The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...shudun96087
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. Key steps include:
1. Marking connecting rods and caps before removal to ensure proper reinstallation.
2. Removing bolts and caps to separate connecting rods from pistons.
3. Reassembling pistons and connecting rods, ensuring components are installed in their original locations and orientations. Proper ring installation and bearing fitting are critical.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...yfbr995309
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components. Proper clearances and orientation are checked during assembly.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...kesi7153062
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing new bearings into the connecting rods, installing piston rings, and reinstalling the pistons and connecting rods back into the engine.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components in reverse order. Proper heating and cooling procedures are specified for the connecting rod bearings.
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. It describes removing the cylinder head, oil pump, and piston cooling jets before removing each piston and connecting rod assembly. The connecting rod cap and bearings are removed, then the piston and connecting rod are separated. Reinstallation follows the reverse order, applying anti-seize compound and using tools to properly seat the piston rings and install the connecting rod bearings.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...f8usiedkdmm
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...shudun96087
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their respective caps and cylinders.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin, and reinstalling the components. Proper identification and orientation is important for correct reassembly.
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. Key steps include:
1. Marking connecting rods and caps before removal to ensure proper reinstallation.
2. Removing bolts and caps to separate connecting rods from pistons.
3. Reassembling pistons and connecting rods, ensuring components are installed in their original locations and orientations. Proper ring installation and bearing fitting are critical.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...yfbr995309
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components. Proper clearances and orientation are checked during assembly.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...kesi7153062
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing new bearings into the connecting rods, installing piston rings, and reinstalling the pistons and connecting rods back into the engine.
1) The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine.
2) Key steps include removing the cylinder head, oil pump, and piston cooling jets before removing the pistons and connecting rods. Pistons and connecting rods must be kept with their identifying marks and installed in the original locations.
3) Reassembly involves pressing in new connecting rod bearings, installing piston rings, inserting the piston and pin with retaining rings, and reinstalling the components in reverse order. Proper heating and cooling procedures are specified for the connecting rod bearings.
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. It describes removing the cylinder head, oil pump, and piston cooling jets before removing each piston and connecting rod assembly. The connecting rod cap and bearings are removed, then the piston and connecting rod are separated. Reinstallation follows the reverse order, applying anti-seize compound and using tools to properly seat the piston rings and install the connecting rod bearings.
Caterpillar Cat 329D L Excavator (Prefix EBM) Service Repair Manual (EBM00001...f8usiedkdmm
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 EXCAVATOR TMJ
Configuration: 329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292267
Engine Oil Cooler - Install - Engine Oil Cooler with a Low
Mounted Filter Base
SMCS - 1378-012
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Ensure that wiring harness are correctly routed and the cable straps
are not over tightened. Over tightening of the cable straps will damage
the wiring harness convoluting.
1/6
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g03408820
1. If necessary, follow Step 1.a through Step 1.d in order to assemble engine oil cooler (5).
a. Ensure that engine oil cooler matrix (10) is clean, free from damage and restriction.
Replace engine oil cooler matrix (10) if damaged or restricted.
b. Ensure that spacer plate (11) is clean and free from damage. Replace spacer plate (11)
if damaged.
c. Position a new gasket (10) onto spacer plate (17). Install engine oil cooler matrix (9)
to the spacer plate.
d. Install bolts (8) finger tight.
2/6
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g03408908
3/6
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g03408917
2. Clean the gasket surfaces of the cylinder block.
3. Install Tooling (A) into Position (B).
4. Position a new gasket (7) (not shown) onto Tooling (A). Ensure that the gasket is correctly
orientated.
5. Install the assembly of engine oil cooler (5) to the cylinder block.
6. Install bolts (6) to engine oil cooler (5) finger tight. Support the engine oil cooler as the
bolts are installed.
Note: Ensure that the bolts of different lengths are installed in the correct position.
7. Remove Tooling (A) and install remaining bolts (6).
4/6
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g03408818
8. If the engine has a low mounted oil filter (1) on the left-hand side, install the oil filter base.
Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct
procedure.
9. If the engine has a right-hand side oil filter, follow Step 9.a through Step 9.d in order to
install blanking plate (2).
a. Install bolts (4) to blanking plate (2).
b. Position a new gasket (3) (not shown) onto blanking plate (2).
c. Install the assembly of blanking plate (2) to the assembly of the engine oil cooler.
d. Tighten bolts (4) to a torque of 22 N·m (195 lb in).
5/6
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g03408914
Tightening sequence for an engine oil cooler with a blanking plate or with a low mounted oil filter base
10. Tighten the bolts to a torque of 22 N·m (195 lb in) in the sequence that is shown in
Illustration 5.
11. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change" for the correct procedure.
12. Check the level of the engine lubricating oil. Refer to Operation and Maintenance Manual,
"Engine Oil Level - Check" for the correct procedure.
End By:
a. Install the mounting bracket for the Electronic Control Module (ECM) . Refer to
Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 25 18:15:55 UTC+0800 2020
6/6
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 EXCAVATOR TMJ
Configuration: 329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292279
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g03409484
1. If suction pipe (5) has a support bracket, remove bolt (7) from bracket (8). Remove bolt (6)
for the retaining clip.
2. Remove bracket (8).
Note: Note the position and orientation of the components for the support bracket.
3. Remove bolts (4) from suction pipe (1).
4. Remove suction pipe (5) from oil pump (2).
5. Remove gasket (3) (not shown).
6. Remove bolts (1) and remove the assembly of engine oil pump (2) from the cylinder block.
2/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g03409496
7. If necessary, follow Step 7.a through step 7.c to disassemble engine oil pump assembly (2).
a. Remove bolts (11).
b. Remove front cover assembly (12) from engine oil pump assembly (2).
c. Make temporary mark on outer rotor (13) for assembly purposes. Remove the outer
rotor from of engine oil pump (2).
8. Do not remove dowel (9) or dowel (10) from the housing of the engine oil pump unless the
dowels are damaged.
3/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g03409497
9. If necessary, follow Step 9.a through step 9.c to remove cross over tube assembly (14).
a. Remove bolts (15) and bolts (16) from cross over tube assembly (14).
b. Remove cross over tube assembly (14) from the cylinder block.
c. Remove gasket (17) and gasket (18).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 25 18:16:51 UTC+0800 2020
4/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 EXCAVATOR TMJ
Configuration: 329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292278
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
7H-1942 Dial Indicator 1
- Magnetic Base and Stand 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
If any part of the engine oil pump is worn or damaged, the complete
assembly of the engine oil pump must be replaced.
1. Ensure that all components of the engine oil pump are clean and free from wear and
damage. Refer to System Operation, Testing and Adjusting, "Engine Oil Pump - Inspect"
1/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. for more information. Replace the complete assembly of the engine oil pump if any of the
components are worn or damaged.
Illustration 1 g03409497
2. If necessary, follow Step 2.a through step 2.d to install cross over tube assembly (14).
a. Install new gasket (17) and new gasket (18).
b. Position cross over tube assembly (14) onto the cylinder block.
c. Install bolts (15) and bolts (16) to cross over tube assembly (14) finger tight.
d. Tighten bolts (15) and bolts (16) to a torque of 22 N·m (195 lb in).
2/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g03409496
3. If necessary, follow Step 3.a through step 3.d to assemble engine oil pump assembly (2).
a. Lubricate the internal components for the assembly of the engine oil pump with clean
engine oil.
b. Install outer rotor (13) to oil pump assembly (2). Ensure that the outer rotor is
installed in the outer rotor original position and orientation.
c. Install front cover assembly (12) to engine oil pump assembly (2).
d. Install bolts (11) finger tight. Tighten the bolts to a torque of 22 N·m (195 lb in).
4. Ensure that dowel (9) and dowel (10) are correctly located in the housing of engine oil
pump (2).
5. Install bolts (7). Tighten the bolts to a torque of 22 N·m (195 lb in).
6. Install the assembly of engine oil pump (2) to the cylinder block. Ensure that dowel (9) and
dowel (10) are correctly aligned with the holes in the cylinder block.
7. Install bolts (1) to assembly of engine oil pump (2). Tighten the bolts to a torque of 22 N·m
(195 lb in).
8. Use Tooling (A) to check the backlash between idler gear and the crankshaft gear. Refer to
Specifications, "Gear Group (Front)" for more information.
3/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 9. If suction pipe (5) had a support bracket, Follow Step 9.a through Step 9.e in order to install
support bracket and the suction pipe.
a. Install a new gasket (3) (not shown) to suction pipe (5).
b. Install bolts (4) to suction pipe (1).
c. Position the assembly of suction pipe (5) onto oil pump (2). Tighten bolts (4) to a
torque to 22 N·m (195 lb in).
d. Position bracket (8) onto cylinder block and retaining clip. Install bolt (7) to the
bracket. Install bolt (6) to the retaining clip. Hand tighten the bolts.
Note: Ensure the correct location and orientation of the bracket and the retaining clip.
e. Tighten bolt (6) to a torque of 22 N·m (195 lb in).
Tighten bolt (7) to a torque of 44 N·m (32 lb ft).
Note: Ensure that the suction pipe and the bracket are not strained as the bolts are
tightened.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install"
for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 25 18:17:47 UTC+0800 2020
4/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 EXCAVATOR TMJ
Configuration: 329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292437
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
a. Remove the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove
and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/2
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct procedure.
2. Loosen the hose clamps and remove the hose from the water pump inlet.
Illustration 1 g03434676
3. Remove bolts (4), bolts (5), and bolts (6). Identify the positions of bolts of different length.
4. Remove water pump (3) from front cover (1).
Note: If necessary, tap the water pump with a soft faced hammer in order to loosen the
water pump.
5. Remove gasket (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 25 18:18:42 UTC+0800 2020
2/2
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 EXCAVATOR TMJ
Configuration: 329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292436
Water Pump - Install
SMCS - 1361-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Studs
M8 by 90 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Ensure that the water pump is clean and free from wear and damage. If necessary, replace
the water pump. Clean the gasket surface of the water pump.
Illustration 1 g03434736
2/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g03413498
2. Clean the gasket surface of front cover (1).
3. Install Tooling (A) in Position (X).
4. Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket onto
the front cover.
5. Align water pump (3) to Tooling (A). Install the water pump to front cover (1).
Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
6. Install bolts (4), bolts (5), and bolts (6). Refer to Illustration 1. Tighten the bolts finger tight.
7. Remove Tooling (A) and install the remaining bolts.
3/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Illustration 3 g03413499
8. Tighten bolts (4), bolts (5), and bolts (6) in the sequence that is shown in Illustration 3 to a
torque of 22 N·m (195 lb in).
9. Install the hose to the water pump inlet. Tighten the hose clamps securely.
10. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Change" for the correct procedure.
End By:
a. Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and
Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 25 18:19:38 UTC+0800 2020
4/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D2 EXCAVATOR TMJ
Configuration: 329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292439
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system to a level below the water temperature regulator,
into a suitable container for storage or for disposal. Refer to Operation and Maintenance
Manual, "Cooling System Coolant - Change" for the correct draining procedure.
2. Loosen the hose clamps from the upper radiator hose and disconnect the upper radiator hose
from water temperature regulator housing (2).
1/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01336665
Typical example
3. Remove bolts (1) from water temperature regulator housing (2).
4. Remove water temperature regulator housing (2) from the cylinder head.
Note: Note the orientation of the water temperature regulator housing.
Illustration 2 g01336667
Typical example
5. Remove O-ring seal (3) from water temperature regulator housing (2).
Installation Procedure
2/4
329D2 & 329D2 L Excavators TMJ00001-UP (MACHINE) POWERED BY C7.1 Eng...
2020/4/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...