The document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. Key steps include:
1. Removing bolts fastening the front housing to the cylinder block and oil pan.
2. Removing the front housing and gasket.
3. Installing a new gasket and applying sealant.
4. Reinstalling the front housing and bolts, tightening to the specified torque.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...ujdfjjkskkmmde
The document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine:
1. To remove the front housing, first remove the engine oil pan, front gear group, and camshaft gear. Then remove all bolts fastening the front housing to the cylinder block and oil pan.
2. Installation involves applying gasket sealant, installing a new gasket on the front housing, and bolting the housing to the cylinder block and oil pan using a specific tightening sequence.
3. Reinstall the camshaft gear and front gear group to complete the process.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing a camshaft gear on a Caterpillar 3054 engine. It describes:
1) Rotating the crankshaft to align timing marks and removing the bolt and washer from the camshaft gear.
2) Using a puller tool to remove the camshaft gear and inspecting it for wear or damage.
3) Installing the camshaft gear, checking that the timing marks are aligned, and tightening the bolt.
This document provides instructions for removing and installing various engine components on a 248 Skid Steer Loader with a 3034 engine, including:
- Removing and installing the inlet manifold by removing bolts and checking the gasket
- Removing and installing inlet and exhaust valves by compressing springs, removing keepers and springs, and reinstalling in reverse order
- Removing and installing inlet and exhaust valve springs by compressing springs with a tool, removing retainers and springs, and reinstalling in reverse order
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It begins by listing the required tools and instructing the user to first remove the camshaft. It then describes using a camshaft bearing tool to press out the old bearings and press in the new ones. The user is advised to clean and lubricate all parts before installation. Finally, it notes to reinstall the camshaft and any other removed components once the bearings are replaced. The full document provides detailed step-by-step instructions and illustrations for completing this maintenance procedure.
Caterpillar cat 428 b backhoe loader (prefix 7ej) service repair manual (7ej0...fujjdfjkksekmem
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054 diesel engine. The removal procedure involves removing components like the rocker shaft and pushrods. The camshaft is then carefully removed from the engine. For installation, the camshaft is lubricated and carefully installed back into the engine. Thrust washers and dowels must be aligned properly. Removed components are then reinstalled in the reverse order. Instructions are also provided for removing and installing camshaft bearings and the engine oil pan.
Caterpillar cat 160 h es motor grader (prefix 6wm) service repair manual (6wm...fjsjjefkskekm
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 3306 engine. It describes the necessary tools and multi-step processes, which include removing caps and bearings, checking clearances dry, installing with oil, and torquing to specifications. Safety notices are included to keep parts clean and avoid damage.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fusjefjkskem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...ujdfjjkskkmmde
The document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine:
1. To remove the front housing, first remove the engine oil pan, front gear group, and camshaft gear. Then remove all bolts fastening the front housing to the cylinder block and oil pan.
2. Installation involves applying gasket sealant, installing a new gasket on the front housing, and bolting the housing to the cylinder block and oil pan using a specific tightening sequence.
3. Reinstall the camshaft gear and front gear group to complete the process.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing a camshaft gear on a Caterpillar 3054 engine. It describes:
1) Rotating the crankshaft to align timing marks and removing the bolt and washer from the camshaft gear.
2) Using a puller tool to remove the camshaft gear and inspecting it for wear or damage.
3) Installing the camshaft gear, checking that the timing marks are aligned, and tightening the bolt.
This document provides instructions for removing and installing various engine components on a 248 Skid Steer Loader with a 3034 engine, including:
- Removing and installing the inlet manifold by removing bolts and checking the gasket
- Removing and installing inlet and exhaust valves by compressing springs, removing keepers and springs, and reinstalling in reverse order
- Removing and installing inlet and exhaust valve springs by compressing springs with a tool, removing retainers and springs, and reinstalling in reverse order
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It begins by listing the required tools and instructing the user to first remove the camshaft. It then describes using a camshaft bearing tool to press out the old bearings and press in the new ones. The user is advised to clean and lubricate all parts before installation. Finally, it notes to reinstall the camshaft and any other removed components once the bearings are replaced. The full document provides detailed step-by-step instructions and illustrations for completing this maintenance procedure.
Caterpillar cat 428 b backhoe loader (prefix 7ej) service repair manual (7ej0...fujjdfjkksekmem
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054 diesel engine. The removal procedure involves removing components like the rocker shaft and pushrods. The camshaft is then carefully removed from the engine. For installation, the camshaft is lubricated and carefully installed back into the engine. Thrust washers and dowels must be aligned properly. Removed components are then reinstalled in the reverse order. Instructions are also provided for removing and installing camshaft bearings and the engine oil pan.
Caterpillar cat 160 h es motor grader (prefix 6wm) service repair manual (6wm...fjsjjefkskekm
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 3306 engine. It describes the necessary tools and multi-step processes, which include removing caps and bearings, checking clearances dry, installing with oil, and torquing to specifications. Safety notices are included to keep parts clean and avoid damage.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fusjefjkskem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
This document provides instructions for removing and disassembling the engine oil pump and water pump on a Caterpillar 3054 engine. It includes the following steps:
1. To remove the engine oil pump, remove the oil pan, front housing, strainer, suction pipe, and oil relief valve. Then remove three bolts to take off the pump.
2. To disassemble the water pump, drain the coolant, remove eight bolts and two nuts to take off the pump. Then remove six bolts on the cover, an O-ring seal, gear using a special tool, and seal using a lever.
3. The document provides detailed illustrations and torque specifications for reinstalling
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...ujdfjjkskkmmde
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and main bearing cap to access the oil pump.
2. Removing the retaining ring, idler gear, and three bolts to lift the pump off the bearing cap.
3. Cleaning and inspecting parts before installation. The instructions describe reinstalling these parts in reverse order and specify torque values for the fasteners.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...ujfdjjkjskkemm
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and No. 1 crankshaft main bearing cap to access the oil pump.
2. Using retaining ring pliers to remove the retaining ring and idler gear from the idler gear shaft.
3. Removing three bolts to detach the oil pump from the No. 1 main bearing cap.
4. Cleaning parts and applying Loctite to reinstall components in reverse order.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fjjsefkksemme
This document provides instructions for removing and disassembling the engine oil pump and water pump on a Caterpillar 3054 engine.
The engine oil pump removal instructions include removing the oil pan, front housing, strainer, suction pipe, and relief valve. The oil pump is then removed from the number 1 main bearing cap.
The water pump removal instructions include draining coolant, removing bolts and nuts securing the pump, and tapping the pump with a hammer to loosen and remove it from the front housing.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fjskefksemer
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and No. 1 crankshaft main bearing cap to access the oil pump.
2. Using retaining ring pliers to remove the retaining ring and idler gear from the idler gear shaft.
3. Removing three bolts to detach the oil pump from the No. 1 main bearing cap.
4. Cleaning and installing the oil pump by reversing the removal steps. Tightening bolts and rings to the specified torques.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fusjejfskekfmsme
The document provides instructions for installing and removing a crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes using specific tools to properly install the rear seal and housing. The procedure involves cleaning parts, lubricating the seal, aligning the housing, and tightening bolts to the specified torque. Instructions are provided for both engines with a 14 bolt housing and a 10 bolt housing.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fsejfjskefsmem
The document provides instructions for installing and removing a crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes using specific tools to properly install the rear seal and housing. The procedure involves cleaning parts, lubricating the seal, aligning the housing, and tightening bolts to the specified torque. Instructions are provided for both engines with a 14 bolt housing and a 10 bolt housing.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fjksekkmsemm
The document provides instructions for installing and removing a crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes using specific tools to properly install the rear seal and housing. The procedure involves cleaning parts, lubricating the seal, aligning the housing, and tightening bolts to the specified torque. Instructions are provided for both engines with a 14 bolt housing and a 10 bolt housing.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fujjsekskemme
This document provides instructions for installing and removing the crankshaft front seal on a 3054 engine. It describes using a drill bit and slide hammer puller to remove the old seal and a front seal installer tool to press the new seal into place. Proper cleaning and lubrication of parts is emphasized to prevent damage and wear.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fjjksekksemm
This document provides instructions for installing and removing the crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes cleaning and lubricating parts, using installation tools to correctly position components, and tightening bolts to the specified torques. Proper installation is important to prevent contamination and ensure long component life. Safety precautions are provided to contain fluids during maintenance.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fujsjefksekmfm
This document provides instructions for installing and removing the crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes cleaning and lubricating parts, using installation tools to correctly position the rear seal and housing, and tightening bolts to the specified torques. Instructions are also given for removing and installing the crankshaft pulley using thrust blocks and locking compound on the bolts.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...ujdjfjjkskkmme
This document provides instructions for installing and removing the crankshaft front seal on a Caterpillar 3054 engine. It outlines the necessary tools and steps to remove the existing seal using a drill bit and slide hammer puller. It then details how to prepare and install a new seal using a front seal installer tool, ensuring the seal is properly seated. The instructions are part of a service manual for maintenance and repair of a Caterpillar 436C backhoe loader.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...ufjjdkfkksmme
This document provides instructions for installing and removing the crankshaft front seal on a Caterpillar 3054 engine. It outlines the necessary tools and steps to remove the existing seal using a drill bit and slide hammer puller. It then explains how to clean and lubricate the housing and new seal before pressing the new seal into place using a front seal installer tool. The instructions are intended for use on a 436C backhoe loader with a 3054 engine.
Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr0...fjjskekksemmrt
1. The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 engine.
2. The removal procedure involves removing attaching bolts and removing the cover and gasket.
3. The installation procedure specifies applying a gasket sealant, installing a new gasket and cover, and tightening the attaching bolts to the specified torque.
New holland l221 tier 4 b final [nem479941 ]europe skid steer loader service...fjjsefkksemme
This document provides service information for New Holland skid steer and compact track loaders with Tier 4B diesel engines, including:
- Procedures for draining engine oil and coolant, removing the engine, radiator, and other components.
- Instructions for disconnecting hoses, wiring harnesses, and other connections when removing the engine.
- Notes on safety precautions and tilting the cab prior to engine removal.
New holland cx6090 elevation combine harvesters service repair manualfjjsefkksemme
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Komatsu pc180 lc 7k crawler excavator parts catalogue manual - sn k40001 and upfjjsefkksemme
This document provides part numbers and descriptions for components related to the cooling system of a Komatsu PC180LC-7K excavator with serial number K40001 and up. It includes 52 line items describing the radiator core assembly, radiator sheets, radiator frames, oil cooler, hoses, caps, plugs, bolts, washers, and other components that make up the radiator, oil cooler, and their mounting systems.
This document provides instructions for removing and installing the transmission on a 963 Track Loader. It describes in detail the 27 steps to remove the transmission, which includes draining fluids, disconnecting lines and hoses, removing mounting hardware, and lifting the transmission out. It then describes the 15 steps to install the transmission, which involves placing it back in position, reconnecting all lines and hoses, replacing mounting hardware, and refilling fluids. The overall process is to carefully disconnect and reconnect all transmission components and connections when removing and installing the transmission.
This document provides instructions for servicing components of a 963 Track Loader engine, including:
- Removing and installing the engine oil cooler, describing 11 steps
- Disassembling and assembling the oil filter base, describing 6 steps
- Removing the oil pan and oil pan plate, describing 7 steps for removal and 5 steps for installation
- Removing and installing the oil pump, describing 4 steps for removal and 5 steps for installation, and 10 additional steps for disassembling and assembling the oil pump.
Caterpillar cat 955 l track loader (prefix 13x) service repair manual (13x000...fjjsefkksemme
The document provides instructions for disassembling and assembling various components of a Caterpillar 3304 vehicular engine used in a 955L track loader, including:
- Removing and installing valve lifters, pistons, valves, valve seats, water directors, and valve guides.
- Disassembling and assembling pistons.
The procedures include detailed steps for each component, with pictures to illustrate certain steps. Safety notices are included throughout.
Caterpillar cat 955 k track loader (prefix 71j) service repair manual (71j045...fjjsefkksemme
This document provides instructions for servicing the power train of a Caterpillar 955K track loader, including:
- Checking and adjusting the flexible coupling alignment between the engine and transmission.
- Removing and installing the transmission and torque converter.
- Disassembling and assembling the planetary transmission and torque converter.
- Removing and installing the transmission hydraulic and mechanical controls.
Detailed step-by-step instructions are given for accessing, removing, and installing each component, along with specifications for alignment checks and torque values for fasteners. Potential causes of misalignment are discussed.
Caterpillar cat 953 c track loader (prefix bbx) service repair manual (bbx000...fjjsefkksemme
This document provides instructions for removing and installing track components on a Caterpillar 953C track loader. It describes:
1. Using hydraulic jacks, pins and lift forks to loosen the track and remove the track carrier roller.
2. Installing the track carrier roller by aligning dowels, bolting it in place and adjusting the tracks.
3. Removing track rollers by loosening tracks, removing bolts and lifting them out using a lifting fork.
4. Installing track rollers by positioning them on the frame, tightening bolts and adjusting tracks.
More Related Content
Similar to Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr01150 01155)
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
This document provides instructions for removing and disassembling the engine oil pump and water pump on a Caterpillar 3054 engine. It includes the following steps:
1. To remove the engine oil pump, remove the oil pan, front housing, strainer, suction pipe, and oil relief valve. Then remove three bolts to take off the pump.
2. To disassemble the water pump, drain the coolant, remove eight bolts and two nuts to take off the pump. Then remove six bolts on the cover, an O-ring seal, gear using a special tool, and seal using a lever.
3. The document provides detailed illustrations and torque specifications for reinstalling
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...ujdfjjkskkmmde
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and main bearing cap to access the oil pump.
2. Removing the retaining ring, idler gear, and three bolts to lift the pump off the bearing cap.
3. Cleaning and inspecting parts before installation. The instructions describe reinstalling these parts in reverse order and specify torque values for the fasteners.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...ujfdjjkjskkemm
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and No. 1 crankshaft main bearing cap to access the oil pump.
2. Using retaining ring pliers to remove the retaining ring and idler gear from the idler gear shaft.
3. Removing three bolts to detach the oil pump from the No. 1 main bearing cap.
4. Cleaning parts and applying Loctite to reinstall components in reverse order.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fjjsefkksemme
This document provides instructions for removing and disassembling the engine oil pump and water pump on a Caterpillar 3054 engine.
The engine oil pump removal instructions include removing the oil pan, front housing, strainer, suction pipe, and relief valve. The oil pump is then removed from the number 1 main bearing cap.
The water pump removal instructions include draining coolant, removing bolts and nuts securing the pump, and tapping the pump with a hammer to loosen and remove it from the front housing.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fjskefksemer
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and No. 1 crankshaft main bearing cap to access the oil pump.
2. Using retaining ring pliers to remove the retaining ring and idler gear from the idler gear shaft.
3. Removing three bolts to detach the oil pump from the No. 1 main bearing cap.
4. Cleaning and installing the oil pump by reversing the removal steps. Tightening bolts and rings to the specified torques.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fusjejfskekfmsme
The document provides instructions for installing and removing a crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes using specific tools to properly install the rear seal and housing. The procedure involves cleaning parts, lubricating the seal, aligning the housing, and tightening bolts to the specified torque. Instructions are provided for both engines with a 14 bolt housing and a 10 bolt housing.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fsejfjskefsmem
The document provides instructions for installing and removing a crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes using specific tools to properly install the rear seal and housing. The procedure involves cleaning parts, lubricating the seal, aligning the housing, and tightening bolts to the specified torque. Instructions are provided for both engines with a 14 bolt housing and a 10 bolt housing.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fjksekkmsemm
The document provides instructions for installing and removing a crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes using specific tools to properly install the rear seal and housing. The procedure involves cleaning parts, lubricating the seal, aligning the housing, and tightening bolts to the specified torque. Instructions are provided for both engines with a 14 bolt housing and a 10 bolt housing.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fujjsekskemme
This document provides instructions for installing and removing the crankshaft front seal on a 3054 engine. It describes using a drill bit and slide hammer puller to remove the old seal and a front seal installer tool to press the new seal into place. Proper cleaning and lubrication of parts is emphasized to prevent damage and wear.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fjjksekksemm
This document provides instructions for installing and removing the crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes cleaning and lubricating parts, using installation tools to correctly position components, and tightening bolts to the specified torques. Proper installation is important to prevent contamination and ensure long component life. Safety precautions are provided to contain fluids during maintenance.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fujsjefksekmfm
This document provides instructions for installing and removing the crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes cleaning and lubricating parts, using installation tools to correctly position the rear seal and housing, and tightening bolts to the specified torques. Instructions are also given for removing and installing the crankshaft pulley using thrust blocks and locking compound on the bolts.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...ujdjfjjkskkmme
This document provides instructions for installing and removing the crankshaft front seal on a Caterpillar 3054 engine. It outlines the necessary tools and steps to remove the existing seal using a drill bit and slide hammer puller. It then details how to prepare and install a new seal using a front seal installer tool, ensuring the seal is properly seated. The instructions are part of a service manual for maintenance and repair of a Caterpillar 436C backhoe loader.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...ufjjdkfkksmme
This document provides instructions for installing and removing the crankshaft front seal on a Caterpillar 3054 engine. It outlines the necessary tools and steps to remove the existing seal using a drill bit and slide hammer puller. It then explains how to clean and lubricate the housing and new seal before pressing the new seal into place using a front seal installer tool. The instructions are intended for use on a 436C backhoe loader with a 3054 engine.
Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr0...fjjskekksemmrt
1. The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 engine.
2. The removal procedure involves removing attaching bolts and removing the cover and gasket.
3. The installation procedure specifies applying a gasket sealant, installing a new gasket and cover, and tightening the attaching bolts to the specified torque.
Similar to Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr01150 01155) (14)
New holland l221 tier 4 b final [nem479941 ]europe skid steer loader service...fjjsefkksemme
This document provides service information for New Holland skid steer and compact track loaders with Tier 4B diesel engines, including:
- Procedures for draining engine oil and coolant, removing the engine, radiator, and other components.
- Instructions for disconnecting hoses, wiring harnesses, and other connections when removing the engine.
- Notes on safety precautions and tilting the cab prior to engine removal.
New holland cx6090 elevation combine harvesters service repair manualfjjsefkksemme
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Komatsu pc180 lc 7k crawler excavator parts catalogue manual - sn k40001 and upfjjsefkksemme
This document provides part numbers and descriptions for components related to the cooling system of a Komatsu PC180LC-7K excavator with serial number K40001 and up. It includes 52 line items describing the radiator core assembly, radiator sheets, radiator frames, oil cooler, hoses, caps, plugs, bolts, washers, and other components that make up the radiator, oil cooler, and their mounting systems.
This document provides instructions for removing and installing the transmission on a 963 Track Loader. It describes in detail the 27 steps to remove the transmission, which includes draining fluids, disconnecting lines and hoses, removing mounting hardware, and lifting the transmission out. It then describes the 15 steps to install the transmission, which involves placing it back in position, reconnecting all lines and hoses, replacing mounting hardware, and refilling fluids. The overall process is to carefully disconnect and reconnect all transmission components and connections when removing and installing the transmission.
This document provides instructions for servicing components of a 963 Track Loader engine, including:
- Removing and installing the engine oil cooler, describing 11 steps
- Disassembling and assembling the oil filter base, describing 6 steps
- Removing the oil pan and oil pan plate, describing 7 steps for removal and 5 steps for installation
- Removing and installing the oil pump, describing 4 steps for removal and 5 steps for installation, and 10 additional steps for disassembling and assembling the oil pump.
Caterpillar cat 955 l track loader (prefix 13x) service repair manual (13x000...fjjsefkksemme
The document provides instructions for disassembling and assembling various components of a Caterpillar 3304 vehicular engine used in a 955L track loader, including:
- Removing and installing valve lifters, pistons, valves, valve seats, water directors, and valve guides.
- Disassembling and assembling pistons.
The procedures include detailed steps for each component, with pictures to illustrate certain steps. Safety notices are included throughout.
Caterpillar cat 955 k track loader (prefix 71j) service repair manual (71j045...fjjsefkksemme
This document provides instructions for servicing the power train of a Caterpillar 955K track loader, including:
- Checking and adjusting the flexible coupling alignment between the engine and transmission.
- Removing and installing the transmission and torque converter.
- Disassembling and assembling the planetary transmission and torque converter.
- Removing and installing the transmission hydraulic and mechanical controls.
Detailed step-by-step instructions are given for accessing, removing, and installing each component, along with specifications for alignment checks and torque values for fasteners. Potential causes of misalignment are discussed.
Caterpillar cat 953 c track loader (prefix bbx) service repair manual (bbx000...fjjsefkksemme
This document provides instructions for removing and installing track components on a Caterpillar 953C track loader. It describes:
1. Using hydraulic jacks, pins and lift forks to loosen the track and remove the track carrier roller.
2. Installing the track carrier roller by aligning dowels, bolting it in place and adjusting the tracks.
3. Removing track rollers by loosening tracks, removing bolts and lifting them out using a lifting fork.
4. Installing track rollers by positioning them on the frame, tightening bolts and adjusting tracks.
Caterpillar cat 953 b track loader (prefix 5mk) service repair manual (5mk000...fjjsefkksemme
This document provides assembly instructions for a Type I governor used on a 953B track loader powered by a 3116 engine. It describes 19 steps to assemble the governor, including installing various springs, levers, and other components in the proper order and position. Safety notices are included to warn of potential injury from released spring forces. Tools required for the assembly are also listed.
New holland cx6080 elevation combine harvesters service repair manualfjjsefkksemme
This document is a service manual for CNH Industrial combine harvesters and covers the following models: CX5080 Elevation, CX5090 Elevation, CX5090 Laterale, CX5090 Hillside, CX6080 Elevation, and CX6090 Elevation. The manual contains information on the engine, transmission, axles, brakes, hydraulic and electrical systems, attachments, feeding, threshing, separation, cleaning, and unloading systems of the combines. It is organized by major component sections and includes part numbers and specifications.
Caterpillar cat 438 d backhoe loader (prefix bpe) service repair manual (bpe0...fjjsefkksemme
The document provides instructions for assembling the transmission of a 438D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, and seals in their proper order. Tools needed for the assembly are listed. Cleanliness is emphasized and components should be cleaned and oiled before installation. Tolerances for shaft play are provided to check proper assembly. The transmission is then installed in the vehicle and filled with the specified oil.
Caterpillar cat 438 c backhoe loader (prefix 9kn) service repair manual (9kn0...fjjsefkksemme
This document provides instructions for installing a turbocharger on a Caterpillar 3054 engine. It describes:
- Inspecting and installing gaskets before mounting the turbocharger
- Mounting the turbocharger using bolts and nuts
- Connecting oil and air lines with hoses and fittings
- Plugging all openings once installation is complete
The instructions are illustrated with diagrams and include notes about keeping components clean and containing fluids.
Caterpillar cat 438 c backhoe loader (prefix 9kn) service repair manual (9kn0...fjjsefkksemme
This document provides instructions for removing and installing the fuel injection pump and turbocharger on a Caterpillar 3054 engine.
The summary is:
1. The fuel injection pump removal procedure involves removing bolts, nuts, and covers to access the pump, then removing the pump and key.
2. Installing the fuel injection pump requires checking seals, aligning marks, installing bolts and nuts, and setting the pump timing.
3. Removing the turbocharger involves loosening hoses and lines, removing bolts and nuts, and removing the turbocharger and gaskets. Plugging openings is also specified.
New holland cx780 combine harvesters service repair manualfjjsefkksemme
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland b115 backhoe loader service repair manualfjjsefkksemme
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
Caterpillar cat 438 c backhoe loader (prefix 9kn) service repair manual (9kn0...fjjsefkksemme
The document provides instructions for disassembling and assembling Denso alternators for a Caterpillar 438C Backhoe Loader. It describes removing the alternator pulley nut, rear cover bolts, brush holder screws, voltage regulator screws, stator leads, and using a puller to separate the alternator case halves. Reassembly involves installing components in reverse order, pressing the case halves together and securing with bolts. Safety procedures are also outlined for fluid containment and preventing tire explosions.
New holland b100 ctc stage iv tractor loader backhoe service repair manualfjjsefkksemme
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 20 sections covering all major vehicle systems from the engine and transmission to hydraulics, steering, and electrical systems. Each section includes detailed component information, specifications, and repair or replacement procedures.
Caterpillar cat 438 c backhoe loader (prefix 2dr) service repair manual (2dr0...fjjsefkksemme
This document provides instructions for removing and installing an air conditioner compressor group, air conditioner filter, full air conditioner system, and cab from a Caterpillar 438C backhoe loader. It describes disconnecting wiring, removing mounting hardware, and reversing steps for installation. Safety warnings are provided regarding working with refrigerants and pressurized air conditioning systems.
New holland b100 c backhoe loader service repair manualfjjsefkksemme
This document is a service manual that contains instructions and specifications for maintenance and repair of backhoe loaders. It includes sections on safety rules, maintenance, technical specifications, dimensions and performance data. The technical specifications section provides details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets and tires of the backhoe loaders. The document also has sections that provide instructions for removing and installing major components like the engine, transmission, radiator and hood.
Caterpillar cat 438 c backhoe loader (prefix 2dr) service repair manual (2dr0...fjjsefkksemme
The document provides instructions for removing a fuel transfer pump on a Caterpillar 3054 engine. It begins by disconnecting the fuel lines at the fuel injection pump and capping the lines. Then it describes removing three bolts holding fuel lines to the rear of the engine and two bolts securing the fuel filter base. Finally, it discusses removing the fuel filter from the base by draining it first before full removal.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02108315
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
B. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
C. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Illustration 1 g00640000
1. Remove bolts (1) and nuts (3) from the front cover.
2. Remove front cover (2) and the gasket from the cylinder block.
Thu Oct 17 10:07:37 UTC+0800 2019
1/2438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01694904
Front Cover - Install
SMCS - 1166-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
B 4C-5501 Front Cover Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all surfaces of the front housing and clean the front cover thoroughly.
2. If necessary, use Tool (A) to install the crankshaft front oil seal. Refer to Disassembly and
Assembly, "Crankshaft Front Seal - Install".
1/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00640000
Illustration 2 g00546873
3. Install a new gasket and front cover (2) .
4. Install two bolts (1) in order to hold the gasket and the cover in place.
5. Use Tool (B) and the bolts for the crankshaft pulley in order to center the front cover.
NOTICE
The location of the front cover is critical. If the front cover is not
centered, the backlash between the fuel injection pump gear and the
water pump gear could be affected. This could result in damage to the
fuel injection pump.
6. Install the remaining bolts (1) and the two nuts (3). Tighten the nuts and the bolts to a torque
of 22 N·m (16 lb ft).
End By:
2/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
c. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:08:33 UTC+0800 2019
3/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02253357
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2264 Puller Group 1
B 173-9774 Wrench Bit 1
Start By:
A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00556563
Note: It may be necessary to pin the fuel pump in order to maintain the correct timing.
Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove"for the correct
procedure.
1. Align the timing marks on the crankshaft gear, the camshaft gear, and the idler gear, as
shown.
2. Remove bolts (1) from idler gear (2) .
3. Remove idler gear (2) and retainer plate (3) .
Illustration 2 g00556757
4. Remove bushing (4) from idler gear (2) , if necessary.
5. Remove the bushing with a suitable puller. If the bushing cannot be removed with a puller,
grind the face off of one bushing. The remainder of the bushing can then be removed with a
press.
2/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00556758
6. Remove idler gear hub (5) from the cylinder block.
7. Remove nut (6) and the spring washer from fuel injection pump gear (8) .
8. Remove bolts (7) from fuel injection pump gear (8) .
Note: Some fuel injection pump gears may have a tamper proof torx screw in place of one
of the four bolts. Use Tooling (B) to remove the tamper proof torx screw, if necessary.
9. Use Tooling (A) to remove fuel injection pump gear (8) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:09:28 UTC+0800 2019
3/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01744102
Gear Group (Front) - Install
SMCS - 1206-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00556758
1. Install fuel injection pump gear (8) on the engine.
2. Install bolts (7) on fuel injection pump gear (8).
1/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Install nut (6) and the spring washer on fuel injection pump gear (8). Tighten the nut to a
torque of 80 N·m (59 lb ft).
4. Install idler gear hub (5) on the engine.
Illustration 2 g00556757
5. Use a suitable press to install new bushings (4) into idler gear (2).
6. Machine the bores for clearance on idler gear hub (5). The bore should have a clearance of
0.04 to 0.010 mm (0.0016 to 0.0039 inch) on idler gear hub (5). The bore can have a
diameter of 57.14 to 57.18 mm (2.250 to 2.251 inch).
7. Machine the front faces of the bushings for the end play of idler gear (2). The gear and the
bushings can have a thickness of 30.14 to 30.16 mm (1.186 to 1.187 inch).
Illustration 3 g00556563
8. Install idler gear (2) and retainer plate (3) on the engine.
Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the idler
gear are aligned.
9. Install bolts (1) on idler gear (2). Tighten the bolts to a torque of 44 N·m (32 lb ft).
10. Check the end play of idler gear (2). Idler gear (2) should have end play of 0.10 to 0.20 mm
(0.004 to 0.008 inch).
2/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 11. Check the backlash between the camshaft gear and idler gear (2). The gears must have a
minimum backlash of 0.08 mm (0.003 inch).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:10:24 UTC+0800 2019
3/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01744128
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
b. Remove the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
c. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00549819
1. Remove all bolts (1) that fasten the front housing (2) to the cylinder block.
Illustration 2 g00549821
2. Remove bolts (3) that hold the oil pan to the bottom of front housing (2).
3. Remove front housing (2) and the gasket.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:11:20 UTC+0800 2019
2/2438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i06815567
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Gasket Sealant No. 2 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Replace the gasket.
2. Apply Tooling (A) to the bottom portion of the gasket.
1/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00549821
3. If necessary, install the studs (not shown) to the back of the front housing (2) that holds the
fuel injection pump in position. Tighten the studs to a torque of 11 N·m (97 lb in). Install
the gasket and front housing (2). Cut the gasket to the correct length, if necessary.
4. Install bolts (3) that hold the engine oil pan to the bottom of the front housing. Tighten the
bolts to a torque of 22 N·m (16 lb ft).
Illustration 2 g00549819
2/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 3 g03549798
5. Install all bolts (1) that fasten the front housing (2) to the cylinder block and to the oil pan.
Tighten bolts (1) to a torque of 22 N·m (16 lb ft) using the sequence in Illustration 3.
Note: Ensure that the bottom of the front housing is aligned with the bottom of the cylinder
block.
End By:
a. Install the camshaft gear.
b. Install the front gear group.
c. Install the engine oil pan.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:12:16 UTC+0800 2019
3/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01054405
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: The engines are equipped with either an aluminum valve cover or with a composite valve
cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet
1/5438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve
cover.
Illustration 1 g00547002
Typical example
Illustration 2 g00547003
Aluminum valve cover
2/5438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00547004
Composite valve cover
1. Loosen hose clamp (1) .
2. Disconnect breather hose (2) .
3. Remove three nuts (3), steel washers (6), and sealing washers (8) .
Note: When you remove nuts (3), ensure that the nuts on the rocker arm bracket are not
loosened.
Note: Current production engines have an additional shim washer (7) .
4. Remove valve cover (4), gasket (10), and seal (5) .
5. Remove seal (9) for the oil filler cap.
Installation Procedure
Note: The engines are equipped with either an aluminum valve cover or with a composite valve
cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet
manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve
cover.
3/5438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g00547002
Typical example
Illustration 5 g00547003
Aluminum valve cover
4/5438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 6 g00547004
Composite valve cover
1. Inspect the condition of the gaskets and the seals. Replace the gaskets and the seals, if
necessary.
2. Install seal (9) for the oil filler cap, if necessary.
3. Apply 8T-9022 Silicone Gasket to gasket (10) .
Note: Ensure that the flat face of the gasket is toward the valve cover.
4. Install gasket (10), seal (5), and valve cover (4) .
5. Lubricate three nuts (3) with clean engine oil.
6. Install three nuts (3), steel washers (6), and sealing washers (8) .
Note: When you install three nuts (3) without shim washers (7), tighten the nuts to a torque
of 20 N·m (15 lb ft). Do not overtighten the nuts.
Note: When you install three nuts (3) with shim washers (7), tighten the nuts to a torque of
30 N·m (22 lb ft). Do not overtighten the nuts.
7. Connect breather hose (2) .
8. Tighten hose clamp (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:13:11 UTC+0800 2019
5/5438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01761173
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00635152
1/2438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Typical example
Note: It is not necessary to remove the oil supply tube in order to remove the rocker shaft
assembly and the pushrods.
1. Remove nuts (1) and bolt (2) from the rocker shaft assembly. Begin with the end brackets
and move toward the center.
2. Remove rocker shaft assembly (3).
3. Remove the oil seal from the oil supply passage in the cylinder head.
Illustration 2 g00635153
Typical example
4. Remove pushrods (4). Place an identification mark on the pushrods for installation.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 17 10:14:07 UTC+0800 2019
2/2438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01667090
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
Illustration 1 g00550061
1/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 1. Use a screwdriver or a similar tool to remove retaining ring (1) from both ends of the rocker
shaft assembly.
Illustration 2 g00550062
(1) Retaining ring
(2) Washer on the end of the rocker shaft
(3) Rocker arm assembly
(4) Rocker shaft bracket
(5) Spring on the rocker shaft
(6) Washer
(7) Rocker shaft
(8) Bolt
(9) Oil supply connection
(10) Rocker arm bushing
2. Remove the rocker arms and the rocker shaft brackets from the rocker shaft assembly.
Note: Place an identification mark on each of the components for the proper order for
installation.
3. Check the clearance between rocker arm assembly (3) and rocker shaft (7). Replace rocker
arm bushing (10) if the clearance is larger than 0.13 mm (0.005 inch). Use Tool (A) and a
suitable press in order to remove rocker arm bushing (10) from rocker arm assembly (3), if
necessary.
4. Remove rocker shaft bracket (4) from rocker shaft (7) .
5. Remove springs (5), washer (6), bolt (8) and oil supply connection (9) from rocker shaft
(7) .
Thu Oct 17 10:15:03 UTC+0800 2019
2/3438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438C BACKHOE LOADER 1JR
Configuration: 438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01667093
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
1. Lubricate all of the components with clean engine oil.
Illustration 1 g00550062
(1) Retaining ring
(2) Washer on the end of the rocker shaft
(3) Rocker arm assembly
(4) Rocker shaft bracket
(5) Spring on the rocker shaft
(6) Washer
(7) Rocker shaft
1/2438C Backhoe Loader Center Pivot, Single Tilt 1JR01150-01155 (MACHINE) POWE...
2019/10/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...