The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove the assembly, the alternator belt must first be removed. Torx screws are then removed using a socket while the crankshaft is prevented from rotating. The assembly can be removed, along with a friction shim if needed. For installation, the components are reassembled in reverse order using guide studs, bolts, and a torque wrench. Proper alignment of parts is emphasized to ensure correct assembly.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...hfjsekekmmd
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...hfjsekekmmd
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3300 dt gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for parts books. It explains the column headings used on parts pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included to indicate part differences between countries. The document then provides an example page from a parts book listing parts for an engine crankcase.
Kubota l3130 hst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l3130 gst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It also notes country codes that may be included, such as exceptions for parts in other countries like France (FR). Diagrams of product parts are indexed for locating specific components.
Kubota l3130 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l2900 f tractor parts catalogue manualdfjjsjkemmm
This document provides an index and part listings for an L2900F product. It includes sections for the engine, fuel system, cooling water system, electrical system, clutch, transmission, rear axle, brake, front axle, steering, hydraulic system, hood, labels, and accessories. Each section lists the relevant part numbers, descriptions, quantities, and other specifications for the individual components.
Kubota l2900 dt tractor parts catalogue manualdfjjsjkemmm
The crankcase parts list includes over 230 individual parts that make up the crankcase assembly. It lists each part number, description, quantity used, applicable serial number range, interchangeability, remarks, and weight. Key details included are the total weight of the assembled crankcase (48.5kg/106.7lbs) and that most common individual parts like plugs and seals weigh only a few grams.
Kubota l2800 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using a parts book for a tractor model. It defines the column headings used on parts number pages, including the part reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate if a part is different for other countries. The document then provides an index of parts for the tractor model with the part number and relevant parts book for each item.
Kubota l2800 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using parts books and describes the column headings used on parts number pages. It explains that country codes may be included to indicate if a part is different for other countries. Finally, it lists frequently used parts for a L2800DT/HST tractor, including the part number, description, and reference book for each part.
Kubota l2600 dt tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a cylinder head. It includes a list of 170 parts with information on the part number, description, quantity used, applicable serial number range, interchangeability, and remarks. It notes country codes that may be relevant for part interchangeability between countries like the US, Canada, France, etc. The total weight of the cylinder head component is provided at the end.
Kubota l2500 f tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It lists the column headings used on parts pages including the reference number, part number, description, quantity, serial number range and other details. It then provides an example page from the parts book with over 250 individual part numbers listed for the crankcase component.
Kubota l2500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books. It defines the column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for (e.g. A for USA, CA for Canada, FR for France). An example page from a parts book is then shown listing parts for an engine crankcase, with the corresponding information for each part.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Kubota m5500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part listings for a parts book. It defines the column headings used on part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country. The summary lists the main document sections and provides an example part listing for a crankcase.
Kubota m5040 hdc tractor parts catalogue manualdfjjsjkemmm
The document provides parts information for an engine, including:
- Descriptions of column headings for part number pages like part number, name, quantity, etc.
- Parts lists organized by component (e.g. crankcase, oil pan, cylinder head) with part numbers, names, quantities, and other details.
- Notes on country codes used for parts that may differ between countries.
Kubota l4610 dt hst tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a crankcase, including the crankcase itself along with various plugs, caps, pins, and other component parts. Key information includes the part number, description, quantity used, applicable serial number range, interchangeability, and remarks.
Kubota l4400 h tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including reference number, part number, part name, quantity, serial number range, and remarks. It notes country codes that may be included and what they indicate. Sample pages from the parts book are then provided that list part numbers, descriptions, quantities and other details for specific assembly items like the crankcase, oil pan, cylinder head, gear case and more.
Kubota l4310 dt gst-chst-c tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and definitions for parts books. It explains that the parts book headings will match the picture pages. It defines the column headings for part number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate part differences by country.
Kubota l3410 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3410 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions and definitions for parts books. It explains the column headings used on parts number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes that may be included are also defined. An example page from the parts book is then shown listing specific part numbers, descriptions, and the book they can be found in.
Kubota l3300 dt gst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for parts books. It explains the column headings used on parts pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included to indicate part differences between countries. The document then provides an example page from a parts book listing parts for an engine crankcase.
Kubota l3130 hst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l3130 gst tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It also notes country codes that may be included, such as exceptions for parts in other countries like France (FR). Diagrams of product parts are indexed for locating specific components.
Kubota l3130 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books, including definitions of column headings in parts number pages such as reference number, part number, description, quantity, serial number range. It also notes country codes that may be included for parts that differ by country, such as parts working in all countries except France. The document then provides an index of parts for a tractor model broken down by system such as engine, fuel, electrical, transmission, hydraulics, with part numbers and references to parts books.
Kubota l2900 f tractor parts catalogue manualdfjjsjkemmm
This document provides an index and part listings for an L2900F product. It includes sections for the engine, fuel system, cooling water system, electrical system, clutch, transmission, rear axle, brake, front axle, steering, hydraulic system, hood, labels, and accessories. Each section lists the relevant part numbers, descriptions, quantities, and other specifications for the individual components.
Kubota l2900 dt tractor parts catalogue manualdfjjsjkemmm
The crankcase parts list includes over 230 individual parts that make up the crankcase assembly. It lists each part number, description, quantity used, applicable serial number range, interchangeability, remarks, and weight. Key details included are the total weight of the assembled crankcase (48.5kg/106.7lbs) and that most common individual parts like plugs and seals weigh only a few grams.
Kubota l2800 hst tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using a parts book for a tractor model. It defines the column headings used on parts number pages, including the part reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included to indicate if a part is different for other countries. The document then provides an index of parts for the tractor model with the part number and relevant parts book for each item.
Kubota l2800 dt tractor parts catalogue manualdfjjsjkemmm
This document provides instructions for using parts books and describes the column headings used on parts number pages. It explains that country codes may be included to indicate if a part is different for other countries. Finally, it lists frequently used parts for a L2800DT/HST tractor, including the part number, description, and reference book for each part.
Kubota l2600 dt tractor parts catalogue manualdfjjsjkemmm
This document provides part numbers and descriptions for a cylinder head. It includes a list of 170 parts with information on the part number, description, quantity used, applicable serial number range, interchangeability, and remarks. It notes country codes that may be relevant for part interchangeability between countries like the US, Canada, France, etc. The total weight of the cylinder head component is provided at the end.
Kubota l2500 f tractor parts catalogue manualdfjjsjkemmm
The document provides instructions and part numbers for a parts book. It lists the column headings used on parts pages including the reference number, part number, description, quantity, serial number range and other details. It then provides an example page from the parts book with over 250 individual part numbers listed for the crankcase component.
Kubota l2500 dt tractor parts catalogue manualdfjjsjkemmm
The document provides instructions for parts books. It defines the column headings used on parts number pages, including reference number, part number, description, quantity, serial number range, interchangeability, and remarks. Country codes are also explained, with symbols indicating the country each part is for (e.g. A for USA, CA for Canada, FR for France). An example page from a parts book is then shown listing parts for an engine crankcase, with the corresponding information for each part.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018640
Rear Power Take-Off (RPTO) - Remove
SMCS - 1165-011-RE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the
correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. If necessary, remove the OEM equipment from the rear power take-off (RPTO).
1/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g02069019
Illustration 2 g02069023
2. Remove bolts (1). Remove adapter (2) from flywheel housing (9). Remove O-ring seal (3)
(not shown).
2/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Note: Make a temporary mark on the adapter and the flywheel housing in order to show the
correct orientation of the adapter.
3. Remove bolts (4). Remove adapter (5) from flywheel housing (9). Remove O-ring seal (6)
(not shown).
Note: Make a temporary mark on the adapter and the flywheel housing in order to show the
correct orientation of the adapter.
4. Remove gear (7) from crankshaft (8).
5. If necessary, follow Steps 5.a through Steps 5.b in order to remove the sleeve bearing from
the adapter.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (10) from
adapter (2).
6. Repeat Steps 6.a through Step 6.b in order to remove the sleeve bearing from adapter (5).
a. Place adapter (5) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (10) from
adapter (5).
Illustration 3 g02069020
3/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. 7. Remove gear assembly (11) and gear assembly (12) from flywheel housing (9).
Illustration 4 g02069021
Illustration 5 g02069453
8. Remove bolts (13). Remove gear (17) and idler hub (15) from flywheel housing (9).
4/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. 9. Remove bolts (14). Remove gear (18) and idler hub (16) from flywheel housing (9).
10. If necessary, follow Steps 10.a through Steps 10.b in order to remove the sleeve bearing
from the gear.
a. Place gear (17) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (19) from gear
(17).
Illustration 6 g03453499
11. Repeat Steps 11.a through Step 11.b in order to remove the sleeve bearing from the
remaining gear.
a. Place gear (18) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (19a) from
gear (18).
5/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 7 g02069024
12. If necessary, follow Steps 12.a through Steps 12.b in order to remove the sleeve bearings
from the flywheel housing.
a. Use a suitable tool in order to remove sleeve bearing (20) from flywheel housing (9).
b. Repeat Step 12.a in order to remove sleeve bearing (21) from flywheel housing (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:22:20 UTC+0800 2020
6/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018641
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components of the rear power take-off (RPTO) are clean and free from wear
and damage.
1/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 2 g02069024
2. If necessary, follow Steps 2.a through Steps 2.c in order to install the sleeve bearings from
the flywheel housing.
a. Accurately align oil Holes (X) in sleeve bearing (20) with the oil holes in flywheel
housing (9).
b. Use Tooling (A) in order to install sleeve bearing (20) into flywheel housing (9).
Note: Ensure that the oil holes are correctly aligned. If the oil holes are not correctly
aligned, the sleeve bearing should be removed.
c. Repeat Step 2.a through Steps 2.b in order to install sleeve bearing (21) to flywheel
housing (9).
3/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 3 g02070455
3. If necessary, follow Steps 3.a through Steps 4 in order to install the sleeve bearing to the
gears.
a. Place gear (17) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (19) with Grooves (Y) in gear (17).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19) into gear
(17).
4/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 4 g03453500
4. Repeat Steps 3.a through Step 3.c in order to install the sleeve bearing to gear (18).
a. Place gear (18) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (19a) with Grooves (Y) in gear (18).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19a) into gear
(18).
5/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Illustration 5 g02069021
5. Lubricate idler hub (15) and gear (17) with clean oil. Install idler hub (15) to gear (17).
Note: Ensure that the gear and the idler hub are correctly oriented.
6. Install gear (17) and idler hub (15) assembly to flywheel housing (9).
Note: Ensure that the oil hole in the idler hub is correctly positioned.
7. Install bolts (13) to idler hub (15) and hand tighten bolts.
Note: Ensure that the idler hub is correctly aligned to the flywheel housing.
8. Repeat Steps 5 through Step 7 in order to install gear (18), idler hub (16) and bolts (14) to
flywheel housing (9).
9. Tighten bolts (13) and bolts (14) to a torque of 100 N·m (74 lb ft).
10. Ensure that there is tactile backlash between gear (17) and gear (18). Ensure that there is
end play between the idler hubs and the gears.
6/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 6 g02069020
11. install gear assembly (11) and gear assembly (12) to flywheel housing (9).
7/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 8 g02070473
12. If necessary, follow Steps 12.a through Steps 12.c in order to install the sleeve bearings to
the adapters.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to install sleeve bearing (10) into
adapter (2).
c. Repeat Steps 12.a through Step 12.b in order to install the sleeve bearing into adapter
(5).
13. Install a new O-ring seal (3) (not shown) to adapter (2).
14. Install adapter (2) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
15. Install bolts (1) and tighten the bolts to a torque of 55 N·m (41 lb ft).
16. Install a new O-ring seal (6) (not shown) to adapter (5).
17. Install adapter (5) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
18. Install bolts (4) and tighten the bolts to a torque of 55 N·m (41 lb ft).
9/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 19. Ensure that there is tactile backlash between the gears. Ensure that there is end play between
the gears and the flywheel housing and the adapters.
20. Install gear (7) to crankshaft (8).
21. If necessary, install the OEM equipment to the rear power take-off (RPTO).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:23:16 UTC+0800 2020
10/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909511
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Remove Tooling (A) .
2/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:24:11 UTC+0800 2020
3/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909517
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.f in order to install vibration damper, crankshaft
pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Remove Tooling (D) .
f. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Jul 6 09:25:07 UTC+0800 2020
3/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018646
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly 1
2/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03417117
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...