How to install the outdoor bamboo decking ,take a look ,this instruction file may be help you a lot.

1. Installation method of 3mm clips
(outdoor decking)
A01 3mm clips
A02 2.5mm screws
A03 4mm screws
A04 1.5mm grommet
B01 Screw driver
B02 Band tape
B03 Hammer
B04 Electronic drill
安装所需工具：螺丝刀，卷尺，榔头，电钻
*******************************************************************************
Installation
1. 打扫铺装场地
1.Clean the job site
2. 确定龙骨间距，推荐距离 465mm
2. Fixed the keels, the recommended
space between two keels is 465mm.
(no more than 500mm)

2. 3. 安装第一块地板，选择钉装法。先用电
钻在需要的位置打出预留孔。
3. Installation the first plank by nail
installation. Drill a hole in the first
plank by electric drill.
4. 把大螺钉插入到预留孔中
4. Insert the 4mm screw into the hole of
first plank.
5. 垫片要放在对应的背面位置
5. Put the grommet at the back of the
decking accordingly

3. 6. 如图所示把大螺丝拧到龙骨上
6.Nail down the 4mm screws on keels.
7. 第一片板安装完毕
7.Finish the installation of the first plank.
8. 将扣件安装在第一块板的另外一边的榫
头
8.Put the clips at the other side of decking
as the show in the photo.

4. 9. 将扣件如图插入样板隼槽里，留出的圆孔
用于螺钉固定，固定扣件
9.Fix the clip on keels by 2.5mm screws in
hole of clips.
10. 扣件安装好后的效果
10.Finish the clips installation of the first
plank.
11. 安装第二片地板
11.Install the second plank.

5. 12. 将第二片板按着扣件往里面推，并轻轻的
敲击，使其隼槽可以卡进扣件里
12.Push the second plank according to
the fixed clips and hammer it softly.
13.完成第二片安装
13. Finish the installation of the second
Plank.
14.完成所有的地板安装
14. Finish the installation of all decking by
same method as above.

6. 15.最后收尾的样板同样要使用钉装法，先用
电钻打出预孔（同第一块板的方法）
15.Install the final plank by 4mm screws.
The method is same as the installation
way of first plank. （Drill a hole in the
plank by electric drill. Insert the 4mm
screw into the hole of plank. Put the
grommet at the back of the decking
accordingly. Nail down the 4mm
screws on keels.）

7. *************************************************************************************************
Installation of head-side of bamboo decking
1. 当两片板对接时，必须按图中所示留出
相应的位置。
1. When install the head-side of decking,
leave some space on head-side(see
chart)
2. 如两片对接必须要放在一根龙骨上，必
须按图所示，安装两颗扣件来固定相应
的板。
2.If the head-sides for two plank should be
installed on one keel, please use two clips
to fix the two ends (see chart).
3. 禁止使用一颗扣件固定两块板的端头
3.Forbid to use one clip to fix two ends of
two planks.

8. *************************************************************************************************
Note:
There are total three nail holes on clips.
One hole is used to fix the decking on
keels. And the other two is used to fix the
clip on decking.
扣件上有三个孔，一个孔用来固定在龙骨
上，另外两个孔是用来固定扣件在板上的。
Drill a hole on decking by electronic drill
and install two screws accordingly.
先用电钻在板上钻两个孔，然后相应的采用
螺丝钉固定。
Remark: Usually, nail down the clips (Hole C03) on keels is enough to fix the
decking stably. If there are special requirement to fix the final plank firmly,
please nail down the clips on decking (Hole C01 & Hole C02) as well.
通常，只需要固定孔 C03 即可将板固定在龙骨上。如需加固最后一块板，可以同时将
扣件的孔 C01&C02 通过螺钉也固定在板身上。