This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Safety cautions are provided regarding the weight of the crankshaft and ensuring the engine is cool before working on it.
Kubota la1403 ec front loader service repair manualfjjskekdmmme
This document provides specifications and safety information for a Kubota front loader model LA1403EC. It includes:
1. Specifications for the loader model, bucket sizes, hydraulic system details, dimensions, and operational capacities.
2. Safety instructions for servicing the loader, including general precautions, safety starting and working procedures, avoiding fires, ventilation, acid burns, and emergency preparedness.
3. Terminology used to identify parts of the loader.
4. Tightening torques for screws, bolts, and hydraulic fittings on the loader.
5. Maintenance checklists and inspection procedures.
The document provides technical information and safety guidelines for servicing the Kub
Kubota la1403 front loader service repair manualfjjskekdmmme
This workshop manual provides information for servicing a Kubota LA1403 front loader. It is divided into three parts covering general information, the loader mechanism, and servicing procedures. The general section includes identification, safety, maintenance, and specifications. The mechanism section describes the construction and functions. The servicing section provides troubleshooting, repair, and assembly instructions.
Kubota kx121 2(h) excavator parts catalogue manualfjjskekdmmme
The document consists of the repeated text "classicmachinery.net" with no other substantive information. At the end, there is a brief note asking the reader to click a link for a complete manual, and to download a PDF first if there is no response to clicking the link.
John deere te gator utility vehicle service repair manualfjjskekdmmme
This technical manual provides information for servicing a Gator utility vehicle. It contains sections covering specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety. Safety is the first section and provides instructions on battery safety, protective equipment, emergency procedures, charging batteries and acid burns. Technicians should follow all safety procedures when servicing this high voltage electrical system.
John deere pro gator 2030 utility vehicle service repair manualfjjskekdmmme
This document provides specifications for a John Deere ProGator 2030 Utility Vehicle. It includes specifications for the diesel engine, electrical system, fuel system, drive train, hydraulic system, tires, dimensions, torque specifications for fasteners, diesel fuel requirements, lubricants, and coolants. The specifications are organized into labeled sections for easy reference to details on particular systems.
John deere jx75 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service the mowers.
John deere je75 21 inch walk-behind mower service repair manualfjjskekdmmme
The document is a technical manual for John Deere 21-Inch Walk-Behind Mower models. It provides an introduction and overview of the manual's contents and organization. The manual contains sections on general specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, and torque specifications to assist technicians in servicing the mower models. It emphasizes reading all instructions before attempting any repairs.
Kubota la1403 ec front loader service repair manualfjjskekdmmme
This document provides specifications and safety information for a Kubota front loader model LA1403EC. It includes:
1. Specifications for the loader model, bucket sizes, hydraulic system details, dimensions, and operational capacities.
2. Safety instructions for servicing the loader, including general precautions, safety starting and working procedures, avoiding fires, ventilation, acid burns, and emergency preparedness.
3. Terminology used to identify parts of the loader.
4. Tightening torques for screws, bolts, and hydraulic fittings on the loader.
5. Maintenance checklists and inspection procedures.
The document provides technical information and safety guidelines for servicing the Kub
Kubota la1403 front loader service repair manualfjjskekdmmme
This workshop manual provides information for servicing a Kubota LA1403 front loader. It is divided into three parts covering general information, the loader mechanism, and servicing procedures. The general section includes identification, safety, maintenance, and specifications. The mechanism section describes the construction and functions. The servicing section provides troubleshooting, repair, and assembly instructions.
Kubota kx121 2(h) excavator parts catalogue manualfjjskekdmmme
The document consists of the repeated text "classicmachinery.net" with no other substantive information. At the end, there is a brief note asking the reader to click a link for a complete manual, and to download a PDF first if there is no response to clicking the link.
John deere te gator utility vehicle service repair manualfjjskekdmmme
This technical manual provides information for servicing a Gator utility vehicle. It contains sections covering specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety. Safety is the first section and provides instructions on battery safety, protective equipment, emergency procedures, charging batteries and acid burns. Technicians should follow all safety procedures when servicing this high voltage electrical system.
John deere pro gator 2030 utility vehicle service repair manualfjjskekdmmme
This document provides specifications for a John Deere ProGator 2030 Utility Vehicle. It includes specifications for the diesel engine, electrical system, fuel system, drive train, hydraulic system, tires, dimensions, torque specifications for fasteners, diesel fuel requirements, lubricants, and coolants. The specifications are organized into labeled sections for easy reference to details on particular systems.
John deere jx75 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service the mowers.
John deere je75 21 inch walk-behind mower service repair manualfjjskekdmmme
The document is a technical manual for John Deere 21-Inch Walk-Behind Mower models. It provides an introduction and overview of the manual's contents and organization. The manual contains sections on general specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, and torque specifications to assist technicians in servicing the mower models. It emphasizes reading all instructions before attempting any repairs.
John deere ja65 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
John deere ja62 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service various systems of the mower.
John deere jx85 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
Hyundai 40 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structure, operation, inspection, troubleshooting, and repair of components within that system. Symbols are used to identify important safety information. Conversion tables are included to allow simple unit conversions.
Hyundai 35 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structures, operations, inspections, troubleshooting, and maintenance procedures for the components in that system. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 35 bh 9 forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The major steps include:
1) Disassembling the steering unit by removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, sleeve, spool, and pressure relief valve parts.
2) Assembling the spool and sleeve with neutral position springs installed in slots. Bearing races and seals are also installed.
3) Lubricating O-rings and seals before installing them using special tools to push them into place in the housing.
4) Proper positioning and alignment of parts is important during assembly to ensure correct functioning of the steering unit.
Hyundai 33 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a gear pump and controlled by a main relief valve and solenoid valve to engage the appropriate clutch for forward or reverse operation.
Hyundai 33 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The disassembly process involves removing components like the end cover, gearwheel set, cardan shaft, distributor plate, spool, sleeve and seals. The pressure relief valve is also disassembled by removing the plug, seal washers, setting screw, spring and piston. The assembly process describes fitting components like the spool, sleeve, cross pin, bearings, O-rings and lip seal back into the steering unit housing using various tools. Special care and markings are required when assembling the neutral position springs in the spool and sleeve.
Hyundai 30 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a charging pump in the torque converter and is filtered, cooled, and distributed to clutches by the transmission control valve to engage the appropriate clutch for the selected gear.
Hyundai 30 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The main steps for disassembly are: removing the end cover and gearwheel set; taking out the cardan shaft and distributor plate; pressing out the spool, sleeve, bearing races and thrust bearing; and disassembling the pressure relief valve. The main steps for assembly are: assembling the spool and sleeve with neutral position springs; fitting the bearing races and cross pin; installing the O-rings and lip seal using assembly tools; and reassembling other components. Precautions and the correct assembly pattern are emphasized to ensure proper reassembly.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d s excavator (prefix cyd) service repair manual (cyd0000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Assembling begins with pressing bearings into the main housing and determining the correct shim thickness. Seals, pins and other components are then installed to reassemble the final drive.
Caterpillar cat 323 d ln excavator (prefix sed) service repair manual (sed000...fjjskekdmmme
This document provides instructions for removing and installing piston cooling jets on a Caterpillar C6.4 engine. The procedure involves removing the oil pan, then removing each jet one by one using a 46 mm socket to rotate the engine. For installation, the jets are reinstalled and tightened to a specified torque, again using the socket to rotate the engine for access. Safety notices are provided to keep parts clean and prevent contamination.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjskekdmmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d ln excavator (prefix cyd) service repair manual (cyd000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Reassembling follows the reverse order, including pressing bearings into housings and using shims to set proper bearing preload.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjskekdmmme
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It lists the required tools and presents a step-by-step procedure that includes removing bolts and washers, lifting the housing off using a bracket and lifting device, removing the oil seal, cleaning surfaces, installing a new gasket and seal, and securing the housing back in place.
Caterpillar cat 323 d l excavator (prefix pbm) service repair manual (pbm0000...fjjskekdmmme
The document provides instructions for removing and installing a crankshaft on a 323D L Excavator. It describes:
1. Removing the front housing, rear seal, flywheel housing and oil pan before removing the crankshaft.
2. Using a socket and lifting straps to remove the crankshaft, which weighs 84-99 kg.
3. Checking crankshaft end play and installing in reverse order of removal, ensuring proper bearing installation and torque of bolts.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjskekdmmme
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and driver group to re-install these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar cat 323 d l excavator (prefix nzf) service repair manual (nzf0000...fjjskekdmmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using special tools to compress the valve springs, remove the valve keepers, and position the pistons at top dead center. Valve springs must be replaced in pairs and steps taken to ensure parts are clean and the valves are at the proper depth. The installation procedure reverses the removal process and includes inspecting parts and lubricating seals.
John deere ja65 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
John deere ja62 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service various systems of the mower.
John deere jx85 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
Hyundai 40 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structure, operation, inspection, troubleshooting, and repair of components within that system. Symbols are used to identify important safety information. Conversion tables are included to allow simple unit conversions.
Hyundai 35 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structures, operations, inspections, troubleshooting, and maintenance procedures for the components in that system. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 35 bh 9 forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The major steps include:
1) Disassembling the steering unit by removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, sleeve, spool, and pressure relief valve parts.
2) Assembling the spool and sleeve with neutral position springs installed in slots. Bearing races and seals are also installed.
3) Lubricating O-rings and seals before installing them using special tools to push them into place in the housing.
4) Proper positioning and alignment of parts is important during assembly to ensure correct functioning of the steering unit.
Hyundai 33 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a gear pump and controlled by a main relief valve and solenoid valve to engage the appropriate clutch for forward or reverse operation.
Hyundai 33 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The disassembly process involves removing components like the end cover, gearwheel set, cardan shaft, distributor plate, spool, sleeve and seals. The pressure relief valve is also disassembled by removing the plug, seal washers, setting screw, spring and piston. The assembly process describes fitting components like the spool, sleeve, cross pin, bearings, O-rings and lip seal back into the steering unit housing using various tools. Special care and markings are required when assembling the neutral position springs in the spool and sleeve.
Hyundai 30 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a charging pump in the torque converter and is filtered, cooled, and distributed to clutches by the transmission control valve to engage the appropriate clutch for the selected gear.
Hyundai 30 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The main steps for disassembly are: removing the end cover and gearwheel set; taking out the cardan shaft and distributor plate; pressing out the spool, sleeve, bearing races and thrust bearing; and disassembling the pressure relief valve. The main steps for assembly are: assembling the spool and sleeve with neutral position springs; fitting the bearing races and cross pin; installing the O-rings and lip seal using assembly tools; and reassembling other components. Precautions and the correct assembly pattern are emphasized to ensure proper reassembly.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d s excavator (prefix cyd) service repair manual (cyd0000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Assembling begins with pressing bearings into the main housing and determining the correct shim thickness. Seals, pins and other components are then installed to reassemble the final drive.
Caterpillar cat 323 d ln excavator (prefix sed) service repair manual (sed000...fjjskekdmmme
This document provides instructions for removing and installing piston cooling jets on a Caterpillar C6.4 engine. The procedure involves removing the oil pan, then removing each jet one by one using a 46 mm socket to rotate the engine. For installation, the jets are reinstalled and tightened to a specified torque, again using the socket to rotate the engine for access. Safety notices are provided to keep parts clean and prevent contamination.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjskekdmmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d ln excavator (prefix cyd) service repair manual (cyd000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Reassembling follows the reverse order, including pressing bearings into housings and using shims to set proper bearing preload.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjskekdmmme
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It lists the required tools and presents a step-by-step procedure that includes removing bolts and washers, lifting the housing off using a bracket and lifting device, removing the oil seal, cleaning surfaces, installing a new gasket and seal, and securing the housing back in place.
Caterpillar cat 323 d l excavator (prefix pbm) service repair manual (pbm0000...fjjskekdmmme
The document provides instructions for removing and installing a crankshaft on a 323D L Excavator. It describes:
1. Removing the front housing, rear seal, flywheel housing and oil pan before removing the crankshaft.
2. Using a socket and lifting straps to remove the crankshaft, which weighs 84-99 kg.
3. Checking crankshaft end play and installing in reverse order of removal, ensuring proper bearing installation and torque of bolts.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjskekdmmme
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and driver group to re-install these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar cat 323 d l excavator (prefix nzf) service repair manual (nzf0000...fjjskekdmmme
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using special tools to compress the valve springs, remove the valve keepers, and position the pistons at top dead center. Valve springs must be replaced in pairs and steps taken to ensure parts are clean and the valves are at the proper depth. The installation procedure reverses the removal process and includes inspecting parts and lubricating seals.
KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAIN MATKA
➒➌➎➏➑➐➋➑➐➐KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAIN MATKA
Tanjore Painting: Rich Heritage and Intricate Craftsmanship | Cottage9Cottage9 Enterprises
Explore the exquisite art of Tanjore Painting, known for its vibrant colors, gold foil work, and traditional themes. Discover its cultural significance today!
Heart Touching Romantic Love Shayari In English with ImagesShort Good Quotes
Explore our beautiful collection of Romantic Love Shayari in English to express your love. These heartfelt shayaris are perfect for sharing with your loved one. Get the best words to show your love and care.
The cherry: beauty, softness, its heart-shaped plastic has inspired artists since Antiquity. Cherries and strawberries were considered the fruits of paradise and thus represented the souls of men.
KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAIN MATKA
2. 15 - Engine
09 - Bedplate
00 - General
15 - 67 9813/7450-2 15 - 67
00 - General
Introduction .................................................... 15-67
Remove and Install ....................................... 15-68
Introduction
The bedplate acts as the main strength component
of the engine. it maintains the correct alignment and
supports the weight of the internal components.
Figure 145.
1
2
1 Bedplate
2 Crankcase
3. 15 - Engine
09 - Bedplate
00 - General
15 - 68 9813/7450-2 15 - 68
Remove and Install
Special Tools
Description Part No. Qty.
Template for Sealant
Bedplate to Crankcase
(4 Cyl)
892/12356 1
Torque Wrench
(10-100Nm)
993/70111 1
Consumables
Description Part No. Size
Cleaner/Degreaser
- General purpose
solvent based parts
cleaner
4104/1557 0.4L
CAUTION This component is heavy. It must only
be removed or handled using a suitable lifting
method and device.
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Remove the engine, refer to (PIL 15-00).
4. Remove the drive belt, refer to (PIL 15-18).
5. Remove the crankshaft pulley, refer to (PIL
15-12).
6. Remove the oil sump, refer to (PIL 15-45).
7. Disconnect and remove the fuel pipes from the
injectors, refer to (PIL 18-96).
8. Remove the rocker cover, refer to (PIL 15-42).
9. Remove the fuel injectors, refer to (PIL 18-18).
10. Remove the rocker assembly including the push
rods, refer to (PIL 15-42).
11. It is not necessary to remove the cylinder head
assembly to remove the crankshaft. If however
the cylinder head needs to be removed for other
reasons (for piston and connecting rod removal
for example) remove it now, refer to (PIL 15-06).
12. Remove the fuel injection pump, refer to (PIL
18-18).
13. Remove the starter motor, refer to (PIL 15-75).
14. Remove the high duty PTO (Power Take-Off)
device (if installed).
15. Position the engine upside down in a suitable jig
or fixture, supported at the front of the cylinder
block.
16. Remove the flywheel, refer to (PIL 15-54).
17. Remove the flywheel housing, refer to (PIL
15-54).
18. Remove the fuel injection pump drive gear, refer
to (PIL 15-51).
19. Remove the oil pump, refer to (PIL 15-60).
20. Remove the high duty PTO idler drive gear (if
installed), refer to (PIL 15-51).
21. Remove the crankshaft drive gear, refer to (PIL
15-51).
22. Remove the camshaft, refer to (PIL 15-15).
23. Remove the rear timing case, refer to (PIL
15-51).
24. If the pistons and connecting rods have not been
removed, undo and remove the main bearing
caps, refer to (PIL 15-12).
5. 15 - Engine
09 - Bedplate
00 - General
15 - 70 9813/7450-2 15 - 70
Remove
1. Remove the bedplate peripheral bolts.
2. Progressively remove the main bearing bolts in
reverse order starting at bolt 10. The bolts MUST
NOT be re-used. Discard the bolts.
3. Install the four temporary lifting bolts. Carefully
separate the bedplate from the crankcase. Use
suitable lifting equipment (if the bedplate is lifted
manually, two people will be required). DO NOT
use a lever to separate the bedplate.
4. Remove and discard the O-ring.
5. Carefully remove the upper bearing shells from
the bedplate, remove the bedplate.
Figure 147.
18
18
18
18
18
T6
T6
T6
18
12
T6
P3
13
11
A (T5)
V
YY P2
51
9
4
8
3
7
62
10
T4
T4
W
P2
B (T5)
Y Y P2
X
1-10 Main bearing bolts 11 Bedplate peripheral bolts (x16)
12 Bedplate 13 Crankcase
18 Lower bearing shells (x5) A Left side template
B Right side template T3 Angle Gauge (obtain locally)
6. 15 - Engine
09 - Bedplate
00 - General
15 - 71 9813/7450-2 15 - 71
T4 Guide pins (x2 obtain locally) T5 Sealant template
T6 Lifting bolts (x4 obtain locally) V Sealant template portion for removal
W Bearing tab X Rear main bearing
Y Bearing location tab P2 Anaerobic sealant
P3 O-ring
7. 15 - Engine
09 - Bedplate
00 - General
15 - 72 9813/7450-2 15 - 72
Before Installation
1. Clean off all traces of the old sealant compound
from the crankcase and bedplate mating faces.
2. Use a suitable degreasing agent to carefully
clean the main bearing saddles in the bedplate
and crankcase. Take care not to block the oil
ways or the piston cooling jets.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
Important: Anaerobic sealant will not start to cure
whilst it is open to the atmosphere, however when
air is excluded (for instance when the two parts are
put together) it will immediately start to harden. Make
sure that all the necessary tools, bolts etc. are readily
available prior to assembling the components. The
parts must be installed and tightened to the correct
torque value within 5 minutes (with a maximum
permissible time of 15 minutes).
Important: BEFORE installing the bedplate: DO NOT
rotate the crankshaft. Make sure that the upper main
bearing shells are flush with the bottom face of the
crankcase.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. Install the two guide pins T4 to the crankcase
bedplate fixing holes as shown.
4. Install the four lifting bolts T6 to the bedplate as
shown.
5. Install a new O-ring at the bedplate.
6. Use a suitable degreasing agent to clean both
sides of the lower bearing shells. Assemble the
lower bearing shells into the bedplate. Lubricate
the lower bearing shells with clean engine oil.
Note: Make sure that the location tab W engages
in the slot as shown.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
7. Note: The sealant template T5 is used on
the crankcase, NOT the bedplate. The sealant
template T5 comprises of two pieces, A and B.
Modify the template A by removing portion V.
Special Tool: Template for Sealant Bedplate to
Crankcase (4 Cyl) (Qty.: 1)
8. Locate the holes in the templates A and B using
four fixing bolts at positions Y. Use the templates
as a guide apply beads of sealant P2 around the
crankcase/bedplate mating face as shown to the
dimension specified.
Length/Dimension/Distance: 1.5mm
9. Remove the four fixing bolts at positions Y.
Remove the templates A and B, make sure
you do not smudge the sealant. Discard the
templates.
10. Add beads of sealant P2 around the four bolt
holes at positions Y, so as to join the sealant
beads as shown at X.
11. Make sure that the location guide pins T4 are in
position in the crankcase. Assemble the bedplate
to the crankcase use the alignment guide pins.
12. Note: The bedplate is heavy. Two people will
be required to lift and rotate the bedplate safely
on to the crankcase. Install new main bearing
bolts 1-10. Tighten the bolts to the correct torque
value in pairs, starting in the centre and working
outwards (in sequence 1-10) to the 1st stage pre-
torque.
Special Tool: Torque Wrench (10-100Nm) (Qty.:
1)
13. Install the bedplate peripheral bolts. Tighten the
bolts to the correct torque value.
14. After installation and tightening the bedplate
peripheral bolts, further tighten the main bearing
bolts in pairs, starting in the centre and working
outwards (in sequence 1-10) to the 2nd stage
pre-torque.
15. Finally, angle tighten the main bearing bolts in
pairs, starting in the centre and working outwards
(in sequence 1-10) for the final stage torque. Use
the torque and angle method, refer to Fasteners
and Fixings, General, Introduction (PIL 72-00).
Important: If the parts have not been tightened to the
correct torque value within the maximum 15 minute
time period, then the parts must be separated,
thoroughly cleaned and fresh sealant applied.
After Installation
1. Check that the crankshaft can be freely rotated
by hand. Remove the bedplate lifting bolts T6.
2. Carry out the procedures listed, Before removal
in reverse order.
Table 54. Torque Table
Item Torque Value
1-10 (1st Stage) 50N·m
1-10 (2nd Stage) 115N·m
8. 15 - Engine
12 - Crankshaft
00 - General
15 - 76 9813/7450-2 15 - 76
Technical Data
Table 55.
Main bearing journal diameter (x4)
- min 87.98mm
- max 88mm
Main rear bearing journal diameter (x1)
- min 99.98mm
- max 100mm
Connecting rod bearing journal diameter
- min 72.98mm
- max 73mm
Maximum wear and ovality on journals
(1)
Crankshaft induction hardness 55 HRc min on surface
Thrust washer width
- min 2.44mm
- max 2.5mm
Crankshaft end float
- min 0.05mm
- max 0.28mm
(1) No visible damage/wear or marks
9. 15 - Engine
12 - Crankshaft
00 - General
15 - 77 9813/7450-2 15 - 77
Component Identification
Figure 148.
B
A
A Crankcase
B Crankshaft
10. 15 - Engine
12 - Crankshaft
00 - General
15 - 78 9813/7450-2 15 - 78
Operation
Lubrication
Oil is fed from the main gallery via five drillings, one
to each of the main bearings. A groove around the
diameter of the upper main bearing shell allows oil
transfer to cross drillings in the crankshaft to feed
each of the big end bearings. Crankshaft gear is
'splash' lubricated. Front and rear crankshaft oil seals
prevent oil leakage from, and dirt ingress to, the
engine.
Figure 149.
1 Main gallery 2 Drillings (x5)
3 Main bearings 4 Big end bearings
5 Cross drillings 6 Crankshaft gear
7 Crankshaft oil seal 8 Crankshaft oil seal
11. 15 - Engine
12 - Crankshaft
00 - General
15 - 79 9813/7450-2 15 - 79
Check (Condition)
1. Check the main bearing surfaces for damage and
excessive wear.
Figure 150.
A
A Main bearing shells
2. Measure the crankshaft diameters to confirm
they are within service limits, refer to Technical
Data (PIL 15-12).
Figure 151.
B
B Crankshaft
3. Check that the oil-way cross drillings in the
crankshaft are clear and free from debris.
Blocked or restricted oil-ways will cause oil
starvation at the big end bearings.
4. Check that the piston cooling J-jets are clear. If
the J-jets cannot be cleared remove the fixing
screws. Remove theJ-jets and discard them.
5. Install new J-jets.
Figure 152.
D
C
C J-jets
D Fixing screws
12. 15 - Engine
12 - Crankshaft
00 - General
15 - 80 9813/7450-2 15 - 80
Remove and Install
Consumables
Description Part No. Size
Cleaner/Degreaser
- General purpose
solvent based parts
cleaner
4104/1557 0.4L
CAUTION This component is heavy. It must only
be removed or handled using a suitable lifting
method and device.
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Remove the engine, refer to (PIL 15-00).
4. Remove the drive belt, refer to (PIL 15-18).
5. Remove the crankshaft pulley, refer to (PIL
15-12).
6. Remove the oil sump, refer to (PIL 15-45).
7. Disconnect and remove the fuel pipes from the
injectors, refer to (PIL 18-96).
8. Remove the rocker cover, refer to (PIL 15-42).
9. Remove the fuel injectors, refer to (PIL 18-18).
10. Remove the rocker assembly including the push
rods, refer to (PIL 15-42).
11. It is not necessary to remove the cylinder head
assembly to remove the crankshaft. If however
the cylinder head needs to be removed for other
reasons (for piston and connecting rod removal
for example) remove it now, refer to (PIL 15-06).
12. Remove the fuel injection pump, refer to (PIL
18-18).
13. Remove the starter motor, refer to (PIL 15-75).
14. Remove the high duty PTO device (if installed).
15. Position the engine upside down in a suitable jig
or fixture, supported at the front of the cylinder
block.
16. Remove the flywheel, refer to (PIL 15-54).
17. Remove the flywheel housing, refer to (PIL
15-54).
18. Remove the fuel injection pump drive gear, refer
to (PIL 15-51).
19. Remove the oil pump, refer to (PIL 15-60).
20. Remove the high duty PTO idler drive gear (if
installed), refer to (PIL 15-51).
21. Remove the crankshaft drive gear, refer to (PIL
15-51).
22. Remove the camshaft, refer to (PIL 15-15).
23. Remove the rear timing case, refer to (PIL
15-51).
24. If the pistons and connecting rods have not been
removed, undo and remove the main bearing
caps, refer to (PIL 15-12).
25. Remove the bedplate, refer to (PIL 15-09).
Remove
1. Remove the thrust washers between the
crankshaft and crankcase rear main bearing.
13. 15 - Engine
12 - Crankshaft
00 - General
15 - 81 9813/7450-2 15 - 81
Figure 153.
C
B
A
A
A Thrust Washers B Crankshaft
C Rear main bearing
2. Put labels on the thrust washers to make sure
that they are installed in the correct positions
during assembly.
3. Use suitable lifting equipment to carefully lift the
crankshaft from the crankcase (if the crankshaft
is lifted manually, two people will be required).
4. Carefully lift out the bearing shells.
Figure 154.
D
D Main bearing shells
5. It is recommended that the bearing shells are
replaced. If however they are to be used again,
put label on the shells to make sure that they
are installed in their original positions during
assembly.
6. Inspect the crankshaft and main bearings etc.
for damage and excessive wear. Refer to Check
Condition (PIL 15-12).
Before Installation
1. Clean off all traces of the old sealant compound
from the crankcase and bedplate mating faces.
2. Use a suitable degreasing agent to carefully
clean the main bearing saddles in the bedplate
and crankcase. Take care not to block the oil
ways or the piston cooling jets.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
Important: Cleanliness is of the utmost importance.
Blocked oil-ways or oil jets will cause engine failure.
Before you install the crankshaft make sure that ALL
oil-ways and jets are clear and free from debris.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. If removed or a new crankcase is being installed
then install cooling J jets as follows:
14. 15 - Engine
12 - Crankshaft
00 - General
15 - 82 9813/7450-2 15 - 82
Figure 155.
F
E
E J jets (x4)
F Fixing screws
3.1. Insert the cooling jets into the crankcase.
3.2. Note: There are different types of cooling
jets installed depending on the engine
application. The jets are colour coded.
3.3. Be sure to install the correct jets. Refer to
the relevant parts catalogue for the correct
cooling jet identification.
3.4. Tighten the retaining screws to the correct
torque value.
4. Install the upper bearing shells as follows:
Figure 156.
D
G
D Main bearing shells
G Bearing location tab
4.1. Use a suitable degreasing agent to make
sure that the surface of the upper bearing
shells are clean.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
4.2. Assemble the bearing shells into the
crankcase bearing saddles. Make sure that
the location tab engages into the slot as
shown.
4.3. Important: Make sure that the oil-way holes
in the bearing saddles align with the holes
in the bearing shell. If the holes are even
partially misaligned the piston cooling oil jet
will be restricted, causing the engine to fail.
4.4. Lubricate the upper bearing shells with
clean engine oil.
5. Use suitable lifting equipment (if the crankshaft
is lifted manually, two people will be required), to
carefully lower the crankshaft into the crankcase.
DO NOT rotate the crankshaft, the bearing shells
can become dislodged, refer to step 4.
6. Install the thrust washers as follows:
15. 15 - Engine
12 - Crankshaft
00 - General
15 - 83 9813/7450-2 15 - 83
Figure 157.
C
B
A
A
A
H
A Thrust washers B Crankshaft
C Rear main bearing H Oil slot - thrust washers
6.1. Slide the thrust washers between the
crankshaft and the crankcase rear main
bearing.
6.2. Make sure that they are installed in the
correct positions, with the two slots facing
outwards from the bearing saddle.
6.3. If necessary, push the crankshaft forward
and then backwards to obtain clearance to
install the thrust washers.
6.4. DO NOT rotate the crankshaft, the bearing
shells can become dislodged, refer to step
4.
7. Check that the crankshaft end float is within
service limits, refer to Technical Data (PIL 15-12).
Table 56. Torque Values
Item Nm
F 24
16. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 84 9813/7450-2 15 - 84
03 - Main Bearing
Introduction .................................................... 15-84
Check (Condition) .......................................... 15-85
Remove and Install ....................................... 15-85
Introduction
In a piston engine, the main bearings are the
bearings on which the crankshaft rotates.
The bearings hold the crankshaft in place and
prevent the forces created by the piston and
transmitted to the crankshaft by the connecting rods
from dislodging the crankshaft, instead forcing the
crank to convert the reciprocating movement into
rotation.
Figure 158.
A
B
A Main bearing
B Crankshaft
17. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 85 9813/7450-2 15 - 85
Check (Condition)
(For: JCB Tier 4i /T4F <55kW Engine 4
Cyl)
1. Check the bearing shell surfaces for signs of
damage and excessive wear.
2. Measure the crank pin diameters to confirm they
are within service limits.
Refer to: PIL 15-12-00.
3. Renew any parts that are worn or not within the
specified tolerances.
Remove and Install
(For: JCB Tier 4i /T4F <55kW Engine 4
Cyl)
Special Tools
Description Part No. Qty.
Torque Wrench
(10-100Nm)
993/70111 1
Before Removal
This procedure requires service parts. Make sure
you have obtained the correct service parts before
you start. Refer to Parts Catalogue.
1. Make the machine safe.
Refer to: PIL 01-03.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Remove the engine from the machine.
Refer to: PIL 15-00-00.
4. Disconnect and remove the fuel pipes from the
injectors.
Refer to: PIL 18-96-00.
5. Remove the rocker cover.
Refer to: PIL 15-42-06.
6. Remove the fuel injectors.
Refer to: PIL 18-18-03.
7. Drain the oil from the engine.
Refer to: PIL 15-21-00.
8. Remove the oil sump.
Refer to: PIL 15-45-00.
9. Position the engine upside down in a suitable jig
or fixture, supported at the front of the crankcase.
The connecting rod and the big-end bearing cap
have been fracture split and must be kept together
as a set. Care must be taken to avoid contamination
and or damage to the fracture split surfaces.
Remove
1. It is recommended that the big-end bearing caps
are removed in pairs, cylinders 1 and 4 and
cylinders 2 and 3. Rotate the crankshaft so that
the big-end bearing caps on cylinders 2 and 3 are
positioned as shown.
18. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 86 9813/7450-2 15 - 86
2. Remove the bolts and lift off the big-end bearing
caps from the connecting rods. The bolts must
not be re-used, discard the bolts.
Figure 159.
X
1 2
1 Big-end bearing caps
2 Big-end bearing cap bolts
X Cast notch
2.1. Make sure that the tool is kept in inline
with the bolt to avoid damaging the screw
thread.
3. Lift out the bearing shells from the bearing caps.
Carefully rotate the crank to disengage from the
connecting rods and get access to the upper
bearing shells. Lift out the upper bearing shells.
It is recommended that the bearing shells are
renewed. If they are to be reused, label the
bearing shells to make sure that they are installed
in their original positions on assembly.
Figure 160.
4
3
Z
1
2
6
5
1 Big-end bearing cap
2 Bolts
3 Connecting rod
4 Piston
5 Piston rings
6 Big end bearing shells
Z Fracture split surfaces
4. Carefully rotate the crankshaft to position the big-
end bearing caps of cylinders 1 and 4. Make
sure that the crank does not foul the connecting
rods of cylinders 2 and 3. Remove the bearing
caps and bearing shells as described in previous
steps.
5. Inspect the big-end bearings for signs of damage
and excessive wear.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. Install the upper bearing shell to the connecting
rod. Lubricate the bearing shell with clean engine
oil.
4. Install the lower bearing shell to the big-end
bearing cap. Lubricate the bearing shell with
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 87 9813/7450-2 15 - 87
clean engine oil. Install the big-end bearing cap
to the connecting rod. Make sure that the cast
notch on the bearing cap faces to the front of the
engine. Use compressed air to clean the fracture
surfaces before assembly.
5. Install new big end bearing cap bolts. Tighten the
new bolts in three stages to the correct torque
value.
Special Tool: Torque Wrench (10-100Nm) (Qty.:
1)
5.1. Make sure that the tool is kept in inline
with the bolt to avoid damaging the screw
thread.
5.2. The bolts are tightened using a torque and
angle method.
Refer to: PIL 72-00-00.
Figure 161.
0° +90°
Y
Figure 162.
T3
T3 Angle gauge (obtain locally)
After Installation
1. The after installation procedure is the opposite of
the before removal procedure.
Table 57. Torque Table
Item Torque Value
(Nm)
Angle (de-
grees)
2 (1st Stage) 35
2 (2nd Stage) 65
2 (Final Stage) 90
21. 15 - Engine
12 - Crankshaft
06 - Front Oil Seal
15 - 88 9813/7450-2 15 - 88
06 - Front Oil Seal
Remove and Install
(For: JCB Tier 4i /T4F <55kW Engine 4
Cyl)
Special Tools
Description Part No. Qty.
Crankshaft Front Oil
Seal Installation Tool
892/01157 1
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Remove the drive belt, refer to (PIL 15-18).
5. Remove the crankshaft pulley, refer to (PIL
15-12-12).
Remove
1. Use a suitable lever behind the lip of the
seal, carefully prise out the oil seal from the
counterbore in the crankcase. Take care not
to scratch or damage the counterbore or the
crankshaft hub. Damaged or dirty sealing faces
will cause the oil seal to fail.
Figure 163.
C
A
B
A Crankshaft oil seal
B Crankcase
C Crankshaft hub
Install
1. Make sure that the counterbore and the
crankshaft hub are clean and free from damage
and corrosion. Use a suitable degreasing agent
to clean all traces of oil and grease from the
counterbore. Important: The oil seal has a special
coating and MUST be installed dry without
lubricant.
2. Dismantle the seal installation tool. Bolt the
centre body to the crankshaft hub, using the
bolts. Refer to Figure 164.
Special Tool: Crankshaft Front Oil Seal
Installation Tool (Qty.: 1)
3. Install the oil seal on to the centre body. Make
sure that the seal is installed the correct way
around. Assemble the outer sleeve on to the
centre body and install the screw. Refer to Figure
164.
22. 15 - Engine
12 - Crankshaft
06 - Front Oil Seal
15 - 89 9813/7450-2 15 - 89
Figure 164.
F D
G
H
B
G
F
C
A
E
A Crankshaft oil seal B Crankcase
C Crankshaft hub D Seal installation tool
E Fixing bolts (x3) F Centre body
G Outer sleeve H Screw
4. Turn the screw to push the seal squarely into
the counterbore until the outer sleeve comes
up against the front edge of the counterbore.
When correctly installed, the front face of the seal
should be flush with the edge of the counterbore
within the specified tolerance. Refer to Figure
165.
Dimension: -0.5 -0/+0.5mm
Figure 165.
B
G
F
C
A
A Crankshaft oil seal
B Crankcase
C Crankshaft hub
F Centre body
G Outer sleeve
5. Remove the seal installation tool.