962K Wheel Loader Repair Manual

Service Repair Manual
Models
962K Wheel Loader

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962K WHEEL LOADER T6A
Configuration: 962K Wheel Loader T6A00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
950K and 962K Wheel Loaders Machine Systems
Media Number -KENR5805-00 Publication Date -01/10/2011 Date Updated -03/10/2011
i04551576
Piston Pump (Implement) - Assemble
SMCS - 5070-016-II; 5070-016; 5070-016-FD; 5084-016-QP; 5084-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 136-1452 Retaining Ring Pliers As 1
C - Loctite 271 -
D 6V-2055 Grease 1
Illustration 1 g02722272
1. Install cover (58) and bolts (57) .
1/14
962K Wheel Loader T6A00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP...
2020/4/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

3. Install bearings (54) .
2/14
2020/4/4

4. Install bearings (53) onto swashplate (52) .
5. Install swashplate (52) .
6. Raise the temperature of bearing (51) .
7. Install retaining ring (50) and bearing (51) onto shaft assembly (49) .
3/14
2020/4/4

8. Install shaft assembly (49) .
9. Use Tooling (B) in order to install retaining ring (48) .
10. Install lip seals (47) .
4/14
2020/4/4

11. Install O-ring seals (46) .
12. Install cover (45) and retaining ring (44) .
13. Install springs (42) into barrel (43) .
5/14
2020/4/4

14. Install retainer (41) .
15. Install bearing (40) .
16. Install pistons (38) into retainer (39) .
6/14
2020/4/4

17. Install pistons (38) and retainer (39) into the barrel assembly.
18. Install barrel assembly (36), O-ring seal (35), and O-ring seal (37) .
19. Lower the temperature of bearing (34) .
7/14
2020/4/4

20. Install bearing (34) into the port block assembly .
21. Apply Tooling (D) to the back side of port plate (33) .
22. Install port plate (33) onto the port block assembly .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
23. Install port block assembly (32) and bolts (31) .
8/14
2020/4/4

injury.
24. Install guide (30), spring (29), backup ring (27), O-ring seal (28), and plug (26) into pump
control head (2) .
25. Install cover (25), bolts (22), adjustment screw (24), and locknut (23) .
9/14
2020/4/4

26. Install backup ring (18), O-ring seal (19), onto piston (17) .
27. Install spool (21), sleeve (20), and piston (17) into pump control head (2) .
28. Install the cover, bolts (14), adjustment screw (15), and locknut (16) .
10/14
962K Wheel Loader T6A00001-UP (MACHINE) POWERED BY C7.1 Engine(SE...
2020/4/4

29. Apply Tooling (C) to the threads of piston (12) .
30. Install piston (12) and ball (13). Tighten piston (12) to a torque of 350 ± 30 N·m (258 ± 22
lb ft).
Note: Do not use an impact wrench in order to install piston (12) .
Note: Allow Tooling (C) to dry for 4 hours at room temperature.
31. Install the O-ring seal, the backup ring, and piston (11) .
32. Install the cover, bolts (8), adjustment screw (10), and locknut (9) .
11/14
2020/4/4

33. Install spring (7) .
34. Install O-ring seal (6) and the backup ring.
12/14
2020/4/4

injury.
36. Install O-ring seals (3) .
37. Install head (2) and bolts (1) .
End By: Install the pump.
13/14
2020/4/4

Shutdown SIS
Previous Screen
i04889422
Electrohydraulic Control - Remove and Install
SMCS - 5702-010
Removal Procedure
Table 1
Required Tools
A - Loctite 222 -
1. Remove cushion (1).
1/6
2020/4/4

2. Remove plate (2).
3. Loosen knob (4) and remove arm rest (3).
4. Remove screws (5) and (6). Disconnect harness assemblies from switch assemblies (7).
2/6
2020/4/4

5. Remove screws (8) and cover (9).
6. Disconnect harness assemblies (12). Remove screws (11) and electrohydraulic controls (10).
7. Remove knob (13), screws (15), and boot (14).
Installation Procedure
3/6
2020/4/4

1. Install electrohydraulic controls (10) in the reverse order of removal.
a. Apply Tooling (A) to the threads of knob (13).
Removal Procedure (Joystick Control)
1. Remove four screws (1) and cover assembly (2).
2. Remove four screws (4) and cover (3).
4/6
2020/4/4

3. Disconnect cable straps (5).
4. Disconnect cable straps (6) and harness assemblies (7).
5/6
2020/4/4

5. Reposition boot (8) out of the way. Remove four nuts (11) and four bolts (10). Remove joy
stick (9).
Installation Procedure (Joystick Control)
1. Install joy stick (9) in the reverse order of removal.
a. Tighten nuts (11) to the following torque 6.5 ± 0.5 N·m (58 ± 4 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 4 11:54:00 UTC+0800 2020
6/6
2020/4/4

Shutdown SIS
Previous Screen
i04439336
Main Control Valve - Remove and Install
SMCS - 5051-010
Removal Procedure
Table 1
Required Tools
A
4C-6486 Stand 1
8S-7641 Tube 1
8S-7615 Pin 1
8S-8048 Saddle 1
B 138-7575 Link Bracket 2
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
Hydraulic oil pressure can remain in the hydraulic system on this
machine after the engine and pump have been stopped. Serious injury
1/6
2020/4/4

can result if this pressure is not released before any service is done on
the hydraulic systems. In order to prevent possible injury, release the
hydraulic system pressure before working on any fitting, hose, or
hydraulic component.
Lower all attachments to the ground before service is started. If the
hydraulic system must be serviced, tested, or adjusted with the
attachment in the raised position, the attachments and lift cylinders
must be supported properly.
Always move the machine to a location away from the travel of other
machines. Be sure that other personnel are not near the machine when
the engine is running and tests or adjustments are being made.
1. Use Tooling (A) in order to support lift arms (1) .
2. Release the system hydraulic pressure.
3. Drain the implement hydraulic system. Refer to Operation and Maintenance Manual,
"Hydraulic System Oil - Change" for the correct procedure.
2/6
2020/4/4

4. Remove cover assembly (2) .
5. Disconnect all hose assemblies (3) from the front of main control valve (6). Disconnect tube
assemblies (5) and harness assemblies (4) from main control valve. (6) .
Bottom view of main control valve
6. Disconnect harness assembly (7) and remove cable strap (8) .
3/6
2020/4/4

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

7. Remove bracket assemblies (9) from frame assembly (10). Reposition tube assemblies (5)
out of the way. Repeat for the opposite side.
8. Disconnect tube assemblies (11) and hose assemblies (12) .
4/6
2020/4/4

9. Separate bracket (13) from the frame assembly. Reposition tubes (14) in order to remove the
main control valve. Repeat for the opposite side.
10. Disconnect all hose assemblies (15) from the rear of the main control valve. Remove cable
straps (16) from the harness assembly.
Bottom view
5/6
2020/4/4

11. Remove bolts (17) from the main control valve .
12. Attach Tooling (B) to main control valve (6). The weight of main control valve (6) is
approximately 277 kg (610 lb). Position main control valve (6) on a suitable table
Installation Procedure
1. Install main control valve (6) in the reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 4 11:54:57 UTC+0800 2020
6/6
2020/4/4

962K Wheel Loader Repair Manual

Recommended

Recommended

More Related Content

What's hot

What's hot (13)

Similar to 962K Wheel Loader Repair Manual

Similar to 962K Wheel Loader Repair Manual (20)

More from fjsekdhjenmdn

More from fjsekdhjenmdn (20)

Recently uploaded

Recently uploaded (20)

962K Wheel Loader Repair Manual