The document provides assembly instructions for installing a final drive and travel motor on a 304E Mini Hydraulic Excavator. It outlines 30 steps to assemble components such as seals, bearings, gears, springs, and housing parts. Proper torque specifications are listed for tightening nuts and bolts. Safety warnings are included to prevent injury from spring loaded parts during assembly.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...jfjksekkmsemm
The document provides assembly instructions for a final drive and travel motor for a 304E Mini Hydraulic Excavator. It outlines 30 steps to assemble various components like seals, bearings, gears, pistons, springs and covers. Proper torque values are specified for tightening bolts and nuts. Safety warnings are included to prevent injury from improper assembly of spring loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...ujfjjkjskkemme
The document provides instructions for assembling the final drive and travel motor of a 304E Mini Hydraulic Excavator. It lists 30 steps that include installing bearings, seals, gears, springs, and other components. Tools required include retaining ring pliers, spanner wrenches, and a duo-cone seal installation group. Safety warnings are provided to follow proper procedures when handling spring-loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...ufjsjjkksemme
The document provides assembly instructions for a final drive and travel motor. It describes 30 steps to assemble various components like seals, bearings, gears, pistons, springs, and plates. Tools including retaining ring pliers and spanner wrenches are required. Proper torque values are specified for tightening bolts, nuts and plugs. Cautions are provided about potential injury when assembling spring loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...hhjsekmdmm
The document provides assembly instructions for a final drive and travel motor for a 304E Mini Hydraulic Excavator. It outlines 30 steps to assemble various components like seals, bearings, gears, pistons, springs and covers. Proper torque values are specified for tightening bolts and nuts. Safety warnings are included to prevent injury from improper assembly of spring loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...fusjfjskekmem
The document provides assembly instructions for a final drive and travel motor. It describes 30 steps to assemble various components such as seals, bearings, gears, pistons, springs, and plates. Tools including retaining ring pliers and spanner wrenches are required. Proper torque specifications are listed for tightening bolts and plugs. Cautions are provided about potential injury when assembling spring-loaded parts.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RKY) Service Repair M...fujskkmdmdm
1. The document provides installation and removal procedures for the swing motor, swing drive, and hydraulic tank of a 303.5E Mini Hydraulic Excavator.
2. The swing motor and swing drive installation involves attaching lifting devices, applying anti-seize compound, and connecting hose assemblies.
3. The hydraulic tank removal requires disconnecting hoses and tubes, and removing bolts, while the installation involves connecting hoses and tubes and installing bolts.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...fidkdkdmdm
1. The document provides installation and removal procedures for a hydraulic tank on a 303.5E Mini Hydraulic Excavator.
2. It describes disconnecting hoses, removing bolts, and lifting the tank off the excavator using lifting brackets.
3. The installation procedure reverses the removal steps, reconnecting hoses and installing bolts to secure the tank.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...udfjjdfjkksekm
The document provides instructions for installing the hydraulic tank on a 303.5E Mini Hydraulic Excavator. It describes removing hoses and disconnecting lines from the tank. Lifting devices are needed to handle the 68 kg tank. Bolts must be installed and hoses reconnected to mount the tank on the excavator.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...jfjksekkmsemm
The document provides assembly instructions for a final drive and travel motor for a 304E Mini Hydraulic Excavator. It outlines 30 steps to assemble various components like seals, bearings, gears, pistons, springs and covers. Proper torque values are specified for tightening bolts and nuts. Safety warnings are included to prevent injury from improper assembly of spring loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...ujfjjkjskkemme
The document provides instructions for assembling the final drive and travel motor of a 304E Mini Hydraulic Excavator. It lists 30 steps that include installing bearings, seals, gears, springs, and other components. Tools required include retaining ring pliers, spanner wrenches, and a duo-cone seal installation group. Safety warnings are provided to follow proper procedures when handling spring-loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...ufjsjjkksemme
The document provides assembly instructions for a final drive and travel motor. It describes 30 steps to assemble various components like seals, bearings, gears, pistons, springs, and plates. Tools including retaining ring pliers and spanner wrenches are required. Proper torque values are specified for tightening bolts, nuts and plugs. Cautions are provided about potential injury when assembling spring loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...hhjsekmdmm
The document provides assembly instructions for a final drive and travel motor for a 304E Mini Hydraulic Excavator. It outlines 30 steps to assemble various components like seals, bearings, gears, pistons, springs and covers. Proper torque values are specified for tightening bolts and nuts. Safety warnings are included to prevent injury from improper assembly of spring loaded parts.
Caterpillar cat 304 e mini hydraulic excavator (prefix ssc) service repair ma...fusjfjskekmem
The document provides assembly instructions for a final drive and travel motor. It describes 30 steps to assemble various components such as seals, bearings, gears, pistons, springs, and plates. Tools including retaining ring pliers and spanner wrenches are required. Proper torque specifications are listed for tightening bolts and plugs. Cautions are provided about potential injury when assembling spring-loaded parts.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RKY) Service Repair M...fujskkmdmdm
1. The document provides installation and removal procedures for the swing motor, swing drive, and hydraulic tank of a 303.5E Mini Hydraulic Excavator.
2. The swing motor and swing drive installation involves attaching lifting devices, applying anti-seize compound, and connecting hose assemblies.
3. The hydraulic tank removal requires disconnecting hoses and tubes, and removing bolts, while the installation involves connecting hoses and tubes and installing bolts.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...fidkdkdmdm
1. The document provides installation and removal procedures for a hydraulic tank on a 303.5E Mini Hydraulic Excavator.
2. It describes disconnecting hoses, removing bolts, and lifting the tank off the excavator using lifting brackets.
3. The installation procedure reverses the removal steps, reconnecting hoses and installing bolts to secure the tank.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...udfjjdfjkksekm
The document provides instructions for installing the hydraulic tank on a 303.5E Mini Hydraulic Excavator. It describes removing hoses and disconnecting lines from the tank. Lifting devices are needed to handle the 68 kg tank. Bolts must be installed and hoses reconnected to mount the tank on the excavator.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...xie25190
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about spring loaded parts that could cause injury if not properly handled.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...s20y0196u
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists 31 steps for disassembly, removing components like valves, springs, seals, check valves, gears and bearings. It then lists 26 steps for assembly, installing these components in reverse order and noting precautions for parts under spring force. Tools required include bearing pullers, retaining ring pliers and a press.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...jiduanbu
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about parts that are spring loaded.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...iphg8793466
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about parts that are spring loaded.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...shenjiao97221
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about spring loaded parts that could cause injury if not properly handled.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...yhhjjkfkseme
The document provides instructions for installing a hydraulic tank on a 303.5E Mini Hydraulic Excavator. The procedure involves 21 steps, including attaching lifting devices to the tank, installing it on the excavator, and reconnecting all hydraulic hoses and lines. Proper cleanliness and identification of all components is emphasized to prevent contamination of the hydraulic system.
This document provides instructions for assembling the final drive of an excavator model 329D L. It lists the required tools and parts. The procedure involves installing bearings in the main housing and motor housing using a press to apply the proper preload. Shims are used to take up any clearance between the housings. Duo-Cone seals are installed in the housings using a special tool. Cleanliness is emphasized throughout the assembly process.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 428 SERIES II BACKHOE LOADER (Prefix 6TC) Service Repair Manu...jkdkkdsmmd
The document provides instructions for disassembling and assembling the rear axle group and differential of a 428 Series II Backhoe Loader. It describes removing and installing the rear axle group which involves disconnecting linkages, brackets, and mounting hardware. Steps are provided to disassemble the rear axle group into individual components like housing, gears, and brakes. The differential is also disassembled by removing case halves, bearings, gears, and other parts. Precise assembly steps list installing components in reverse order and include details like torque specifications.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before separating assembly components.
3. Reassembling the spring assembly in the tooling bench and using hydraulic force to compress the spring into position, requiring several tons of force. Proper centering and leveling of the assembly is critical.
This document provides the installation procedure for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. It also describes attaching lifting brackets and removing the lifting equipment once installation is complete.
The document is a service repair manual that provides step-by-step instructions for disassembling the final drive components of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, carrier assembly, planetary gears, and separating the sprocket housing from the motor housing. Detailed illustrations accompany each step to show how to remove individual parts like seals, shafts, and bearings from within the final drive assembly. Special tools are listed that may be required for tasks like removing retaining rings.
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into a motor housing in the correct order.
3. Attaching lifting devices and link brackets to install the assembled swing motor and remove the swing drive, which each weigh over 500 lbs.
This document provides instructions for removing and installing a swing motor on an excavator model 329D2 L. The removal procedure involves draining oil from the swing drive, using tools to remove bolts securing the swing drive, and using lifting equipment to remove the swing motor due to its weight of approximately 77 kg. The installation procedure outlines connecting harness assemblies, hoses, and tightening connections to specified torques.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix BFC) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling and assembling the transmission of a 329D L and 329D LN excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 36 steps for assembly, reinstalling these components in reverse order and noting cleaning requirements. Precise measurements are taken to determine the correct shim thickness for preloading bearings during assembly.
This document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. The disassembly process involves removing 27 components from the travel motor body and head. The assembly process reverses the disassembly steps and cautions that all components must be reinstalled in their original positions and orientations. Proper cleaning of components before and after disassembly and assembly is emphasized to prevent contamination of the hydraulic system.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant and outlines procedures for preparing the machine, removing and installing components like lines, the compressor, and performing functions like evacuating and charging the system. Personal protective equipment is required as the system is pressurized and contains refrigerant that can cause injury.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator. It begins with an overview of the required tools. The removal procedure involves disconnecting tubes and cables, removing clips and pins, and taking off bolts. The installation procedure specifies cleaning and lubricating parts, replacing seals, and using tools to install clips, pins and bolts in the reverse order of removal. Precautions are given to keep parts clean and check adjustments after installation.
More Related Content
Similar to Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix SSC) Service Repair Manual Instant Download.pdf
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...xie25190
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about spring loaded parts that could cause injury if not properly handled.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...s20y0196u
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists 31 steps for disassembly, removing components like valves, springs, seals, check valves, gears and bearings. It then lists 26 steps for assembly, installing these components in reverse order and noting precautions for parts under spring force. Tools required include bearing pullers, retaining ring pliers and a press.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...jiduanbu
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about parts that are spring loaded.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...iphg8793466
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about parts that are spring loaded.
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...shenjiao97221
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists the required tools and presents 31 steps for disassembly and 28 steps for assembly. The steps include removing and installing various components such as bolts, valves, springs, pistons, bearings, gears, seals, and plates. Cautions are provided about spring loaded parts that could cause injury if not properly handled.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...yhhjjkfkseme
The document provides instructions for installing a hydraulic tank on a 303.5E Mini Hydraulic Excavator. The procedure involves 21 steps, including attaching lifting devices to the tank, installing it on the excavator, and reconnecting all hydraulic hoses and lines. Proper cleanliness and identification of all components is emphasized to prevent contamination of the hydraulic system.
Similar to Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix SSC) Service Repair Manual Instant Download.pdf (6)
This document provides instructions for assembling the final drive of an excavator model 329D L. It lists the required tools and parts. The procedure involves installing bearings in the main housing and motor housing using a press to apply the proper preload. Shims are used to take up any clearance between the housings. Duo-Cone seals are installed in the housings using a special tool. Cleanliness is emphasized throughout the assembly process.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 428 SERIES II BACKHOE LOADER (Prefix 6TC) Service Repair Manu...jkdkkdsmmd
The document provides instructions for disassembling and assembling the rear axle group and differential of a 428 Series II Backhoe Loader. It describes removing and installing the rear axle group which involves disconnecting linkages, brackets, and mounting hardware. Steps are provided to disassemble the rear axle group into individual components like housing, gears, and brakes. The differential is also disassembled by removing case halves, bearings, gears, and other parts. Precise assembly steps list installing components in reverse order and include details like torque specifications.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before separating assembly components.
3. Reassembling the spring assembly in the tooling bench and using hydraulic force to compress the spring into position, requiring several tons of force. Proper centering and leveling of the assembly is critical.
This document provides the installation procedure for a final drive on an excavator. It lists the required tools and parts. The procedure involves using lifting devices to position the final drive, applying anti-seize compound to bolts, and torquing the bolts to the specified values. It also describes attaching lifting brackets and removing the lifting equipment once installation is complete.
The document is a service repair manual that provides step-by-step instructions for disassembling the final drive components of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, carrier assembly, planetary gears, and separating the sprocket housing from the motor housing. Detailed illustrations accompany each step to show how to remove individual parts like seals, shafts, and bearings from within the final drive assembly. Special tools are listed that may be required for tasks like removing retaining rings.
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into a motor housing in the correct order.
3. Attaching lifting devices and link brackets to install the assembled swing motor and remove the swing drive, which each weigh over 500 lbs.
This document provides instructions for removing and installing a swing motor on an excavator model 329D2 L. The removal procedure involves draining oil from the swing drive, using tools to remove bolts securing the swing drive, and using lifting equipment to remove the swing motor due to its weight of approximately 77 kg. The installation procedure outlines connecting harness assemblies, hoses, and tightening connections to specified torques.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D L Excavator (Prefix BFC) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling and assembling the transmission of a 329D L and 329D LN excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 36 steps for assembly, reinstalling these components in reverse order and noting cleaning requirements. Precise measurements are taken to determine the correct shim thickness for preloading bearings during assembly.
This document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. The disassembly process involves removing 27 components from the travel motor body and head. The assembly process reverses the disassembly steps and cautions that all components must be reinstalled in their original positions and orientations. Proper cleaning of components before and after disassembly and assembly is emphasized to prevent contamination of the hydraulic system.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant and outlines procedures for preparing the machine, removing and installing components like lines, the compressor, and performing functions like evacuating and charging the system. Personal protective equipment is required as the system is pressurized and contains refrigerant that can cause injury.
This document provides instructions for removing and installing a governor and fuel injection control linkage on an excavator. It begins with an overview of the required tools. The removal procedure involves disconnecting tubes and cables, removing clips and pins, and taking off bolts. The installation procedure specifies cleaning and lubricating parts, replacing seals, and using tools to install clips, pins and bolts in the reverse order of removal. Precautions are given to keep parts clean and check adjustments after installation.
Caterpillar Cat 320D2 L Excavator (Prefix YEA) Service Repair Manual Instant ...jkdkkdsmmd
This document provides assembly instructions for excavator models 320D2 and 320D2 L. It outlines 49 assembly steps requiring various tools. The steps include installing components like the pump housing, swashplate assemblies, shaft assemblies, barrel assemblies, port plates, head assembly, seal assembly, control linkage, and pump control components. Precautions are provided for steps involving released spring forces.
Caterpillar Cat 320D2 L Excavator (Prefix RAR) Service Repair Manual Instant ...jkdkkdsmmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C7.1 engine. It describes the required tools and outlines a multi-step process that involves positioning the piston at top dead center, compressing the valve spring with a tool to remove keepers and the spring, and reversing the process to install new springs. Safety notices are provided to wear protective equipment when working with compressed springs.
This document provides assembly instructions for excavator models 320D2 and 320D2 L. It outlines 49 assembly steps requiring various tools. The steps include installing components like the pump housing, swashplate assemblies, shaft assemblies, barrel assemblies, port plates, head assembly, seal assembly, control linkage, and pump control components. Precautions are provided for steps involving released spring forces.
The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 320D2 excavator engine. The flywheel removal procedure involves removing bolts and installing guide studs to lift the flywheel off. The crankshaft rear seal is part of a sealed assembly that must be replaced if removed. Installation involves aligning and pressing the new seal onto the crankshaft flange.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304E MINI HYD EXCAVATOR SSC
Configuration: 304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)
Disassembly and Assembly
303E CR, 303.5E, 304E, 305.5E and 305E Mini Hydraulic Excavators Machine
Systems
Media Number -UENR0148-04 Publication Date -01/10/2016 Date Updated -25/10/2016
i06906733
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
C 289-6053 Spanner Wrench 1
Illustration 1 g01243022
1. Install Duo-Cone Seal Gp (53).
1/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01243021
2. Install bearing (52) and Duo-Cone Seal Gp (51).
Illustration 3 g01243019
3. Install ring gear assembly (49) onto motor housing (50).
Illustration 4 g01243018
4. Use Tooling (C) to install nut (48).
5. Tighten nut (48) to a torque of 240 N·m (177 lb ft).
2/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01371953
6. Raise the temperature of bearing (48A).
7. Install bearing (48A) onto shaft (45).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Illustration 6 g01243016
8. Install spring (45) and seal (47).
3/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Illustration 10 g01243011
12. Install washers (37) and spring (38).
Illustration 11 g01243009
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
5/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 13. Use a suitable press and Tooling (B) to install retaining ring (36).
Illustration 12 g01243008
14. Install pins (35).
Illustration 13 g01243007
15. Install barrel (32), discs (33), and plates (34).
Illustration 14 g01243006
16. Install O-ring seals (31).
6/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g01244899
17. Install piston (30).
Illustration 16 g01243004
18. Install O-ring seals (28), O-ring seal (27), and springs (29).
Illustration 17 g01243003
19. Install bearing (26) and port plate (25).
7/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g01243001
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install head (23) and bolts (24). Tighten bolts (24) to a torque of 29 ± 5 N·m (21 ± 4 lb ft).
Illustration 19 g01243000
21. Install poppet (22).
8/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g01242998
22. Install spring (21).
Illustration 21 g01242996
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
23. Install the O-ring seal and plug (20). Tighten plug (20) to a torque of 196 ± 15 N·m
(145 ± 11 lb ft).
9/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g01242992
24. Install washers (16), coupling (17), washer (18), and setscrews (19).
Illustration 23 g01242991
25. Install bearings (14), gear (15), and gears (13).
Illustration 24 g01242989
26. Install retainers (12) and bolts (11). Tighten bolts (11) to a torque of 33 ± 5 N·m
(24 ± 4 lb ft).
10/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Do...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 25 g01242988
27. Install carrier (9) and washer (10).
Illustration 26 g01242987
28. Install bearings (7), gear (8), and gears (6).
Illustration 27 g01242984
29. Install retainer (5) and bolts (4). Tighten bolts (4) to a torque of 33 ± 5 N·m (24 ± 4 lb ft).
11/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Do...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 28 g01242982
30. Install cover (3), ring (1), and plug (2). Tighten plug (2) to a torque of 59 ± 10 N·m
(44 ± 7 lb ft).
End By:
a. Install the final drive and the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Feb 19 19:21:46 UTC+0800 2020
12/12
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Do...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 304E MINI HYD EXCAVATOR SSC
Configuration: 304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)
Disassembly and Assembly
303E CR, 303.5E, 304E, 305.5E and 305E Mini Hydraulic Excavators Machine
Systems
Media Number -UENR0148-04 Publication Date -01/10/2016 Date Updated -25/10/2016
i06799276
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 289-6052 Spanner Wrench 1
E 161-4350 Duo-Cone Seal Installation Gp 1
Illustration 1 g03779912
1. Use Tooling (E) to install Duo-Cone seal (58).
1/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g03779907
2. Install bearing (59). Use Tooling (E) to install Duo-Cone seal (58).
Illustration 3 g03779867
Illustration 4 g03779864
3. There is a count of 132 balls (57). Install balls (57).
4. Install plug (56).
2/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g01245010
5. Install ring gear (54) onto motor housing (55).
6. Use Tooling (D) to install nut (53). The torque of nut (53) is 196 ± 9.8 N·m (145 ± 7 lb ft).
7. Install bolts (52) and tighten to a torque of 6 ± 2 N·m (53 ± 18 lb in).
Illustration 6 g01245009
8. Install springs (50) and seal (51).
Illustration 7 g01246088
9. Raise temperature of bearing (48).
3/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 10. Install bearing (48) onto shaft (47).
Illustration 8 g01245007
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Install pistons (46), balls (49), shaft (47), and bearing (48).
Illustration 9 g01245005
12. Install swashplate (45).
4/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
15. Use a suitable press and Tooling (B) to install retaining ring (38).
Illustration 13 g01244999
16. Install pins (37).
Illustration 14 g01244997
17. Install plate (35) and barrel (36).
6/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g01244996
18. Install O-ring seals (34) and backup rings (33).
Illustration 16 g01244993
19. Install piston (32), springs (28), O-ring seal (29), O-ring seals (30), and O-ring seals (31).
Illustration 17 g01244992
20. Install port plate (25), bearing (27), and pins (26).
Note: Make sure that port plate (25) stays aligned with dowel during assembly.
7/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g01244991
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
21. Install head (24) and bolts (23) . Tighten bolts (23) to a torque of 64 ± 4 N·m (47 ± 3 lb ft).
Illustration 19 g01244989
22. Install spool (22).
8/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. Illustration 20 g01244988
23. Install spring (21) and retainer (20).
Illustration 21 g01244987
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install the O-ring seal and plug (19).
9/14
304E Mini Hydraulic Excavator SSC00001-UP (MACHINE)(SEBP6445 - 09) - Docu...
2020/2/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...