1. These are some of my researches which I provided
- The time cancellation device [four methods]
- Determining when the earthquake and the volcano will happen
- Electrical noise cancellation circuit
- Random signal oscillator
- Positive operation random signal radar
- Forward zener diode
-Ton and Toff cancellation of the electronic circuites
- New MOS and BJT transistor
- Class C small signal amplifier
- MOS P I N transistor
- BJT P I N transistor
- New transistor technology
- Electronic negative resistor
- Changeable car
- Forward director for two cages cars [two methods]
- Train include power station generator
- Automatic motor rewinding
- Random carrier signal sending and receiving wireless A M device
- Positive operation radar cancellation
- Searches on LASER field, pharmacy, medicine manufacturing and rockets
-Generation and amplification of electric power from sea waves
- Indication for carbon brush finishing {two methods}
- Transfer the power to the slip ring with new system {liquid system}
- Getting on max. Speed for the rocket
There Are More And More But If I Found That Can Believe Me.
General preface about some of objectives
2. The Time cancellation Device
INTRODUCTION
It is known that the ability of having accurate results depends on the ability of pursuing, picturing and
recording a certain action in a very small moment.
The results accuracy, first of all, depends on the closeness of the moments of taking the pictures because
this enables us to record an action that begins and finishes in a very small time. This record is characterized with
a very accurate sense achieving very good resolution.
So the existence of a device characterized with a continuous reduction of time will ease our study of the
very short and detailed stages of an action begin and finishes in a very short time.
What catches our attention is the reduction of time in this device is a continuous process this means that
one second can be divided into millions, millions…sections. So we can see apart of the action (a chemical
reaction for instance) this part has happened in minimal time.
Not only the device is characterized with a continuous reduction of time, but also at the same time it can
be controlled in a certain limit of the time to have an accurate detailed picture which is clear and sufficient
enough to study a very little action.
The nature of Time cancellation Device
When I talk about this device concerning its use to picture a chemical reaction, I can say that it can
picture a chemical reduction in a minimal time
These pictures can be recorded at C D of computer. These pictures will form a complete detailed film
which describes how the material is formed or how different materials react to form a news material. So we can
say that this device can pictures the very little stages of the material’s forming process from its partial
ingredients.
Generally I can say that this device can take the place of Dr. Ahmed zweil’s camera in all its uses but
this device exceeds this camera because the reduction of time on it is a continuous process with the ability of
controlling its amount.
The importance of this device will be clear though our knowledge of the importance of Dr. Zweil’s camera.
The Time Cancellation Device applications
1) Studying how the new martial is formed and its formation stages.
2) Studying how the connection happens between the partial ingredients of the
material.
3) Studying the characteristics and the effective factors on their ability of
activation.
2
3. 4) Studying how the material turns from one condition to another. (The change
of the material into carbon when it burns for example)
5) This device is more helpful in the respect of pharmacology and medicine
industries.
6) Studying the living cells and how they do their functions accurately.
7) This device has a great ability in dealing with certain actions that begin and finish
in minimal time.
8) This device gives us a recorded and a complete detailed film of the stages which
the action passes from the beginning to the end.
Determining when the earthquake and the
volcano will happen
All the peoples will be come very happy when they know that there are device
can indicate when the quake and the volcano will happen
This device I don't make it untel now because I need information from geology
scientist and mathematics scientist
now I have designing for all steps that I need it to achieve high a curacy on
determining the actual time that the quake and the volcano will happen on it
Notes
I discovered relationship between
Earthquake followed by volcano and other earthquake not followed by volcano
and the time between the earthquake and the volcano
Also I can know the number of followers
Also I can know which is master and which is the slave {earthquake and the
volcano} and ability of exchanging between them
Also I can determine the degree of the earthquake that will happen
New technology of BJT and
MOSFET transistor to achieve class
C small signal amplifier
It's known that class C amplifier deal with only with signal whose voltage is
more than 0.7 V. it amplifies the signal's part that whose voltage is more than
0.7 V , and so that the signal it self is the bias source of the transistor which
operate as an amplifier
3
4. It's also known that class C amplifier has the highest sufficiency than all the
classes.
it's more sufficiency than class A,class B and class AB amplifiers .it's more
sufficient than all classes because it does not depend on an external electrical
power source but the signal is the source of it's electric power which makes it
does it's operation in an active region {BJT} and on linear region {MOSFET}
Although class C is the most sufficient than all classes. it can't deal with small
signals whose voltage less than 0.7 V so we use class A amplifier to amplify
the small signal but the fault with this class is that it has low sufficiency
because the electric current pass in circuit although no input signal.
Class C small signal amplifier has all the advantages of class A and class C .it
has the advantage of class C sufficiency and it has class A's advantages of
dealing with small signals .and of course this is an important thing in the field
of the different communication instruments .
The specialist in this field will know the great importances of this new
technology
Noise cancellation device
It's known for the workers in the field of wire or wireless communications that
the problem of noise is the greatest problem which prevents the transferring of
the main signal with its all details
The noise which affects on the main signal causes a lot of problems, for
example it's bad influence on the process of quantization in case of transferring
by digital communication
Noise affects on all kinds of communication's systems
This effect varies from one system to another .all communication systems
agree that the problem of noise is the first problem to be put in to consideration
when we think of setting up any system of communication. The nose's causes
are various such as the magnetic fields influence, the electrical fields influence,
lighting and switching on/off the electrical circuits. So theoretically, I have a
certain process which will remove all the noise. and as the theoreticlly
conditions are available in the practical side the results will be satisfactory .and
because the theoretical condition are plain ,available and easy to be applied we
won't be mistaken in saying that this way will remove the noise out of the main
signal completely
This method can be applied on both the wire and wireless communications but
with some simple differences to achieve the the desired results in each system
This method is very simple, cheap and easy to be applied in all levels
4
5. The applications
1-this method can be used in the public systems of wire and wireless
communication
2-it can be used in the systems of military communication because this method
is able to resist the deformation's process on the military instruments
3-this method has a high capacity of dealing with the small signals when it
passes on media full of noise {noisy media}
front direction control for the back truck
.
This method is applied only on the trucks which processed of two parts. This
method makes the back truck un subordinate to the front truck, this only turns
in other cases the back truck will be subordinate to the front truck and this is
the normal case.
This method helps the driver to turn the truck in a narrow turns without
taking a big turning.
It will reduce the accidents and the truck's fall which happens as a result of
driving near holes.
Also the driver can use this method when any of the back truck's front tires is
damaged, it helps the driver to use one tire or two or both of them together
(one tire for each side).
The back truck direction control
This method is similar to the former way but it is simpler and easier than it.
Its function is to make the back truck unsubordinated to the front truck only in
turning in other conditions the truck will be in its normal position
This method is expected to achieve very good and satisfactory results because
as I mentioned before, it is characterised by easiness and smoothness and it has
effective results
Removing the effect of the mobile's hot
spot on the brain
5
6. It is known that the effect of the hot spot's focus on the brain of the speaker
is the bad effect of the mobile.
This method doesn't abolish the hot spot but it removes its focus which is
the source of danger to the speaker of the mobile.
This method helps to remove the hot spot's focus away from the brain of the
speaker. We can control the amount of removing to be in the back side of the
mobile's position on the head of the speaker, so the hot spot will be remains but
without any effect on the speaker.
The amount of removing will be determined by the doctor of nerves and
brain. He will determine a certain level of removing which will remove the
harm away of the speaker's brain.
It worths mentioning that this method doesn't require adding an additional
part to the mobile but only a small modification is carried to do this operation
beside its main task.
6