Caterpillar cat 962 h wheel loader (prefix ssa) service repair manual (ssa00001 and up)

Service Repair Manual
Models
962H WHEEL LOADER

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962H WHEEL LOADER SSA
Configuration: 962H Wheel Loader SSA00001-UP (MACHINE) POWERED BY C7.2 Engine
Disassembly and Assembly
950H and 962H Wheel Loaders Power train
Media Number -UENR0789-00 Publication Date -01/10/2012 Date Updated -30/10/2012
i05018380
Torque Converter (Lockup) - Assemble
SMCS - 3101-016-L7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/11962H Wheel Loader SSA00001-UP (MACHINE) POWERED BY C7.2 Engine(SEBP...
2020/4/1https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

Illustration 1 g03211726
1. If necessary, install locating dowel (42) .
2. Install bearing (43) so that the notch in bearing (43) is in alignment with locating dowel
(42) .
3. Install turbine (40) to hub (41) and install bolts (39). Tighten bolts (39) to a torque of 60 ± 7
N·m (44 ± 5 lb ft).
4. Install turbine assembly (38) into the impeller housing.

5. Install spacer (36) and O-ring seal (37) .
6. Use Tooling (C) to install retaining ring (35) .
7. Install cover (33), retaining ring (32), and ring (31) on housing (34) .

8. If necessary, install locating dowel (30) .
9. Install seal ring (29) on carrier shaft (23) .
10. Install bearing (28) in impeller (21) .

11. Install drive gear (27) and bolts (26). Tighten bolts (26) to a torque of 105 ± 15 N·m (77 ±
11 lb ft).
12. Use a suitable press to install carrier shaft (23) in impeller (21) .
13. Install spacer (25) on impeller (21) .

14. Install stator (24) and retaining ring (22) on to carrier shaft (23) and impeller (21) .
15. Install impeller (21) and bolts (20). Tighten bolts (20) to a torque of 60 ± 7 N·m (44 ± 5 lb
ft).

16. Install bearing (19) on output shaft (17) .
17. Install seal ring (18) .
18. Install output shaft (17) and retaining ring (16) .
19. Install drive gear (15) .

20. Use Tooling (A) and a suitable lifting device to install the torque converter housing over the
torque converter assembly. The weight of the torque converter housing is approximately
113 kg (250 lb).
21. Install bolts (7). Tighten bolts (7) to a torque of 60 ± 7 N·m (44 ± 5 lb ft).
22. Install bearing (14) and drive gear shaft (12) in pump drive gear (13) .
23. Use Tooling (B) to install pump drive gear (13) into the housing.

24. Install bolt (11) on drive gear shaft (12). Tighten bolt (11) to a torque of 105 ± 20 N·m (77 ±
15 lb ft).
25. Install pump drive flange (10) and bolts (9). Tighten bolts (9) to a torque of 60 ± 7 N·m (44
± 5 lb ft).

26. Install torque converter speed sensor (8). Adjust torque converter speed sensor (8) in order
to maintain an air gap of 0.71 ± 0.18 mm (0.028 ± 0.007 inch). Tighten torque converter
speed sensor (8) to a torque of 25 ± 5 N·m (18 ± 4 lb ft).
27. Install washer (6) and bolt (5). Tighten bolt (5 ) to a torque of 105 ± 20 N·m (77 ± 15 lb ft).
10/11962H Wheel Loader SSA00001-UP (MACHINE) POWERED BY C7.2 Engine(SE...

28. Install torque converter inlet relief valve (4) and the O-ring seal.
29. Install transmission hydraulic control relief valve (3) and bolts (2) to torque converter
housing (1) .
End By: Connect the torque converter to the transmission and to the output transfer gears.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 1 19:28:34 UTC+0800 2020

Shutdown SIS
Previous Screen
i05018810
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Start By:
A. Separate the torque converter from the transmission and output transfer gears.
Note: Cleanliness is an important factor. Thoroughly clean the exterior of the component before
the disassembly procedure. Cleaning will help to prevent dirt from entering the internal
mechanism.

1. Disconnect harness assemblies (1) .
2. Remove tube assembly (2) .
3. Attach Tooling (A) and a suitable lifting device to transmission (3). The weight of
transmission (3) is approximately 363 kg (800 lb).

4. Remove transmission (3) from output transfer gears (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 1 19:29:29 UTC+0800 2020

Shutdown SIS
Previous Screen
i05018793
Transmission Planetary - Disassemble
SMCS - 3160-015
Disassembly Procedure
Table 1
Required Tools
B 1P-2420 Transmission Repair Stand 1
C 136-1452 Retaining Ring Pliers As 1
D 5P-5197 Retaining Ring Pliers As 1
E 1P-1863 Retaining Ring Pliers As 1
F 1P-0520 Driver Gp 1
G 8B-7551 Bearing Puller Gp 1
Start By:
A. Separate the torque converter from the transmission.

1. Remove O-ring seals (1) and (5) from the housing.
2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft.
3. Use Tooling (A) and a suitable lifting device to position the transmission on Tooling (B), as
shown.

4. Use Tooling (C) to remove retaining ring (8) from output shaft (7) .
5. Remove four bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolt.
6. Remove clutch piston (10) from No. 6 clutch housing (6) .
7. Remove seal rings (11) and (12) from clutch piston (10) .

8. Remove upper clutch plate (13) and remove springs (14) and remove reaction dowels (15) .
9. Remove clutch plates (16) and friction discs (17) .

10. Remove ring gear (18) and remove O-ring seal (19) .
11. Remove carrier assembly (20) .

12. Remove metal seal ring (21) from the carrier assembly.
13. Use a suitable hammer and a punch to push the spring pins through carrier assembly (20)
and into planetary shafts (22) .
14. Use a suitable hammer and a punch to remove planetary shafts (22) from carrier assembly
(20) .

15. Remove thrust discs (23), and remove planetary gears (25), and remove bearings (24) from
the carrier assembly. Remove the spring pins from planetary shafts (22) .
16. Use Tooling (D) to remove retaining ring (26) from the output shaft.

17. Use Tooling (E) to remove retaining ring (27) from the output shaft.
18. Use Tooling (A) and a suitable lifting device to remove housing (28) and the O-ring seal.
The weight of housing (28) is approximately 29 kg (64 lb).
19. Remove retaining ring (30) and bearing (29) from housing (28) .

20. Remove friction discs (31) and clutch plates (32) and remove the springs.
21. Use Tooling (C) to compress retaining ring (33). Remove clutch housing (35) from ring
gear (34) .

22. Use Tooling (C) to remove retaining ring (33) from clutch housing (35) .
23. Use steel spacers and a press to apply pressure to retainer plate (36). Remove retaining ring
(37) from the clutch housing.
24. Remove retainer plate (36) from sun gear shaft (39). Remove disc springs (38) from clutch
housing (35) .
25. Remove clutch housing (35) from sun gear shaft (39) .

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

26. Remove seal rings (40) and piston (41) from the clutch housing.
27. Remove seal ring (42) and seal ring (43) from piston (41) .
28. Remove retaining ring (44) from the output shaft.

29. Remove sun gear (45) and springs (46) .
30. Remove friction discs (47) and clutch plates (48) .

Caterpillar cat 962 h wheel loader (prefix ssa) service repair manual (ssa00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (6)

Similar to Caterpillar cat 962 h wheel loader (prefix ssa) service repair manual (ssa00001 and up)

Similar to Caterpillar cat 962 h wheel loader (prefix ssa) service repair manual (ssa00001 and up) (20)

More from fujsjejfkskemm

More from fujsjejfkskemm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 962 h wheel loader (prefix ssa) service repair manual (ssa00001 and up)