Caterpillar cat c18 industrial engine (prefix wjh) service repair manual (wjh00001 and up)

Service Repair Manual
Models
C18 Industrial Engine

Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJH
Configuration: C18 Industrial Engine WJH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02954434
Rocker Arm and Shaft - Remove
SMCS - 1102-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 124-2946 Lifting Bracket 1
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
B. Remove the variable valve actuator, if necessary. Refer to Disassembly and Assembly,
"Valve Actuator (Variable) - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g01047470
Valve rocker arms and unit injector rocker arms can move on the shaft
after the bolts have been removed. The shaft should be kept level when
removed from the cylinder head. To avoid possible personal injury,
keep fingers clear of the valve rocker arms and the unit injector rocker
arms when lifting the assembly from the cylinder head.
1. Remove bolts (2) .
2. Use Tooling (A) to remove rocker arm shaft assembly (4) , valve rocker arms (3) , and
electronic unit injector rocker arms (1) as a unit.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 20:32:51 UTC+0800 2020
2/2(W)
w
2020/6/12

Shutdown SIS
Previous Screen
i04997049
Rocker Arm - Disassemble
SMCS - 1123-015
Disassembly Procedure
Start By:
a. Remove the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Remove".
NOTICE
1/2(W)
w
2020/6/12

1. Remove valve rocker arms (11) and electronic unit injector rocker arm (3) from rocker shaft
assembly (4).
2. Remove jam nut (7) from adjustment screw (8).
3. Remove adjustment screw (8) from valve rocker arms (11).
4. Remove button (10) from adjustment screw (8). Remove O-ring seal (9) from the
adjustment screw.
5. Remove jam nut (2) from unit injector adjustment screw (1).
6. Remove unit injector adjustment screw (1) from electronic unit injector rocker arm (3).
7. Remove button (6) from unit injector adjustment screw (1). Remove O-ring seal (5) from
the unit injector adjustment screw.
Fri Jun 12 20:33:47 UTC+0800 2020
2/2(W)
w
2020/6/12

Shutdown SIS
Previous Screen
i04998150
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
NOTICE
1/2(W)
w
2020/6/12

Note: Do not reuse the O-ring seal on the adjustment screw if the button is removed from
the adjustment screw.
1. Install O-ring seal (9) in button (10).
2. Use a soft hammer to seat button (10) on adjustment screw (8).
3. Install adjustment screw (8) in valve rocker arms (11). Install jam nut (7) on the adjustment
screw.
4. Install O-ring seal (5) in button (6).
5. Use a soft hammer to seat button (6) on unit injector adjustment screw (1).
6. Install unit injector adjustment screw (1) in electronic unit injector rocker arm (3). Install
jam nut (2) on the unit injector adjustment screw.
7. Lubricate rocker shaft assembly (4) with clean engine oil.
8. Install valve rocker arms (11) and electronic unit injector rocker arm (3) on rocker shaft
assembly (4).
End By:
a. Install the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Install".
Fri Jun 12 20:34:42 UTC+0800 2020
2/2(W)
w
2020/6/12

Shutdown SIS
Previous Screen
i07394739
Rocker Arm and Shaft - Install
SMCS - 1102-012
Installation Procedure
Table 1
Required Tools
A 124-2946 Lifting Bracket 1
NOTICE
1/3(W)
w
2020/6/12

1. Position rocker arm shaft assembly (4), valve rocker arms (3), and electronic unit injector
rocker arms (1) as a unit with Tooling (A) on the cylinder head.
Note: Apply clean engine oil to the underside of the bolt heads prior to installation.
2/3(W)
w
2020/6/12

2. Install bolts (2) and tighten to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Tighten bolts (2) again
to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Turn bolts (2) for an additional 60 ± 5 degrees.
Tighten the bolts in the following sequence: 2, 3, 1, 4.
3. Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit
Injector - Adjust".
4. Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash-
Inspect/Adjust".
End By:
a. Install the variable valve actuator, if necessary. Refer to Disassembly and Assembly, "Valve
Actuator (Variable) - Install".
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Fri Jun 12 20:35:38 UTC+0800 2020
3/3(W)
w
2020/6/12

Shutdown SIS
Previous Screen
i03192604
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the aftercooler, if necessary. Refer to Disassembly and Assembly, "Aftercooler -
Remove".
b. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
c. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
d. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
e. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
f. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install ".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/5(W)
w
2020/6/12

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1. Remove bolts (2) and thrust plate (1).
2/5(W)
w
2020/6/12

2. Remove sealing plate (3) and adapter assembly (4).
3. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/5(W)
w
2020/6/12

4. Disconnect hose assembly (8) at the cylinder head. Remove the bolt and the clip that secures
the hose assembly to the front housing. Remove the bolt and the clip that secures the hose
assembly to the cylinder head.
5. Disconnect hose assembly (9) at the cylinder head.
6. Remove bolt (14) and the breather tube from the cylinder head.
7. Remove bolts (7) and remove the bracket from the cylinder head.
8. Disconnect boost pressure sensor (10).
9. Disconnect inlet air temperature sensor (13).
10. Remove bolts (12) and remove air inlet elbow (11) from the cylinder head, if necessary.
Remove the gasket from the cylinder head.
4/5(W)
w
2020/6/12

11. Attach a suitable lifting device to cylinder head (16). The weight of cylinder head (16) is
approximately 235 kg (518 lb). Ensure that all of the following items are clear from the
cylinder head: harness assemblies, tube assemblies and hose assemblies.
12. Remove cylinder head bolts (15).
13. Carefully remove cylinder head (16).
14. Remove cylinder head gasket (17).
15. Remove spacer plate (18).
16. Remove seals (22) and seal (20).
17. Remove spacer plate gasket (21).
18. Remove O-ring seal (19) from the dowel in the cylinder block.
Fri Jun 12 20:36:34 UTC+0800 2020
5/5(W)
w
2020/6/12

Shutdown SIS
Previous Screen
i03192802
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
A 4C-5592 Anti-Seize Compound -
B 8T-2998 Lubricant -
C 9S-3263 Thread Lock Compound -
NOTICE
1/6(W)
w
2020/6/12

Note: Thoroughly clean the spacer plate and the bottom surface of the cylinder head and the
top of the cylinder block. A new spacer plate gasket and a cylinder head gasket must be
installed when the cylinder head is removed.
1. Install O-ring seal (19) on the dowel in the cylinder block.
2. Install spacer plate gasket (21) on the cylinder block.
3. Install spacer plate (18).
4. Install seals (22) and seal (20).
5. Install cylinder head gasket (17) on the spacer plate.
2/6(W)
w
2020/6/12

6. Attach a suitable lifting device to cylinder head (16). The weight of cylinder head (16) is
approximately 235 kg (518 lb).
7. Carefully install the cylinder head on the dowel pins on the cylinder block.
8. Apply Tooling (A) to the threads of cylinder head bolts (15) and both sides of the washers.
Install cylinder head bolts (15).
Note: The bolts that are Marked "X" are 216 mm (8.5 inch) long: 11, 12, 13, 14, 16, 18, 20,
22, 24 and 26. The rest of the bolts are 194 mm (7.6 inch) long.
9. Tighten the cylinder head bolts according to the following procedure.
a. In a numerical sequence, tighten Bolts 1 through 26 to a torque of 270 ± 15 N·m
(200 ± 11 lb ft).
b. In a numerical sequence, tighten Bolts 1 through 26 to a torque of 450 ± 15 N·m
(330 ± 11 lb ft).
c. In a numerical sequence, again tighten Bolts 1 through 26 to a torque of
450 ± 15 N·m (330 ± 11 lb ft).
3/6(W)
w
2020/6/12

10. Position the gasket and air inlet elbow (11) on the cylinder head and install bolts (12), if
necessary.
11. Connect hose assembly (9) at the cylinder head.
12. Connect hose assembly (8) at the cylinder head. Install the bolt and the clip that secures the
hose assembly to the front housing. Install the bolt and the clip that secures the hose
assembly to the cylinder head.
13. Position the breather tube on the cylinder head and install bolt (14). Tighten the bolt to a
torque of 10 ± 3 N·m (89 ± 27 lb in).
14. Position the bracket on the cylinder head and install bolts (7).
15. Connect inlet air temperature sensor (13).
16. Connect boost pressure sensor (10).
4/6(W)
w
2020/6/12

17. Install O-ring seal (5) and O-ring seal (6) on sealing plate (3). Lubricate O-ring seal (6) with
a 50/50 mixture of Tooling (B) and clean engine oil.
5/6(W)
w
2020/6/12

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

18. Install adapter assembly (4) and sealing plate (3). Ensure that the dowel in adapter assembly
(4) engages the hole in the camshaft.
Note: Ensure that the O-ring seal stays in the groove in sealing plate (3).
19. Install thrust plate (1) . Apply Tooling (C) to bolts (2). Hold the thrust plate in position and
install bolts (2). Evenly tighten bolts (2) until sealing plate (3) and the O-ring seal are seated
against the cylinder head.
End By:
a. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
c. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
d. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
e. Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
f. Install the aftercooler, if necessary. Refer to Disassembly and Assembly, "Aftercooler -
Install".
Fri Jun 12 20:37:30 UTC+0800 2020
6/6(W)
w
2020/6/12

Shutdown SIS
Previous Screen
i02535176
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Table 1
Required Tools
A 9U-7257 Cradle 1
B 9U-7256 Guide 1
C 9U-7225 Camshaft Pilot 2
D 9U-7240 Camshaft Hook 2
Start By:
a. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Remove the rocker arms and the rocker shafts. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Remove".
NOTICE
1/10(W)
w
2020/6/12

NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1. Remove bolts (2) and thrust plate (1).
2/10(W)
w
2020/6/12

Caterpillar cat c18 industrial engine (prefix wjh) service repair manual (wjh00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Caterpillar cat c18 industrial engine (prefix wjh) service repair manual (wjh00001 and up)

Similar to Caterpillar cat c18 industrial engine (prefix wjh) service repair manual (wjh00001 and up) (20)

More from cfvdssd

More from cfvdssd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat c18 industrial engine (prefix wjh) service repair manual (wjh00001 and up)