Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM00001 and up).pdf

Service Repair Manual
Models
320C U and 320C LU
Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR CLM
Configuration: 320C U 320C LU Excavators CLM00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01972490
Pump Drive Group - Disassemble - Auxiliary
SMCS - 3108-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7600 Slide Hammer Puller Group 1
4C-5648 Male Adapter Kit 1
B
1U-7600 Slide Hammer Puller Group 1
4C-5663 Female Adapter Kit 1
Threaded Rod (M 12)
150 mm (5.9 inch)
1
Start By:
a. Remove the auxiliary pump drive. Refer to Disassembly and Assembly, "Pump Drive Group
- Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
1/6(W)
w
2019/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...

Illustration 1 g01023965
1. Remove alignment pins (1).
2. Remove bolts (2). Remove cover (3).
3. Remove O-ring seal (4) from cover (3).
2/6(W)
w
2019/10/19

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

4. Use Tooling (A) in order to remove shaft (4A) and the bearing.
5. Remove Tooling (A) from the shaft.
6. Remove bearing (5) and the bearing race from shaft (4A).
3/6(W)
w
2019/10/19

7. Remove gear (6) from the body.
8. Remove bearing (7) and the bearing race from the body.
9. Remove bolts (8). Remove cover (9).
4/6(W)
w
2019/10/19

10. Remove O-ring seal (10) from cover (9).
11. Use Tooling (B) in order to remove shaft (11) and the bearings from the body.
5/6(W)
w
2019/10/19

12. Remove bearing (12) from shaft (11).
13. Remove bearing (13) from shaft (11).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 19 15:29:52 UTC+0800 2019
6/6(W)
w
2019/10/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01972506
Pump Drive Group - Assemble - Auxiliary
SMCS - 3108-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
1. Lower the temperature of bearing (12).
2. Install bearing (12) in the body.
1/5(W)
w
2019/10/19

4. Install bearing (13) in cover (9).
5. Lower the temperature of shaft (11).
6. Install shaft (11) into bearing (12).
2/5(W)
w
2019/10/19

7. Install new O-ring seal (10) on cover (9).
8. Install cover (9). Install bolts (8).
10. Install bearing (7) in the body.
3/5(W)
w
2019/10/19

11. Position gear (6) in the body.
Note: Make sure that you align the gear and the shaft while you install the shaft.
12. Install shaft (4A) in the gear and in the bearing.
14. Install bearing (5) and the bearing race in the body.
4/5(W)
w
2019/10/19

15. Install new O-ring seal (4) on cover (3).
16. Install cover (3). Install bolts (2).
17. Install alignment pins (1).
End By:
a. Install the auxiliary pump drive. Refer to Disassembly and Assembly, "Pump Drive Group -
Install".
Sat Oct 19 15:30:53 UTC+0800 2019
5/5(W)
w
2019/10/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01785957
Pump Drive Group - Install - Auxiliary
SMCS - 3108-012
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1. Install gasket (3).
1/2(W)
w
2019/10/19

2. Install auxiliary pump drive (2). The weight of auxiliary pump drive (2) is approximately
23 kg (51 lb).
3. Install bolts (1).
End By:
a. Install the auxiliary hydraulic pump. Refer to Disassembly and Assembly, "Auxiliary
Hydraulic Pump - Install".
Sat Oct 19 15:31:54 UTC+0800 2019
2/2(W)
w
2019/10/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01968883
Flow Divider Valve - Remove
SMCS - 5097-011; 5137-011
Removal Procedure
Start By:
a. Remove the main control valve.
Table 1
Required Tools
ZZ
6V-9508 Face Seal Plug 6
6V-9829 Cap As 6
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR IN THE INSTALLATION. THIS
INFORMATION IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED
SERVICEMAN.
Reference: Refer to Disassembly and Assembly, "Main Control Valve - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3(W)
w
2019/10/19

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: A hydraulic oil sample should be obtained before any maintenance is performed in
order to establish the system contaminant level. Refer to Fluid Analysis Laboratory Guide,
SEBF3116, "Obtaining an Oil Sample for S·O·S Analysis". Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
1. Remove two hose assemblies (1) from the flow divider valve.
2. Remove sensor (4).
2/3(W)
w
2019/10/19

3. Remove two hose assemblies (5).
4. Attach a hoist and a lifting strap to the flow divider valve.
5. Remove seven bolts (2) that hold the flow divider valve onto the main control valve.
6. Remove flow divider valve (2). The weight of the flow divider valve is 64 kg (140 lb).
Sat Oct 19 15:32:55 UTC+0800 2019
3/3(W)
w
2019/10/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01981962
Flow Divider Valve - Disassemble
SMCS - 5097-015; 5137-015
Disassembly Procedure
Table 1
Required Tools
A 3E-6910 Bolts 2
Start By:
A. Remove the flow divider valve. Refer to Disassembly and Assembly, "Flow Divider Valve -
Remove" for the machine that is being serviced.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
1/15(W)
w
2019/10/19

Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1. Remove fittings (1) from valve housing (3). Remove pressure sensor (2) from the valve
housing.
2. Remove O-ring seal (4) from the fittings.
2/15(W)
w
2019/10/19

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

3. Remove O-ring seal (5) from the pressure sensor.
4. Remove plugs (6), (7), and (8) from the valve housing.
5. Remove O-ring seal (9) from plug (6) .
3/15(W)
w
2019/10/19

4/15(W)
w
2019/10/19

8. Remove bolts (12). Remove covers (13) from the valve housing. Remove cap (14) and
nipple (15) from the valve housing.
9. Remove O-ring seal (16) from the cover. Repeat for the other cover.
10. Remove O-ring seal (17) from the nipple.
5/15(W)
w
2019/10/19

11. Remove bolts (18). Remove solenoid (19) from the valve housing.
12. Remove O-ring seals (23), (22), (21), and (20) from the solenoid.
13. Remove plug (24) from the valve housing.
6/15(W)
w
2019/10/19

Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM00001 and up).pdf

Similar to Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM00001 and up).pdf (20)

More from s20y0196u

More from s20y0196u (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM00001 and up).pdf