This document provides installation instructions for installing a swivel on an excavator. It involves attaching lifting tools to the swivel, installing fittings and hoses, and securing the swivel in place with bolts while applying the proper torque. Cleanliness is important during installation to prevent contamination. The document also specifies required tools and safety procedures like releasing hydraulic pressure before disassembly.
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor, and tightening bolts. Safety precautions are mentioned such as releasing hydraulic pressure before disassembly and containing fluids properly. Required tools include lifting brackets, bolts, washers, and vacuum caps.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjskemdme
The document provides instructions for assembling an excavator swivel joint. It describes cleaning the parts thoroughly before assembly. It details installing new seals and O-rings on the outside housing and rotor. The rotor and outside housing are joined using bolts and washers, and the assembly is then attached to the excavator with hoses and fittings. Proper cleaning and installation of seals are important to prevent contamination issues.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
The document provides instructions for assembling a hydraulic lockout control. It describes 17 steps to assemble a piston motor, including installing bearings, seals, springs, and retaining rings. It also outlines 5 steps to disassemble a hydraulic lockout control, such as removing pins and springs. The assembly process is then described in 6 steps, including installing springs, pins, and lever assemblies. Personal injury warnings are provided throughout.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 336 d l excavator (prefix myg) service repair manual (myg0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
Bomag bw138 ac single tandem vibratory roller service repair manualpfiskdmjekm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 125 ADH, BW 135 AD, BW 138 AD, BW 138 AC. It includes technical specifications, safety information, descriptions of controls, operating procedures, maintenance schedules and procedures, and troubleshooting tips. The document is intended for operators and maintenance personnel and aims to ensure safe and proper use of the machines.
Caterpillar cat 385 c l mh excavator (prefix waw) service repair manual (waw0...fujskekfmsme
This document provides instructions for removing and installing fuel system components on a 385C Material Handler excavator powered by a C-18 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing and installing the fuel transfer pump
- Removing the electronic unit injectors
The instructions include safety notices and illustrations showing the component locations and part names.
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor, and tightening bolts. Safety precautions are mentioned such as releasing hydraulic pressure before disassembly and containing fluids properly. Required tools include lifting brackets, bolts, washers, and vacuum caps.
Caterpillar cat 336 d l excavator (prefix lmg) service repair manual (lmg0000...fjskemdme
The document provides instructions for assembling an excavator swivel joint. It describes cleaning the parts thoroughly before assembly. It details installing new seals and O-rings on the outside housing and rotor. The rotor and outside housing are joined using bolts and washers, and the assembly is then attached to the excavator with hoses and fittings. Proper cleaning and installation of seals are important to prevent contamination issues.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
The document provides instructions for assembling a hydraulic lockout control. It describes 17 steps to assemble a piston motor, including installing bearings, seals, springs, and retaining rings. It also outlines 5 steps to disassemble a hydraulic lockout control, such as removing pins and springs. The assembly process is then described in 6 steps, including installing springs, pins, and lever assemblies. Personal injury warnings are provided throughout.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 336 d l excavator (prefix myg) service repair manual (myg0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
Bomag bw138 ac single tandem vibratory roller service repair manualpfiskdmjekm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 125 ADH, BW 135 AD, BW 138 AD, BW 138 AC. It includes technical specifications, safety information, descriptions of controls, operating procedures, maintenance schedules and procedures, and troubleshooting tips. The document is intended for operators and maintenance personnel and aims to ensure safe and proper use of the machines.
Caterpillar cat 385 c l mh excavator (prefix waw) service repair manual (waw0...fujskekfmsme
This document provides instructions for removing and installing fuel system components on a 385C Material Handler excavator powered by a C-18 engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing and installing the fuel transfer pump
- Removing the electronic unit injectors
The instructions include safety notices and illustrations showing the component locations and part names.
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning and inspecting parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor using bolts and washers, and installing the assembled swivel on the excavator using lifting tools and bolts. Safety precautions are provided to contain hydraulic fluids and properly dispose of them. Required tools include vacuum caps, link brackets, bolts, washers, and a transmission repair stand.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fjjskekdmmem
This document provides instructions for installing a swivel on an excavator. It describes using lifting devices and link brackets to position the swivel. The instructions specify cleaning and lubricating O-rings before installing the swivel housing over the rotor. Bolts, washers and retainers are then used to hold the parts together. Finally, the swivel is tested for leaks with shop air pressure before being fully installed on the excavator.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning and inspecting parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor using bolts and washers, and installing the assembled swivel on the excavator using lifting tools and bolts. Safety precautions are provided to contain hydraulic fluids and properly dispose of them. Required tools include lifting devices, bolts, washers, and sealing components.
The document provides instructions for installing a swivel on an excavator. It includes:
- Attaching lifting equipment to the swivel which weighs 45 kg.
- Installing bolts and a retainer to mount the swivel.
- Connecting hydraulic hoses and fittings.
- Installing covers and bolts to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...fjjskekdmmem
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The assembly procedure instructs to clean parts thoroughly before assembly. Parts are to be positioned and bolted together in the correct order. O-rings and seals are installed in their proper locations. Once assembled, the swivel is installed on the excavator using lifting devices and bolted into place. Hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fjjskmdmem
The document provides instructions for assembling and disassembling a swivel component for an excavator. It describes:
1) How to disassemble the swivel by removing bolts, washers, covers and seals from the outside housing and rotor using specialized tools.
2) How to assemble the swivel by cleaning all parts, placing seals on the outside housing and rotor, and installing the outside housing and rotor together using bolts, washers and a retainer.
3) The importance of cleanliness during assembly to prevent contaminants from causing wear and failure of components.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes removing the hydraulic tank cap and attaching a vacuum tool to drain fluid from the system. The swivel is then positioned and bolted into place, and hoses and fittings are reconnected. Finally, the hydraulic tank cap is replaced and the system is refilled and checked for leaks. The process involves lifting and positioning heavy components and taking precautions to contain hydraulic fluids.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper order. It also provides disassembly instructions for a final drive in 13 steps, removing components like bolts, gears, and covers. Installation requires cleaning, applying sealant, and torquing bolts to specified values.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It describes 27 steps to disassemble the motor by removing components like the motor head, springs, brake piston, rotating assembly, bearings and seals. It then describes 28 steps for reassembling the motor components in reverse order, making sure to align parts properly, apply lubricants to seals and mating surfaces, and torque bolts to the specified values. The proper procedure is important to safely release spring forces and prevent damage during removal and installation of parts.
More Related Content
Similar to Caterpillar cat 336 d l excavator (prefix m3m) service repair manual (m3m00001 and up)
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning and inspecting parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor using bolts and washers, and installing the assembled swivel on the excavator using lifting tools and bolts. Safety precautions are provided to contain hydraulic fluids and properly dispose of them. Required tools include vacuum caps, link brackets, bolts, washers, and a transmission repair stand.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fjjskekdmmem
This document provides instructions for installing a swivel on an excavator. It describes using lifting devices and link brackets to position the swivel. The instructions specify cleaning and lubricating O-rings before installing the swivel housing over the rotor. Bolts, washers and retainers are then used to hold the parts together. Finally, the swivel is tested for leaks with shop air pressure before being fully installed on the excavator.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It outlines 11 steps including cleaning and inspecting parts, positioning the swivel using lifting tools, installing seals and O-rings, attaching the outer housing and rotor using bolts and washers, and installing the assembled swivel on the excavator using lifting tools and bolts. Safety precautions are provided to contain hydraulic fluids and properly dispose of them. Required tools include lifting devices, bolts, washers, and sealing components.
The document provides instructions for installing a swivel on an excavator. It includes:
- Attaching lifting equipment to the swivel which weighs 45 kg.
- Installing bolts and a retainer to mount the swivel.
- Connecting hydraulic hoses and fittings.
- Installing covers and bolts to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...fjjskekdmmem
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The assembly procedure instructs to clean parts thoroughly before assembly. Parts are to be positioned and bolted together in the correct order. O-rings and seals are installed in their proper locations. Once assembled, the swivel is installed on the excavator using lifting devices and bolted into place. Hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fjjskmdmem
The document provides instructions for assembling and disassembling a swivel component for an excavator. It describes:
1) How to disassemble the swivel by removing bolts, washers, covers and seals from the outside housing and rotor using specialized tools.
2) How to assemble the swivel by cleaning all parts, placing seals on the outside housing and rotor, and installing the outside housing and rotor together using bolts, washers and a retainer.
3) The importance of cleanliness during assembly to prevent contaminants from causing wear and failure of components.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes removing the hydraulic tank cap and attaching a vacuum tool to drain fluid from the system. The swivel is then positioned and bolted into place, and hoses and fittings are reconnected. Finally, the hydraulic tank cap is replaced and the system is refilled and checked for leaks. The process involves lifting and positioning heavy components and taking precautions to contain hydraulic fluids.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
Similar to Caterpillar cat 336 d l excavator (prefix m3m) service repair manual (m3m00001 and up) (10)
Caterpillar cat 336 f excavator (prefix tje) service repair manual (tje00001 ...fhsjekdmme
The document provides instructions for disassembling the travel motor of an excavator model 336F. It lists 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix ljy) service repair manual (ljy00001 ...fhsjekdmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f excavator (prefix kcs) service repair manual (kcs00001 ...fhsjekdmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and using isopropyl alcohol.
Caterpillar cat 336 e lnh excavator (prefix ssl) service repair manual (ssl00...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive assembly, including removing hoses, bolts, seals and other parts. Precautions are given regarding weight of components and proper torque specifications for reinstallation. Detailed illustrations accompany each step of disassembly and assembly.
Caterpillar cat 336 e lnh excavator (prefix rza) service repair manual (rza00...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lnh excavator (prefix gny) service repair manual (gny00...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fhsjekdmme
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor, including disconnecting hoses and removing mounting bolts. It also explains how to disassemble the final drive by removing the cover, planetary gears, and other internal components. Precise steps and required tools are listed to correctly take apart and rebuild the final drive and travel motor.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fhsjekdmme
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly process involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix jea) service repair manual (jea000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper lubrication and torque specifications. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fhsjekdmme
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper order. It also provides disassembly instructions for a final drive in 13 steps, removing components like bolts, gears, and covers. Installation requires cleaning, applying sealant, and torquing bolts to specified values.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It describes 27 steps to disassemble the motor by removing components like the motor head, springs, brake piston, rotating assembly, bearings and seals. It then describes 28 steps for reassembling the motor components in reverse order, making sure to align parts properly, apply lubricants to seals and mating surfaces, and torque bolts to the specified values. The proper procedure is important to safely release spring forces and prevent damage during removal and installation of parts.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fhsjekdmme
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring forces or pressurized components.
Caterpillar cat 336 d2 l excavator (prefix hbk) service repair manual (hbk000...fhsjekdmme
This document provides disassembly instructions for a travel motor on 336D2, 336D2 L, and 336D2 GC excavators. The procedure involves 27 steps to disassemble the various components of the travel motor, including removing the head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Tools and safety precautions are listed. Alignment marks and noting component locations are emphasized to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix fbt) service repair manual (fbt000...fhsjekdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar cat 336 d2 l excavator (prefix faj) service repair manual (faj000...fhsjekdmme
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pullers, pry bars, and seal removal tools.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07188136
Final Drive and Travel Motor - Install
SMCS - 4050-012; 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 439-3938 Link Bracket 1
D - Loctite C5A Copper Anti-Seize -
Note: Check the O-ring seals for wear or for damage. Replace the O-ring seals, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01181921
1. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
2. Position travel motor (11). Install bolts (12) that mount travel motor (11) to final drive (13).
2/5
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01181917
3. Install O-ring seals (10) and (9).
Illustration 3 g01181914
4. Install counterbalance valve (8) and bolts (7).
Illustration 4 g01181911
3/5
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01182266
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb).
6. Carefully position final drive and travel motor (5). Apply Tooling (D) to the threads of bolts
(6).
7. Tighten bolts (6) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
Illustration 6 g01223711
8. Install fitting (4). Connect hose assemblies (3).
4/5
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00944947
9. Remove Tooling (A). Install the cap onto the hydraulic tank.
10. Fill the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricant Viscosities
and Refill Capacities".
Illustration 8 g01223707
11. Install cover (2) and bolts (1). Tighten bolts (1) to a torque of 130 ± 10 N·m (96 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:30:28 UTC+0800 2020
5/5
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434256
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01209599
1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216069
2. Disconnect hose assemblies (1), (2), and (3). Remove support (4).
Illustration 3 g01216082
2/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 3. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Remove bolts (6) and retainer (8). Remove clamp (7) and boot
(5).
Illustration 4 g01216099
4. Remove bolts (10) and covers (11).
Illustration 5 g01216098
5. Disconnect hose assemblies (15). Disconnect fitting (16). Disconnect hose assemblies (12).
Remove fittings (14). Remove bolts (13). Remove swivel (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:31:23 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02568407
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-3822 Bolt 2
6V-5839 Washer 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Thoroughly clean the outside of the swivel joint prior to disassembly.
Illustration 1 g00633843
Illustration 2 g00633841
2. Use a suitable lifting device to position the swivel joint onto Tooling (B). Fasten the swivel joint to
Tooling (B), as shown. The weight of the swivel joint is approximately 43 kg (95 lb).
3. Remove bolts (1), washers (2), and cover (3) from outside housing (8).
4. Remove O-ring seal (7) from outside housing (8).
5. Remove bolts (4), washers (5), and retainer (6) from rotor (11).
2/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 6. Use Tooling (A) in order to separate the outside housing (8) from rotor (11). The weight of outside
housing (8) is approximately 20 kg (45 lb). The weight of rotor (11) is approximately 21 kg (46 lb).
7. Remove seals (9) from outside housing (8).
8. Remove O-ring seals (10) from the outside housing (8).
9. Remove plug (13). Remove O-ring seal (12) from plug (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:32:19 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02426337
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components,
if necessary.
1/2
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00633843
1. Install O-ring seal (12) on plug (13). Apply clean hydraulic oil on the seal. Install plug (13).
2. Install seals (9) and O-ring seals (10) into outside housing (8).
3. Carefully install outside housing (8) over rotor (11).
4. Install retainer (6), washers (5), and bolts (4). This holds the rotor (11) and the outside housing (8)
together.
5. Apply clean hydraulic oil on O-ring seal (7). Install the O-ring seal in the outside housing.
6. Install cover (3), washers (2), and bolts (1) that secure the cover.
7. Check the swivel joint for leaks. Plug the drain ports of the inside body. Apply shop air pressure in
the top of the swivel joint and check the swivel joint for leaks. The shop air pressure should be
between 0.2758 MPa (40 psi) and 0.4137 MPa (60 psi).
End By:
a. Install the swivel joint. Refer to Disassembly and Assembly, "Swivel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:33:15 UTC+0800 2020
2/2
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434356
Swivel - Install
SMCS - 5060-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Illustration 1 g01216082
1. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Position swivel (9). Install boot (5) and clamp (7). Install
retainer (8) and bolts (6).
1/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01216069
2. Connect hose assemblies (1), (2), and (3). Install support (4).
Illustration 3 g01216098
3. Install bolts (13). Install fittings (14). Install fitting (16). Connect hose assemblies (15).
Connect hose assemblies (14) and (12) to swivel (9).
Illustration 4 g01216099
4. Install covers (11) and bolts (10).
2/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g01209599
5. Remove Tooling (A).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:34:11 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434311
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Remove
SMCS - 5479-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes
for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g00690963
1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the
hydraulic system.
2/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01206719
2. Open door (1).
Illustration 3 g01216136
3. Disconnect harness assemblies (4).
4. Disconnect hose assemblies (2) and (3).
5. Remove bolts (5) and solenoid valve (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:35:07 UTC+0800 2020
3/3
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434312
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Install
SMCS - 5479-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01216136
1/2
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 1. Install solenoid valve (6) and bolts (5).
2. Connect hose assemblies (2) and (3).
3. Connect harness assemblies (4).
Illustration 2 g01206719
4. Close door (1).
Illustration 3 g00690963
5. Remove Tooling (A) from the hydraulic tank.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:36:03 UTC+0800 2020
2/2
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02413351
Swing Cushion Valve - Remove
SMCS - 5454-015
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Illustration 1 g01206252
1. Disconnect hose assemblies (1) and (2). Disconnect harness assembly (4). Remove bolts (3)
and remove swing cushion valve (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 28 00:36:59 UTC+0800 2020
1/1
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT M3M
Configuration: 336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02096925
Swing Cushion Valve - Disassemble - Fine Swing Solenoid
SMCS - 5454-015
Disassembly Procedure
Start By:
a. Remove the swing cushion valve. Refer to Disassembly and Assembly, "Swing Cushion
Valve - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
Illustration 1 g00702083
1. Remove O-ring seals (1) and (2) from the valve body.
2. Remove the fine swing solenoid, as follows.
1/4
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g00702084
a. Remove bolts (3).
b. Remove fine swing solenoid (4).
Illustration 3 g00702085
c. Remove O-ring seal (8), (6), (7), and (5).
3. Remove the relief valves, as follows.
Illustration 4 g00702097
2/4
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g00702102
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
a. Remove relief valve (9) from the valve body.
b. Remove spring (12), plunger (11), and ball valve (10) from relief valve (9).
Illustration 6 g00702106
c. Remove backup ring (13) and O-ring seal (14) from the relief valve.
4. Repeat Steps 3.a through 3.c for the remaining relief valve.
Fri Aug 28 00:37:55 UTC+0800 2020
3/4
336D & 336D L Mobile Hydraulic Power Units M3M00001-UP (MACHINE) POWE...
2020/8/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...