This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. Additionally, it provides instructions for removing and installing the engine oil filter base and engine oil cooler.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...tuzhiyou2
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, and engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new seals, filters, and coolers, checking for wear and contaminants, and ensuring proper lubrication. Safety notices are included to handle fluids and contain contaminants properly.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...qfyc504378
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Cautions are provided regarding containing fluids, collecting waste, and preventing rapid wear from contaminants.
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Safety notices are provided regarding containing fluids, collecting waste, and preventing contact with hot oil or components.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...lituo39419496
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...tuzhiyou2
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, and engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new seals, filters, and coolers, checking for wear and contaminants, and ensuring proper lubrication. Safety notices are included to handle fluids and contain contaminants properly.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...qfyc504378
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Cautions are provided regarding containing fluids, collecting waste, and preventing rapid wear from contaminants.
The document provides instructions for removing and installing valve stem seals, engine oil filter bases, engine oil coolers, and disassembling and assembling engine oil coolers on Caterpillar 3064 and 3066 engines. The procedures describe using various tools to remove old parts and install new parts, checking components for wear or damage, and ensuring parts are clean to prevent contamination. Safety notices are provided regarding containing fluids, collecting waste, and preventing contact with hot oil or components.
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...lituo39419496
The document provides instructions for removing and installing valve stem seals, engine oil filter base, and engine oil cooler on Caterpillar 3064 and 3066 engines. The removal procedures describe using tools to remove old parts and inspecting components. The installation procedures describe cleaning parts, applying oil, and securing components with bolts and washers.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...tuzhiyou2
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. New gaskets are also replaced.
1) The document provides instructions for installing the rocker shaft and pushrods on a Caterpillar 3054C engine. It describes cleaning and lubricating the parts, compressing the springs using a tool, and tightening the screws in a specific sequence.
2) The instructions then describe removing the cylinder head, which requires draining fluids and removing other engine components first. Dowel pins must be aligned during installation.
3) Reinstalling the cylinder head requires cleaning, torquing bolts in a sequence, and refilling fluids. Tools are used to install and correctly torque the bolts.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01150941
Inlet and Exhaust Valve Seals - Remove and Install
SMCS - 1104-010-SA
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00610601
Illustration 2 g00610605
1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide.
Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed
from cylinder head (4) .
Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed
in cylinder head (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
NOTICE
Keep all parts clean from contaminants.
2/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Contaminants may cause rapid wear and shortened component life.
Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into
contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem
with engine oil in order to ensure initial lubrication of the seal lip.
Illustration 3 g00610601
Illustration 4 g00610605
1. Place the new valve stem seal in position on the valve guide.
2. Use Tool (A) to assist in installing the new valve stem seal.
Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is
removed from the cylinder head (4) .
Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is
installed in the cylinder head (4) .
Note: After the valve stem seal is installed on the valve guide, ensure that the seal is
properly installed in the groove of the valve guide.
3/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:02 UTC+0800 2020
4/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565892
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813775
Illustration 2 g00813789
1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) .
2. Remove the bolts (1) and washers from the engine oil filter base (3) .
3. Remove engine oil filter base (3) from the engine.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
worn or damaged.
Illustration 3 g00813823
5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the
engine.
6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or
damaged.
7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged
components with replacement parts.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:58 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565969
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00813823
1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) .
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g00813789
2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
damaged.
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
3. Install the O-ring seals (4) on engine oil filter base (3) .
Illustration 3 g00813775
4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers.
5. Install the engine oil filter (2) to the engine oil filter base (3) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:20:54 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615275
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00611319
1. If necessary, remove bolt (1) and the washer from the cylinder head.
2. Remove oil tube assembly (dipstick) (2) from the cylinder block.
3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O-
ring seal is worn or damaged.
Illustration 2 g00611320
4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block.
The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers.
5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block.
Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged.
Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:21:49 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152039
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00618921
Illustration 2 g00611507
1. Remove four nuts (1) and the washers from the oil cooler core (3) .
2. Remove oil cooler core (3) from oil cooler cover (2) .
Note: Check the engine oil cooler core for cracks, clogging, and ruptures.
3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage.
Replace the gaskets, if necessary.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01152137
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00618921
Illustration 2 g00611507
1. Install two gaskets (4) onto the oil cooler core (3) .
2. Install the oil cooler cover (2) onto the oil cooler core (3) .
3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover.
4. Tighten the four nuts (1) .
End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:23:41 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615279
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611320
1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces
are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine
cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16
bolts and washers.
1/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g00611319
2. Install oil tube assembly (dipstick) (2) into the cylinder block.
Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation.
3. Install bolt (1) and the washer into the cylinder head.
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:24:37 UTC+0800 2020
2/2
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615285
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607236
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g00607247
1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side
of the cylinder block.
2. Remove the spring (3) and spring seat (4) from the cylinder block.
Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the
spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new
part.
Note: Check the cylinder block for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00607247
Illustration 4 g00607236
1. Install spring seat (4) and spring (3) in the cylinder block.
2. Install shim (2) and threaded plug (1) in the cylinder block.
3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb
ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary.
For more information, refer to Specifications, "Engine Oil Relief Valve".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:25:33 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615293
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00607679
1/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g00607688
1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) .
2. Remove shim (3) from the cylinder block (2) .
3. Remove spring (4) from the cylinder block (2) .
4. Remove spring seat (5) from the cylinder block (2) .
Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the
spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new
part.
Note: Check the cylinder block (2) for oil passages that are clogged.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00607688
Illustration 4 g00607679
1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) .
2. Install shim (3) and threaded plug (1) in the cylinder block (2) .
3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary.
For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication
System".
For more information, refer to Specifications, "Engine Oil Bypass Valve".
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:26:28 UTC+0800 2020
3/3
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much
for your reading.
Please click here to buy
After you pay.
Then, you can
download the complete
manual instantly.
No waiting.
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
Illustration 2 g00607770
2/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
Illustration 3 g00607857
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
Illustration 4 g00607885
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...