The document provides instructions for disassembling and assembling the swivel and swing motor components of an excavator. It describes removing 11 components from the swivel including covers, seals, bolts and housings. It then describes assembling the swivel in reverse order. For the swing motor, it lists removing 18 components including guards, tubes, valves, seals, springs and bearings. It also provides instructions for disassembling the swing motor piston assembly.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and removing bolts and seals to separate the swivel housing, rotor, and cover.
2. Cleaning and installing seals and O-rings before positioning the rotor and housings back together.
3. Disconnecting hydraulic and electrical lines before removing the swing motor using lifting brackets.
4. Cleaning the swing motor and area before installation in reverse order.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil to seals before reassembling components in reverse order.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor from the excavator.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Some key points:
- To disassemble the swivel, remove covers, seals, and separate the rotor from the housing using lifting devices.
- To assemble the swivel, apply oil to seals, position components, and secure with bolts in reverse order of disassembly.
- To remove the swing motor, disconnect hoses and wiring, remove bolts, and lift out the motor using lifting brackets.
- To disassemble the swing motor further, remove valves, seals, and springs after removing the motor from the excavator.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, bolts and the cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to remove the swing motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate components like the piston from the barrel.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and marking parts before disassembly of the swivel. Removing seals, covers, and housing components to separate the rotor.
2. Reassembling requires applying oil to seals and housing components before reinstalling them in reverse order.
3. For the swing motor, disconnecting hydraulic and electrical lines before removing bolts and lifting out the motor. Disassembly requires removing valves, seals and backup rings from the motor housing.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. It describes removing parts like seals, bolts, plates and pistons from the swivel and motor housing. Tools needed include wrenches, pullers, and lifting devices. Proper cleaning and marking of parts is emphasized to aid reassembly. Detailed illustrations accompany each step for reference.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil to seals before reassembling components in reverse order.
3. Draining swing motor oil before disconnecting hoses and removing bolts to lift out the motor.
4. Dismantling the swing motor involves removing springs, seals, pistons and other internal parts in a specific sequence.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and removing bolts and seals to separate the swivel housing, rotor, and cover.
2. Cleaning and installing seals and O-rings before positioning the rotor and housings back together.
3. Disconnecting hydraulic and electrical lines before removing the swing motor using lifting brackets.
4. Cleaning the swing motor and area before installation in reverse order.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil to seals before reassembling components in reverse order.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor from the excavator.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Some key points:
- To disassemble the swivel, remove covers, seals, and separate the rotor from the housing using lifting devices.
- To assemble the swivel, apply oil to seals, position components, and secure with bolts in reverse order of disassembly.
- To remove the swing motor, disconnect hoses and wiring, remove bolts, and lift out the motor using lifting brackets.
- To disassemble the swing motor further, remove valves, seals, and springs after removing the motor from the excavator.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, bolts and the cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to remove the swing motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate components like the piston from the barrel.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and marking parts before disassembly of the swivel. Removing seals, covers, and housing components to separate the rotor.
2. Reassembling requires applying oil to seals and housing components before reinstalling them in reverse order.
3. For the swing motor, disconnecting hydraulic and electrical lines before removing bolts and lifting out the motor. Disassembly requires removing valves, seals and backup rings from the motor housing.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. It describes removing parts like seals, bolts, plates and pistons from the swivel and motor housing. Tools needed include wrenches, pullers, and lifting devices. Proper cleaning and marking of parts is emphasized to aid reassembly. Detailed illustrations accompany each step for reference.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil to seals before reassembling components in reverse order.
3. Draining swing motor oil before disconnecting hoses and removing bolts to lift out the motor.
4. Dismantling the swing motor involves removing springs, seals, pistons and other internal parts in a specific sequence.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil to seals before reassembling components in reverse order.
3. Draining swing motor oil before disconnecting hoses and removing bolts to lift out the motor.
4. Dismantling the swing motor involves removing springs, seals, pistons and other internal parts in a specific sequence.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and removing bolts and seals to separate the swivel housing, rotor, and cover.
2. Cleaning and reinstalling seals and components in reverse order for assembly.
3. Draining fluid, disconnecting hoses and bolts, and using lifting equipment to remove the swing motor.
4. Cleaning components and installing in reverse order for reinstallation.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...ufuusefjjsekkm
The document provides instructions for removing and installing a crankshaft front seal, front cover, and gear on a Caterpillar C4.4 engine. The procedures include using various tools to remove old components, cleaning surfaces, applying sealant, and torquing bolts to specifications. Detailed illustrations show the component locations and steps in the process.
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...fjjsekkmdmes
This document provides instructions for removing and installing a front cover and crankshaft front seal on a Caterpillar C4.4 engine. It describes the required tools and steps to remove and install the front cover and seal. The removal process involves removing mounting bolts and identifying bolt positions. Installation uses guide studs and alignment tools to correctly position the new front cover gasket and seal. Proper torque is applied to the mounting bolts.
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...fjsekskemmm
The document provides instructions for removing and installing a crankshaft front seal, front cover, and gear on a Caterpillar C4.4 engine. The procedures include using various tools to remove the old components, cleaning surfaces, applying sealant, positioning new components, and tightening bolts to specified torques.
Caterpillar Cat CS-663E, CP-663E Vibratory Compactor (Prefix DAG) Service Rep...8fusejkdmd9i
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3056E engine used in Caterpillar vibratory compactors. It describes removing mounting bolts from the top and sides of the housing and using lifting brackets and a suitable lifting device to remove the housing. Instructions are also given for cleaning parts, installing a new gasket if needed, and torquing mounting bolts to secure the housing.
The document provides instructions for removing and installing a front cover on a Caterpillar C4.4 engine. It describes:
1. Removing the crankshaft pulley and fan (if applicable) before removing the front cover.
2. Removing bolts and the front seal to detach the front cover from the front housing.
3. Cleaning surfaces and installing a new gasket before reattaching the front cover using alignment tools and torquing bolts to the specified value.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing housing on motor housing; installing seals, dowel pins, and coupling gear; installing ring gear; assembling two planetary carrier assemblies; installing carriers, gears, and shafts; assembling the transmission cover; and testing the duo-cone seals. The summary provides an overview of the major steps and components in the assembly process.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...guangkaic18147
The document provides instructions to disassemble a travel motor on a 390F L excavator. It lists 40 steps to remove components such as the head, relief valves, pistons, springs, seals, plates, and shaft. Tools required include a link bracket, slide hammer puller, threaded rod, pliers, driver group, and bolts. Precautions are provided to contain fluids, direct cleaning of parts, and release spring forces safely.
1) The document provides disassembly and assembly instructions for a final drive on an excavator.
2) It describes 32 steps to disassemble the final drive by removing components like housing covers, gears, shafts, and seals.
3) It describes 28 steps to reassemble the final drive by cleaning parts and reinstalling components like seals, bearings, gears, and housing pieces in the reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
The document provides step-by-step instructions to disassemble the final drive of a 323D2 excavator. It lists 28 steps to remove components like the cover, carrier assembly, ring gears, and seals. Special tools are required and components can weigh up to 312 kg. Cleanliness is important to prevent dirt entering during reassembly.
Caterpillar Cat 318D2 L Excavator (Prefix JEB) Service Repair Manual (JEB0000...guangkaic18147
The document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to remove parts like the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards like heavy component weights, pressurized hydraulic fluid, and released spring forces during the process. The goal is to fully disassemble the final drive to facilitate repair or replacement of internal parts.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...guangkaic18147
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and housing pieces.
3) The 31 steps for assembly describe installing seals, bearings, gears, and housing pieces in reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9S) Service Repair Manual (R9S000...guangkaic18147
This document provides instructions for disassembling and assembling the gear group of a Caterpillar 12M 2 motor grader. The disassembly procedure involves using various tools to remove 25 components of the gear group including gears, plates, seals, and housings. The assembly procedure lists the same 25 components and provides instructions for installing them in reverse order using the appropriate tools. Precautions are included to handle parts carefully and ensure proper alignment during assembly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil to seals before reassembling components in reverse order.
3. Draining swing motor oil before disconnecting hoses and removing bolts to lift out the motor.
4. Dismantling the swing motor involves removing springs, seals, pistons and other internal parts in a specific sequence.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and removing bolts and seals to separate the swivel housing, rotor, and cover.
2. Cleaning and reinstalling seals and components in reverse order for assembly.
3. Draining fluid, disconnecting hoses and bolts, and using lifting equipment to remove the swing motor.
4. Cleaning components and installing in reverse order for reinstallation.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...ufuusefjjsekkm
The document provides instructions for removing and installing a crankshaft front seal, front cover, and gear on a Caterpillar C4.4 engine. The procedures include using various tools to remove old components, cleaning surfaces, applying sealant, and torquing bolts to specifications. Detailed illustrations show the component locations and steps in the process.
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...fjjsekkmdmes
This document provides instructions for removing and installing a front cover and crankshaft front seal on a Caterpillar C4.4 engine. It describes the required tools and steps to remove and install the front cover and seal. The removal process involves removing mounting bolts and identifying bolt positions. Installation uses guide studs and alignment tools to correctly position the new front cover gasket and seal. Proper torque is applied to the mounting bolts.
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...fjsekskemmm
The document provides instructions for removing and installing a crankshaft front seal, front cover, and gear on a Caterpillar C4.4 engine. The procedures include using various tools to remove the old components, cleaning surfaces, applying sealant, positioning new components, and tightening bolts to specified torques.
Caterpillar Cat CS-663E, CP-663E Vibratory Compactor (Prefix DAG) Service Rep...8fusejkdmd9i
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3056E engine used in Caterpillar vibratory compactors. It describes removing mounting bolts from the top and sides of the housing and using lifting brackets and a suitable lifting device to remove the housing. Instructions are also given for cleaning parts, installing a new gasket if needed, and torquing mounting bolts to secure the housing.
The document provides instructions for removing and installing a front cover on a Caterpillar C4.4 engine. It describes:
1. Removing the crankshaft pulley and fan (if applicable) before removing the front cover.
2. Removing bolts and the front seal to detach the front cover from the front housing.
3. Cleaning surfaces and installing a new gasket before reattaching the front cover using alignment tools and torquing bolts to the specified value.
Similar to Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 and up).pdf (9)
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing housing on motor housing; installing seals, dowel pins, and coupling gear; installing ring gear; assembling two planetary carrier assemblies; installing carriers, gears, and shafts; assembling the transmission cover; and testing the duo-cone seals. The summary provides an overview of the major steps and components in the assembly process.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...guangkaic18147
The document provides instructions to disassemble a travel motor on a 390F L excavator. It lists 40 steps to remove components such as the head, relief valves, pistons, springs, seals, plates, and shaft. Tools required include a link bracket, slide hammer puller, threaded rod, pliers, driver group, and bolts. Precautions are provided to contain fluids, direct cleaning of parts, and release spring forces safely.
1) The document provides disassembly and assembly instructions for a final drive on an excavator.
2) It describes 32 steps to disassemble the final drive by removing components like housing covers, gears, shafts, and seals.
3) It describes 28 steps to reassemble the final drive by cleaning parts and reinstalling components like seals, bearings, gears, and housing pieces in the reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
The document provides step-by-step instructions to disassemble the final drive of a 323D2 excavator. It lists 28 steps to remove components like the cover, carrier assembly, ring gears, and seals. Special tools are required and components can weigh up to 312 kg. Cleanliness is important to prevent dirt entering during reassembly.
Caterpillar Cat 318D2 L Excavator (Prefix JEB) Service Repair Manual (JEB0000...guangkaic18147
The document provides instructions for disassembling the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to remove parts like the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards like heavy component weights, pressurized hydraulic fluid, and released spring forces during the process. The goal is to fully disassemble the final drive to facilitate repair or replacement of internal parts.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...guangkaic18147
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and housing pieces.
3) The 31 steps for assembly describe installing seals, bearings, gears, and housing pieces in reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
Caterpillar Cat 12M 2 MOTOR GRADER (Prefix R9S) Service Repair Manual (R9S000...guangkaic18147
This document provides instructions for disassembling and assembling the gear group of a Caterpillar 12M 2 motor grader. The disassembly procedure involves using various tools to remove 25 components of the gear group including gears, plates, seals, and housings. The assembly procedure lists the same 25 components and provides instructions for installing them in reverse order using the appropriate tools. Precautions are included to handle parts carefully and ensure proper alignment during assembly.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Digital Fleet Management - Why Your Business Need It?
Caterpillar Cat 538 EXCAVATOR (Prefix KBJ) Service Repair Manual (KBJ00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 538 EXCAVATOR KBJ
Configuration: 538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
538 LL GF Forest Machine Machine Systems
Media Number -M0071454-01 Publication Date -01/08/2017 Date Updated -02/08/2017
i06724515
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3940 Bracket As 2
Start By:
a. Remove the swivel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put orientation and location marks on housings for installation purposes.
1. Thoroughly clean the outside of the swivel prior to disassembly.
1/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
2. Illustration 1 g01767936
2. Attach Tooling (B) and a suitable lifting device to swivel (1). The weight of swivel (1) is
approximately 496 kg (225 lb).
3. Position swivel (1) onto Tooling (A).
Illustration 2 g01768234
4. Remove bolts (2) and (3).
5. Remove cover (4) from the bottom of swivel (1).
Illustration 3 g01768296
2/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 6. Remove O-ring seal (5), bolts (6), and retainer (7) from the bottom of swivel (1).
Illustration 4 g01768395
Illustration 5 g01768497
Note: Be sure that alignment marks are put on rotor (8) and housing (11) for assembly
purposes.
7. Use Tooling (B) and a suitable lifting device to separate rotor (8) from housing (9).
8. Remove O-ring seal (10) (not shown) from housing (11).
9. Use Tooling (B) and a suitable lifting device to separate rotor (8) from housing (11).
3/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 6 g06092449
10. Remove seal assemblies (12) from housing (11).
Illustration 7 g06092455
11. Remove seal assemblies (13) from housing (9).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 20:43:01 UTC+0800 2021
4/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 538 EXCAVATOR KBJ
Configuration: 538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
538 LL GF Forest Machine Machine Systems
Media Number -M0071454-01 Publication Date -01/08/2017 Date Updated -02/08/2017
i06724539
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3940 Bracket As 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals and the seals for wear or for damage. Replace the components, if
necessary.
1/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 1 g01768813
1. Apply clean hydraulic oil to seal assemblies (12).
2. Install O-ring seal (10) and seal assemblies (12) into housing (11).
Illustration 2 g01768833
3. Position housing (9) onto housing (11). Loosely install bolts (2) to secure housing (9) to
housing (11).
4. Apply clean hydraulic oil to seal assemblies (13).
5. Install seal assemblies (13) into housing (9).
2/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 3 g01769453
6. Use two people to position housing (9) and housing (11) onto Tooling (A). The combined
weight of housing (9) and housing (11) is approximately 41 kg (91 lb).
Illustration 4 g01769537
7. Attach Tooling (B) and a suitable lifting device to rotor (8). The weight of rotor (8) is
approximately 54 kg (119 lb).
8. Use Tooling (B) and a suitable lifting device to install rotor (8) into housing (11) and
housing (9) (not shown).
9. Remove four bolts (2) (not shown).
3/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 5 g01768296
10. Install retainer (7), bolts (6), and O-ring seal (5) to the bottom of swivel (1).
Illustration 6 g01768234
11. Install cover (4), bolts (3), and bolts (2) to the bottom of swivel (1).
End By:
a. Install the swivel.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 20:43:56 UTC+0800 2021
4/4
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 538 EXCAVATOR KBJ
Configuration: 538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
538 LL GF Forest Machine Machine Systems
Media Number -M0071454-01 Publication Date -01/08/2017 Date Updated -02/08/2017
i06725205
Swing Motor - Remove and Install
SMCS - 5058-010-ZW
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 439-3938 Link Bracket 2
Start By:
a. Release the hydraulic system pressure.
Illustration 1 g01714793
1. Remove guard assembly (1).
1/5
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 2 g06092676
2. Remove sheet (2) and cover assembly (3).
Illustration 3 g06092691
3. Remove cover assembly (4).
Illustration 4 g01715574
Typical Example
2/5
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 4. Install Tooling (A) onto the hydraulic tank . Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull a vacuum on the
hydraulic system.
5. Drain the swing drive oil. Refer to Operation and Maintenance Manual, "Swing Drive Oil -
Change" for the correct draining and filling procedures.
Illustration 5 g01715674
Note: Not all machines will require the removal of all the hose assemblies. Remove the
hose assemblies that will make the removal of the swing motor easier.
6. Disconnect hose assemblies (12) and (13) at the boom side of the hose assemblies.
Reposition hose assemblies (12) and (13) out of the way for more access to the swing
motor.
7. Disconnect hose assemblies (6) and (7).
8. Disconnect hose assemblies (8) and (9).
9. Disconnect harness assembly (10).
10. Disconnect clip (11).
3/5
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 6 g01715876
11. Disconnect hose assembly (14).
Illustration 7 g01715880
12. Remove bolts (16) and anti-reaction valve (17).
13. Remove bolts (15).
14. Prior to the removal of the swing motor, clean the swing motor and the area around the
swing motor. Remove any loose paint around the mating surface of the swing drive and the
swing motor to prevent contamination from entering the swing drive.
Illustration 8 g01715956
15. Attach Tooling (B) and a suitable lifting device to swing motor (18). The weight of swing
motor (18) is approximately 55 kg (120 lb).
16. Remove swing motor (18).
Installation Procedure
1. Install swing motor (18) in the reverse order of removal.
4/5
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 538 EXCAVATOR KBJ
Configuration: 538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
538 LL GF Forest Machine Machine Systems
Media Number -M0071454-01 Publication Date -01/08/2017 Date Updated -02/08/2017
i06726429
Swing Motor - Disassemble
SMCS - 5058-015-ZW
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-0651 Bolts 2
8T-4167 Hard Washers 2
B 1P-1859 Retaining Ring Pliers 1
C 9S-9152 Bearing Puller Gp 1
D
1P-0074 Slide Hammer Puller 1
5F-7344 Puller Block 1
5P-4750 Adjusting Screw 1
7S-7786 Puller Leg 2
Start By:
a. Remove the swing motor.
1/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g00704611
1. If necessary, remove bolts (2) and anti-reaction valve (3) from head (1).
2. Remove mounting bolts (4).
Illustration 2 g00704621
3. Remove dipstick tube (5) and breather tube (6) from motor housing (7).
Illustration 3 g00704704
4. Remove relief valves (8).
2/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 4 g00704710
5. Remove O-ring seals (10), (12), and (13).
6. Remove backup rings (9) and (11).
Illustration 5 g00704719
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. 7. Remove bolts (14) and the head.
Illustration 6 g00704734
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (18), O-ring seal (17), spring (16), and spool valve (15) from the head. Repeat
for the other side.
Illustration 7 g00704741
9. Remove adapter (19), fitting (20), and plugs (21).
4/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 8 g00704743
10. Remove O-ring seal (22) from plug (21).
Illustration 9 g00704749
11. Remove O-ring seals (23) and (24) from fittings (19) and (20).
Illustration 10 g00704754
12. Remove O-ring seal (25).
5/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 11 g00704771
13. Remove spring pins (26) and bearing (27).
Illustration 12 g00704796
14. Remove springs (28) and port plate (29).
Illustration 13 g01021864
Typical Example
15. Install Tooling (A) and apply air pressure to unseat the piston.
Note: Use air pressure to avoid damage to the piston.
6/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 14 g01021875
16. Remove piston (30).
Illustration 15 g01022038
Typical Example
17. Remove plates (31).
Illustration 16 g01021889
Typical Example
18. Remove barrel (32) and the pistons as an assembly.
7/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 17 g01021898
19. Mark pistons (33).
20. Remove pistons (33) from barrel (32).
Illustration 18 g01021903
21. Remove pistons (33) from plates (34) and (35).
Illustration 19 g01021909
22. Separate plates (34) and (35).
8/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 20 g01021919
Typical Example
23. Remove O-ring seals (36) and (36a) from the motor housing.
Illustration 21 g00705209
24. Remove swashplate (37).
Illustration 22 g00705222
25. Use Tooling (B) to remove retaining ring (38) from shaft (39).
9/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 23 g00705258
26. Remove shaft (39).
Illustration 24 g00705277
27. Use a suitable press and Tooling (C) to remove bearing race (40).
Illustration 25 g00705284
28. Use a suitable press and Tooling (C) to remove bearing race (41).
10/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY ...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 26 g01022013
Typical Example
Illustration 27 g00705295
29. Use Tooling (D) to remove bearing (42).
Illustration 28 g00705441
30. Remove lip seal (43).
11/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY ...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 29 g00705442
31. Remove fitting (44).
Illustration 30 g00705445
32. Remove O-ring seal (45) from fitting (44).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 20:45:48 UTC+0800 2021
12/12
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY ...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 538 EXCAVATOR KBJ
Configuration: 538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
538 LL GF Forest Machine Machine Systems
Media Number -M0071454-01 Publication Date -01/08/2017 Date Updated -02/08/2017
i06727706
Swing Motor - Assemble
SMCS - 5058-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1859 Retaining Ring Pliers 1
E 1P-0510 Driver Group 1
F 369-9451 Grease -
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring seal. Use Tooling (F) during the assembly procedure.
Note: Apply a light film of clean hydraulic oil to all components before assembly.
1/13
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 1 g00705445
1. Install O-ring seal (45) onto fitting (44).
Illustration 2 g00705442
2. Install fitting (44).
Illustration 3 g00705441
3. Lubricate lip seal (43) with clean hydraulic oil. Install lip seal (43) with the lip toward the
inside of the motor housing.
2/13
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
30. Illustration 4 g01022013
Typical Example
Illustration 5 g01287176
4. Use Tooling (E) to install bearing (42).
Illustration 6 g00705595
5. Raise the temperature of bearing race (41). Install bearing race (41).
3/13
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Illustration 7 g00705592
6. Raise the temperature of bearing race (40). Install bearing race (40).
Illustration 8 g00705597
Illustration 9 g00705258
7. Install shrink wrap tubing onto shaft (39). The shrink wrap tubing will protect the seal
during installation of shaft (39).
8. Install shaft (39).
4/13
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. Illustration 10 g00705602
9. Use Tooling (B) to install retaining ring (38) onto shaft (39). Remove the shrink wrap
tubing.
Illustration 11 g00705209
10. Install swashplate (37).
Illustration 12 g01021919
Typical Example
11. Install O-ring seals (36) and (36a) into the motor housing.
5/13
538 Forest Machine General Forestry KBJ00001-UP (MACHINE) POWERED BY C7...
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...