The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a Caterpillar 3046 engine. The removal process involves using tools to lift components, then removing bolts and seals. The installation process specifies cleaning surfaces, applying oil, and using tools to correctly position new seals before tightening bolts and checking installation. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 438 c backhoe loader (prefix 2dr) service repair manual (2dr0...udfjjjskekdme
This document provides instructions for removing and installing an air conditioner compressor group, air conditioner filter, full air conditioner system, and cab from a Caterpillar 438C backhoe loader. It describes disconnecting wiring, removing mounting hardware, and reversing steps for installation. Safety warnings are provided regarding working on pressurized air conditioning systems and containing fluids when working on the machine.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 933 c hystat track loader (prefix 4ms) service repair manual ...fujskekfmsme
The document provides instructions for installing and removing an air inlet manifold and valves on a Caterpillar 3046 engine. It describes:
1) Using various tools to compress valve springs and remove caps and keepers to access the valves and springs.
2) Checking valve springs with a spring tester and specifications.
3) Installing new gaskets and bolting the air inlet manifold, elbow, and other components in multiple steps while checking for damage.
4) Maintaining air pressure in cylinders during valve spring removal and installation to hold valves in position.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...pfiskdmjekm
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair. Tools required are listed for each procedure.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 428 f backhoe loader (prefix lbh) service repair manual (lbh0...fujsekwsxksmem
The document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a 428F backhoe loader with a C4.4 engine. It describes removing the old crankshaft rear seal using a Torx socket and installing the new seal assembly dry. It also details removing the flywheel housing bolts and dowels, checking the crankshaft rear seal for leaks, and reinstalling the housing using guide studs to align it. Proper torque values are specified for the fasteners. Additionally, the document gives directions for removing and installing the crankshaft pulley on engines both with and without an automatic belt tensioner.
The document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing the fuel transfer pump from a Caterpillar 3306 engine. The procedures include:
- Turning off the fuel supply and disconnecting tubes and hoses
- Removing bolts and washers securing components and lifting parts off
- Checking condition of gaskets and installing new ones if needed
- Reinstalling components by securing with bolts and reconnecting tubes and hoses
The instructions emphasize cleaning parts and containing fluids during disassembly and reinstallation.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel using a lifting device and removing bolts, then removing the flywheel ring gear if necessary.
2) Installing the flywheel ring gear if it was removed by heating it and positioning it on the flywheel, then installing the flywheel using bolts and a lifting device.
3) Removing the crankshaft rear seal by removing housing bolts and pulling out the seal, gasket and housing.
4) Installing the new crankshaft rear seal using a installer tool and pressing the seal
Caterpillar cat 438 c backhoe loader (prefix 2dr) service repair manual (2dr0...udfjjjskekdme
This document provides instructions for removing and installing an air conditioner compressor group, air conditioner filter, full air conditioner system, and cab from a Caterpillar 438C backhoe loader. It describes disconnecting wiring, removing mounting hardware, and reversing steps for installation. Safety warnings are provided regarding working on pressurized air conditioning systems and containing fluids when working on the machine.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 933 c hystat track loader (prefix 4ms) service repair manual ...fujskekfmsme
The document provides instructions for installing and removing an air inlet manifold and valves on a Caterpillar 3046 engine. It describes:
1) Using various tools to compress valve springs and remove caps and keepers to access the valves and springs.
2) Checking valve springs with a spring tester and specifications.
3) Installing new gaskets and bolting the air inlet manifold, elbow, and other components in multiple steps while checking for damage.
4) Maintaining air pressure in cylinders during valve spring removal and installation to hold valves in position.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...pfiskdmjekm
This service manual document provides instructions for repairing and servicing excavator models 336D2 and 336D2 L. It includes procedures for removing and installing valve guides, valve seat inserts, the engine oil filter base, and oil cooler. Technicians are advised to keep parts clean and contain fluids during repair. Tools required are listed for each procedure.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 428 f backhoe loader (prefix lbh) service repair manual (lbh0...fujsekwsxksmem
The document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a 428F backhoe loader with a C4.4 engine. It describes removing the old crankshaft rear seal using a Torx socket and installing the new seal assembly dry. It also details removing the flywheel housing bolts and dowels, checking the crankshaft rear seal for leaks, and reinstalling the housing using guide studs to align it. Proper torque values are specified for the fasteners. Additionally, the document gives directions for removing and installing the crankshaft pulley on engines both with and without an automatic belt tensioner.
The document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing the fuel transfer pump from a Caterpillar 3306 engine. The procedures include:
- Turning off the fuel supply and disconnecting tubes and hoses
- Removing bolts and washers securing components and lifting parts off
- Checking condition of gaskets and installing new ones if needed
- Reinstalling components by securing with bolts and reconnecting tubes and hoses
The instructions emphasize cleaning parts and containing fluids during disassembly and reinstallation.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel using a lifting device and removing bolts, then removing the flywheel ring gear if necessary.
2) Installing the flywheel ring gear if it was removed by heating it and positioning it on the flywheel, then installing the flywheel using bolts and a lifting device.
3) Removing the crankshaft rear seal by removing housing bolts and pulling out the seal, gasket and housing.
4) Installing the new crankshaft rear seal using a installer tool and pressing the seal
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jdjkskmikdkmd
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jdjkskmikdkmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...paws21610697
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...paws21610697
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...cdfvvv1
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fikkskmmdm
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...cdfvvv1
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...uddksemd8ud
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...uddksemd8ud
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...f7djidksmd3e
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
More Related Content
Similar to Caterpillar cat 315 b track type excavator (prefix 3aw) service repair manual (3aw00001 and up)
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jdjkskmikdkmd
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...jdjkskmikdkmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...paws21610697
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...paws21610697
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...cdfvvv1
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fikkskmmdm
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...cdfvvv1
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...uddksemd8ud
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar Cat 318B L Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...uddksemd8ud
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
The document provides instructions for removing and installing the flywheel housing on a 3046 engine for Caterpillar 318B L and 318B LN excavators. The removal procedure involves using a lifting device and bracket to remove the flywheel housing which is secured by 12 bolts. The installation procedure specifies cleaning surfaces, installing a new gasket, and securing the flywheel housing with 12 bolts.
Caterpillar Cat 318B N Excavator (Prefix 7KZ) Service Repair Manual (7KZ00001...f7djidksmd3e
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Similar to Caterpillar cat 315 b track type excavator (prefix 3aw) service repair manual (3aw00001 and up) (20)
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646268
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00527024
1. Install Tool (A), a strap, and a suitable lifting device onto flywheel (2) .
2. Remove six bolts (1) that secure flywheel (2) from the crankshaft.
3. Remove flywheel (2). The weight of the flywheel is 50 kg (110 lb).
Note: Dowel pin hole (3) is slightly offset in order to ensure correct installation.
4. Check the condition of the dowels (not shown). If the dowels are damaged, use new parts
for replacement.
Illustration 2 g00527069
5. Check the condition of the ring gear (4). Replace the ring gear with a new part if the gear is
worn or damaged.
6. Place flywheel (2) and ring gear (4) on a suitable support.
Note: Identify the orientation of the ring gear on the flywheel for the correct positioning
when the new ring gear is installed.
7. Use a hammer and a punch in order to remove ring gear (4) from the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:02:36 UTC+0800 2020
2/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646270
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Use an oven and heat ring gear (2) to a maximum temperature of 150 °C (302 °F). Install
the ring gear.
1/3
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00562859
2. Position the ring gear (4) on flywheel (2) .
Illustration 2 g00527024
3. Check the condition of the dowels (not shown). If the dowels are damaged, use new parts
for replacement.
4. Install Tool (A), a strap, and a suitable lifting device onto flywheel (2) .
5. Install flywheel (2). The weight of the flywheel is 50 kg (110 lb).
Note: Dowel pin hole (3) is slightly offset in order to ensure correct installation.
6. Install six bolts (1) in order to secure flywheel (2) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
7. Remove Tool (A) .
8. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for more
information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Nov 9 15:03:32 UTC+0800 2020
2/3
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i05485410
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller Gp 1
Start By:
A. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00527955
1. Drill three evenly spaced 3 mm (.12 inch) holes in crankshaft rear seal (1) .
2. Use Tool (A) in order to remove the crankshaft rear seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:04:28 UTC+0800 2020
2/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i05485391
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 438-3244 Oil Seal Installer 1
B 438-3245 Seal Adapter 1
C 6V-3303 Bolt 1
D 4B-5275 Washer 1
E 9U-6172 Bolt 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft rear seal.
1/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00528113
2. Position Tooling (B) onto the crankshaft and install Tooling (E) .
Note: Be sure that Tooling (B) is correctly aligned with the crankshaft.
3. Put new crankshaft rear seal (1) in Tooling (A) .
4. Install Tooling (C) , Tooling (D) , and Tooling (A) on Tooling (B) .
5. Push crankshaft rear seal (1) onto the crankshaft until Tooling (A) bottoms out.
6. Remove the tooling from the crankshaft. Check the crankshaft rear seal for correct
installation.
End By: Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:05:23 UTC+0800 2020
2/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646275
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 135-7575 Link Bracket 1
Start By:
A. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
B. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00528388
1. Install Tool (A), a strap, and a suitable lifting device onto flywheel housing (1) .
2. Remove twelve bolts (2) and the washers that secure flywheel housing (1) to the cylinder
block.
3. Remove flywheel housing (1). The weight of the flywheel is 30 kg (66 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g00528389
1. Check the condition of two dowels (4). If dowels (4) are damaged, use new parts for
replacement.
2. Clean old gasket material (3) from the surfaces of the cylinder block and the flywheel
housing that contact each other. Install a new gasket on the cylinder block (not shown).
Illustration 3 g00528388
3. Install flywheel housing (1) .
4. Install the washers and twelve bolts (2) in order to secure flywheel housing (3) to the
cylinder block.
5. Remove Tool (A) .
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal -
Install".
Mon Nov 9 15:06:19 UTC+0800 2020
3/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646277
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-9120 Socket (1) 1
is
B 1P-2321 Combination Puller 1
( 1 )
Tool (A) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00528749
1. Remove six bolts (1) and the washers from vibration damper (2). Remove vibration damper
(2) from crankshaft pulley (5) .
Note: Inspect the vibration damper for leaks and dents. If either condition exists, replace the
vibration damper with a new part.
2.
Illustration 2 g00559259
3. Use Tool (A) and remove nut (3) and the washer from the crankshaft.
2/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00559308
4. If necessary, use Tool (B) and remove crankshaft pulley (5) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00559259
1. Install crankshaft pulley (5) with the washer and nut (3) onto crankshaft (4) .
2. Use Tool (A) to tighten nut (3) to a torque of 490 ± 10 N·m (360 ± 7 lb ft). Hit nut (3) with
a hammer and torque the bolt again to 490 ± 10 N·m (360 ± 7 lb ft).
3/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g00528749
3. Use six bolts (1) and the washers in order to install vibration damper (2) on the crankshaft
pulley.
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:07:15 UTC+0800 2020
4/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01027796
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the vibration damper and the crankshaft pulley. Refer to Disassembly and
Assembly, "Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:08:11 UTC+0800 2020
2/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01027827
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
4C-6376 Seal Installer Stud 1
4C-6377 Seal Installer Washer 1
4C-6378 Seal Installer Sleeve 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00529163
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) with Tool (A) .
3. Remove Tool (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:09:07 UTC+0800 2020
2/2
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01646292
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00559575
Illustration 2 g00559536
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) .
3. Remove idler gear (3) .
2/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 3 g00559567
Illustration 4 g00559569
4. Use Tool (A) and remove idler shaft (4) from the cylinder block.
Illustration 5 g00559572
5. If necessary, remove five bolts (5) that hold front plate (6) to the cylinder block.
3/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 6. Remove front plate (6) and the gasket.
Note: See the following list for the removal of the other gears in the front gear group.
• In order to remove the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Remove and Install".
• In order to remove the fuel injection pump gear, refer to Disassembly and Assembly, "Fuel
Injection Pump Housing and Governor - Remove".
• In order to remove the gear to the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
• In order to remove the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 9 15:10:02 UTC+0800 2020
4/4
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315B L EXCAVATOR 3AW
Configuration: 315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POWERED BY 3046 ENGINE
Disassembly and Assembly
3046 Engine For Caterpillar Built Machines
Media Number -SENR6458-05 Publication Date -01/04/2004 Date Updated -22/04/2004
i01045442
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00559572
1. Install a new gasket and front plate (6) .
Note: Ensure that all mating surfaces are clean and free of old gasket material.
1/3
315B & 315B L TRACK-TYPE EXCAVATORS 3AW00001-UP (MACHINE) POW...
2020/11/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...