoses and clamps, and removing mounting screws. Installation involves installing a new gasket, securing with screws treated with sealant or locktite, filling the system, and reattaching hoses.
Removal of the water temperature regulator involves draining cool
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fujsjefksekmfm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes the removal and installation procedures in step-by-step detail, highlighting important safety notices and precautions. The removal procedure for the engine oil pump involves removing mounting screws and other components. The installation procedure describes cleaning, inspecting, and lubricating parts before securing the pump with mounting screws. The water pump removal requires draining coolant and removing mounting screws and hoses. Installation involves installing a new gasket and securing the pump with threadlocked mounting screws.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ujdjfjjkskkmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...ufjjdkfkksmme
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine. The procedures describe draining fluids, removing mounting hardware, and installing new seals and gaskets. Safety notices are included to handle fluids properly and avoid injury from spring-loaded components.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fusjejfjksaekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes:
1. Removing the oil pan and suction pipe before removing the engine oil pump assembly from the cylinder block using setscrews.
2. Cleaning and inspecting oil pump components before installation and lubricating parts with oil.
3. Installing the oil pump assembly using setscrews and checking backlash after installation.
4. Draining coolant before removing the water pump and fan. Removing the water pump involves setscrews and installing involves a new gasket and setscrews with sealant.
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...jfjkskekfsmem
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3056C engine. It describes the removal and installation procedures in detail with illustrations and notes about cleaning, inspecting, and replacing components. The key steps are to drain fluids, remove mounting hardware, clean mating surfaces, install new seals or gaskets, and reinstall components in the reverse order of removal while torquing fasteners to the specified values.
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...ufjsjekfksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves removing the oil pan, suction pipe, and setscrews to detach the pump assembly. When installing, the procedure describes cleaning components, lubricating with oil, and tightening setscrews.
Removing the water pump requires draining coolant, loosening hoses, and removing setscrews. Installation involves installing a new gasket, tightening setscrews, and refilling the cooling system.
Removal of the water temperature regulator involves draining coolant below the component
Caterpillar cat 434 f backhoe loader (prefix ldh) service repair manual (ldh0...ufdjjskefksmem
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves removing the oil pan, suction pipe, and setscrews to detach the pump assembly. When installing, the procedure describes cleaning components, lubricating with oil, and tightening setscrews.
Removing the water pump requires draining coolant, loosening hoses, and removing setscrews and gasket. Installation involves inspecting gears, installing a new gasket with guide bolts, and tightening setscrews.
Removing the water temperature regulator involves draining coolant
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission planetary system of a 637G Wheel Tractor. It outlines 50 steps to fully disassemble the transmission, including removing clutch housings, carrier assemblies, shafts, gears, plates, rings, seals and other components. Special care must be taken when removing components under spring pressure. Various tools are required to properly support, secure and remove parts from the transmission.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides assembly instructions for a torque converter in a 637G wheel tractor-scraper. It details 31 steps to assemble the torque converter, including installing seals, gears, shafts, bearings and housings in the proper order and with specified torques. It also provides disassembly instructions for the transfer gears in 18 steps, removing components like seals, bolts, cages and shafts. Tools required include drivers, pullers, link brackets and dial indicators.
This document provides assembly instructions for a torque converter in a 637G wheel tractor. It outlines 33 steps to assemble the various components of the torque converter like bearings, seals, gears, and housing. Proper cleaning and torque specifications are noted. Additionally, the document describes disassembly and assembly procedures for transfer gears in the wheel tractor, including removing 18 components like bolts, seals, and bearings. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
This document provides instructions for removing and installing a cylinder head, lifter group, and camshaft on a Caterpillar 3408E or 3412E engine. The removal process involves detaching various components and hoses from the cylinder head and loosening bolts. Special tools are required to safely lift and handle parts due to their heavy weight. The installation follows the reverse order and specifies applying sealant and oil to parts and tightening bolts in a sequence with a torque wrench. Precautions are given to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the transmission of a 637E wheel tractor. It lists 47 steps to disassemble the transmission and 21 steps to reassemble it. Some key parts that are disassembled include the housing assembly, planetary group, carrier assemblies, gears, discs, plates, pistons, shafts, seals, springs, snap rings, and bearings. The instructions provide details on removing and installing each part using various tools. Weights of the major components are provided to aid in removal and installation.
This document provides instructions for disassembling and assembling the torque converter of a 627H Wheel Tractor. It describes 18 steps to disassemble the torque converter by removing various parts like retaining rings, bolts, seals, bearings, and assemblies. It then describes 24 steps to reassemble the torque converter by installing these same parts in the reverse order. The document includes illustrations and lists any required tools for each step.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing gears, bearing cages, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including pressing bearings onto gears, installing cups and cages, adjusting shims to achieve proper end play, and torquing bolts. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing bearing cages, gears, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including cleaning parts, pressing bearings onto gears, adjusting shim thickness to achieve proper end play, and torquing bolts to the specified values. Tools required are also listed.
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission planetary system of a 637G Wheel Tractor. It outlines 50 steps to fully disassemble the transmission, including removing clutch housings, carrier assemblies, shafts, gears, plates, rings, seals and other components. Special care must be taken when removing components under spring pressure. Various tools are required to properly support, secure and remove parts from the transmission.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides assembly instructions for a torque converter in a 637G wheel tractor-scraper. It details 31 steps to assemble the torque converter, including installing seals, gears, shafts, bearings and housings in the proper order and with specified torques. It also provides disassembly instructions for the transfer gears in 18 steps, removing components like seals, bolts, cages and shafts. Tools required include drivers, pullers, link brackets and dial indicators.
This document provides assembly instructions for a torque converter in a 637G wheel tractor. It outlines 33 steps to assemble the various components of the torque converter like bearings, seals, gears, and housing. Proper cleaning and torque specifications are noted. Additionally, the document describes disassembly and assembly procedures for transfer gears in the wheel tractor, including removing 18 components like bolts, seals, and bearings. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
This document provides instructions for removing and installing a cylinder head, lifter group, and camshaft on a Caterpillar 3408E or 3412E engine. The removal process involves detaching various components and hoses from the cylinder head and loosening bolts. Special tools are required to safely lift and handle parts due to their heavy weight. The installation follows the reverse order and specifies applying sealant and oil to parts and tightening bolts in a sequence with a torque wrench. Precautions are given to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the transmission of a 637E wheel tractor. It lists 47 steps to disassemble the transmission and 21 steps to reassemble it. Some key parts that are disassembled include the housing assembly, planetary group, carrier assemblies, gears, discs, plates, pistons, shafts, seals, springs, snap rings, and bearings. The instructions provide details on removing and installing each part using various tools. Weights of the major components are provided to aid in removal and installation.
This document provides instructions for disassembling and assembling the torque converter of a 627H Wheel Tractor. It describes 18 steps to disassemble the torque converter by removing various parts like retaining rings, bolts, seals, bearings, and assemblies. It then describes 24 steps to reassemble the torque converter by installing these same parts in the reverse order. The document includes illustrations and lists any required tools for each step.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing gears, bearing cages, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including pressing bearings onto gears, installing cups and cages, adjusting shims to achieve proper end play, and torquing bolts. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing bearing cages, gears, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including cleaning parts, pressing bearings onto gears, adjusting shim thickness to achieve proper end play, and torquing bolts to the specified values. Tools required are also listed.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293101
Engine Oil Pump - Remove - Engines Without a Balancer
SMCS - 1304-011
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
Note: This procedure is for the removal of the engine oil pump on engines that are not equipped
with a balancer. Refer to this Disassembly and Assembly Manual, "Balancer Group - Remove" for
information on the removal of the engine oil pump on engines that are equipped with a balancer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01147907
1. Remove the setscrews (3) and the suction pipe (4).
2. Remove the setscrews (1). Remove the assembly of the engine oil pump (2) from the
cylinder block.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. If necessary, remove the pressure relief valve (5) from the assembly of the engine oil pump
(4). Refer to this Disassembly and Assembly Manual, "Engine Oil Relief Valve - Remove
and Install".
2/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00956631
4. Remove the setscrews (8). Remove engine oil pump (9).
5. If necessary, remove the setscrews and remove the front cover assembly from the engine oil
pump (7) in order to inspect the components within the engine oil pump.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:29:28 UTC+0800 2019
3/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293102
Engine Oil Pump - Install - Engines Without a Balancer
SMCS - 1304-012
Installation Procedure
Note: This procedure is for the installation of the engine oil pump on engines that are not
equipped with a balancer. Refer to this Disassembly and Assembly Manual, "Balancer Group -
Install" for information on the installation of the engine oil pump on engines that are equipped
with a balancer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
If any of the parts on the engine oil pump are worn or damaged, the
entire pump must be replaced.
1. Clean all of the internal components of the oil pump if the front cover of the oil pump was
previously removed in order to inspect the internal components. Check the internal
components for wear and for other damage. Check the clearance between the outer rotor of
the oil pump and the oil pump body. Check the clearance between the outer rotor and the
inner rotor. Check the end play movement of the rotor. Refer to the Systems
Operation/Testing and Adjusting Manual, "Engine Oil Pump - Inspect". Replace the engine
oil pump if any of the components are worn or damaged.
1/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 2. Lubricate the inner rotor and the outer rotor of the engine oil pump with clean engine
lubricating oil. Install the front cover of the engine oil pump onto the body of the oil pump.
Install the setscrews and tighten the setscrews in order to secure the front cover to the body.
Illustration 1 g00956778
3. Install the engine oil pump (9) into the assembly of the engine oil pump (2). Install the
setscrews (8). Tighten the setscrews to a torque of 9 N·m (80 lb in).
4. Fill engine oil pump (9) with clean engine oil.
5. Position the assembly of the engine oil pump (2) against the cylinder block. Ensure that
dowel pin (10) and hollow dowel (11) are correctly located in the cylinder block.
6. Install the setscrews (1). Tighten the setscrews to a torque of 44 N·m (32 lb ft).
7. Check the backlash between the idler gear of the oil pump and the crankshaft gear. Refer to
the Specifications Manual, "Gear Group - Front" for further information.
2/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01147909
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8. If the pressure relief valve (5) was removed, install the pressure relief valve. Refer to this
Disassembly and Assembly Manual, "Engine Oil Relief Valve - Remove and Install" for
further information.
9. Position the suction pipe (4) and install the setscrews (3).
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:30:24 UTC+0800 2019
3/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293115
Water Pump - Remove and Install
SMCS - 1361-011; 1361-012
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the coolant
capacity of the engine.
2. Loosen the clamps and remove the hose from the water pump inlet.
Illustration 1 g00952695
3. Remove the setscrews (3) that fasten the water pump (4) to the front housing (1).
4. If necessary, tap the water pump with a soft hammer in order to loosen the water pump.
5. Remove water pump (4). Remove the gasket (2) from the front housing and the water pump.
Discard the gasket (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-3263 Thread Lock -
B -
Guide Bolt
(M8 X 1.25 by 70 mm)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 1. Inspect the drive gear for the water pump for wear or other damage. If necessary, replace the
drive gear.
2. Clean the joint faces of the water pump and the front housing.
Note: Do not use sealant on the gasket for the water pump.
Illustration 2 g00952716
3. Install Tooling (B) in the front housing (1).
4. Install a new gasket (2) on the front housing.
3/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g00952731
5. Install the water pump (4) on the front housing.
Note: New setscrews have sealant on the first 13 mm (0.5 inch) of the threads. In order to
reuse the old setscrews, clean the old sealant from the setscrews and apply Tooling (A) to
the setscrews.
6. Install the setscrews (3) that fasten the water pump to the front housing. Do not tighten the
setscrews at this time.
7. Remove Tooling (B) and install the remaining setscrews in order to secure the water pump
to the front housing.
Note: Tighten the setscrews evenly in order to pull the water pump into the front housing.
8. Tighten the setscrews (3) to a torque of 22 N·m (16 lb ft). Tighten the setscrews in the
sequence that is shown in Illustration 3.
9. Install the hose to the water pump inlet. Tighten the hose clamps.
10. Fill the cooling system with coolant. Refer to Operation and Maintenance, "Refill
Capacities" for the cooling system capacity.
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:31:21 UTC+0800 2019
4/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293128
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system to a level below the water temperature regulator
into a suitable container for storage or disposal.
1/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 2. Loosen the hose clamp from the upper radiator hose and remove the upper radiator hose
from the water temperature regulator housing.
Illustration 1 g00953937
3. Remove the setscrews (2) that hold the water temperature regulator housing (1) in position
on the cylinder head. Remove the water temperature regulator housing. Remove the O-ring
seal from the water temperature regulator housing. Discard the O-ring.
4. Squeeze the retainers (A) and rotate the water temperature regulator in order to release the
water temperature regulator from the tabs of the water temperature regulator housing.
5. Refer to Systems Operation, Testing and Adjusting, "Water Temperature Regulator - Test"
for the correct procedure on testing the water temperature regulator.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the water temperature regulator housing.
2/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g00953937
2. Position the water temperature regulator (3) in the water temperature regulator housing.
Squeeze the retainers (A) and rotate the water temperature regulator in order to secure the
water temperature regulator to the water temperature regulator housing.
Note: The retainers (A) must be inserted behind the tabs of the water temperature regulator
housing in order to secure the water temperature regulator during engine operation.
3. Install a new O-ring seal on the water temperature regulator housing (1). Lubricate the O-
ring seal with red rubber grease. Position the water temperature regulator housing on the
cylinder head.
4. Install the setscrews (2) that fasten water temperature regulator housing (1) to the cylinder
head.
5. Install the upper radiator hose and tighten the hose clamps. Refer to the Torque
Specifications Manual for the correct torque.
6. Fill the cooling system to the proper level. Refer to the Operation and Maintenance Manual,
"Refill Capacities" for further information.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:32:18 UTC+0800 2019
3/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293555
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt (1/2 inch - 20 NF by 4 inch) 2
B 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01148312
Typical example
1. Remove the two setscrews and install the Tooling (A) as guides.
Note: The weight of the flywheel (2) is approximately 54 kg (119 lb). Install the Tooling
(B) in order to support the flywheel (2) before the remainder of the setscrews (1) are
removed.
2. Remove the remaining setscrews (1) that secure flywheel (2) to the crankshaft.
3. Remove the flywheel (2) from the engine.
2/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g01148313
4. Check the condition of the ring gear (4). Remove the ring gear (4) if the ring gear is worn or
damaged.
Note: Identify the orientation of the ring gear (4) on the flywheel (2) and the position of the
chamfer on the teeth for the correct positioning when the new ring gear is installed.
5. Place the flywheel (2) and the ring gear (4) on a suitable support. Use a hammer and a chisel
in order to remove the ring gear (4) from the flywheel (2).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:33:15 UTC+0800 2019
3/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i07030444
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - 20 NF by 4 inch)
2
B 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks, refer to this Disassembly and Assembly Manual, "Crankshaft Rear Seal -
Remove" for the correct procedure.
1/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00909349
Always wear protective gloves when handling parts that have been
heated.
Note: If ring gear (3) has been removed from flywheel (2). Identify the orientation of ring
gear (3) on the flywheel for the correct positioning when the new ring gear is installed.
2. Heat the ring gear to 250 °C (480 °F) in an oven to install the ring gear onto the flywheel.
Ensure that the orientation of the ring gear is correct and quickly install the ring gear onto
the flywheel.
Note: Do not use a torch to heat the ring gear.
3. Clean flywheel (2) and ring gear (3) when the ring gear has cooled.
2/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01148312
4. Install the Tooling (A) on the crankshaft. Install the Tooling (B) and a suitable lifting device
on flywheel (2) and position the flywheel in the flywheel housing. The weight of the
flywheel is approximately 54 kg (119 lb).
5. Install bolts (1) to flywheel (2).
6. Remove Tooling (A). Install the remaining bolts (1) that secure flywheel (2) to the
crankshaft. Tighten the bolts (1) to a torque of 140 N·m (103 lb ft).
7. Check the alignment of flywheel (2) with the crankshaft. Refer to Testing and Adjusting,
"Flywheel - Inspect" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:34:11 UTC+0800 2019
3/3
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293665
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00991388
Note: The crankshaft rear seal is nonserviceable. If the crankshaft rear seal is removed, the
complete housing assembly must be replaced.
1. Remove the setscrews (1) from the housing assembly (2).
2. Remove the housing assembly (2) from the cylinder block. Discard the housing assembly
(2).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 4 22:35:08 UTC+0800 2019
2/2
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 442E BACKHOE LOADER EME
Configuration: 442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02293676
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing for the crankshaft rear seal are manufactured as a
one-piece assembly. The assembly of the crankshaft rear seal uses ten setscrews in order to fasten
the assembly to the cylinder block.
Note: The following procedure assumes that the crankshaft rear seal is a replacement assembly.
Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the crankshaft
flange before installation.
Note: An installation sleeve (2) is supplied with the new housing assembly. The installation sleeve
must be in place when housing assembly is installed on the crankshaft flange in order to prevent
damage to the crankshaft rear seal during assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 1. Ensure that the crankshaft flange (1) is clean, dry and free from rough metal edges. Ensure
that the face of the cylinder block and the bridge in the crankcase are clean and dry.
Illustration 1 g01148393
2. Remove the packaging from the new assembly of the crankshaft rear seal (3). Ensure that
the plastic sleeve (2) is squarely installed within the seal of the assembly of the crankshaft
rear seal (3). The plastic sleeve (2) is included in order to protect the lip of the seal as the lip
is pushed over the crankshaft flange (1).
Illustration 2 g01004958
Typical example
3. Place the assembly of the crankshaft rear seal (3) over the crankshaft flange (1) and engage
the plastic sleeve (2) onto the crankshaft flange.
2/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. 4. Ensure that the plastic sleeve (2) is engaged onto the crankshaft flange (1). Push the
assembly of the crankshaft rear seal (3) evenly and push the assembly smoothly onto the
crankshaft flange (1) until the assembly is against the cylinder block. During this process,
the plastic sleeve (2) will be forced out of the assembly of the crankshaft rear seal (3).
Discard the plastic sleeve (2).
5. Rotate the assembly of the crankshaft rear seal (3) in order to align the setscrew holes in the
assembly with the setscrew holes in the rear face of the cylinder block.
6. Install the setscrews (5) in order to position housing assembly (3) to the cylinder block. Do
Not tighten the bolts.
7. Place the Tooling (A) over housing assembly (2). This will center the housing assembly
onto the crankshaft flange (3).
Illustration 3 g01148495
8. Tighten the setscrews (1) in numerical order to a torque of 22 N·m (16 lb ft). Do not tighten
the setscrews (X) at this time.
9. Remove the Tooling (A). Tighten the setscrews (X) to a torque of 22 N·m (16 lb ft).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
3/4
442E Backhoe Loader EME00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...