Caterpillar cat 160 h motor grader (prefix xzk) service repair manual (xzk00001 and up)

Service Repair Manual
Models
160H Motor Grader

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 160H MOTOR GRADER XZK
Configuration: 160H Motor Grader XZK00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02107004
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
A. Remove the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3160H Motor Grader XZK00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2019/12/1https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00476414
1. Remove bolts (1), plate (2), and fuel pump idler gear (3) .
2. Remove the bearing from fuel pump idler gear (3) with Tooling (A) .
3. Remove bolts (4), plate (5), and camshaft gear (6) .

4. Remove the bolts that hold shield (7) in position between the fuel pump and the exhaust
manifold. Slide the shield backward from the timing cover plate.
5. Remove nuts (8) .
6. Remove bolts (10). Remove timing gear plate (9) and the gasket.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 1 15:22:40 UTC+0800 2019

Shutdown SIS
Previous Screen
i02107019
Gear Group (Front) - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
A 1P-0510 Driver Group 1
B 9S-3263 Thread Lock Compound 1
NOTICE
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets or the O-ring
seals are worn or damaged, use new parts for replacement.
1. Clean the old gasket from the contact surfaces of the timing gear plate and the cylinder
block. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face
of the cylinder block.

NOTICE
The bolts that hold the timing gear plate in position on the cylinder
block should have a reduced bolt head thickness. The reduced bolt
head thickness is needed for clearance for the gears.
2. Ensure that the O-ring seals are in position on the end of the fuel injection pump housing.
Put timing gear plate (9) in position on the cylinder block. Install bolts (10) .
3. Install shield (7). Install nuts (8) .
Note: After the timing gear plate is installed, ensure that the rack is free to move in the fuel
injection pump housing. The O-ring seal on the drive end of the fuel injection pump housing
can hold the rack. This can help prevent free rack movement. Rack movement can be seen
through a hole in the timing gear plate just above the mounting of the fuel pump gear. If the
rack does not move freely, remove the timing gear plate and check the O-ring seal on the
drive end of the fuel injection pump housing.

If the rack does not move freely, the engine can over speed and be
damaged. Serious personal injury may result.
Note: If idler gear shaft (11) for the fuel pump idler gear was removed, use Tooling (B) on
the threads of bolts (12) and nut (13) before reinstalling idler gear shaft (11). Tighten bolts
(12) and nut (13) to a torque of 50 � 10 N�m (37 � 7 lb ft).
4. Put camshaft gear (6) and plate (5) in position on the engine. Align the Mark "C" on the
camshaft gear with the Mark "C" on the crankshaft gear. Install bolts (4) and tighten bolts
(4) to a torque of 55 � 7 N�m (41 � 5 lb ft).
5. Use Tooling (A) in order to install the bearing in fuel pump idler gear (3). The end of the
bearing must be 3.00 � 0.25 mm (.118 � .010 inch) below the face of the hub of the fuel
pump idler gear.

6. Ensure that the oil hole in the shaft for fuel pump idler gear (3) is open. Install fuel pump
idler gear (3). Put plate (2) in position with the finished side facing toward fuel pump idler
gear (3). Apply Tooling (B) on bolts (1). Install bolts (1) that hold fuel pump idler gear (3)
in position.
Note: Remove excess Tooling (B) on plate (2). Excess Tooling (B) on plate (2) may flow
into the gear bearings. This condition can affect lubrication. Bearing life can also be
affected.
End By: Install the automatic timing advance unit. Refer to Disassembly and Assembly,
"Automatic Timing Advance - Install".
Sun Dec 1 15:23:35 UTC+0800 2019

Shutdown SIS
Previous Screen
i02107163
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
B. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.

1. Remove the bolts that hold the oil pan and the oil pan plate to the front housing. Loosen the
remaining bolts that hold the oil pan in position. Put spacers between the cylinder block and
the oil pan plate. This must be done in order to prevent damage to the gasket for the oil pan
plate.
Note: If the gasket for the oil pan plate is damaged, the oil pan plate must be removed.
Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
2. Remove covers (1) and (2) from the back of the front plate.
3. Remove all bolts (3) that hold front housing (4) in position on the engine. Remove front
housing (4) and the gasket from the engine.
Sun Dec 1 15:24:31 UTC+0800 2019

Shutdown SIS
Previous Screen
i02107191
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
A 3S-6252 Sealant 1
NOTICE

1. Put the gasket and front housing (4) in position on the engine. Install all bolts (3) that hold
the front housing to the engine. Tighten bolts (5) to a torque of 23 � 4 N�m (17 � 3 lb ft).
2. Put the gasket and cover (1) in position and install the bolts that fasten cover (1) to the front
plate. Put the O-ring seal and cover (2) in position and install the bolts that fasten cover (2)
to the front plate.
3. Trim the front housing gasket so the gasket is even with the bottom of the cylinder block.
Note: If the oil pan plate was removed, install a new gasket and install the oil pan plate.
Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
4. Apply Tooling (A) to the bottom surface of the front housing gasket. Remove the spacers
that were installed between the cylinder block and the oil pan plate. Install the bolts that
hold the oil pan and the oil pan plate to the front housing. Tighten the remaining bolts that
hold the oil pan in position.
Sun Dec 1 15:25:27 UTC+0800 2019

Shutdown SIS
Previous Screen
i04880697
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
3304B Removal Procedure
NOTICE
1. Loosen hose clamp (5) and remove the hose from breather cap (3) .
2. Remove bolt (1) and remove breather cap (3) .

3. Remove bolts (4) and the washers that hold valve mechanism cover (2) in position. Remove
valve mechanism cover (2) and the gasket.
3306B Removal Procedure
NOTICE
1. Remove bolt (1) and breather cap (3) from valve mechanism cover (2) . Remove the O-ring
seal from breather cap (3) .
2. Remove bolts (4) and the washers that hold valve mechanism cover (2) in position. Remove
valve mechanism cover (2) and the gasket.
3304B Installation Procedure
NOTICE

Note: Check the condition of the gasket. If the gasket is worn or damaged, use new parts for
replacement.
1. Install a new gasket for valve mechanism cover (2) . Apply 5H-2471 Adhesive on the
surfaces of the gasket and valve mechanism cover (2) . Place valve mechanism cover (2) in
position on the cylinder head.
2. Install bolts (4) that hold valve mechanism cover (2) . Tighten the bolts in a numerical
sequence to a torque of 16 � 3 N�m (12 � 2 lb ft).
3. Install the hose on breather cap (3) and tighten hose clamp (5) .
3306B Installation Procedure
NOTICE
Note: Check the condition of the gasket and O-ring seals. If the gasket or the O-ring seals
are worn or damaged, use new parts for replacement.
1. Install a new gasket for valve mechanism cover (2) . Put valve mechanism cover (2) in
position on the cylinder head.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2. Install the washers and bolts (4) that hold valve mechanism cover (2) in position. Tighten
the bolts in a numerical sequence to a torque of 16 � 3 N�m (12 � 2 lb ft). Use the numerical
sequence that is shown in illustration 7.
3. Put the O-ring seal and breather cap (3) in position. Install the washer and bolt (1) . Tighten
bolt (1) to a torque of 14 � 3 N�m (10 � 2 lb ft).
Sun Dec 1 15:26:22 UTC+0800 2019

Shutdown SIS
Previous Screen
i00921540
Compression Brake - Remove
SMCS - 1119-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE

1. Remove four bolts (1). Disconnect wires (2) and (3) .
2. Remove Compression Brake (A) by lifting Compression Brake (A) with one hand. Remove
Compression Brake (A) while you hold oil tube (4) in order to ensure that oil tube (4) does
not come out of Compression Brake (B) .
3. Remove Compression Brake (B) .
Sun Dec 1 15:27:18 UTC+0800 2019

Shutdown SIS
Previous Screen
i00921740
Compression Brake - Disassemble
SMCS - 1119-015
Disassembly Procedure
Start By:
A. Remove the Compression Brake. Refer to Disassembly and Assembly, "Compression Brake
- Remove".
NOTICE

Caterpillar cat 160 h motor grader (prefix xzk) service repair manual (xzk00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

Similar to Caterpillar cat 160 h motor grader (prefix xzk) service repair manual (xzk00001 and up)

Similar to Caterpillar cat 160 h motor grader (prefix xzk) service repair manual (xzk00001 and up) (7)

More from fjskexswksemmm

More from fjskexswksemmm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 160 h motor grader (prefix xzk) service repair manual (xzk00001 and up)