This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
The document aims to safely depressurize hydraulic systems to allow disconnection of components or lines for maintenance.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
This document provides assembly instructions for a piston pump in a 226B3 skid steer loader. It lists 78 steps to assemble internal components like bearings, seals, springs, and housing pieces. Tools required include rulers, pliers, drivers, pullers, and grease. Proper orientation of dowels, pins, and plates is emphasized. Torque specifications are provided for fittings and valves. The instructions caution that following the steps and wearing protective equipment is important due safety risks from spring-loaded components.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 320 c l 320cl excavator (prefix gla) service repair manual (...ujjdfjkskdme
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and other parts from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, drivers and presses. The process separates all internal components to allow inspection and replacement of parts.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d l hydraulic excavator (prefix ras) service repair manua...jfdskekdmme
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves disconnecting hoses, removing bolts and brackets, and using lifting tools to detach the final drive and travel motor assembly. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling fluids before testing operation. Required tools include vacuum pumps, lifting brackets, and thread sealant for reinstallation.
Caterpillar cat 336 d l excavator (prefix m4t) service repair manual (m4t0000...fksjksmmde
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses, remove bolts and brackets, and lift out the final drive assembly. Detailed steps are provided for removing the travel motor and reinstalling both components along with new O-rings and fasteners. Safety notices advise keeping components clean and containing hydraulic fluids during disassembly.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
This document provides assembly instructions for a piston pump in a 226B3 skid steer loader. It lists 78 steps to assemble internal components like bearings, seals, springs, and housing pieces. Tools required include rulers, pliers, drivers, pullers, and grease. Proper orientation of dowels, pins, and plates is emphasized. Torque specifications are provided for fittings and valves. The instructions caution that following the steps and wearing protective equipment is important due safety risks from spring-loaded components.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 320 c l 320cl excavator (prefix gla) service repair manual (...ujjdfjkskdme
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and other parts from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, drivers and presses. The process separates all internal components to allow inspection and replacement of parts.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 330 d l hydraulic excavator (prefix ras) service repair manua...jfdskekdmme
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves disconnecting hoses, removing bolts and brackets, and using lifting tools to detach the final drive and travel motor assembly. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling fluids before testing operation. Required tools include vacuum pumps, lifting brackets, and thread sealant for reinstallation.
Caterpillar cat 336 d l excavator (prefix m4t) service repair manual (m4t0000...fksjksmmde
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses, remove bolts and brackets, and lift out the final drive assembly. Detailed steps are provided for removing the travel motor and reinstalling both components along with new O-rings and fasteners. Safety notices advise keeping components clean and containing hydraulic fluids during disassembly.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
1. The document provides instructions for releasing hydraulic pressure on a 216 Skid Steer Loader. It describes pressing the auxiliary hydraulic control switch while the joystick is in neutral to release pressure from the auxiliary system.
2. It also describes instructions for removing and installing the quick coupler on the skid steer loader. This involves removing pins and bolts to detach the coupler and lifting it off, then reversing the process to install it.
3. Finally, it provides steps for removing and installing the tilt cylinder, which requires removing pins and bolts to detach it from the lift arm assembly and reattaching it by reversing the removal steps.
1. The document provides instructions for releasing hydraulic pressure on a 216 Skid Steer Loader before performing maintenance. It describes pressing the auxiliary hydraulic control switch while the joystick is in neutral to release pressure from the auxiliary system.
2. Steps are provided to remove and install the quick coupler on the skid steer loader. This involves supporting the coupler, removing pins and bolts, and using lifting devices during removal and installation.
3. Procedures describe removing the tilt cylinder from the lift arm assembly of the skid steer loader. This involves removing snap rings and pins, raising the lift arm with supports, and disconnecting hydraulic lines before removing the cylinder.
1. The document provides instructions for removing a lift cylinder from a 216 Skid Steer Loader.
2. It describes releasing hydraulic pressure, tilting the cab, and removing pins and bolts to detach the lift cylinder.
3. Safety precautions are outlined to prevent injury from hydraulic pressure and contain fluids during disassembly.
1. The document provides instructions for removing a lift cylinder from a 216 Skid Steer Loader.
2. It describes releasing hydraulic pressure, tilting the cab, and removing pins and bolts to detach the lift cylinder.
3. Safety precautions are provided to prevent injury from hydraulic pressure and contain fluids during disassembly.
Similar to Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m00001 and up) (13)
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...cdsaas
The document provides instructions for disassembling the piston pump (swing) of an M315C wheeled excavator. It describes removing 22 individual parts from the pump housing including the servo valve, charge pump, gears, head, port plate, relief valves, spool, and adjustment screw. Cleanliness is important when disassembling to prevent dirt from entering the internal mechanisms. Personal injury precautions are also noted regarding hydraulic pressure and spring force.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...cdsaas
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, seals, pistons, and bearings. It then lists the assembly steps in reverse order, noting to clean parts and apply new thread lock before reinstalling components. Precautions are provided to mark parts for orientation and contain fluids during maintenance.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...cdsaas
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...cdsaas
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 27 step process that includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, and other internal components. Special tools are required and components must be marked for proper reassembly in the correct positions. Safety precautions are outlined to contain fluids and handle components carefully.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...cdsaas
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 35 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...cdsaas
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components of significant weight during disassembly. Cleanliness is emphasized to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...cdsaas
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, bearings, brake piston, plates, and seals. It then lists 16 steps for assembly, replacing components in reverse order and noting specifics like lubrication, alignment marks, and press fittings. Precise installation of keys and cam plates is emphasized to prevent damage.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...cdsaas
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly procedure then consists of 27 steps to dismantle the various components of the travel motor, including removing the head, brake piston, barrel assembly, cam plate, and other internal parts. Precautions are provided to properly contain fluids and mark components for reassembly. Required tools are also listed.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...cdsaas
The document provides instructions for disassembling a 330D2 excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Tools required for the disassembly include an adapter, bolts, washers, eyebolt, retaining ring pliers, bearing puller, and shop air. Safety precautions are noted, such as containing fluids and avoiding damage to component surfaces.
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
The document provides instructions for disassembling a 330D2 excavator travel motor. The 27 step procedure includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, seals and other components. Special tools are required and technicians are advised to take care to not damage components and contain fluids.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 35 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various specialized tools are required to disassemble parts and subassemblies. Cleanliness is important to prevent dirt from entering during disassembly.
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, bearings, brake piston, plates, and seals. It then lists 16 steps for assembly, replacing components in reverse order and noting specifics like lubrication, alignment marks, and press fittings. Precise installation of keys and cam plates is emphasized to prevent damage.
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly procedure then consists of 27 steps to dismantle the various components of the travel motor, including removing the head, brake piston, barrel assembly, cam plate, and other internal parts. Precautions are provided to properly contain fluids and mark components for reassembly. Required tools are also listed.
The document provides instructions for disassembling a 330D2 excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Tools required for the disassembly include an adapter, bolts, washers, eyebolt, retaining ring pliers, bearing puller, and shop air. Safety precautions are noted, such as containing fluids and avoiding damage to component surfaces.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...cdsaas
This document provides instructions for removing and installing rear gear group components on a 330D L excavator powered by a C9 engine. The removal process involves using tools to remove retaining bolts and gears. Bearings are removed from adapters using tools as well. Clearances must be checked when installing new bearings. The installation process specifies torques for bolts and using loctite on reused bolts. Dimensions must be matched for bearing installation.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...cdsaas
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like brackets, presses, and hammers/punches. Cleanliness is important to prevent dirt entry during disassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...cdsaas
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Cleanliness is important to prevent contamination. The installation procedure specifies matching angles and distances when pressing bearings in place and lubricating bolts during reinstallation.
The flywheel removal involves using guide studs and lifting equipment due to the flywheel's weight. Removal of the ring gear may require a hammer and punch. Installation specifies heating the ring gear for pressing, applying thread
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...cdsaas
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, shafts, seals, and housing components using various tools while noting weights of parts removed. Detailed illustrations are provided for each step. Cleanliness is important to prevent dirt entry during disassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050091
Air Compressor Drive Gear - Remove
SMCS - 1803-011-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
Start By:
A. Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install Tooling (A) on the air compressor drive gear.
3. Remove nut (2) and washer (3) .
4. Remove air compressor drive gear (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:33:15 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050094
Air Compressor Drive Gear - Install
SMCS - 1803-012-GE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install air compressor drive gear (4) on the air compressor crankshaft.
3. Install washer (3) and nut (2) .
4. Install Tooling (A) on the air compressor drive gear.
5. Tighten nut (2) to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
6. Place a driver which is slightly larger than the nut over the nut and tap the driver with a
hammer.
7. Tighten the nut again to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
End By: Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:34:10 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01897971
Hydraulic System Pressure - Release - Forest Machines
SMCS - 3000-553; 4250-553; 4300-553; 5050-553
S/N - B1K1-UP
S/N - B2L1-UP
S/N - B3M1-UP
S/N - B4N1-UP
Pressure Release Procedure
The release of hydraulic pressure in a hydraulic circuit is required before service is performed to
that hydraulic circuit. Release the pressure in the following hydraulic circuits before any hydraulic
lines are disconnected or removed from that hydraulic circuit.
• Boom hydraulic circuit
• Stick hydraulic circuit
• Heel hydraulic circuit
• Grapple hydraulic circuit
• Swing hydraulic circuit
• Travel hydraulic circuit
• Attachment hydraulic circuits (if equipped)
• Pilot hydraulic circuit
• Return hydraulic circuit
1/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Note: Refer to the Disassembly and Assembly Manual for additional information concerning
service of the components of specific hydraulic circuits.
Release Of Hydraulic Pressure From A Single Hydraulic
Circuit
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from a single hydraulic
circuit of the main hydraulic system.
1. Position the machine on level ground.
2/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that single hydraulic
circuit. This will also release any pressure that might be present in the pilot hydraulic
circuit.
Note: If the desired hydraulic circuit that requires service requires the activation of a switch
for operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Turn the engine start switch to the OFF position.
9. Slowly loosen the filler plug on the hydraulic tank and release the pressure from the
hydraulic tank. Leave the filler plug loose for a minimum of 45 seconds. This will release
the pressure that may be present in the return hydraulic circuit.
10. Tighten the filler plug on the hydraulic tank to the specified torque.
11. The pressure in the single hydraulic circuit that requires service is now released and lines
and components can be disconnected or removed from that hydraulic circuit.
Release Of Hydraulic Pressure From Multiple Hydraulic
Circuits
3/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from multiple hydraulic
circuits of the main hydraulic system.
1. Position the machine on level ground.
4/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that hydraulic circuit.
This will also release any pressure that might be present in the pilot hydraulic circuit.
Note: If the hydraulic circuit that requires service requires the activation of a switch for
operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Start the engine.
9. Place the hydraulic activation control lever in the UNLOCKED position. Do not move any
joysticks or pedals from the NEUTRAL position during this step. Do not activate any
switches during this Step.
10. Return the hydraulic activation control lever to the LOCKED position.
11. Shut off the engine.
12. Repeat Steps 4 through 11 for each additional hydraulic circuit that requires service.
13. After releasing the hydraulic pressure in each of the desired hydraulic circuits, place the
hydraulic activation control lever in the LOCKED position.
5/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 14. Turn the engine start switch to the OFF position.
15. Slowly loosen the filler plug on the hydraulic tank and release the pressure. Leave the filler
plug loose for a minimum of 45 seconds. This will release the pressure that may be present
in the return hydraulic circuit.
16. Tighten the filler plug on the hydraulic tank to the specified torque.
17. The pressure in the multiple hydraulic circuits that require service is now released and lines
and components can be disconnected or removed from those hydraulic circuits.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:35:33 UTC+0800 2020
6/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01694093
Battery - Remove and Install
SMCS - 1401-010
Removal Procedure
Note: This machine contains four batteries. The batteries are connected in series. Mark the
position of both the batteries and the battery cables prior to removal.
1. Open the rear access door on the left side of the machine.
Illustration 1 g00872239
2. Move the battery disconnect switch (1) to the OFF position.
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 2 g00872229
3. Remove nuts (2) from battery covers (3) .
4. Remove battery covers (3) .
Illustration 3 g00872255
5. Move rubber covers (4) from the battery terminal posts.
6. Remove the negative terminals from each of the batteries.
7. Remove the positive terminals from each of the batteries.
8. Remove the batteries.
Installation Procedure
Note: This machine contains four batteries. The batteries are connected in series. Each battery
MUST be in the correct position in order for correct machine operation.
1. Install the batteries in the correct position.
2. Install the positive terminals on each of the batteries.
3. Install the negative terminals on each of the batteries.
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 6 g00872239
7. Move the battery disconnect switch (1) to the ON position.
8. Close the access door.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:36:28 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692348
Alternator - Remove and Install
SMCS - 1405-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7113 Reverse Ratchet 1
1. Open the hood.
2. Disconnect the positive battery terminal. This will prevent any damage to the wiring or to
the alternator.
Illustration 1 g00871311
3. Disconnect wiring terminals (1), (2), and (3) from the alternator.
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g00871323
4. Insert Tooling (A) in slot (4). Apply downward pressure in order to remove the belt.
Illustration 3 g00871363
5. Remove bolt (5) from the belt guard.
2/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 4 g00871375
6. Remove nut (6) and remove the bolt. Remove the guard.
Illustration 5 g00871388
7. Remove spacer (7) and bolt (8) .
8. Remove alternator (9) .
Installation Procedure
1. Place alternator (9) in position.
Illustration 6 g00871388
2. Install spacer (7) and bolt (8). Remove the alternator.
3/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 7 g00871375
3. Position the guard and install nut (6) .
Illustration 8 g00871363
4. Install bolt (5) in the belt guard.
Illustration 9 g00871323
5. Insert Tooling (A) in slot (4). Apply downward pressure in order to install the belt.
4/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 10 g00871311
6. Connect wiring terminals (1), (2), and (3) to the alternator.
7. Connect the positive battery terminal.
8. Close the hood.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:37:24 UTC+0800 2020
5/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692671
Electric Starting Motor - Remove and Install
SMCS - 1453-010
Removal Procedure
1. Disconnect the battery cables.
Illustration 1 g00871495
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g00871498
2. Place an index mark on all of the electrical wires that are connected to the electric starting
motor. Disconnect the electrical wires from the electric starting motor.
Illustration 3 g00871501
3. Remove top starter bolt (1) .
Illustration 4 g00871506
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 4. Remove bottom starter bolts (2) and use a hoist and a lifting sling to remove starter (3). The
weight of the starter is approximately 32 kg (70 lb).
Installation Procedure
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket on the electric starting motor.
Illustration 5 g00871506
3. Use a hoist and a lifting sling to position starter (3) and install bottom starter bolts (2). The
weight of the starter is approximately 32 kg (70 lb).
Illustration 6 g00871501
4. Install top starter bolt (1) .
3/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 7 g00871495
Illustration 8 g00871498
5. Connect all of the electrical wires to the electric starting motor by using the index marks.
6. Connect the battery cables.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:38:20 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692852
Fuel Filter (Primary) and Fuel Filter Base - Remove and
Install
SMCS - 1261-010; 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench As 1
B
6V-9508 Face Seal Plug (11/16 inch by 16 THD) 2
6V-9829 Cap Assembly (11/16 inch by16 THD) 2
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire. To help prevent possible injury, turn the start switch off
when changing fuel filters or water separator elements. Clean up fuel
spills immediately.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...