This document provides disassembly and assembly instructions for a governor used in 3406C diesel engines for Caterpillar machines. It describes removing and installing over 50 individual parts in 37 steps. Key components that must be removed include the fuel injection pump housing, governor, fuel transfer pump, rear and front governor housings, springs, levers, shafts, seals, and the governor servo. Proper part identification and order are important for correct reassembly.
This service repair manual provides instructions for disassembling and assembling the governor component of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor housing and related components. The assembly process describes installing these same parts in the reverse order and making adjustments to ensure proper governor function.
This service repair manual provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor including housings, shafts, levers, springs, seals and bearings. The assembly process describes installing these same parts in the reverse order using various tools, with notes to ensure correct alignment and positioning of components.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts in 37 numbered steps. Key parts that are removed include the rear and front governor housings, shaft assembly, lever assemblies, springs, seals, and the governor servo. The assembly section similarly has over 30 parts that are installed in 23 numbered steps, putting the governor back together in reverse order of disassembly. Special tools are required for some steps like holding springs under compression.
This service repair manual provides instructions for disassembling and assembling the governor component of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor housing and related components. The assembly process describes installing these same parts in the reverse order and making adjustments to ensure proper governor function.
This service repair manual provides instructions for disassembling and assembling the governor component of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor housing and related components. The assembly process describes installing these same parts in the reverse order and making adjustments to ensure proper governor function.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts in 37 numbered steps. Key parts that are removed include the governor spring, lever assembly, shaft assembly, seals, covers, and servo. Reassembly follows the reverse order, with installation of races, bearings, springs, seals and other individual parts into the governor housing and fuel injection pump housing. Precise positioning and tool usage is required to properly assemble the governor.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts in 37 numbered steps. Key parts that are removed include the front and rear governor housings, shaft assembly, lever assemblies, springs, seals, and the governor servo. The assembly section similarly has over 30 parts that are installed in 23 numbered steps, putting the governor back together in reverse order of disassembly. Special tools are required for some steps like holding springs under compression.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This service repair manual provides instructions for disassembling and assembling the governor component of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor housing and related components. The assembly process describes installing these same parts in the reverse order and making adjustments to ensure proper governor function.
This service repair manual provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor including housings, shafts, levers, springs, seals and bearings. The assembly process describes installing these same parts in the reverse order using various tools, with notes to ensure correct alignment and positioning of components.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts in 37 numbered steps. Key parts that are removed include the rear and front governor housings, shaft assembly, lever assemblies, springs, seals, and the governor servo. The assembly section similarly has over 30 parts that are installed in 23 numbered steps, putting the governor back together in reverse order of disassembly. Special tools are required for some steps like holding springs under compression.
This service repair manual provides instructions for disassembling and assembling the governor component of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor housing and related components. The assembly process describes installing these same parts in the reverse order and making adjustments to ensure proper governor function.
This service repair manual provides instructions for disassembling and assembling the governor component of a 3406C diesel engine. The disassembly process involves removing 37 individual parts from the governor housing and related components. The assembly process describes installing these same parts in the reverse order and making adjustments to ensure proper governor function.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts in 37 numbered steps. Key parts that are removed include the governor spring, lever assembly, shaft assembly, seals, covers, and servo. Reassembly follows the reverse order, with installation of races, bearings, springs, seals and other individual parts into the governor housing and fuel injection pump housing. Precise positioning and tool usage is required to properly assemble the governor.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts in 37 numbered steps. Key parts that are removed include the front and rear governor housings, shaft assembly, lever assemblies, springs, seals, and the governor servo. The assembly section similarly has over 30 parts that are installed in 23 numbered steps, putting the governor back together in reverse order of disassembly. Special tools are required for some steps like holding springs under compression.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order. It concludes by instructing the installer to reinstall the fuel transfer pump and fuel injection pump housing.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order. It concludes by instructing the installer to reinstall the fuel transfer pump and fuel injection pump housing.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order. It concludes by instructing the installer to reinstall the fuel transfer pump and fuel injection pump housing.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling individual governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for the governor of a 3406C diesel engine used in Caterpillar machinery. It describes removing and installing over 30 individual governor components in 37 numbered steps. Key steps include removing the fuel injection pump housing, governor spring and lever assemblies, seals, shafts, bearings, flyweights and carrier assembly. Reassembly involves installing these same components in the reverse order. Precise positioning and tool usage is required to properly compress springs and install retaining rings.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts from the governor housing and fuel injection pump housing. The assembly process describes installing each part in reverse order and making adjustments to ensure proper governor function.
This document provides disassembly and assembly instructions for the governor of a 3406C diesel engine used in Caterpillar machinery. It describes removing and installing over 30 individual parts in 37 numbered steps. Key steps include removing the fuel injection pump housing, governor spring and lever assemblies, seals, shafts, bearings, flyweights and carrier assembly. Reassembly involves installing these same parts in the reverse order. Safety notes caution that the governor riser must be installed correctly to avoid holding the engine at maximum fuel delivery.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts from the governor housing and fuel injection pump housing. The assembly process describes installing each part in reverse order and making adjustments to ensure proper governor function.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in reverse order. Precise assembly is required to ensure proper governor function for fuel delivery control.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in reverse order. Precise positioning and tool usage is required to properly remove and replace small internal parts like seals and bearings.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise instructions are given to disassemble and reassemble small intricate parts like ensuring proper end play of flyweights on dowels during assembly.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in reverse order. Precise assembly is required to ensure proper governor function and prevent issues like holding the riser in maximum fuel delivery.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise assembly is required to ensure proper governor function that regulates fuel delivery based on engine speed.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
More Related Content
Similar to Caterpillar Cat 623E WHEEL SCRAPER (Prefix 5SG) Service Repair Manual Instant Download 7.pdf
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order. It concludes by instructing the installer to reinstall the fuel transfer pump and fuel injection pump housing.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order. It concludes by instructing the installer to reinstall the fuel transfer pump and fuel injection pump housing.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order. It concludes by instructing the installer to reinstall the fuel transfer pump and fuel injection pump housing.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling individual governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides disassembly and assembly instructions for the governor of a 3406C diesel engine used in Caterpillar machinery. It describes removing and installing over 30 individual governor components in 37 numbered steps. Key steps include removing the fuel injection pump housing, governor spring and lever assemblies, seals, shafts, bearings, flyweights and carrier assembly. Reassembly involves installing these same components in the reverse order. Precise positioning and tool usage is required to properly compress springs and install retaining rings.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts from the governor housing and fuel injection pump housing. The assembly process describes installing each part in reverse order and making adjustments to ensure proper governor function.
This document provides disassembly and assembly instructions for the governor of a 3406C diesel engine used in Caterpillar machinery. It describes removing and installing over 30 individual parts in 37 numbered steps. Key steps include removing the fuel injection pump housing, governor spring and lever assemblies, seals, shafts, bearings, flyweights and carrier assembly. Reassembly involves installing these same parts in the reverse order. Safety notes caution that the governor riser must be installed correctly to avoid holding the engine at maximum fuel delivery.
This document provides instructions for disassembling and assembling the governor of a 3406C diesel engine. The disassembly process involves removing over 30 individual parts from the governor housing and fuel injection pump housing. The assembly process describes installing each part in reverse order and making adjustments to ensure proper governor function.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in reverse order. Precise assembly is required to ensure proper governor function for fuel delivery control.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in reverse order. Precise positioning and tool usage is required to properly remove and replace small internal parts like seals and bearings.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise instructions are given to disassemble and reassemble small intricate parts like ensuring proper end play of flyweights on dowels during assembly.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in reverse order. Precise assembly is required to ensure proper governor function and prevent issues like holding the riser in maximum fuel delivery.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise assembly is required to ensure proper governor function that regulates fuel delivery based on engine speed.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 30 individual parts in 3 sentences or less for each step. The overall process involves disassembling the governor housing, fuel injection pump housing, and various internal components and installing them in the reverse order.
Similar to Caterpillar Cat 623E WHEEL SCRAPER (Prefix 5SG) Service Repair Manual Instant Download 7.pdf (20)
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
1. Product: WHEEL SCRAPER
Model: 623E WHEEL SCRAPER 5SG
Configuration: 623F Wheel Tractor-Scraper 5SG00480-UP (MACHINE) POWERED BY 3406C Engine
Disassembly and Assembly
3406C DIESEL ENGINES FOR CATERPILLAR BUILT MACHINES
Media Number -SENR6409-02 Publication Date -01/07/2006 Date Updated -19/05/2015
SENR64090008
Governor
SMCS - 1264-015; 1264-016
Disassemble Governor
*Part of 6V4095 Pump and Governor Reconditioning Tool Group.
IN
Start By:
a. remove fuel injection pump housing and governor
b. remove fuel transfer pump
NOTE: If it is desired to only remove the governor so the fuel injection pump housing can be
disassembled, do only steps 1, 2, 3, 16, 22, 25, 26, 27, 28, 32, 34 and 37.
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
2. 1. Put the fuel injection pump housing and governor in position on Tool (A).
2. Remove the bolts, fuel ratio control (1) and shutoff solenoid (2) from rear governor housing (3).
3. Remove the bolts, rear governor housing (3) and the gasket from the front governor housing.
4. Remove governor spring (4), the two wave washers, one flat washer and the seat from the guide
in the rear governor housing.
5. Remove bolt (5) that holds lever assembly (6) to the shaft assembly.
NOTE: There is a key in the slot groove of the shaft assembly that must be removed before the
shaft assembly is removed from the rear governor housing.
6. Remove shaft assembly (7), lever (6) and lever (8) from the rear governor housing.
NOTE: Put an alignment mark on lever (9) for correct assembly purposes.
7. Remove bolt (10), lever assembly (9) and spring (11) from shaft assembly (7).
2/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. 8. Remove plug (12) and lip-type seal (13) from the housing.
NOTE: Spacers (14) and (16) are different sizes. Make sure they are assembled in the correct
position.
9. Use needle nose pliers, and remove the shaft. Remove spacer (14), lever (15) and spacer (16)
from the governor housing.
10. Remove two setscrews and locknuts (17) if necessary.
11. Release spring (18) from the notch in the housing. Remove snap ring (19), and remove shaft
(20) from the housing. Remove lever (21) and spring (18).
3/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. 12. Remove liptype seal (22) from the housing.
13. If necessary, remove the screws, cover (23) and the gasket from the governor housing.
14. Remove high idle cover (24) and three O-ring seals (25).
15. Remove liptype seal (26), dashpot valve (27), fitting (25), insulator and high idle adjustment
(28) from the rear housing.
4/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. 16. Remove two bolts (29), housing (30) and the gasket from the fuel pump housing.
17. Remove bolts (31), and remove torque control group (32) from the block.
NOTICE
Depending on the different engine applications, torque control groups
will vary. Inspect all parts for wear and damage, and make a note of
the correct sequence of the parts for assembly purposes.
NOTE: For additional information, see Specifications Manual SENR6470.
18. Remove the bolts and block (33) for the full load stop from the housing.
19. Remove the bolt that holds collar (35) to bolt (36).
20. Remove collar (35) and spring (34) from bolt (36). Remove bolt (36) from the block.
21. If necessary, remove the stop screw and the power setting screw from collar (35).
5/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. NOTE: It may be necessary to turn the piston to remove the servo from the rack.
22. Remove the three bolts and governor servo (37) from the fuel injection pump housing.
23. Remove lockring (43), seat (42), spring (41) and sleeve (40) from valve (39). Remove lockring
(38) from the groove in the center of valve (39).
24. Remove sleeve (44), valve (45) and piston (46) from the governor servo. Remove O-ring seal
(50) from sleeve (44). Do not remove pin (47). If pin (47) and lever (48) or cylinder (49) are worn
or damaged replace the assembly.
25. Use Tool (C) to hold spring (51) under compression so the ring on the governor shaft can be
removed.
26. Remove the ring, and carefully remove Tool (C).
27. Remove bearing (52), the sleeve and spring (51) from the governor shaft.
6/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. 28. Remove ring (53) and dashpot assembly (54) from the governor shaft.
29. Use Tool (B), and remove ring (60) from seat (57).
30. Remove ring (59) and spool (58) from seat (57).
31. Remove seat (57), and spring (56) from shield (55).
32. Remove spring (62), if equipped, and riser (61) from the governor shaft.
33. Remove ring (63), races (64) and bearing (65) from the riser.
7/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. 34. Remove the bolts and carrier assembly (66) from the fuel injection pump housing.
35. Remove dowels (68) and flyweights (69) from the carrier assembly.
36. Remove dowel (67) from the governor shaft, and remove the governor shaft from the carrier
assembly.
37. Remove races (70) and (72) and bearing (71) from the camshaft in the fuel injection pump
housing.
8/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Assemble Governor
*Pump and Governor Reconditioning Tool Group
9/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. 1. Put the fuel injection pump housing in position on Tool (A). Install race (3), bearing (2) and
race (1) on the end of the camshaft in the fuel injection pump housing.
2. Put flyweights (5) in position on carrier assembly (4), and install dowels (6) to hold the
flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.230 mm
(.0004 to .0090 in) end play.
3. Install governor shaft (7) on carrier assembly (4).
4. Install dowel (8) in governor shaft (7), and slide carrier assembly (4) down on the governor
shaft until dowel (8) fits into the slot in the carrier assembly.
5. Install carrier assembly (4) on the end of the camshaft.
6. Install race (12), bearing (11), race (10) and ring (9) on riser (13).
10/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. 7. Install riser (13) and spring (14), if equipped, on the governor shaft.
8. Install spool (18) and ring (19) on seat (17), and use Tool (B) to install ring (20) to hold them in
position.
9. Install seat (17) on spring (16) and spring (16) on shield (15).
10. Install dashpot assembly (21) on the governor shaft.
11. Install ring (22) in the groove on the governor shaft. Install sleeve (23), spring (25), the sleeve
and bearing (24) on the governor shaft.
11/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. 12. Use Tool (C) to hold spring (25) under compression, and install the ring in the groove on the
governor shaft.
13. Install O-ring seal (26) on sleeve (27). Install piston (29) and sleeve (27) in the governor servo
as shown.
14. Install valve (28) in the governor servo as shown.
15. Install lockring (33) in the groove near the center of valve (28). Put sleeve (34), spring broken
link spring (35) and seat (36) in position on valve (28), and install lockring (37) to hold them in
place.
16. Put governor servo (30) in position on the fuel injection pump housing with piston (29)
engaged over the rack. Make sure the lever is engaged in the slot groove of riser (13).
12/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. 17. If dowel (43) was removed, install it in block (44) 31 ± 0.5 mm (1.22 ± .02 in) above the
outside surface of the block.
18. Install bolt (45) in block (44) and spring (38) on bolt (45).
19. Install stop screw (40) and the locknut on collar (42). Install power setting screw (41) and the
locknut on the collar.
20. Install collar (42) on bolt (45). Make an alignment of the hole in the collar with the notch in
bolt (45), and install bolt (39).
21. If the dowels that align block (44) with the front governor housing were removed, install them
4.0 ± 0.5 mm (.16 ± .02 in) above the outside surface of the front governor housing.
22. Put block (44) in position on the front governor housing with the holes in the block in
alignment with dowels in the front governor housing.
23. Install dowels (46) in the front governor housing 6.0 ± 0.5 mm (.24 ± .02 in) above the outside
surface of the front governor housing.
24. Assemble torque spring group (47) in the correct sequence, and install it on the block.
13/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. To avoid possible personal injury and damage to the engine when front
governor housing (48) is installed on the fuel injection pump housing,
make sure the flange on bolt (45) is behind the shield of the dashpot. If
the flange on the bolt is installed on the wrong side of the shield, the
riser in the governor will be held in the maximum fuel delivery position.
25. Install the gasket and front governor housing (48) on the fuel injection pump housing. Make
sure the flange on bolt (45) is behind the shield of dashpot (21).
26. Check the seal on dashpot valve (51) for damage or wear, and make a replacement if
necessary.
27. Install dashpot valve (51), insulator (49), fitting (50) high idle screw (52) and the locknut in
rear governor housing (53). Tighten insulator (49) to a torque of 4.5 ± 0.5 N·m (40 ± 4.4 lb in).
28. Use Tool (D), and install seal (54) with the lip of the seal down as shown. Put clean engine oil
on the lip of the seal. Install high idle screw cover (55) and O-ring seal (56).
14/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. 29. Install the liptype seals in housing (53) with Tool (D) as shown.
30. Install the gasket and cover (57) in the governor housing.
31. Put clip (60) in position on shaft (61), and install shaft (61) into the housing through spring
(59) and lever (58). Put the key in the lever in alignment with the keyway in the shaft.
32. Install clip (62) on the shaft, and install screw (63) and the locknut on the lever. Put the end of
the spring in position in the notch in the housing as shown.
15/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. 33. Install screws (64) and locknuts (65) on lever assembly (66). Tighten locknuts (65) to a torque
of 1.70 ± 0.25 N·m (15 ± 3 lb in).
34. Install shaft (68) in the housing. Install long spacer (67), lever assembly (66) and the short
spacer on shaft (68).
35. Check the condition of the O-ring seal on the plug. Lubricate the O-ring seal with clean engine
oil, and install the plug to hold shaft (68) in position.
36. Install lever assembly (72) on shaft assembly (73). Be sure the alignment marks on the
components are in alignment with each other.
37. Install shaft assembly (73) into the housing. Put washer (71) and lever (74) in position on the
shaft assembly. Put key (70) in the key slot on shaft assembly (73), and install lever (69) over the
key on the shaft assembly. Align the bolt hole in lever (69) with groove (75) in the shaft assembly,
and install the bolt.
38. Install seat (76), wave washer (78), washer (79), wave washer (80) and spring (81) on guide
(77).
To avoid possible personal injury and damage to the engine when rear
governor housing (53) in installed on the fuel injection pump housing,
16/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. make sure the flyweights are toward the fuel injection pump housing. If
the flyweights are extended out too far, the riser in the governor will be
held in the maximum fuel delivery position.
39. Install gasket (82) and rear governor housing (53) on the front governor housing.
40. Make the governor adjustments. See the topic "Fuel Ratio Control & Governor Check" in the
System Operation Testing & Adjusting Manual, Form No. SENR6471.
41. Put fuel ratio control (83) in position. Make sure the flange on the end of the fuel ratio control
is behind the slot in lever assembly (66). See Illustration B88652P1.
42. Hold the control lever in the fuel off position, and install shutoff solenoid (84).
43. Make an adjustment to the fuel ratio control. See the topic "Fuel Ratio Control And Governor
Check" in the System Operation Testing & Adjusting Manual, Form No. SENR6471.
End By:
a. install fuel transfer pump
b. install fuel injection pump housing and governor
Fri Dec 24 18:02:33 UTC+0800 2021
17/18(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Product: WHEEL SCRAPER
Model: 623E WHEEL SCRAPER 5SG
Configuration: 623F Wheel Tractor-Scraper 5SG00480-UP (MACHINE) POWERED BY 3406C Engine
Disassembly and Assembly
3406C DIESEL ENGINES FOR CATERPILLAR BUILT MACHINES
Media Number -SENR6409-02 Publication Date -01/07/2006 Date Updated -19/05/2015
SENR64090009
Fuel Injection Pumps
SMCS - 1251-011; 1251-012; 1251-017
Remove Fuel Injection Pumps
Start By:
a. remove fuel injection lines
1. Remove the plug, and move the race until Tool (A) can be installed to hold the rack in the center
position. The rack must be in the center position to remove the fuel injection pumps.
To prevent possible personal injury carefully follow the steps below.
1/6(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. 2. Put Tool (B), except for the 8T5287 Wrench, in position on the fuel pump housing as shown.
Lower the handle to center the adjusting screw with the fuel line seat. With the handle down in the
locked position, the adjusting screw must just be in contact with fuel line seat (1). If force is needed
to lower the handle or there is a gap, remove the tooling, and make an adjustment to the screw.
3. Loosen bushing (2) 1/4 of a turn.
4. Put Tool (B) in position on the pump housing with the handle down in the locked position as
shown.
5. Remove bushing (2) from the pump housing.
6. Carefully and slowly lift the handle to release the spring force. Remove the tooling.
7. Install Tool (C) on fuel pump (4) as shown.
8. Remove seal (3) and fuel pump (4) from the fuel pump housing.
9. Remove spacers (5) from the pump housing.
NOTE: There must be a pump installed on either side of the pump to be removed to install Tool (B).
If there is no pump, take a pump already removed, and remove the spring so there will be no spring
force, and install it in the pump housing. See Install Fuel Pump.
NOTE: Spacers (5) are the same thickness for each fuel injection pump so they can be mixed. The
fuel injection pump plungers and barrels are sets and cannot be mixed.
Install Fuel Injection Pumps
2/6(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. 1. Install spacers (5) in the fuel pump housing.
2. Move the rack until Tool (A) can be installed to hold the rack in the center position. The rack
must be in the center position to install the fuel injection pumps.
3. Install a fuel pump without its spring so that Tool (B) can be installed. See Step 5 for correct fuel
pump installation.
4. Install Tool (C) on the bonnet of the fuel pump as shown.
5. Install the fuel pump in the pump housing with the saw cut (slot) (9) in the gear in alignment with
small pin (6) in the lifter assembly and groove (8) in the barrel in alignment with large pin (7) in the
pump housing.
3/6(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. 6. Install the seal and bushing (2) on the fuel pump.
7. Put Tool (B) in position on the fuel pump housing as shown.
8. Lower the handle slowly and carefully. If the fuel pump is not installed correctly, the handle will
not go all the way down. Do not try to use force on it. Remove and install the tooling and the fuel
pump again.
9. Make sure the seal is in its correct position, and start to tighten bushing (2). Remove the tooling,
and tighten the bushing to a torque of 260 ± 15 N·m (190 ± 10 lb ft). Back off 180 degrees and
tighten the bushing again to a torque of 260 ± 15 N·m (190 ± 10 lb ft).
Typical Example
10. After each fuel pump has been installed, follow the steps below to check total race travel to
make sure each pump has been installed correctly.
a. Install Tool (D) on the fuel pump housing as shown and zero the dial indicator.
b. Remove Tool (A) from the fuel pump housing.
c. Move rack (10) in and out of the fuel pump housing to measure rack travel. Rack travel is
approximately 9.62 mm (.379 in) in the plus (full fuel) direction and 10.40 mm (.410 in) in the
minus (shutoff) direction. If this measurement is not obtained, center the rack, install Tool (A), and
remove and install the fuel pump again.
NOTE: One tooth off and rack travel is approximately 6.35 to 6.82 mm (.250 to .269 in) in the plus
direction and 7.02 to 7.05 mm (.276 to .278 in) in the minus direction.
End By:
a. install fuel injection lines
Disassemble & Assemble Fuel Injection Pumps
See SMHS8378 for the correct tool usage.
Start By:
4/6(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. a. remove fuel injection pumps
NOTICE
Be careful when the injection pumps are disassembled. Do not damage
the surfaces of the plungers, barrels and bonnets. Any scratches will
cause leakage inside the fuel injection pump. The plunger and barrel
for each pump are made as a set. Do not put the plunger of one pump
in the barrel of another pump. If one part has wear, install a complete
new pump assembly. Be careful when the plunger is put into the bore
of the barrel.
NOTE: Do not remove the gear from the plunger. The gear and plunger are assembled and adjusted
at the factory.
1. Pull plunger (4) and washer (3) out of barrel (1) and spring (2).
2. Remove spring (2) from barrel (1).
3. Use the following procedure to put the fuel pump in position on Tool (A):
a. Select the correct turret position.
b. Place a barrel assembly into the turret.
5/6(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. c. Loosen the nut on the clamp.
d. Adjust clamp end (6) until the bonnet is almost touching the barrel when the clamp handle is in
the locked position.
e. Tighten the nut on the clamp.
4. Use Tool (B) to expand ring (5), and carefully lift it off the fuel pump.
5. Slowly release the clamp handle of Tool (A), and remove the lockring.
6. Remove bonnet (7), spring (8) and valve (9) from barrel (1).
NOTE: The following steps are for assembly of the fuel injection pumps.
NOTICE
Put clean fuel on all parts during assembly.
7. Put spring (8) and valve (9) in bonnet (7).
8. Put bonnet (7) barrel (1) and ring (5) in position on Tool (A).
9. Put the barrel assembly in position on Tool (A). Lower the handle on Tool group (A) to hold the
fuel pump together.
10. Use Tool (B), and lower ring (5) on to the barrel and the bonnet to hold them together.
11. Remove the barrel assembly from Tool (B).
12. Install spring (2) on barrel (1).
13. Install washer (3) on plunger (4). Make sure the spring seat on the washer is away from the gear
on the plunger.
14. Install plunger (4) in barrel (1). Make sure spring (2) is engaged in the spring seat on washer (3).
End By:
a. install fuel injection pumps
6/6(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Product: WHEEL SCRAPER
Model: 623E WHEEL SCRAPER 5SG
Configuration: 623F Wheel Tractor-Scraper 5SG00480-UP (MACHINE) POWERED BY 3406C Engine
Disassembly and Assembly
3406C DIESEL ENGINES FOR CATERPILLAR BUILT MACHINES
Media Number -SENR6409-02 Publication Date -01/07/2006 Date Updated -19/05/2015
SENR64090010
Fuel Injection Pump Housing
SMCS - 1253-015; 1253-016
Disassemble Fuel Injection Pump Housing
Start By:
a. disassemble governor
b. remove fuel injection pumps
1. Remove the six lifters from the fuel pump housing.
2. Remove rack (1) and camshaft (2) from the fuel pump housing. If necessary, use a soft hammer
to push the camshaft out the governor end.
1/5(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. 3. Use Tool (A) and remove the three camshaft bearings from the fuel pump housing.
4. Remove rack bearing (4) and the other rack bearing from the fuel pump housing.
5. Remove dowel (3) from the fuel pump housing.
6. Remove bolts (6), cover (5) and the gasket from the fuel pump housing.
Assemble Fuel Injection Pump Housing
2/5(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. 1. Install gasket (7) and cover (5) on the side of the fuel pump housing.
2. Use Tool (B) and install the D shaped rack bearing into the governor and fuel pump drive side
of the fuel pump housing 87.0 ± 0.5 mm (3.42 ± .02 in) from outside surface (X).
3. The inside flat diameter after assembly must be 11.178 ± 0.050 mm (.440 ± .002 in) and the
inside large diameter must be 12.767 ± 0.058 mm (.503 ± .002 in).
4. Install dowel (3) in the fuel pump housing 6.0 ± 0.5 (.24 ± .02 in) above the outside surface.
5. Use Tool (C) and install the rack bearing into the fuel pump housing 7.16 ± 0.13 mm (.282
± .005 in) below the surface of the pump housing.
6. The inside diameter of the bearing after assembly must be 12.746 ± 0.045 (.502 ± .002 in).
7. Use Tool (A) and install the three camshaft bearings in the fuel pump housing with the oil holes
in the bearings 30 ± 3 degrees from the horizontal center line toward the plugged holes in the fuel
pump housing.
3/5(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. 8. The inside diameter of all three bearings after assembly must be 68.399 ± 0.038 mm (2.6905
± .0015 in).
9. Make sure bearing (8) on the governor and fuel pump drive is installed 1.0 ± 0.5 mm (.04 ± .02
in) below surface (Y).
10. Make sure middle bearing (9) is 218 ± 0.3 mm (8.6 ± .01 in) below surface (Y).
11. Make sure bearing (10) governor side is 1.00 ± 0.25 mm (.040 ± .010 in) below the outside
surface.
12. Remove the plugs from the side of the fuel pump housing. The oil holes in the bearings must
in alignment with holes (11) in the fuel pump housing. If the bearings are not in alignment,
remove them and install again.
13. Make an alignment of rack (1) and install it in the fuel pump housing.
14. Install the six lifters in the fuel pump housing. Make sure the pins in the lifter are on the same
side as the dowels in the fuel pump housing.
End By:
a. install fuel injection pumps
b. assemble governor
4/5(W)
w
2021/12/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...