The document provides instructions for assembling a piston motor used in excavator models 336D2 and 336D2 L. It describes 17 steps to install various parts like bearings, seals, pins and plates. Safety warnings are included to properly handle parts under spring tension. The assembly ends by installing the piston motor and fan per other service manuals.
The document provides instructions for assembling and disassembling various components of an excavator, including:
1. Assembling the piston motor by installing various parts like bearings, seals, springs, and retaining rings in 17 steps.
2. Installing the assembled piston motor and fan motor assembly along with attaching bolts and bending locking tabs.
3. Disassembling the hydraulic lockout control by removing retaining rings, levers, springs, and pins over 5 steps.
4. Reassembling the hydraulic lockout control by reversing the disassembly steps over 6 steps.
5. Installing the assembled hydraulic lockout control along with bolts, screws, and attaching
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...zatao0179249295
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...luanxianshi27
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then explains installing the assembled piston motor and attaching a fan motor assembly. Finally, it outlines installing the hydraulic lockout control unit with bolts, screws, and a cable strap.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then details installing the assembled piston motor and attaching a fan motor assembly. Finally, it explains how to install the hydraulic lockout control unit with bolts and screws, and attaching a switch and cable strap.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...f8uesjdkdmdm
The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
The document provides instructions for assembling and disassembling various components of an excavator, including:
1. Assembling the piston motor by installing various parts like bearings, seals, springs, and retaining rings in 17 steps.
2. Installing the assembled piston motor and fan motor assembly along with attaching bolts and bending locking tabs.
3. Disassembling the hydraulic lockout control by removing retaining rings, levers, springs, and pins over 5 steps.
4. Reassembling the hydraulic lockout control by reversing the disassembly steps over 6 steps.
5. Installing the assembled hydraulic lockout control along with bolts, screws, and attaching
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...zatao0179249295
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...luanxianshi27
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then explains installing the assembled piston motor and attaching a fan motor assembly. Finally, it outlines installing the hydraulic lockout control unit with bolts, screws, and a cable strap.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then details installing the assembled piston motor and attaching a fan motor assembly. Finally, it explains how to install the hydraulic lockout control unit with bolts and screws, and attaching a switch and cable strap.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...f8uesjdkdmdm
The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, springs, and valves in the proper sequence.
3. Lifting the swing motor or drive using lifting brackets and removing bolts to separate the components.
Caterpillar Cat 326D2 L Excavator (Prefix KER) Service Repair Manual (KER0000...f8uesjdkdmdm
This document provides the disassembly procedure for a travel motor in 27 steps. It begins by cleaning the outside of the travel motor and fastening it vertically. The first steps include removing the head and various internal components like seals, springs, plates, and pistons. Later steps dismantle the rotating assembly, remove bearings from the shaft, and disassemble the barrel assembly. Throughout, care is taken to mark components for reinstallation in their original positions. Required tools are also listed.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f8uesjdkdmdm
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
1. The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2. The removal procedure includes disconnecting harness assemblies, removing bolts, and draining coolant from the cooling system.
3. The installation procedure specifies applying anti-seize compound to bolts and tightening them in a numerical sequence to the specified torques. Connecting harness assemblies and installing supports are also described.
Caterpillar Cat 326D2 L (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
This document provides instructions for disassembling a travel motor. It begins by having the technician clean and secure the travel motor vertically. They are instructed to mark the head and body for alignment during reassembly. Over 25 steps are then outlined to remove various components of the travel motor like the head, brake piston, plates, and barrel assembly. Throughout, technicians are warned to be careful not to damage parts and ensure components are reinstalled in their original positions.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and rotating assembly. The rotating assembly contains a shaft that requires removing retaining rings and bearing races using various tools. Piston assemblies are also removed from the barrel assembly after marking their positions.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Cleaning and marking the final drive assembly.
2. Removing the cover and gears using various tools.
3. Taking apart the carrier assemblies by removing pins, washers, and gears.
4. Using presses and hammers to separate additional components from the housing.
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals and housing cover. Corresponding assembly instructions are also provided, specifying the use of various tools and noting that all seals and gaskets must be replaced. Cleanliness is emphasized throughout the assembly process.
The document provides step-by-step instructions to disassemble a final drive on an excavator. It begins by removing the final drive from the machine and securing it to a repair stand. Various components like gears, shafts, seals and housings are then removed individually using an assortment of tools. Detailed illustrations accompany each step to show how to properly disassemble the final drive. Cleanliness is emphasized to prevent dirt from entering the mechanism during reassembly.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...f8uesjdkdmdm
The document provides instructions for removing and installing a lifter group on a Caterpillar C7 engine. It describes disconnecting related components like the rocker arms and pushrods. It then instructs removing bolts and side covers to access the lifter arms and shaft. Identification marks should be made on each lifter before removal to ensure proper reinstallation.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...f8uesjdkdmdm
This service repair manual provides instructions for repairing a 325D L excavator transmission. It details 33 steps for disassembling and assembling the transmission components. Cleanliness is important during repair. O-rings and seals should always be replaced. Various tools are used to install bearings, seals, gears, and other parts in the correct order. Proper torque specifications and safety precautions are noted throughout the process.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...f8uesjdkdmdm
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists the required tools and gives step-by-step instructions to disassemble the various components of the travel motor. Some key steps include removing the head from the motor body, extracting the brake piston, removing plates and discs, and taking apart the rotating assembly. Proper cleaning and replacement of seals is emphasized for reassembly.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Fasten the final drive assembly to a repair stand and remove the cover by taking out bolts and setscrews.
2) Remove additional components from the cover including a gear, check plate, and seals.
3) Clean all components thoroughly before disassembly to prevent dirt from entering during reassembly.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...f8uesjdkdmdm
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing by positioning parts and tightening bolts.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, springs, and valves in the proper sequence.
3. Lifting the swing motor or drive using lifting brackets and removing bolts to separate the components.
Caterpillar Cat 326D2 L Excavator (Prefix KER) Service Repair Manual (KER0000...f8uesjdkdmdm
This document provides the disassembly procedure for a travel motor in 27 steps. It begins by cleaning the outside of the travel motor and fastening it vertically. The first steps include removing the head and various internal components like seals, springs, plates, and pistons. Later steps dismantle the rotating assembly, remove bearings from the shaft, and disassemble the barrel assembly. Throughout, care is taken to mark components for reinstallation in their original positions. Required tools are also listed.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f8uesjdkdmdm
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
1. The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2. The removal procedure includes disconnecting harness assemblies, removing bolts, and draining coolant from the cooling system.
3. The installation procedure specifies applying anti-seize compound to bolts and tightening them in a numerical sequence to the specified torques. Connecting harness assemblies and installing supports are also described.
Caterpillar Cat 326D2 L (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
This document provides instructions for disassembling a travel motor. It begins by having the technician clean and secure the travel motor vertically. They are instructed to mark the head and body for alignment during reassembly. Over 25 steps are then outlined to remove various components of the travel motor like the head, brake piston, plates, and barrel assembly. Throughout, technicians are warned to be careful not to damage parts and ensure components are reinstalled in their original positions.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and rotating assembly. The rotating assembly contains a shaft that requires removing retaining rings and bearing races using various tools. Piston assemblies are also removed from the barrel assembly after marking their positions.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Cleaning and marking the final drive assembly.
2. Removing the cover and gears using various tools.
3. Taking apart the carrier assemblies by removing pins, washers, and gears.
4. Using presses and hammers to separate additional components from the housing.
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals and housing cover. Corresponding assembly instructions are also provided, specifying the use of various tools and noting that all seals and gaskets must be replaced. Cleanliness is emphasized throughout the assembly process.
The document provides step-by-step instructions to disassemble a final drive on an excavator. It begins by removing the final drive from the machine and securing it to a repair stand. Various components like gears, shafts, seals and housings are then removed individually using an assortment of tools. Detailed illustrations accompany each step to show how to properly disassemble the final drive. Cleanliness is emphasized to prevent dirt from entering the mechanism during reassembly.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...f8uesjdkdmdm
The document provides instructions for removing and installing a lifter group on a Caterpillar C7 engine. It describes disconnecting related components like the rocker arms and pushrods. It then instructs removing bolts and side covers to access the lifter arms and shaft. Identification marks should be made on each lifter before removal to ensure proper reinstallation.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...f8uesjdkdmdm
This service repair manual provides instructions for repairing a 325D L excavator transmission. It details 33 steps for disassembling and assembling the transmission components. Cleanliness is important during repair. O-rings and seals should always be replaced. Various tools are used to install bearings, seals, gears, and other parts in the correct order. Proper torque specifications and safety precautions are noted throughout the process.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...f8uesjdkdmdm
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists the required tools and gives step-by-step instructions to disassemble the various components of the travel motor. Some key steps include removing the head from the motor body, extracting the brake piston, removing plates and discs, and taking apart the rotating assembly. Proper cleaning and replacement of seals is emphasized for reassembly.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Fasten the final drive assembly to a repair stand and remove the cover by taking out bolts and setscrews.
2) Remove additional components from the cover including a gear, check plate, and seals.
3) Clean all components thoroughly before disassembly to prevent dirt from entering during reassembly.
Caterpillar Cat 325D L Excavator (Prefix KDG) Service Repair Manual (KDG00001...f8uesjdkdmdm
This document provides instructions for removing and installing various engine components on a Caterpillar C7 engine, including:
- Removing and installing the flywheel using lifting tools and bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller, and installing the new seal with an installer tool.
- Removing and installing the flywheel housing using lifting tools, bolts, and sealant on the mounting face.
- Removing the vibration damper and pulley by removing the drive belt and bolts, and installing by positioning parts and tightening bolts.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415453
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01207418
1. Use a suitable lifting device to install piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
2. Install bolts (6).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g01207416
3. Use a suitable lifting device to reposition fan motor assembly (4), as shown. The weight of
fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207415
4. Install hub (3) and bolts (2).
5. Bend locking tabs (1) over bolts (2).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 10 23:59:03 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02554917
Hydraulic Lockout Control - Remove
SMCS - 5001-011-LK
Removal Procedure
Illustration 1 g01187398
1. Remove screws (2) and panel (1).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01278781
2. Remove screws (6). Cut cable strap (8) and place switch (7) aside.
3. Remove bolt (4), bolt (5), and hydraulic lockout control (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 10 23:59:59 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378526
Hydraulic Lockout Control - Disassemble
SMCS - 5001-015-LK
Disassembly Procedure
Start By:
a. Remove the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Remove".
Illustration 1 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove retaining rings (1) and lever assembly (2).
2. Remove retaining ring (4), lever assembly (5), and spring (3).
Illustration 2 g01187383
3. Pull back cover (8) in order to remove pin (7) from pipe assembly (6).
Illustration 3 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 4. Remove pin (10) from pin (9).
5. Remove spring (11) from cover (12).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:00:55 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378527
Hydraulic Lockout Control - Assemble
SMCS - 5001-016-LK
Assembly Procedure
Illustration 1 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Install spring (11) to cover (12).
2. Install pin (10) to pin (9).
Illustration 2 g01187383
3. Install pin (7) to pipe assembly (6).
4. Slide cover (8) over pipe assembly (6).
Illustration 3 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Install spring (3), lever assembly (5), and retaining ring (4).
2/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 6. Install lever assembly (2) and retaining rings (1).
End By:
a. Install the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:01:51 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07426591
Hydraulic Lockout Control - Install
SMCS - 5001-012-LK
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 243 -
Illustration 1 g01278781
1. Install hydraulic lockout control (3), bolt (4), and bolt (5).
2. Apply Tooling (A) to the threads of screws (6). Position switch assembly (7) and install
screws (6). Tighten screws (6) to a torque of 0.7 ± 0.1 N·m (6.2 ± 0.9 lb in). Attach cable
strap (8).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01187398
3. Install panel (1) and screws (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:02:47 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02417256
Operator Console - Remove and Install
SMCS - 5258-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Start By:
a. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove".
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01208165
1. Remove plates (1) and (2).
Illustration 2 g01196137
2. Attach Tooling (A) and an air supply to the hydraulic oil tank. Apply 345 ± 70 kPa
(50 ± 10 psi) to Tooling (A).
2/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 6. Disconnect harness assemblies (6).
Illustration 7 g01208204
7. Remove plate (8). Move floor mat (7) toward the front of the cab.
Illustration 8 g01208208
8. Remove bolts (9) from each side of the operator console. Pull hose assemblies (3) and (4)
through the floor of the cab. Hose assemblies (3) and (4) were removed in Steps 3 and 4.
Pull harness assemblies (5) and (6) through the floor of the cab. Harness assemblies (5) and
(6) were removed in Steps 5 and 6.
Note: If the machine is equipped with a radio, the antenna will need to be disconnected.
4/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 9 g01208250
9. Disconnect harness assembly (10).
Illustration 10 g01208252
10. Remove bolts (11) and operator console (12).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Illustration 11 g01208252
1. Install operator console (12) and bolts (11).
5/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 12 g01208250
2. Connect harness assembly (10).
Illustration 13 g01208208
3. Insert hose assemblies (3) and (4) through the hole in the cab floor. Insert harness
assemblies (5) and (6) through the holes in the cab floor. Hose assemblies (3) and (4) and
harness assemblies (5) and (6) will be connected in the following steps. Install bolts (9)
from each side of the operator console.
Note: If the machine is equipped with a radio, the antenna will need to be connected.
Illustration 14 g01208204
6/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 4. Move floor mat (7) toward the rear of the cab. Install plate (8).
Illustration 15 g01208202
5. Connect harness assemblies (6).
Illustration 16 g01208198
6. Connect harness assemblies (5).
Illustration 17 g01208191
7. Connect hose assemblies (4).
7/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...