Caterpillar cat m313 d wheeled excavator (prefix k3d) service repair manual (k3d00001 and up)

Service Repair Manual
Models
M313D WHEELED Excavator

Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M313D WHEELED EXCAVATOR K3D
Configuration: M313D Excavator K3D00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
M313D Wheeled Excavator Power Train
Media Number -KENR6026-02 Publication Date -01/10/2013 Date Updated -17/10/2013
i02512536
Final Drive Carriers, Hubs and Brakes - Disassemble - Front
Axle
SMCS - 4054-015; 4092-015; 4253-015; 4255-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1863 Retaining Ring Pliers 1
B
5F-7465 Puller Assembly 1
1S-5188 Puller leg 2
5P-4750 Adjustment Screw 1
1P-0510 Screw 1
C 267-6564 Spanner 1
D 1U-5832 Pry Bar 1
E 1U-6410 Three Jaw Puller 1
F 1P-0510 Driver Gp 1
G 5P-4197 Spacer 1
H 1A-1935 Full Nut 1
3H-0465 Push-Puller Plate 4
5F-7342 Adapter 2
5F-7343 Bearing Puller Gp 1
1/10(W)w
2020/4/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

5F-7366 Forcing Screw 1
5P-8248 Hard Washer 2
6B-6684 Full Nut 2
6V-8237 Washer 1
8B-7549 Puller Leg 2
9S-7338 Crossblock 1
Start By:
A. Remove the front tires and rims. Refer to Disassembly and Assembly, "Tire and Rim -
Remove".
B. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the front final drives into a suitable container.
Illustration 1 g00894123
2/10(W)w

2. Attach a suitable lifting device to carrier housing (2) .
3. Remove bolts (1) .
4. Remove carrier housing (2). The weight of carrier housing (2) is approximately 31 kg (68
lb).
5. Disconnect hose assembly (3) .
6. Use Tooling (A) in order to remove retaining rings (4) .
3/10(W)w

7. Use Tooling (B) in order to remove planetary gears (5) from carrier housing (2) .
8. Remove thrust washer (6) .
9. Remove retaining ring (7), washer (8), and roller bearing (9) .
4/10(W)w

10. Use Tooling (A) in order to remove retaining ring (10). Remove thrust washers (11) and
(12) .
11. Remove bolt (13). Use Tooling (C) in order to remove nut (14) .
5/10(W)w

12. Remove O-ring seal (15). Remove ring gear housing (16) .
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove bolts (17), the springs, and the retainers. Remove piston (18) .
6/10(W)w

14. Remove O-ring seal (19), ring (20), O-ring seal (21), and ring (22) .
15. Remove clutch discs (23) .
16. Remove O-ring seal (24). Use Tooling (D) in order to remove carrier gear (25) .
7/10(W)w

17. Remove O-ring seal (26) .
18. Use a suitable lifting device, Tooling (E), Tooling (F), and Tooling (G) in order to remove
bearing cone (27) and flange (28) .
19. Attach a suitable lifting device to flange (28) and remove flange (28). The weight of flange
(28) is approximately 38 kg (83 lb).
8/10(W)w

20. Remove seal (29). Remove bearing cups (30) .
21. Remove spacer (31) .
22. Use Tooling (F), Tooling (G), and Tooling (H) in order to remove bearing cone (32) .
9/10(W)w

Shutdown SIS
Previous Screen
i02512623
Final Drive Carriers, Hubs and Brakes - Disassemble - Rear
Axle
SMCS - 4054-015; 4092-015; 4253-015; 4255-015
Disassembly Procedure
Table 1
Required Tools
B
5F-7465 Puller Assembly 1
1S-5188 Puller Leg 2
5P-4750 Adjusting Screw 1
1P-0510 Driver Group 1
D 1U-5832 Pry Bar 1
E 1U-6410 Three Jaw Puller 1
F 1P-0510 Driver Gp 1
G 1A-1935 Full Nut 1
3H-0465 Push-Puller Plate 4
5F-7342 Adapter 2
5F-7343 Bearing Puller Gp 1
5F-7366 Forcing Screw 1
1/10(W)w

5P-8248 Hard Washer 2
6B-6684 Full Nut 2
6V-8237 Washer 1
8B-7549 Puller Leg 2
9S-7338 Crossblock 1
Start By:
A. Remove the rear tires and rims. Refer to Disassembly and Assembly, "Tire and Rim -
Remove".
B. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
containing fluids.
1. Drain the oil from the front final drives into a suitable container.
2. Attach a suitable lifting device to carrier housing (2) .
2/10(W)w

3. Remove bolts (3) .
4. Remove carrier housing (2). The weight of carrier housing (2) is approximately 31 kg (68
lb).
5. Disconnect hose assembly (1) .
6. Use Tooling (A) in order to remove retaining rings (4) .
7. Use Tooling (B) in order to remove planetary gears (5) from carrier housing (2) .
8. Remove thrust washer (6) .
3/10(W)w

9. Remove retaining ring (7), washer (8), and roller bearing (9) .
4/10(W)w

10. Remove bolt (10). Use Tooling (C) in order to remove nut (11) .
11. Remove O-ring seal (12). Remove stub shaft (13) .
5/10(W)w

Note: Note the location of the alignment marks on ring gear housing (14) and the hub for
assembly purposes.
12. Use Tooling (D) to remove ring gear housing (14) .
13. Remove the bolts, the springs, and retainers (15). Remove piston (16) .
6/10(W)w

14. Remove O-ring seal (17), ring (18), O-ring seal (19), and ring (20) .
15. Remove brake discs (21) .
7/10(W)w

16. Remove O-ring seal (23). Use Tooling (D) in order to remove carrier gear (22) .
17. Remove O-ring seal (24) .
8/10(W)w

18. Use a suitable lifting device, Tooling (E), and Tooling (F) in order to remove bearing cone
(25) .
19. Use two people in order to remove flange (26). The weight of flange (26) is approximately
38 kg (83 lb).
20. Remove lip seal (27). Remove bearing cups (28) .
9/10(W)w

21. Remove spacer (29) .
22. Use Tooling (F) and Tooling (G) in order to remove bearing cone (30) .
23. Attach a suitable lifting device to hub (31). The weight of hub (31) is approximately 29 kg
(65 lb). Remove bolts (32) and hub (31) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 26 10:07:17 UTC+0800 2020
10/10(W)w

Shutdown SIS
Previous Screen
i03554744
Final Drive Carriers, Hubs and Brakes - Assemble - Front
Axle
SMCS - 4054-016; 4092-016; 4253-016; 4255-016
Assembly Procedure
Table 1
Required Tools
J 4C-5593 Anti-Seize Compound 1
K 6V-6080 Torque Multiplier Gp 1
L 269-7627 Seal Installer 1
NOTICE
containing fluids.
1/12(W)w

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Raise the temperature of bearing cone (32) and install bearing cone (32) .
2. Lower the temperature of bearing cups (30) and install bearing cups (30) .
2/12(W)w

3. Use Tooling (L) and a suitable press in order to install seal (29) .
4. Attach a suitable lifting device to flange (28) and install flange (28) . The weight of flange
(28) is approximately 38 kg (83 lb). Raise the temperature of bearing cone (27) and install
bearing cone (27) .
3/12(W)w

5. Install O-ring seal (19) , ring (20) , O-ring seal (21) , and ring (22) .
6. Position piston (18) . Install bolts (17) , the springs, and the retainers. Tighten bolts (17) to a
torque of 11 N·m (8 lb ft).
4/12(W)w

Caterpillar cat m313 d wheeled excavator (prefix k3d) service repair manual (k3d00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

Similar to Caterpillar cat m313 d wheeled excavator (prefix k3d) service repair manual (k3d00001 and up)

Similar to Caterpillar cat m313 d wheeled excavator (prefix k3d) service repair manual (k3d00001 and up) (10)

More from fjjskekdmem

More from fjjskekdmem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat m313 d wheeled excavator (prefix k3d) service repair manual (k3d00001 and up)