The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing lips seals, keys, cam plate, barrel assembly, piston guide and more. Detailed illustrations accompany each step to ensure proper reassembly. Precautions are provided to prevent injury from released springs and to correctly install parts like the cam plate.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 326 f l excavator (prefix xfk) service repair manual (xfk0000...fjsekdmmeed
The document provides instructions for disassembling a travel motor. It describes 28 steps to remove components such as the head, springs, seals, plates, bearings, and housing. Various tools are required including an adapter, bolts, threaded rods, nuts, washers, lifting eyes, a crossblock, and a push-puller plate. Safety precautions are provided to prevent injury from released spring forces.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 323 excavator with a C7.1 engine.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The flywheel ring gear can then be removed by heating and punching.
3. Flywheel installation requires cleaning, installing the ring gear by heating and pressing it on, checking the rear seal for leaks, lifting the flywheel onto guide studs and torquing the bolts.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...fujskekfmsme
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then lists 12 steps for reassembly, starting with installing a lip seal and finishing by reinstalling covers. Precautions are provided regarding cleaning parts and applying oil before assembly.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...fjkskedmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and multi-step procedures for removal and installation, which include removing other engine components, using specialty tools to remove the guides and seats, cleaning parts, and ensuring proper installation height or alignment. Safety notices are provided to keep parts clean and contain fluids properly during the process.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 326 f l excavator (prefix xfk) service repair manual (xfk0000...fjsekdmmeed
The document provides instructions for disassembling a travel motor. It describes 28 steps to remove components such as the head, springs, seals, plates, bearings, and housing. Various tools are required including an adapter, bolts, threaded rods, nuts, washers, lifting eyes, a crossblock, and a push-puller plate. Safety precautions are provided to prevent injury from released spring forces.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 323 excavator with a C7.1 engine.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The flywheel ring gear can then be removed by heating and punching.
3. Flywheel installation requires cleaning, installing the ring gear by heating and pressing it on, checking the rear seal for leaks, lifting the flywheel onto guide studs and torquing the bolts.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...fujskekfmsme
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then lists 12 steps for reassembly, starting with installing a lip seal and finishing by reinstalling covers. Precautions are provided regarding cleaning parts and applying oil before assembly.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...fjkskedmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and multi-step procedures for removal and installation, which include removing other engine components, using specialty tools to remove the guides and seats, cleaning parts, and ensuring proper installation height or alignment. Safety notices are provided to keep parts clean and contain fluids properly during the process.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, brake piston, and shaft. The assembly process describes 23 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and seals. Special tools may be required and clean hydraulic oil should be applied to sliding surfaces during reassembly.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 315 d l excavator (prefix cjn) service repair manual (cjn0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing bolts, seals, plates, and other components. It then lists 26 steps for assembly, which involves cleaning components, applying seals and lubricants, and reinstalling components in reverse order of disassembly. Special care must be taken to align parts properly and not damage surfaces.
Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm4000...fjsjekkmdmme
The document provides instructions for disassembling a travel motor. It involves 28 steps including removing the head, port plate, springs, pistons, seals, and other components. Tools required include an adapter, nuts, washers, threaded rod, bolts, eyebolts, retaining ring pliers, a bearing puller group, and other specialized tools to remove components in a specific sequence while taking safety precautions for parts under spring pressure.
Caterpillar cat 325 f lcr excavator (prefix yca) service repair manual (yca00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It includes 25 steps for disassembly and 22 steps for assembly. Key steps include removing the head from the motor body, removing internal components like springs and pistons, and reinstalling them in reverse order during assembly. Precise positioning of parts is emphasized to ensure proper function when reassembled.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...fjjskekdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 25 steps for disassembly that involve removing components like the head, fittings, seals, pistons, and shaft assembly. It then lists 21 steps for assembly that involve cleaning components, applying lubricants, and reinstalling components in the reverse order of disassembly while ensuring proper alignment and positioning. Precautions are provided to contain fluids, properly handle springs, and correctly install certain components like keys to prevent damage.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...djdksmmdmd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, applying specified lubricants and ensuring proper alignment of parts.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...dikskedmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...shun96145luo
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and keys in their proper positions and applying sealant and grease as needed. The goal is to take the travel motor fully apart and then rebuild it correctly with all components returned to their original locations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7useijdkdmd1
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 315 d l excavator (prefix jha) service repair manual (jha0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing the head, check valves, fittings, brake piston, friction plates, and other components. It then lists 26 steps for assembly that describe cleaning and installing components like the shaft assembly, cam plate, barrel assembly, brake piston, and seals in the reverse order of disassembly. Precise alignment of parts and use of identification marks are emphasized to ensure correct reassembly.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, brake piston, and shaft. The assembly process describes 23 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and seals. Special tools may be required and clean hydraulic oil should be applied to sliding surfaces during reassembly.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 315 d l excavator (prefix cjn) service repair manual (cjn0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly that include removing bolts, seals, plates, and other components. It then lists 26 steps for assembly, which involves cleaning components, applying seals and lubricants, and reinstalling components in reverse order of disassembly. Special care must be taken to align parts properly and not damage surfaces.
Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm4000...fjsjekkmdmme
The document provides instructions for disassembling a travel motor. It involves 28 steps including removing the head, port plate, springs, pistons, seals, and other components. Tools required include an adapter, nuts, washers, threaded rod, bolts, eyebolts, retaining ring pliers, a bearing puller group, and other specialized tools to remove components in a specific sequence while taking safety precautions for parts under spring pressure.
Caterpillar cat 325 f lcr excavator (prefix yca) service repair manual (yca00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It includes 25 steps for disassembly and 22 steps for assembly. Key steps include removing the head from the motor body, removing internal components like springs and pistons, and reinstalling them in reverse order during assembly. Precise positioning of parts is emphasized to ensure proper function when reassembled.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...fjjskekdmme
The document provides instructions for disassembling and assembling a travel motor. It lists 25 steps for disassembly that involve removing components like the head, fittings, seals, pistons, and shaft assembly. It then lists 21 steps for assembly that involve cleaning components, applying lubricants, and reinstalling components in the reverse order of disassembly while ensuring proper alignment and positioning. Precautions are provided to contain fluids, properly handle springs, and correctly install certain components like keys to prevent damage.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...djdksmmdmd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, applying specified lubricants and ensuring proper alignment of parts.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...dikskedmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...shun96145luo
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and keys in their proper positions and applying sealant and grease as needed. The goal is to take the travel motor fully apart and then rebuild it correctly with all components returned to their original locations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7useijdkdmd1
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Similar to Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 and up) (10)
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c excavator (prefix kdd) service repair manual (kdd00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix jnk) service repair manual (jnk00001 ...jdfjskekmdme
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c excavator (prefix jcd) service repair manual (jcd00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The disassembly process involves removing 28 components from the travel motor in 28 steps, including removing the head, brake piston, rotating assembly, seals, and other internal parts.
2. Cleanliness is important during disassembly and assembly to prevent contamination. All parts should be cleaned and lubricated before assembly.
3. The assembly process reverses the disassembly steps, involving installing 28 components in 28 steps to reassemble the travel motor. Special tools and torque specifications are provided.
Caterpillar cat 330 c excavator (prefix jab) service repair manual (jab00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix haa) service repair manual (haa00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing seals and installing components in the reverse order of disassembly.
- Tools required include an adapter, nuts, washers, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound.
Caterpillar cat 330 c excavator (prefix gkx) service repair manual (gkx00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) Similarly, it outlines 28 steps for assembly, instructing technicians to replace all seals and gaskets and apply lubricant before reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout the process.
Caterpillar cat 330 c excavator (prefix gag) service repair manual (gag00001 ...jdfjskekmdme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor. It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
2) The assembly section lists 29 steps to reassemble the travel motor by replacing components in the reverse order of disassembly. Special tools are required for tasks like removing races and installing seals and rings.
3) Cleanliness is important during disassembly and assembly. Marks should be made to ensure parts are replaced in the same positions. Seal surfaces require compound and components need light oil applied before assembly.
Caterpillar cat 330 c excavator (prefix btm) service repair manual (btm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It details 28 steps for disassembly, removing components like the head, port plate, springs, brake piston, plates, and bearings. It then details 21 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Tools required are also listed.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator including:
1. The cylinder head removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts in a specific tightening sequence.
3. Removing the spacer plate requires taking out seals and removing the plate from the cylinder head. Installing requires new seals and gaskets and ensuring surfaces are clean.
Caterpillar cat 330 b l excavator (prefix 8sr) service repair manual (8sr0000...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b l excavator (prefix 5ls) service repair manual (5ls0000...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, tightening bolts in sequences, and verifying end play. The crankshaft removal requires aligning timing marks, removing caps and nuts, pushing pistons down, lifting the crankshaft out using brackets, and removing gears and seals.
Caterpillar cat 330 b l excavator (prefix 4rs) service repair manual (4rs0000...jdfjskekmdme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe procedures for removing and installing the cylinder head, rocker shaft and pushrods. Specifically, they outline removing the cylinder head by first removing associated components like the fuel lines, exhaust manifold, and rocker shaft. They then describe loosening bolts and using lifting devices to remove the heavy cylinder head. Procedures are also provided for disassembling, cleaning, inspecting, and reassembling the rocker shaft.
Caterpillar cat 330 b excavator (prefix 9hn) service repair manual (9hn00001 ...jdfjskekmdme
This document provides instructions for removing and installing final drives on an excavator. Key steps include:
1. Releasing hydraulic pressure and removing the track assemblies.
2. Removing bolts and disconnecting hydraulic lines to separate the final drive from the undercarriage frame.
3. Cleaning components and installing new seals before reassembling in reverse order, taking care to properly tighten bolts and reconnect hydraulic components.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8sr) service repair manual (8sr00001 ...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b excavator (prefix 5ls) service repair manual (5ls00001 ...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, torquing fasteners, and aligning identification marks. The crankshaft removal requires lifting it straight up after removing connecting rods, main bearing caps, and thrust plates.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325F EXCAVATOR NDJ
Configuration: 325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
325F Excavator Machine Systems
Media Number -UENR6794-05 Publication Date -01/09/2018 Date Updated -18/09/2018
i07505849
Travel Motor - Disassemble
SMCS - 4351-015
S/N - NDJ1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
E
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0298 Bolt 2
Start By:
a. Remove the travel motor.
1/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06341880
1. Attach the travel motor to Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
2. Remove plugs (1) and the O-ring seals.
Illustration 2 g06344110
3. Remove plug (2) and the O-ring seal. Repeat for the opposite side.
Illustration 3 g06341912
2/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plug (2A) and the O-ring seal. Repeat for the opposite side.
Illustration 4 g06341915
5. Remove spring (3).
Illustration 5 g06341917
6. Remove spool (4).
3/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g06341942
Illustration 7 g06342000
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (5) and cap (6). Repeat for the opposite side.
8. Remove O-ring seal (10) from cap (6). Remove guide (9), spring (8), and washer (7) from
the head assembly. Repeat for the opposite side.
4/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g06342005
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (11), O-ring seal (12), spring (13), and ball (14) from cap (6). Repeat for the
other cap.
Illustration 9 g06342009
10. Remove spool (15).
5/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g06343314
Illustration 11 g06343315
11. Remove relief valve (16). Remove O-ring seal (17) from relief valve (16).
12. Repeat for the opposite side.
Illustration 12 g06343359
6/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove the nuts of Tooling (B). Remove bolts (19) from head assembly (18).
Illustration 13 g06343366
14. Use Tooling (C) and a suitable lifting device to remove head assembly (18). The weight of
head assembly (18) is approximately 21 kg (47 lb).
Illustration 14 g06343374
15. Remove control plate (20) and bearing (21) from head assembly (18).
7/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g06343381
16. Remove pins (22) and springs (23).
17. Remove O-ring seals (24) and (25).
Illustration 16 g06343383
18. Use Tooling (D) and a suitable lifting device to remove housing assembly (26) from
Tooling (A) and place on a suitable bench.
Illustration 17 g06343417
8/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. To avoid personal injury, always wear eye and face protection when
using pressurized air.
19. Attach Tooling (E) to housing (26). Use air pressure to unseat brake piston (27). Remove
Tooling (E) and brake piston (27).
Illustration 18 g06343437
20. Remove back up rings (28) and O-ring seals (29) from brake piston (27).
Illustration 19 g06343462
21. Remove brake piston guide (30).
9/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g06343464
22. Remove O-ring seal (31) from brake piston guide (30).
Illustration 21 g06343466
Illustration 22 g06343469
Note: Note the orientation of friction discs (32) and plates (33) for assembly purposes.
23. Remove friction discs (32) and plates (33).
10/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g06343638
24. Remove rotating group (34) from housing (26).
Illustration 24 g06343777
25. Remove pistons (35) and retainer (36) from barrel (37).
Illustration 25 g06343783
26. Remove hold down ball (38) and springs (39) from barrel (37).
11/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g06343786
27. Remove swashplate (40) from housing (26).
Illustration 27 g06343788
Illustration 28 g06343793
28. Remove pistons (41).
29. Remove springs (42) and shaft (43).
12/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g06343795
30. Remove balls (46).
31. Remove bearing (44) and lip seal (45).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 13:06:56 UTC+0800 2020
13/13
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325F EXCAVATOR NDJ
Configuration: 325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
325F Excavator Machine Systems
Media Number -UENR6794-05 Publication Date -01/09/2018 Date Updated -18/09/2018
i01894672
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1P-0510 Driver Gp 1
D 5P-3413 Pipe Sealant 1
E 9S-3263 Thread Lock Compound 1
F 1U-6396 O-Ring Assembly Compound 1
G 5P-0960 Molybdenum Grease 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
1/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft assembly (34).
3. Raise the temperature of bearing (36). Install bearing (36) on shaft assembly (34). Install the
bearing until the bearing contacts the retaining ring.
4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft assembly (34) until the inner race is seated against
the shoulder on the shaft assembly.
Illustration 3 g00651891
(a) Body
6. Use Tooling (D) to apply a thin coat on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (C) in order to install lip seal (38).
2/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 8. Install lip seal (38) in the body of the travel motor. Install the lip seal so that the sealing lip
is facing in the direction that is shown. Make sure that the lip seal contacts the counterbore
in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
3/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 5 g00510547
12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
Illustration 6 g00510504
13. Install springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
4/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
5/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 9 g00651967
18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
6/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
24. Apply a thin coat of hydraulic oil on the surfaces of brake piston (14) which contact the
body of the travel motor. Install brake piston (14) in the body of the travel motor by hand. It
may be necessary to use a soft faced hammer to seat the brake piston correctly.
Illustration 12 g00878299
7/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 13 g01000124
25. Install washer set (13) in piston (14), as shown.
26. Install O-ring seals (12) in the body of the travel motor, as shown.
Illustration 14 g00510605
27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
8/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 28. Install the O-ring seals on fittings (10). Use Tooling (D) on the threads of fittings (10).
Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
Illustration 17 g00510341
30. Use Tooling (E) on the threads of the check valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Use Tooling (F) on port plate (4). Install the port plate in the port plate's original position on
the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
9/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Use Tooling (G) on shims (5). Install the shim or shims on the head. The grease will hold
the shim or shims in place during the installation of the head. Install the head on the body of
the travel motor.
Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 10 13:07:52 UTC+0800 2020
10/10
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325F EXCAVATOR NDJ
Configuration: 325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
325F Excavator Machine Systems
Media Number -UENR6794-05 Publication Date -01/09/2018 Date Updated -18/09/2018
i07505850
Travel Motor - Assemble
SMCS - 4351-016
S/N - NDJ1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
1/12
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g06343795
1. Install lip seal (45) and bearing (44).
2. Install balls (46).
Illustration 2 g06343793
Illustration 3 g06343788
3. Install shaft (43) and springs (42).
4. Install pistons (41).
2/12
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 4 g06343786
5. Install swashplate (40) into housing (26).
Illustration 5 g06343783
6. Install springs (39) and hold down ball (38) into barrel (37).
Illustration 6 g06343777
7. Install retainer (36) and piston (35) into barrel (37).
3/12
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine(M0086...
2020/6/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...