1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Precise alignment and torque specifications are noted.
Caterpillar cat 330 c l excavator (prefix dky) service repair manual (dky0000...hhjsekmdmm
The document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists 28 steps for disassembly, removing components like the head, plates, seals, and bearing races. It then lists 28 steps for assembly, reinstalling those components in reverse order and noting requirements like applying thread lock compounds and ensuring proper alignment of parts. Tools required are also listed. The overall document provides a detailed technical procedure for fully disassembling and reassembling the excavator's travel motor.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix dky) service repair manual (dky0000...hhjsekmdmm
The document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists 28 steps for disassembly, removing components like the head, plates, seals, and bearing races. It then lists 28 steps for assembly, reinstalling those components in reverse order and noting requirements like applying thread lock compounds and ensuring proper alignment of parts. Tools required are also listed. The overall document provides a detailed technical procedure for fully disassembling and reassembling the excavator's travel motor.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d excavator (prefix ern) service repair manual (ern00001 ...hhjsekmdmm
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 31 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg total weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 336 d l excavator (prefix myg) service repair manual (myg0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...hhjsekmdmm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
Caterpillar cat 330 f excavator (prefix lbn) service repair manual (lbn00001 ...fjskekdmjekm
The document provides instructions for disassembling a 330F LN excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, housing assembly, brake piston, friction discs, rotating group, pistons, and other internal parts. Detailed illustrations are provided to accompany each step of the disassembly process. Safety notices are included throughout to warn of potential hazards like released spring forces.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...diskdkkdmmd
This document provides instructions for removing and installing a crankshaft rear seal on a 330D L excavator. The removal procedure involves removing the flywheel and then removing the crankshaft rear seal and bolts. The installation procedure specifies cleaning and preparing surfaces, applying sealant, and installing the seal with bolts in a specified tightening sequence. Tools and inspection guidelines are also referenced.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...diskdkkdmmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...diskdkkdmmd
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d l excavator (prefix mwp) service repair manual (mwp0000...diskdkkdmmd
This document provides disassembly and assembly instructions for a 330D L excavator final drive. It lists required tools and steps to remove the travel motor, drain oil, remove the final drive sprocket, cover, carrier assemblies, springs and other components. Detailed illustrations accompany each step to disassemble the planetary gear assemblies, shafts, rings, and other parts of the final drive. Proper safety procedures are noted to relieve spring pressure before removing retaining rings.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...diskdkkdmmd
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts.
3. Removing sealing rings and the counterbalance valve.
4. Reinstalling involves the reverse of removal steps, including applying anti-seize compound and tightening bolts to the specified torque.
Caterpillar cat 330 d l excavator (prefix jlp) service repair manual (jlp0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts thoroughly before disassembly to prevent dirt intrusion.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d excavator (prefix ern) service repair manual (ern00001 ...hhjsekmdmm
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 31 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg total weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 336 d l excavator (prefix myg) service repair manual (myg0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...hhjsekmdmm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
This document provides the disassembly and assembly procedures for a travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 30 steps to disassemble the travel motor down to its core components. It then provides 19 steps to reassemble the travel motor. The document includes illustrations and notes on proper assembly order and tooling required. Safety precautions are provided throughout for tasks involving spring tension or component installation.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
Caterpillar cat 330 f excavator (prefix lbn) service repair manual (lbn00001 ...fjskekdmjekm
The document provides instructions for disassembling a 330F LN excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, housing assembly, brake piston, friction discs, rotating group, pistons, and other internal parts. Detailed illustrations are provided to accompany each step of the disassembly process. Safety notices are included throughout to warn of potential hazards like released spring forces.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...diskdkkdmmd
This document provides instructions for removing and installing a crankshaft rear seal on a 330D L excavator. The removal procedure involves removing the flywheel and then removing the crankshaft rear seal and bolts. The installation procedure specifies cleaning and preparing surfaces, applying sealant, and installing the seal with bolts in a specified tightening sequence. Tools and inspection guidelines are also referenced.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...diskdkkdmmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...diskdkkdmmd
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d l excavator (prefix mwp) service repair manual (mwp0000...diskdkkdmmd
This document provides disassembly and assembly instructions for a 330D L excavator final drive. It lists required tools and steps to remove the travel motor, drain oil, remove the final drive sprocket, cover, carrier assemblies, springs and other components. Detailed illustrations accompany each step to disassemble the planetary gear assemblies, shafts, rings, and other parts of the final drive. Proper safety procedures are noted to relieve spring pressure before removing retaining rings.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...diskdkkdmmd
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts.
3. Removing sealing rings and the counterbalance valve.
4. Reinstalling involves the reverse of removal steps, including applying anti-seize compound and tightening bolts to the specified torque.
Caterpillar cat 330 d l excavator (prefix jlp) service repair manual (jlp0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts thoroughly before disassembly to prevent dirt intrusion.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...diskdkkdmmd
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly and inspecting O-rings and seals for wear. The assembly process involves installing seals and O-rings into the outside housing, positioning the rotor inside the housing, and attaching the housing to the rotor with bolts and washers. Proper cleanliness is emphasized throughout the assembly.
Caterpillar cat 330 d l excavator (prefix gbc) service repair manual (gbc0000...diskdkkdmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 d l excavator (prefix ern) service repair manual (ern0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
Caterpillar cat 330 d l excavator (prefix edx) service repair manual (edx0000...diskdkkdmmd
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housing components, and fasteners in the proper sequence. The assembled swing drive is then installed on the excavator frame using lifting equipment and bolted into place with an alternating tightening pattern to the specified torque.
Caterpillar cat 330 d l excavator (prefix eah) service repair manual (eah0000...diskdkkdmmd
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 total parts from the swing drive including covers, gears, carriers, shafts and seals. The assembly procedure instructs installing these 17 parts in reverse order and includes cleaning and lubricating components before assembly. Tools required include link brackets, nylon slings and pliers.
Caterpillar cat 330 d fm excavator (prefix l2k) service repair manual (l2k000...diskdkkdmmd
This document provides installation instructions for a travel motor on a 330D FM excavator. It includes:
- Cleaning the mating surfaces of the travel motor and final drive.
- Using guide bolts and lifting devices to position the travel motor, then installing securing bolts.
- Connecting hose assemblies and tightening to the specified torque.
- Using guide bolts and two people to position the heavy cover, then installing and tightening cover bolts.
Caterpillar cat 330 d fm excavator (prefix e4k) service repair manual (e4k000...diskdkkdmmd
This document provides disassembly instructions for the final drive of a 330D FM excavator. It lists required tools and outlines 33 steps to fully disassemble the final drive. These include removing the travel motor, draining oil, removing the sprocket, cover, carrier assemblies, gears, springs and other components. Detailed illustrations are provided to show how to remove retaining rings, shafts, plates and other parts using various specialty tools. Safety precautions are noted regarding relieving spring pressure and containing fluids.
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...diskdkkdmmd
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...diskdkkdmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It describes:
1) Removing the rocker arm shaft, front cover, and valve lifters before removing the camshaft.
2) Aligning timing marks and removing bolts and thrust plate to access the camshaft.
3) Lubricating and carefully installing the camshaft, rotating it to prevent binding in the bearings.
Caterpillar cat 330 d excavator (prefix ern) service repair manual (ern00001 ...diskdkkdmmd
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg total weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...diskdkkdmmd
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housing components, and fasteners in the proper sequence. The assembled swing drive is then installed on the excavator frame using lifting equipment and bolted into place with an alternating tightening pattern to the specified torque.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...diskdkkdmmd
This document provides instructions for disassembling and assembling the swing drive of excavator models 330D and 330D L. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper cleaning and lubrication of parts is emphasized for correct reassembly.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C L EXCAVATOR JAB
Configuration: 330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 2 16:00:49 UTC+0800 2020
11/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C L EXCAVATOR JAB
Configuration: 330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. 5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
5/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 15 g00887501
Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
10/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 2 16:01:44 UTC+0800 2020
11/11(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C L EXCAVATOR JAB
Configuration: 330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02372696
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 1 g00878123
2. Install new O-ring seal (5) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Fasten a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/3(W)
w
2020/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...