The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, pins, seals and other components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
This document provides assembly instructions for a piston pump in a 226B3 skid steer loader. It lists 78 steps to assemble internal components like bearings, seals, springs, and housing pieces. Tools required include rulers, pliers, drivers, pullers, and grease. Proper orientation of dowels, pins, and plates is emphasized. Torque specifications are provided for fittings and valves. The instructions caution that following the steps and wearing protective equipment is important due safety risks from spring-loaded components.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
This document provides assembly instructions for a piston pump in a 226B3 skid steer loader. It lists 78 steps to assemble internal components like bearings, seals, springs, and housing pieces. Tools required include rulers, pliers, drivers, pullers, and grease. Proper orientation of dowels, pins, and plates is emphasized. Torque specifications are provided for fittings and valves. The instructions caution that following the steps and wearing protective equipment is important due safety risks from spring-loaded components.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d l hydraulic excavator (prefix gge) service repair manua...jfdskekdmme
This document provides assembly instructions for excavator final drive models 330D L, 330D N, and 330D LN in 3 sentences:
The instructions list 59 steps and required tools to assemble the final drive components, including installing bearings and seals, assembling carrier assemblies, and testing the final seal. Cleanliness is important during assembly and O-rings, gaskets, and seals should always be replaced with new parts. Dimensions and torque specifications are provided to ensure proper assembly and installation of the final drive.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 d mh excavator (prefix pel) service repair manual (pel000...fjjskekdmme
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble various components of the pump such as pistons, bearings, gears, covers, and valves. Tools required include lever pullers, link brackets, and retaining ring pliers. Photos illustrate each step, and torque specifications are provided for fasteners. The overall process installs the pump, connects hoses and wiring, and mounts related components back onto the excavator.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...jfdjskmdmme
The document provides instructions for disassembling the piston pump of a M315C wheeled excavator. It describes removing 31 individual parts from the pump in a specific sequence, including the servo valve, charge pump, gears, head, relief valves, pistons, barrel assembly, swashplate assembly, and other components. Cleanliness is important during disassembly to prevent dirt from entering the internal mechanisms. Personal injury can result from hydraulic pressure still remaining in the system, so precautions are described.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...jfdjskmdmme
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, seals, pistons, and bearings. It then lists the assembly steps in reverse order, noting to clean parts and apply new thread lock before reinstalling components. Precautions are provided to mark parts for orientation and contain fluids during maintenance.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...jfdjskmdmme
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...jfdjskmdmme
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids during disassembly.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...jfdjskmdmme
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...jfdjskmdmme
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...jfdjskmdmme
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function of the travel motor.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...jfdjskmdmme
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly instructions then detail 27 steps to fully disassemble the travel motor. These include removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Throughout the process, technicians are warned to take care with components and contain any fluids.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...jfdjskmdmme
The document provides the disassembly procedure for a 330D2 excavator travel motor in 28 steps. It begins by instructing the technician to clean and secure the travel motor vertically, then remove the head by taking out bolts and marking parts for reassembly. Several internal components are then removed, including brake pistons, plates, and seals. The rotating assembly is separated from the housing using a prybar. Bearings and seals are removed from the shaft. Finally, the cam plate, pistons, seals and other remaining parts are disassembled from the housing. Throughout, precise steps and illustrations are provided to guide disassembly while maintaining part orientation.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids removed from the motor.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d l hydraulic excavator (prefix gge) service repair manua...jfdskekdmme
This document provides assembly instructions for excavator final drive models 330D L, 330D N, and 330D LN in 3 sentences:
The instructions list 59 steps and required tools to assemble the final drive components, including installing bearings and seals, assembling carrier assemblies, and testing the final seal. Cleanliness is important during assembly and O-rings, gaskets, and seals should always be replaced with new parts. Dimensions and torque specifications are provided to ensure proper assembly and installation of the final drive.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 d mh excavator (prefix pel) service repair manual (pel000...fjjskekdmme
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble various components of the pump such as pistons, bearings, gears, covers, and valves. Tools required include lever pullers, link brackets, and retaining ring pliers. Photos illustrate each step, and torque specifications are provided for fasteners. The overall process installs the pump, connects hoses and wiring, and mounts related components back onto the excavator.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...jfdjskmdmme
The document provides instructions for disassembling the piston pump of a M315C wheeled excavator. It describes removing 31 individual parts from the pump in a specific sequence, including the servo valve, charge pump, gears, head, relief valves, pistons, barrel assembly, swashplate assembly, and other components. Cleanliness is important during disassembly to prevent dirt from entering the internal mechanisms. Personal injury can result from hydraulic pressure still remaining in the system, so precautions are described.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...jfdjskmdmme
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, seals, pistons, and bearings. It then lists the assembly steps in reverse order, noting to clean parts and apply new thread lock before reinstalling components. Precautions are provided to mark parts for orientation and contain fluids during maintenance.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...jfdjskmdmme
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...jfdjskmdmme
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids during disassembly.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...jfdjskmdmme
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...jfdjskmdmme
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...jfdjskmdmme
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function of the travel motor.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...jfdjskmdmme
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly instructions then detail 27 steps to fully disassemble the travel motor. These include removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Throughout the process, technicians are warned to take care with components and contain any fluids.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...jfdjskmdmme
The document provides the disassembly procedure for a 330D2 excavator travel motor in 28 steps. It begins by instructing the technician to clean and secure the travel motor vertically, then remove the head by taking out bolts and marking parts for reassembly. Several internal components are then removed, including brake pistons, plates, and seals. The rotating assembly is separated from the housing using a prybar. Bearings and seals are removed from the shaft. Finally, the cam plate, pistons, seals and other remaining parts are disassembled from the housing. Throughout, precise steps and illustrations are provided to guide disassembly while maintaining part orientation.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids removed from the motor.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure reverses this process and puts the travel motor back together in 25 steps, reinstalling the parts in the reverse order that they were removed. Precise instructions are given for each step to ensure correct reassembly.
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...jfdjskmdmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...jfdjskmdmme
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. This includes removing covers, gears, shafts, bearings, seals and other components. Special tools are required to remove some parts, and safety notes are provided about cleanliness and part weights which require multiple people to handle. The overall goal is to break the final drive down into all of its individual parts for repair or replacement.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...jfdjskmdmme
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations supplement the written instructions.
3. Proper cleaning and application of sealant or retaining compound is emphasized to prevent contamination and ensure proper component life.
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...jfdjskmdmme
The document provides disassembly instructions for a final drive on an excavator model 330D L excavator. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing the cover, gears, plates, plugs, seals, carrier assembly, planetary gear assembly, shafts, springs, and bearings. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02344155
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
C 1P-1857 Retaining Ring Pliers 1
D 1P-0510 Driver Gp 1
E 1U-6396 O-Ring Assembly Compound 1
F 1P-1854 Retaining Ring Pliers 1
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. A reconditioning procedure should not be degraded
because of a low cost component such as an O-ring or a gasket. Use Tooling (E) during the
assembly procedure.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: Apply a light film of SAE 10W oil to all components before assembly.
1/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00882512
1. Use Tooling (D) in order to install bearing cup (27) .
Note: Bearing cup (27) must be fully seated. Bearing cup (27) must be properly seated in
order for the motor to assemble properly.
Illustration 2 g00882505
2. Rotate housing (3) . Use Tooling (D) in order to install seal (26) .
3. Use Tooling (C) in order to install retaining ring (25) .
2/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00883246
4. Install shaft (2) and bearing cone (16) in a suitable press. Press bearing cone (16) onto shaft
(2) .
Note: Bearing cone (16) must be fully seated. Bearing cone (16) must be properly seated in
order for the motor to assemble properly.
5. Assemble the rotating group in the following manner:
Illustration 4 g00882894
a. Install pins (24) in the top of barrel assembly (19) .
3/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00882494
b. Rotate barrel assembly (19) . Install washer (23) and spring (22) . Place retaining ring
(21) on top of spring (22) .
Note: Do not attempt to install retaining ring (21) .
Illustration 6 g00882927
c. Rotate the barrel assembly. Retain the contents of the barrel. Position guide (20) on
pins (24) .
d. Install shaft (2) and the bearing through the barrel assembly.
Note: The shaft will align the barrel assembly.
Illustration 7 g01163862
4/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
e. Install Tooling (A) and barrel assembly (19) into a suitable press.
f. Compress the spring. Use Tooling (F) in order to install retaining ring (21) .
g. Slowly release the pressure on barrel assembly (19) .
h. Remove the shaft from barrel assembly (19) .
Illustration 8 g00882451
6. Install pistons and plate (18) into barrel assembly (19) .
Illustration 9 g00882324
7. Install swashplate (17) onto rotating group (14) .
5/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Note: Barrel assembly (19) is rotating group (14) upon the installation of the pistons.
Note: Place identifying marks on swashplate (17) in order to locate two holes on the top of
the swashplate.
Illustration 10 g00882976
8. Install shaft (2) into rotating group (14) .
Note: Splines in shaft (2) must engage splines in rotating group (14) .
Illustration 11 g00882984
6/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 12 g00882988
9. Align swashplate (17) with housing (3) .
Note: The holes on the top of swashplate (17) must engage the dowels in housing (3) .
Illustration 13 g00882991
10. Install rotating group (14) into housing (3) .
Illustration 14 g00882992
7/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 11. Raise the temperature of sleeve (15) . Install sleeve (15) onto shaft (2) .
Illustration 15 g00882156
12. Install shim (13) onto shaft (2) .
Illustration 16 g00882123
13. Install bearing cone (12) onto shaft (2) .
Note: Bearing cone (12) is a slip fit.
8/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 17 g00882112
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install valve assembly (9) , sleeve (10) , and plug (11) into cover (5) .
Illustration 18 g00881963
15. Use Tooling (A) to install bearing cup (8) into cover (5) .
9/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 19 g00883138
Illustration 20 g00881953
16. Install port plate (6) onto cover (5) .
Note: Take note of the slot in the reverse side of port plate (6) . The slot will receive the
dowel in cover (5) .
17. Install O-ring seal (7) on cover (5) .
Illustration 21 g00881945
10/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 18. Install cover (5) onto housing (3) .
19. Secure cover (5) with bolts (4) .
Illustration 22 g00881939
20. Install key (1) into shaft (2) .
End By: Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install ".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 17 13:43:50 UTC+0800 2020
11/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02344156
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g00883712
1. Position piston motor (23) into the bracket. Secure the piston motor with bolts (22) .
Illustration 2 g00883819
2. Install adapter (21) onto the piston motor.
Illustration 3 g00883705
3. Install nut (20) , fan blade (19) , and bolts (18) .
2/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 4 g00883690
4. Attach a suitable lifting device to the piston motor and fan assembly (17) . The weight of the
piston motor and fan assembly (17) is approximately 29 kg (65 lb). Position the piston
motor and fan assembly (17) . Install bolts (16) .
Illustration 5 g00883675
5. Install hose assemblies (15) .
3/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g00883666
6. Install upper fan guard (14) and bolts (13) .
Illustration 7 g00883641
7. Install tube assemblies (10) and (9) . Install bolts (12) and (11) .
Illustration 8 g00883636
8. Slide the hoses from tube assemblies (10) and (9) into position. Install hose clamps (8) .
4/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 9 g00883581
9. Install strap (7) and bolts (6) .
Illustration 10 g00883563
10. Install brace (5) and bolts (4) .
Illustration 11 g00883517
11. Install plates (1) , (2) , and (3) . Install the bolts.
5/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i04776349
Gear Pump (Fan Drive) - Remove
SMCS - 1387-011-GT; 5073-011-HFN
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the hydraulic oil tank into a suitable container for storage or disposal.
The capacity of the hydraulic oil tank is 175 L (46 US gal).
1/2(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g02883378
Illustration 2 g02879096
2. Remove hose assemblies (2) and (3).
3. Remove nuts (1). Remove gear pump (4).
4. Remove nut (5). Remove gear (6), gasket (8), flange (9), key (10), and the O-ring seal.
5. Use a suitable press to remove bearing (7) from gear (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 17 13:45:42 UTC+0800 2020
2/2(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i04959810
Gear Pump (Fan Drive) - Install
SMCS - 1387-012-GT; 5073-012-HFN; 5073
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/3(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g02879096
1. Use a suitable press to Install bearing (7) onto gear (6).
2. Install key (10). Install the O-ring seal onto flange (9). Install flange (9), gasket (8). Install
gear (6) and nut (5).
Note: Do not tighten nut at this time. The gear pump must be installed on the engine before
the nut is tightened. This procedure will prevent the pump from being damaged internally.
Illustration 2 g02883378
3. Position gear pump (4).
4. Secure gear pump (4) into position with bolts and nuts (1).
5. Remove the front access cover (not shown) in order to tighten nut (5). Tighten nut (5) to a
torque of 80 ± 8 N·m (59 ± 6 lb ft).
6. Install the front access cover.
7. Connect hose assemblies (2) and (3).
2/3(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i01796054
Handle (Joystick) - Remove and Install
SMCS - 5705-010
Removal Procedure
Illustration 1 g00739085
1. Remove the cover from the front of the console. Remove screws (1) .
1/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 2 g00739101
2. Remove screws (2) from the rear of the console.
Illustration 3 g00739106
3. Open armrest (3). Remove screws (4). Remove armrest (3) .
Illustration 4 g00739111
2/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 4. Reposition cover (6) in order to access the harness assembly on the right hand console.
Disconnect harness assembly (5) .
5. Remove cover (6) from the console.
Illustration 5 g00739116
6. Disconnect harness assembly (7) from the joystick.
Illustration 6 g00739127
7. Lift rubber boot (8) over handle (9) .
Note: Mark the location of locknut (10) and the handle for installation procedures.
8. Hold nut (11). Loosen locknut (10). Unscrew handle (9) in order to remove the handle.
9. Remove rubber boot (8) from the handle.
Installation Procedure
3/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...