JCB 535-67 TELESCOPIC HANDLER Service Repair Manual ALL:572775 Onwards

PUBLISHED BY THE TECHNICAL PUBLICATIONS DEPARTMENT OF
JCB SERVICE; © ROCESTER,STAFFORDSHIRE, ST14 5LS, ENGLAND
Tel. ROCESTER (01889) 590312 PRINTED IN ENGLAND
Publication No. 9803/3600
Service Manual
500 Series
From m/c No. 561001

Contents
9803/3600 Issue 8*
This Service Manual covers the following Machines:-
525-58 and 525-58 Farm Special - from machine Serial Number 561001
525-58 and 525-67 Farm Special Plus
525-58 and 525-67 Basic Servo Options
527-58 and 527-67 - from machine Serial Number 572775
530-95 - from machine Serial Number 564980
530-110 and 530-120 - PlaceAce
530-110 and 530-120 Servo Options
537-120 and 537-130 from machine Serial Number 572900
Information covers two stage and three stage boom machines.
General 1
Hydraulics 2
Body and Framework 3
PlaceAce Control System 4
Servo Control System 4A
Engine 5
Transmission 6
Axles 7
Brakes 8
Hydraulic Steering 9
Electrics 10
Service Tools 11
Index
*
Open front screen

Contents
9803/3600 Issue 2*
Introduction
This publication is designed for the benefit of JCB Distributor Service Engineers who are receiving, or have received, training
by JCB Technical Training Department.
It is assumed that these personnel have a sound knowledge of workshop practice, safety procedures, and general techniques
associated with the maintenance and repair of hydraulic earthmoving equipment. Therefore these basic subjects generally are
omitted from this manual, the intention being to convey only more specialised information concerning particular aspects of a
machine or component.
For example, renewal of oil seals, gaskets, etc., and any component showing obvious signs of wear or damage is expected as
a matter of course, and therefore information of this nature is included only in the context of specialised procedures or where a
range of wear tolerances is required. Similarly, it is expected that components will be cleaned and lubricated where
appropriate, also that any opened hose or pipe connections will be blanked to prevent excessive loss of hydraulic fluid and
ingress of dirt.
For convenience this manual is compiled in sections, e.g. "Hydraulics", "Electrics", etc. but, to find details of a specific
component, reference should be made to the alphabetical index at the back of the book.
Illustrations which show a dismantled component are numbered as a guide to the dismantling sequence, which generally can
be reversed for assembly.
Torque settings are given as a 'mean' figure which may be varied by plus or minus 3%. Torque figures indicated are for dry
threads, hence for lubricated threads may be reduced by one third. Where no figure is quoted in the text, refer to page 1/1 - 3.
'Left Hand' and 'Right Hand' are as viewed from the rear of the machine looking forward.
! WARNING
Asbestos
Asbestos dust can damage your lungs. Some engine joints
and gaskets may contain asbestos. Take the following
precautions when working on them.
1 Wear a face mask and gloves.
2 Work in a well ventilated area and do not smoke.
3 Do not use a rotary wire brush, use a hand scraper.
4 Make sure the material to be removed is wet with oil or
water to contain loose particles.
5 Place all material into plastic bags and dispose in
accordance with local regulations.
GEN-1-8
! WARNING
Fluoroelastomeric Materials
Certain seals and gaskets (e.g. crankshaft oil seal) on JCB
machines contain fluoroelastomeric materials such as Viton,
Fluorel and Technoflon. Fluoroelastomeric materials
subjected to high temperatures can produce highly corrosive
hydrofluoric acid. THIS ACID CAN SEVERELY BURN.
New fluoroelastomeric components at ambient temperature
require no special safety precautions.
Used fluoroelastomeric components whose temperatures
have not exceeded 300°C require no special safety
precautions. If evidence of decomposition (e.g. charring) is
found, refer to the next paragraph for safety instructions DO
NOT TOUCH COMPONENT OR SURROUNDING AREA.
Used fluoroelastomeric components subjected to
temperatures greater than 300°C (e.g. engine fire) must be
treated using the following safety procedure. Make sure that
heavy duty gloves and special safety glasses are worn:
1 Ensure that components have cooled then remove and
place material into plastic bags.
2 Thoroughly wash contaminated area with 10% calcium
hydroxide or other suitable alkali solution, if necessary
use wire wool to remove burnt remains.
3 Thoroughly wash contaminated area with detergent and
water.
4 Contain all removed material, gloves etc. used in this
operation in sealed plastic bags and dispose of in
accordance with Local Authority Regulations.
DO NOT BURN FLUOROELASTOMERIC MATERIALS.
If contamination of skin or eyes occurs, wash the affected
area with a continuous supply of clean water or with calcium
hydroxide solution for 15-60 minutes. Get medical attention
immediately.
INT-3-3-5/1

Colour Coding
The following colour coding, used on illustrations to denote various conditions of oil pressure and flow, is standardised
throughout JCB Service publications.
9803/3600 Issue 1
A390940
Full Pressure
Pressure generated from operation of a service. Depending on application this may
be anything between neutral circuit pressure and M.R.V. operating pressure.
Pressure
Pressure that is above neutral circuit pressure but lower than that denoted by red.
Servo
Oil pressure used in controlling a device (servo).
Neutral
Neutral circuit pressure.
Exhaust
Cavitation
Oil subjected to a partial vacuum due to a drop in pressure (cavitation).
Lock Up
Oil trapped within a chamber or line, preventing movement of components (lock up).
Red
Pink
Orange
Blue
Green
Light
Green
Yellow

General
Issue 3*
i
1
9803/3600E
1
i
Contents Page No.
Fluids, Lubricants, Capacities & Specifications
- 525-58/67, 527-58/67 & 530-95 1 - 1
- 530-110 1 - 2
- 530-120, 537-120 & 537-130 1 - 2A
- 525-58 Farm Special Plus 530-67 & 535-67 1 - 2B
- Torque Settings 1 - 3
- Identifing Your Machine 1 - 4
Service Schedules 2 - 1
Greasing
Pivot Pins
- 525-58/67, 527-58/67, 530-67 & 535-67 3 - 1
- 530-120 3 - 2
- 530-110 3 - 3
- 530-95 3 - 4
Front Axle 3 - 5
Rear Axle 3 - 6
Carriage Lock Pins 3 - 7
Boom Wear Pad Runways 3 - 8
Extension Ram Pivots
- 525-58/67, 527-58/67, 530-67/95 & 535-67 3 - 9
- 530-120 3 - 10
- 530-110 3 - 11
Oiling 3 - 12
Boom Safety Strut 4 - 1
*

1 - 1
1 General
9803/3600
1
1 - 1
Issue 7*
FLUIDS, LUBRICANTS, CAPACITIES AND SPECIFICATIONS
(525-58, 67, 527-58, 67, 530-95)
Note: New engines DO NOT require a running-in period. The engine/machine should be used in a normal work cycle
immediately; glazing of the piston cylinder bores, resulting in excessive oil consumption, could occur if the engine is gently run-
in. Under no circumstances should the engine be allowed to idle for extended periods; (e.g. warming up without load). Engines
of new machines are filled at the factory with JCB 10W/30 Multigrade oil. This oil should be drained after the first 100 hours
operation and the engine filled with the appropriate recommended grade as shown in the lubrication chart. JCB 10W/30
Multigrade should also be used for the first 100 hours operation whenever a new or reconditioned engine is fitted to the
machine. After the first 100 hours operation, it is essential that the 10W/30 oil is replaced by the lubricant recommended below.
ITEM CAPACITY FLUID/LUBRICANT INTERNATIONAL
Litres (Gal) SPECIFICATION
Fuel Tank 90 (20) Diesel Oil (See Types of Fuel) ASTM D975-66T Nos. 1D, 2D
Engine (Oil) 10 (2.2) JCB 15W/40 Multigrade SAE15W/40, MIL-L-46152B,
-10 °C to 50 °C (14 °F to 122 °F) API CD/SE, MIL-L-2104
JCB Super Universal Agricultural SAE10W/30, MIL-L-2105, MIL-L-46152
-15 °C to 30 °C (5 °F to 86 °F) API CD/SE, MIL-L-2104C
JCB Torque Converter Fluid SAE10W, MIL-L-46152, MIL-L-2104D
-18 °C to 0 °C (0 °F to 32 °F) API CD/SE
Engine (Coolant) 17 (3.7) JCB Universal Antifreeze/water ASTM D3306-74
( See Coolant Mixtures)
Gearbox
Syncro Shuttle 18.25 (4.0) JCB Special Transmission Fluid ESP-M2C 33G
Powershift †15.0 (3.3) JCB Special Transmission Fluid ESP-M2C 33G
Front Axle
Housing 18 (3.9) JCB Special Gear Oil ESEN-M2C 86A/B
Hubs (x2) 2.0 (0.4) JCB Special Gear Oil ESEN-M2C 86A/B
Rear Axle
Brake System JCB Light Hydraulic Fluid ISO VG15
DO NOT USE ORDINARY BRAKE FLUID
Hydraulic Tank *152 (33.5) JCB High Performance Hydraulic Oil ISO VG46
(Above 38 °C, 100 °F)
JCB Special Hydraulic Fluid ISO VG32
(Below 38 °C, 100 °F)
Grease Points JCB Special MPL Grease Lithium based, No. 2 consistency
Wear Pad Runways JCB Waxoyl
Boom Hoses JCB Special Slide Lubricant
* Note: This is nominal machine capacity. The total hydraulic system capacity depends on the equipment being used. Fill with
all rams closed. Watch level sight glass when filling.
† Note: This is a system capacity. Use the 'MIN' and 'MAX' marks on the dipstick when refilling the system.
Coolant Mixtures % Antifreeze Starts to Freeze
55 9.35 litres (2.04 gal) -36° C (-33 °F)
*
*

1 - 2
1 General
9803/3600
1
1 - 2
Issue 8*
machine. After the first 100 hours operation, it is essential that the 10W/30 oil is replaced by the lubricant recommended
below.
Engine (Oil)
Engine Type: 10 (2.2) JCB Super Multigrade 15W/40 SAE15W/40
AA, AB, AR & AK -10°C to 50°C (14°F to 122°F) API CF4/SG
Builds JCB Super Multigrade 10W/30 SAE 10W/30
-15°C to 40°C (5°F to 104°F) API CF4/SG
Engine Type: JCB Super Universal Agricultural SAE10W/30
AA & AB Builds -15°C to 30°C (5°F to 86°F) API CD/SE
Only JCB Torque Converter Fluid SAE10W
-18°C to 0°C (0°F to 32°F) API CD/SE
Engine (Coolant) JCB Four Seasons Antifreeze ASTM D3306-74
System 18 (3.9) And Summer Coolant
Antifreeze 10 (2.2) ( See Coolant Mixtures)
Axles
Housing (Front) 18 (3.9) JCB High Performance Gear Oil API GL4
Housing (Rear) 13 (2.8)
Hubs (x2) 2.0 (0.4)
Hydraulic Tank (*) 190 (41.8) JCB High Performance Hydraulic Oil ISO VG46
(Above 38°C, 100°F)
(Below 38 °C, 100 °F)
JCB Light Hydraulic Fluid ISO VG15
(For Iceland, Norway, Sweden
and Finland ONLY)
Grease Points (**) JCB HP Grease Lithium complex NLGI No. 2 consistency
including extreme pressure additives
JCB Special MPL-EP Grease Lithium based NLGI No. 2 consistency
including extreme pressure additives
(*) Note: This is nominal machine capacity. The total hydraulic system capacity depends on the equipment being used. Fill and
check with all rams closed. Watch level sight glass when filling.
(**) Note: If JCB MPL Grease is used, all 50 hour greasing operations must be carried out at TEN (10) HOUR intervals; all 500
hour greasing operations must be carried out at 50 HOUR intervals.
(530-110)

1 - 2A
1 General
9803/3600
1
1 - 2A
Issue 2*
below.
Engine (Coolant) 23.5 (5.2) JCB Universal Antifreeze/water ASTM D3306-74
Front Axle
Rear Axle
Hydraulic Tank †292 (64.3) JCB High Performance Hydraulic Oil ISO VG46
(Above 38 °C, 100 °F)
JCB HP32 ISO 32
(Below 38 °C, 100 °F)
† Note: This is nominal machine capacity. The total hydraulic system capacity depends on the equipment being used. Fill with
55 12.92 litres (2.84 gal) -36° C (-33 °F)
(530-120, 537-120 & 537-130)
*
*
*

1 - 2B
1 General
9803/3600
1
1 - 2B
Issue 3*
below.
Engine (Coolant) 17 (3.7) JCB Universal Antifreeze/water ASTM D3306-74
Gearbox
Powershift †15.0 (3.3) JCB Special Transmission Fluid ESP-M2C 33G
Front Axle
Rear Axle
Hydraulic Tank ††152 (34.5) JCB High Performance Hydraulic Oil ISO VG46
(Above 38 °C, 100 °F)
(Below 38 °C, 100 °F)
†† Note: This is nominal machine capacity. The total hydraulic system capacity depends on the equipment being used. Fill with
† Note: This is a system capacity. Use the 'MIN' and 'MAX' marks on the dipstick when refilling the system.
55 9.35 litres (2.04 gal) -36° C (-33 °F)
(525-58 Farm Special Plus, 530-67, 535-67)
*
*

1 - 3
1 General
9803/3600
1
1 - 3
Issue 2*
Torque Settings
Use only where no torque setting is specified in the text. Values are for dry threads and may be within three per cent of the
figures stated. For lubricated threads the values should be REDUCED by one third.
UNF Grade 'S' Bolts
Bolt Size Hexagon (A/F) Torque Settings
in (mm) in Nm kgf m lbf ft
1
/4 (6.3) 7
/16 14 1.4 10
5
/16 (7.9) 1
/2 28 2.8 20
3
/8 (9.5) 9
/16 49 5.0 36
7
/16 (11.1) 5
/8 78 8.0 58
1
/2 (12.7) 3
/4 117 12.0 87
9
/16 (14.3) 13
/16 170 17.3 125
5
/8 (15.9) 15
/16 238 24.3 175
3
/4 (19.0) 11
/8 407 41.5 300
7
/8 (22.2) 15
/16 650 66.3 480
1 (25.4) 11
/2 970 99.0 715
11
/4 (31.7) 17
/8 1940 198.0 1430
11
/2 (38.1) 21
/4 3390 345.0 2500
Metric Grade 8.8 Bolts
Bolt Size Hexagon (A/F) Torque Settings
(mm) mm Nm kgf m lbf ft
M5 (5) 8 7 0.7 5
M6 (6) 10 12 1.2 9
M8 (8) 13 28 3.0 21
M10 (10) 17 56 5.7 42
M12 (12) 19 98 10 72
M16 (16) 24 244 25 180
M20 (20) 30 476 48 352
M24 (24) 36 822 84 607
M30 (30) 46 1633 166 1205
M36 (36) 55 2854 291 2105
Rivet Nut Bolts/Screws
Bolt Size Torque Settings (for steel rivet nuts)
(mm) Nm kgf m lbf ft
M3 (3) 1.2 0.12 0.9
M4 (4) 3.0 0.3 2.0
M5 (5) 6.0 0.6 4.5
M6 (6) 10.0 1.0 7.5
M8 (8) 24.0 2.5 18.0
M10 (10) 48.0 4.9 35.5
M12 (12) 82.0 8.4 60.5
Note: All bolts used on JCB machines are high tensile and must not be replaced by bolts of a lesser tensile specification.
*

2 - 1
Daily Weekly Initial Monthly 6 Monthly Yearly 2 Yearly
Pre-start Cold Checks Operation 10 50 100 250 500 1000 2000
Service Points and Fluid Levels Hr Hr Hr Hr Hr Hr Hr
ENGINE
Engine Air Filter Pre-cleaner Clean ● ● ● ● ● ●
Coolant Level and Condition Check ● ● ● ● ● ●
Fuel System For Leaks and Contamination Check ●
Oil Level and Condition Check ● ● ● ● ● ● ●
Fuel Filter Drain ● ● ● ● ●
Fuel Sedimenter Drain and Clean ● ● ● ● ● ●
Air Cleaner Dust Valve Clean ● ● ● ● ●
Oil and Filter Change ● ● ● ●
Fuel Lift Pump Clean ● ● ● ●
Engine Mounting Bolts Check ● ● ● ●
Fuel Filter Change ● ● ● ●
Air Cleaner Outer Element Change ● ● ●
Valve Clearance Check ●
Air Cleaner Inner Element Change ●
Fan Belt Tension/Condition Check ● ● ● ●
Engine Exhaust for Security Check ● ● ● ●
Air Inlet for Security Check ● ● ● ●
Radiator Clean ● ● ●
All hoses Condition ● ● ● ● ●
TRANSMISSION AND AXLES
Transmission Oil Level Check ● ● ● ● ● ● ●
Tyre Pressures and Condition (see Handbook) Check ● ● ● ● ● ● ●
Tightness of Wheel Nuts Check ● ● ● ● ● ● ●
Axle(s) Oil Level Check ● ● ● ● ●
Axle(s) Oil Change ● ● ●
Hub Oil Levels Check ● ● ● ● ●
Hub Oil Change ● ● ●
Drive Shafts and Universal Joints Grease ● ● ● ● ● ●
Steer Axle Pivots and Linkages Grease ● ● ● ● ● ●
Wheel Alignment (see Handbook) Check ● ● ● ● ● ● ●
Wheel Bearings Check and Adjust ● ● ●
King Pin and Bushes Check and Adjust ● ● ●
Transmission Oil Filter Change ● ● ● ●
Transmission Oil Change ● ●
Transmission Strainer Clean ● ●
Axle Breathers Check Clear ●
Axle Security Check ●
Transmission Mount Security Check ●
Steering Stops (if fitted) ●
HYDRAULICS
Hydraulic Fluid Level Check ● ● ● ● ● ● ●
System for Leaks Check ● ● ● ● ● ●
Oil Filter Change ● ● ● ● ●
Oil (and clean suction strainers) Sample/Change ●
1 General
9803/3600
1
2 - 1
Issue 5*
*
*
*
*

2 - 2
Pre-start Cold Checks Operation 10 50 100 250 500 1000 2000
Service Points and Fluid Levels Hr Hr Hr Hr Hr Hr Hr
BRAKES
Fluid Level Check ● ● ● ● ● ● ●
Parking Brake Cable Lubricate ● ● ● ● ●
Brake System Fluid Change ●
ELECTRICS
Alternator Drive Belt Tension Check ● ● ● ●
Battery Terminals for Condition and Tightness Check ● ● ● ● ●
Wiring Harness for Chafing Check ● ●
Battery Electrolyte Level and Condition Check ● ● ● ●
Starter Motor and Alternator Check ● ●
Battery Charge Condition Check ●
BODY AND FRAMEWORK
All Pivot Pins Grease ● ● ● ● ● ●
Control Lever Linkages Lubricate ● ● ● ● ● ●
All Hinges Lubricate ● ● ● ● ●
Wear Pad Runways Waxoyl ● ● ●
Inner Boom Hoses Grease ● ● ●
Boom Extension Ram Pivot Check and Grease ● ●
Boom Wear Pad (Machines from S/No. 561001) Check ● ● ● ●
Inner Extension Ram Wear Pad (530-95/110) Replace ● ●
Wear Pad Condition Check ●
CAB
Windscreen Washer Fluid Level Fill ● ● ● ● ● ● ●
Seat Belt/Seat Security and Condition Check ● ● ● ● ● ● ●
Fire Extinguisher Check ● ● ● ● ● ●
Cab Heater Filter (if fitted) Clean ● ● ●
Wing Mirrors Condition and Security Check ● ● ● ● ● ●
ROPS/FOPS Structure Check ● ● ● ●
ATTACHMENTS
Carriage Lock Pins Grease ● ● ● ● ●
Fork Pivot Pins Grease ● ● ●
Optional Attachments (as required) Grease
Forks Fit and Check Security ●
1 General
9803/3600
1
2 - 2
Issue 7*
*
*
*

2 - 3
Functional Test Operation 10 50 100 250 500 1000 2000
and Final Inspection Hr Hr Hr Hr Hr Hr Hr
ENGINE
Exhaust Smoke Check ● ● ● ● ● ● ●
Idle Speed Check and Adjust ● ● ● ●
Max Governed Speed Check and Adjust ● ● ● ●
Torque Converter Stall Speed Check ● ● ● ●
Max No Load Speed Check ● ● ● ●
Throttle System and Control Cable Check ●
Operation of Stop Control/E.S.O.S. Check ●
Coolant System for Leaks Check ●
Engine for Vibration/Noise Check ● ● ● ● ●
TRANSMISSION AND AXLES
Transmission Operation Check ● ● ● ● ● ●
Clutch Pack Pressures Check ● ● ● ●
Torque Converter Mainline Pressure ● ● ●
Clutch Disconnect/Dump Pedal/Switch Check ●
Gear Change and Selection Check ●
2WD/4WD Selection (if fitted) Check ●
Forward/Reverse Selection/Operation Check ● ● ● ●
Neutral Start Operation Check ● ● ● ●
Reverse Alarm Operation Check ● ● ● ● ● ● ●
Oil Cooler and Pipework Check ●
HYDRAULICS
Operation of All Services Check ● ● ● ● ● ● ●
Steering Operation Check ● ● ● ● ● ●
Main Relief Valve Setting Check and Adjust ● ● ● ●
Auxiliary Relief Valve Setting Check and Adjust ● ● ● ●
Hose Burst Protection Valves Check ● ● ● ● ● ● ●
Steer Relief Valve Setting Check and Adjust ● ● ●
Fan Motor Speed Check and Adjust ● ● ●
Cooling Pump MRV Pressure Check and Adjust ●
Steer Circuit MRV Pressure Check and Adjust ● ● ● ●
Operation of Cooling Fan Motor Check ●
Servo Remote Operation Check ●
Hoses/Pipework for Damage or Leaks Check ● ● ● ● ●
Piston Rods and Gland Seals Check ● ● ● ● ●
Boom Extension Phasing Check ●
Parallel Lift/Lower Check ●
Stabiliser Leg Cut-Out Check ●
Sway Control Check ●
Main Hydraulic Pump Mounting Check ●
Load Hold Check Valve Check Operation ●
BRAKES
Foot Brake Operation and Balance Check ● ● ● ● ● ● ●
Parking Brake Operation Check and Adjust ● ● ● ● ● ●
Servo Operation (if fitted) Check ● ● ● ●
1 General
9803/3600
1
2 - 3
Issue 8*
*
*

2 - 4
Functional Test Operation 10 50 100 250 500 1000 2000
and Final Inspection Hr Hr Hr Hr Hr Hr Hr
ELECTRICS
Instrument Readings Check ● ● ● ● ● ● ●
Warning Lights and Audible Alarm Check ● ● ● ● ● ● ●
Operation of All Electrical Equipment Check ● ● ● ● ● ●
Operation of Safe Load Indicator Check ● ● ● ● ● ●
Heater Operation Check ●
Steer Mode Selection Check ● ● ● ●
Steering Alignment Check ● ● ● ● ● ● ●
Stabiliser Indication Check ●
Starter Motor Check ● ●
Alternator Check ● ●
Cab Switches Check ● ● ●
Proximity Sensors Check Function ● ● ●
Wiper Motor(s) Check ● ● ●
Safe Load Indicator Calibrate ● ● ●
BODY AND FRAMEWORK
Boom Wear Pad Security Check ●
Inclinometer Operation and Security Check ●
CAB
Glazing for Correct Fit Check ●
Tool Kit and Handbook Check ●
Doors and Hinges Check ●
Locks and Keys Check ●
PAINTWORK
Condition Check ●
ATTACHMENTS
Operation Check ●
Circuit Pressures Check ● ● ● ●
Optional Equipment (as fitted) Check ● ● ●
1 General
9803/3600
1
2 - 4
Issue 2*
*

3 - 2
1 General
9803/3600
1
3 - 2
Issue 7*
GREASING (See Section Contents for machine models)
For interval see Service Schedule
*
S146620

3 - 3
1 General
9803/3600
1
3 - 3
Issue 7*
*
S138700

3 - 4
1 General
9803/3600
1
3 - 4
Issue 6*
*
S155800

3 - 5
GREASING
Front Axle and Driveshaft
Note: Raise the wheels and swing them from lock to lock.
This will ensure full penetration.
All except 530-120
530-120 only
! WARNING
Make the machine safe before working underneath it.
Park the machine on level ground, lower the boom.
Apply the parking brake, put the transmission in neutral
and stop the engine. Chock both sides of all four wheels.
Disconnect the battery, to prevent the engine being
started while you are beneath the machine.
GEN-003
1 General
9803/3600
1
3 - 5
Issue 6*
4
0
1
2
8
3 5
6
7
9
!
£
1
2
9
4
3 5
6 8
7
0 !
@
S138690
*
*

3 - 6
GREASING
Rear Axle and Driveshaft
Note: Raise the wheels and swing them from lock to lock.
This will ensure full penetration.
All except 530-120
530-120 only
! WARNING
Park the machine on level ground, lower the boom.
Apply the parking brake, put the transmission in neutral
and stop the engine. Chock both sides of all four wheels.
GEN-003
1 General
9803/3600
1
3 - 6
Issue 4*
2
4
9
5
7
1
3
6
8
!
0
*
*

GREASING
Carriage Lock Pins - Grease Every 50 Hours
2 Grease Points
Fork Pivot Pins - Grease Every 250 Hours
1 General
9803/3600
1
Issue 1
3 - 7 3 - 7
138710

GREASING
Boom Wear Pad Runways - Every 1000 Hours
Remove boom rear cover. With the boom retracted apply Waxoyl to the inner, intermediate and outer boom inner surfaces.
Extend the boom to uncover the inner surfaces as required, refit the boom rear cover.
With the boom fully extended apply Waxoyl evenly over surfaces A. Allow 2-3 hours drying time before retracting the boom.
Apply Slide lubricant to inner hoses and hose runs.
The illustration shown is a 3 stage boom but the procedure applies to all machines.
3 - 8
1 General
9803/3600
1
3 - 8
Issue 2*
! CAUTION
Waxoyl contains turpentine
substitute, which is flammable. Keep
flames away when applying Waxoyl.
Waxoyl can take a few weeks to dry
completely. Keep flames away
during the drying period.
Do not weld near the affected area
during the drying period. Take the
same precautions as for oil to keep
Waxoyl off your skin. Do not breathe
the fumes. Apply in a well-ventilated
area.
5-3-1-9
*
S138730

3 - 9
1 General
9803/3600
1
3 - 9
Issue 2*
Boom Extension Ram Pivots - Every 1000 Hours
Remove inner extension ram pivot pin A and coat with specified grease. Refit pivot pin.
Note: Use another pivot pin to support the ram while greasing the pivot pin.
A
S112050
*

3 - 10
1 General
9803/3600
1
3 - 10
Issue 2*
S138740
*
A
1
2
3

3 - 11
1 General
9803/3600
1
3 - 11
Issue 2*
S143500
*
A
1
32

3 - 12
1 General
9803/3600
1
3 - 12
Issue 2
OILING
The following points should be lightly oiled with engine oil at
the periods stated in the service schedule.
! WARNING
Park the machine on level ground, lower the boom. Apply
the parking brake, put the transmission in neutral and
stop the engine. Chock both sides of all four wheels.
GEN-003
1 Parking Brake Cable
Oil the clevis at the brake end of the cable. DO NOT
allow oil to get on to the brake disc.
2 2/4 Wheel Drive Lever (if fitted)
Oil the clevis at the end of the lever.
3 Control Levers (Not PlaceAce or Servo Machines)
Oil the clevis at the bottom of each control lever.
S112070
S112070
S112070

4 - 1
FITTING THE BOOM SAFETY STRUT
! WARNING
You could be killed or injured if the boom drops while
you are working under it.
Always fit the boom safety strut before working
underneath a raised boom.
GEN-004
Fit the boom safety strut as follows:
1 Raise the boom just far enough to fit the strut then stop
the engine.
2 Remove the strut from its stowage position and place
around the ram piston rod as shown. Fix in place with
screw A.
3 Start the engine lower the boom carefully onto the strut.
Stop as soon as the weight of the boom is on the strut.
Remove the boom safety strut as follows:
1 Raise the boom slightly to clear the strut then stop the
engine.
2 Remove screw A and remove the strut from the ram.
3 Secure the strut in its stowage position.
1 General
9803/3600
1
4 - 1
Issue 1
S138640
A

2
i
Hydraulics
Issue 4*9803/3600E
Contents Page No.
Technical Data
- 525-58/67, 527-58/67, 530-67 & 535-67 1 - 1
- 530-120 1 - 1A
- 530-110 1 - 1B
- 530-95 1 - 1C
- 537-120 1 - 1D
- 537-130 1 - 1E
General Description 1 - 2
Hydraulic Fluid Level & Filter
- All except 530-120, 537-120/130 2 - 1
- 530-120, 537-120/130 2 - 1A
Draining Fluid & Cleaning Suction Strainers 2 - 2
Hydraulic Tank Removal & Replacement
- All except 530-120, 537-120/130 2 - 3
- 530-120, 537-120/130 2 - 5
Pump Operation 3 - 1
Pump Removal & Replacement
- All except 530-120, 537-120/130 3 - 3
- 530-120 up to serial No. 569293 3 - 5
- 530-120 from serial No. 569294 & 537-120/130 3 - 6
Pump Dismantle & Assembly
- 530-120, 537-120/130 up to serial No. 577458 3 - 7
- 530-120, 537-120/130 from serial No. 577459 3 - 8A
Supplementary Pump (Farm Special Plus, 530-67, 535-67)
- Removal & Replacement 3 - 9
- Dismantle & Assembly 3 - 11
Machine Neutral Circuit (without torsion box cooling) 4 - 1
Machine Neutral Circuit (with torsion box cooling) 4 - 2A
Machine Neutral Circuit (with filter in steer circuit) 4 - 2C
Machine Neutral Circuit (with supplementary pump) 4 - 2E
Machine Neutral Circuit (with priority steer/fan pump) 4 - 2G
Control Valve Block Neutral Circuit 4 - 3
Boom Lift Operation (525-67, 527-67, 530-67, & 535-67) 4 - 5
Boom Lower Operation (525-67, 527-67, 530-67, & 535-67) 4 - 7
Boom Lift Operation (525-58, 527-58) 4 - 9
Boom Lower Operation (525-58, 527-58) 4 - 11
Hose Burst Operation 4 - 13
Boom Extend/Retract Operation
(525-58/67, 527-58/67 530-67, 535-67, 530-95) 4 - 15
Sway Operation 4 - 17
Boom Lift Operation (530-110/120, 537-120/130) 4 - 19
Boom Lower Operation (530-110/120, 537-120/130) 4 - 21
Boom Extend Regenerative (530-110/120, 537-120/130) 4 - 23
Boom Extend High Pressure (530-110/120, 537-120/130) 4 - 25
Boom Retract (530-110/120, 537-120/130) 4 - 27
Stabiliser Check Valve Operation 4 - 29
Stabiliser Operation 4 - 31
M.R.V. Operation 4 - 33
A.R.V. Operation 4 - 34
i
2
*

ii
2 Hydraulics
9803/3600E
2
ii
Issue 4*
Contents Page No.
Control Valve Block Removal & Replacement 5 - 1
Control Valve Block Dismantle & Assembly 5 - 3
Dual Function Controls Assembly 5 - 5
Pressure Testing 6 - 1
Lift Rams Removal & Replacement 7 - 1
Displacement Rams Removal & Replacement 7 - 3
Extension Ram Removal & Replacement (525-58, 527-58) 7 - 5
Extension Ram Removal & Replacement
- (525-67,527-58, 530-67 & 535-67) 7 - 7
Tilt Ram Removal & Replacement 7 - 9
Sway Ram Removal & Replacement 7 - 11
Tow Hitch Ram Removal & Replacement 7 - 13
Inner Extension Ram Removal & Replacement
- (530-110/120, 537-120/130) 7 - 15
Outer Extension Ram Removal & Replacement
- (530-110/120, 537-120/130) 7 - 17
Boom Extension Circuit Bleeding Procedure
- (530-110/120, 530-120/130) 7 - 19
Extension Ram Make Up Valve
- (530-110/120, 537-120/130) 7 - 20
Boom Hoses Removal & Replacement (530-95) 7 - 21
Boom Hoses Chain Track
- Removal & Replacement (530-95) 7 - 23
Extension Ram Removal & Replacement (530-95) 7 - 25
Stabiliser Ram Removal & Replacement 7 - 27
Diverter Valve Removal & Replacement 7 - 29
Diverter Valve Dismantle & Assembly 7 - 30
Typical Ram Dismantle & Assembly 8 - 1
Tow Hitch Ram Dismantle & Assembly 8 - 3
Typical Ram with Dowel Head Dismantle & Assembly 8 - 5
Fan Motor Removal, Replacement & Adjustment 9 - 1
Fan Motor (Sundstrand) Dismantle & Assembly 9 - 3
Fan Motor (Ultra) Dismantle & Assembly 9 - 5
Schematic Hydraulic Circuit
- 525-58/67, 527-58/67 & 530-95 up to machine s/n 567217 10 - 1
- 525-58/67, 527-58/67 & 530-95 from machine s/n 567218 10 - 3
- 527-58/67, 535-67 from machine s/n 574296 10 - 4A
- All 530-120 & 530-110 up to machine s/n 567217 10 - 5
- 530-110 from machine s/n 567218 10 - 7
- 530-67 & 535-67 10 - 9
- 537-120/130 10 - 11

1 - 1
2 Hydraulics
9803/3600E
2
1 - 1
Issue 9*
TECHNICAL DATA (525-58, 67, 527-58, 67, 530-67 & 535-67)
Pump
Type Sundstrand SP/230/40, gear type
Flow at max. engine rev/min
— at zero pressure 88.0 litres/min 19.4 UK gal/min 23.2 US gal/min
— at system pressure 84.0 litres/min 18.5 UK gal/min 22.2 US gal/min
Supplementary Pump (Farm Special Plus & 530-67, 535-67)
Type Ultra IPR/009/CT/DT/BE/8451
Control Valves
Type Kontak, parallel service, double acting spools.
Services Operated
— Spool 1 Boom Raise & Lower
— Spool 2 Boom Extend & Retract
— Spool 3 Auxiliary (see note)
— Spool 4 Carriage Tilt
Relief Valve Operating Pressures bar kgf/cm2
lbf/in2
Main Relief Valve (MRV) 220 224 3200
Auxiliary Relief Valves (ARV)
— Attachments 138 140 2000
— Carriage Tilt, head side 138 140 2000
— Carriage Tilt, rod side 275 281 4000
— Hydraulic Tow Hitch lower (head side) 96 98 1400
— Hydraulic Tow Hitch raise (rod side) 172 176 2500
— Sway, head side 131 133 1900
— Sway, rod side 165 168 2400
Note: On later machines the sway ARVs are not fitted
Rams Bore Rod Dia. Stroke
mm in mm in mm in
Boom Lift - 525-58, 527-58 110 4.3 60 2.4 615 24.2
Boom Lift - 525-67, 527-58, 530-67, 535-67 110 4.3 60 2.4 807 31.8
Boom Extension - 525-58, 527-58 70 2.8 50 1.9 1700 66.9
Boom Extension - 525-67, 527-58, 530-67, 535-67 70 2.8 50 1.9 1968 77.5
Tilt Ram 110 4.3 50 1.9 620 24.4
Displacement 110 4.3 50 1.9 355 13.9
Tow Hitch 70 2.8 30 1.2 220 8.7
Sway Ram 110 4.3 50 1.9 196 7.7
Sway Ram (later machines) 110 4.3 50 1.9 178 7.0
Filter
Filter Type Partial flow ('spin on')
Filtration Size 25 microns (0.001 in)
Relief Valve Setting 0.17 bar
Suction Strainer 125 microns (0.005 in)
Fan Motor
Type Sundstrand TFU 200/8, gear type / Ultra 1MR 084C 8784
Max fan speed at Max engine rev/min 18 inch fan 20 inch fan
40° C ambient 46° C ambient 40° C ambient 46° C ambient
temp. zone temp. zone temp. zone temp. zone
NAT ASP engine 2100 2500
TURBO engine 2100 2100 2300 2600
Note: The function of spools 3, 5 & 6 (where fitted) will vary from machine to machine but may include the following: Hydraulic
Tow Hitch, Sway Control and Auxiliary Attachment Control.
*
*
*
*
*
*

1 - 1A
2 Hydraulics
9803/3600E
2
1 - 1A
Issue 5*
TECHNICAL DATA (530-120 Only)
Pump
Type Sundstrand SP/230/50 or Ultra 2PR050, gear type
Control Valves
Services Operated
— Spool 3 Auxiliary
— Spool 5 Stabiliser
— Spool 7 Sway
lbf/in2
Main Relief Valve (M.R.V.) 241 245 3500
Auxiliary Relief Valves (A.R.V.)
— Sway, rod side 165 168 2400
mm in mm in mm in
Boom Lift 120 4.7 65 2.5 1040 40.9
Boom Outer Extension 120 4.7 65 2.5 3053 120.1
Boom Inner Extension 100 3.9 60 2.3 3107 122.3
Tilt Ram 130 5.1 50 1.9 695 27.3
Displacement 130 5.1 50 1.9 500 19.6
Stabiliser 110 4.3 60 2.3 527 20.7
Sway 110 4.3 50 1.9 196 7.7
On machines from serial number 567736
Tilt Ram 130 5.1 65 2.5 695 27.3
Displacement 130 5.1 65 2.5 500 19.6
Filter
Fan Motor
Type Sundstrand TFU 200/8, gear type or Ultra 1MR 084C 8784
Max fan speed at Max engine rev/min 40° C ambient 46° C ambient
temp. zone temp. zone
TURBO engine 1800 2500
*

1 - 1B
2 Hydraulics
9803/3600E
2
1 - 1B
Issue 3*
Pump
Control Valves
Services Operated
— Spool 3 Auxiliary
lbf/in2
Rams Bore Rod Dia Stroke
mm in mm in mm in
Boom Lift 110 4.3 60 2.3 1020 40.1
Boom Outer Extension 110 4.3 60 2.3 2560 100.7
Boom Inner Extension 90 3.5 60 2.3 2690 105.9
Tilt Ram 120 4.7 65 2.5 495 19.4
Displacement 120 4.7 65 2.5 495 19.4
Stabiliser 100 3.9 60 2.3 380 15
Filter
Fan Motor

1 - 1C
2 Hydraulics
9803/3600E
2
1 - 1C
Issue 3*
Pump
Control Valves
Services Operated
— Spool 6 Sway
lbf/in2
— Sway, rod side 165 168 2400
mm in mm in mm in
Boom Lift 110 4.3 60 2.3 1020 40.1
Boom Extension 100 3.9 60 2.3 3860 151.9
Tilt Ram 120 4.7 65 2.5 495 19.4
Displacement 120 4.7 65 2.5 495 19.4
Sway 110 4.3 60 1.9 196 7.7
Filter
Fan Motor
Note: The function of spools 3, 5 (where fitted) will vary from machine to machine but may include the following: Hydraulic Tow
Hitch, and Auxiliary Attachment Control.

Thank you very much
for your reading.
Please Click Here
Then Get More
Information.

JCB 535-67 TELESCOPIC HANDLER Service Repair Manual ALL:572775 Onwards

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Recently uploaded

Recently uploaded (20)

JCB 535-67 TELESCOPIC HANDLER Service Repair Manual ALL:572775 Onwards