download service repair manual

1. 2004 STEERING
Power Steering Gear - Sequoia
COMPONENTS
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 1 © 2005 Mitchell Repair Information Company, LLC.
Microsoft
Tuesday, September 15, 2009 8:04:01 AM Page 1 © 2005 Mitchell Repair Information Company, LLC.

2. Fig. 1: Identifying Power Steering Gear Components (1 Of 3)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 2 © 2005 Mitchell Repair Information Company, LLC.

3. Fig. 2: Identifying Power Steering Gear Components (2 Of 3)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 3 © 2005 Mitchell Repair Information Company, LLC.

4. Fig. 3: Identifying Power Steering Gear Components (3 Of 3)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2. REMOVE STEERING WHEEL PAD (See REMOVAL )
3. REMOVE STEERING WHEEL (See REMOVAL )
4. DISCONNECT RH AND LH TIE ROD ENDS ( BALL JOINTS )
5. DISCONNECT NO. 2 INTERMEDIATE SHAFT ASSEMBLY (See REMOVAL )
6. DISCONNECT CLAMP PLATE
Remove the bolt and disconnect the clamp plate.
7. DISCONNECT PRESSURE FEED AND RETURN TUBES
Using SST, disconnect the tubes.
SST 09023-12700
8. REMOVE PS GEAR ASSEMBLY
a. Remove the bolt, nut and stud bolt from the bracket.
b. Remove the 2 set bolts, nut, washer and PS gear assembly.
9. REMOVE BRACKET AND GROMMET
NOTE: Remove the steering wheel assembly before the steering gear removal, because
there is possibility of breaking of the spiral cable.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 4 © 2005 Mitchell Repair Information Company, LLC.

5. Fig. 4: Locating SST
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
DISASSEMBLY
1. REMOVE 2 TURN PRESSURE TUBES
a. Using SST, remove the 2 turn pressure tubes.
SST 09023-38400
b. Remove the 4 O-rings from the tubes.
NOTE: When using a vise, do not overtighten it.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 5 © 2005 Mitchell Repair Information Company, LLC.

6. Fig. 5: Removing Turn Pressure Tubes
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. SECURE PS GEAR ASSEMBLY IN VISE
Using SST, 2 bolts and nuts, secure the gear assembly in a vise, as shown in the illustration.
SST 09612-00012
Reference:
Bolt: 90105-10346
Nut: 90170-10198
NOTE: Use 2 of the same type of SST.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 6 © 2005 Mitchell Repair Information Company, LLC.

7. 2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 7 © 2005 Mitchell Repair Information Company, LLC.

8. Fig. 6: Locating SST
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. REMOVE RH AND LH TIE ROD ENDS AND LOCK NUTS
a. Place matchmarks on the tie rod end, lock nut and rack end.
b. Loosen the lock nut, remove the tie rod end and lock nut.
c. Perform the same manner described above to the other side.
Fig. 7: Placing Matchmarks On Tie Rod End, Lock Nut & Rock End
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4. REMOVE RH AND LH CLIPS, RACK BOOTS AND CLAMPS
a. Using a screwdriver, loosen the 2 clamps.
b. Remove the 2 clips and boots.
NOTE: Mark the RH and LH boots.
NOTE: Be careful not to damage the boot.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 8 © 2005 Mitchell Repair Information Company, LLC.

9. Fig. 8: Loosening Boots Clamps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5. REMOVE RH AND LH RACK ENDS AND CLAW WASHERS
a. Using a screwdriver and hammer, unstake the washer.
NOTE: Avoid any impact on the steering rack.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 9 © 2005 Mitchell Repair Information Company, LLC.

10. Fig. 9: Unstaking Claw Washer
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Using a spanner, hold the steering rack steadily, and using SST, remove the rack end.
SST 09922-10010
c. Remove the washer from the rack end.
d. Perform the same manner described above to the other side.
NOTE: Mark the RH and LH rack ends.
NOTE: Use SST 09922-10010 in the direction shown in the illustration.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 10 © 2005 Mitchell Repair Information Company, LLC.

11. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

12. Fig. 10: Removing Rock End
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
6. REMOVE RACK GUIDE SPRING CAP LOCK NUT
Using SST, remove the lock nut.
SST 09922-10010
7. REMOVE RACK GUIDE SPRING CAP, RACK GUIDE SPRING AND RACK GUIDE SUB
ASSEMBLY
a. Using a hexagon wrench, remove the rack guide spring cap.
b. Remove the rack guide spring and rack guide sub-assembly.
NOTE: Use SST 09922-10010 in the direction shown in the illustration.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 11 © 2005 Mitchell Repair Information Company, LLC.

13. Fig. 11: Removing Rack Guide Spring Cap Lock Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8. REMOVE RACK HOUSING CAP
Using SST, remove the rack housing cap.
SST 09816-30010
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 12 © 2005 Mitchell Repair Information Company, LLC.

14. Fig. 12: Removing Rack Housing Cap
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
9. REMOVE SELF-SOCKING NUT
Using SST, stop the control valve shaft rotation, and remove the nut.
SST 09616-0001 1
10. REMOVE DUST COVER
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 13 © 2005 Mitchell Repair Information Company, LLC.

15. Fig. 13: Removing Self - Locking Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
11. REMOVE CONTROL VALVE HOUSING WITH CONTROL VALVE ASSEMBLY
a. Place matchmarks on the control valve housing and rack housing.
b. Remove the 2 bolts and control valve housing with control valve assembly attached.
c. Remove the gasket from the rack housing.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 14 © 2005 Mitchell Repair Information Company, LLC.

16. Fig. 14: Identifying Matchmarks
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
12. REMOVE CONTROL VALVE ASSEMBLY
a. To prevent oil seal lip damage, wind vinyl tape around the serrated part of the valve shaft.
b. Press out the valve assembly with the oil seal.
13. REMOVE OIL SEAL
Remove the oil seal from the control valve assembly.
NOTE:  Place a shop rag between the valve housing and the blocks.
 Be careful not to drop the valve assembly.
 Be careful not to damage the oil seal lip.
2004 Toyota Sequoia Limited
2004 STEERING Power Steering Gear - Sequoia
Microsoft
Tuesday, September 15, 2009 8:03:56 AM Page 15 © 2005 Mitchell Repair Information Company, LLC.