Generative AI Master Class - Generative AI, Unleash Creative Opportunity - Pe...
AEM
1. MOLDED GASKETS, O-RINGS AND RADIAL SHAFT SEALS
very low sieve residue good mixing and
dispersion properties
long flow time with short
vulcanization time
easy deflashing low compression set good media resistance
(fuel, oil, water, acid)
avoidance of mold fouling
caused by filler
MOLDING / BLACK
Quarter light gasket, nitrosamine reducing; 65 Shore A; EPDM; sulfur cure, injection molding
(K 91-59)
Quarter light gasket, Renault 2 6 07 B1; 60 Shore A; EPDM; sulfur cure, injection / transfer
molding (911 C 152)
Corner molding for sponge seals; 30 Shore A; EPDM; sulfur cure (A.1.4.002)
Quarter light gasket; 50 Shore A; EPDM; sulfur cure (A.4.0.003)
Parts with moderate resistance to lubricants and fuel, thermally stressable 100-130°C; 70
Shore A; CR; injection / transfer molding (T.I.B. 4.1.2)
Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70
Shore A; NBR; sulfur cure (M 630.0/1) (M 630.0/7) (M 630.0/3) (M 630.0/2) (M 630.0/5) (M
630.0/6)
Page 1 of 4
Molded gaskets, o-rings and radial shaft seals - Hoffmann Mineral - Funktional Fillers
9/16/2021
https://www.hoffmann-mineral.com/industries/elastomers/automotive_id27344/molded-ga...
2. Download all
RECOMMENDED PRODUCTS
Sorted by crosslinking agent.
MOLDING / LIGHT-COLORED
Rear light gasket, Bosch VS 15441; 25 Shore A; PNR; sulfur cure, injection molding (RRS 12)
Silencer mounting; 55 Shore A; NR; sulfur cure (RRS 15)
Resistant to Diesel and rape-oil methyl ester (RME); 65 Shore A; HNBR; peroxide cure (RRS
36)
Gasket and O-Ring, Aktifit AM versus carbon black N-550, according to PSA S22 5106; 60
Shore A; AEM; diamine cure (M 621.2/8) (M 621.4/5) (M 621.4/2) (M 621.4/3)
Gasket and O-Ring, Aktifit AM in combination with silica in AEM; 70/80 Shore A; AEM,
diamine cure (AEM 9913) (AEM 9914) (AEM 9919)
Aktifit AM in AEM Seals and Gaskets
Molded NBR Parts for Automotive Oil Seals ASTM D2000 -
Replacement of Carbon Black N990
Name Short Description
SILLITIN N 82 Standard product for non-critical compounds with low requirements.
SILLITIN N 85 Standard product for slightly higher requirements for color and dispersion,
low compression set.
SILLITIN Z 86 Standard product, less wear than Sillitin N products.
SILLIKOLLOID P 87 Higher tensile strength and tear resistance, least wear.
Page 2 of 4
Molded gaskets, o-rings and radial shaft seals - Hoffmann Mineral - Funktional Fillers
9/16/2021
https://www.hoffmann-mineral.com/industries/elastomers/automotive_id27344/molded-ga...
3. Name Short Description
SILFIT Z 91 Same as Sillitin N 85, but with avoidance of mold fouling caused by filler,
greater brightness and color neutrality, less moisture content, improved
dispersion.
Name Short Description
AKTISIL MM Same as Sillitin Z 86, but with higher tensile strength, higher tensile
modulus and lower compression set, better abrasion resistance, improved
chemical resistance.
AKTISIL PF 216 Same as Aktisil MM, but with highest tensile strength and tensile modulus,
lowest compression set, best abrasion resistance, best chemical resistance.
AKTIFIT AM Same as Silfit Z 91, but with higher tensile strength, higher tensile
modulus and lower compression set, better abrasion resistance, improved
resistance.
Name Short Description
AKTISIL VM 56 Same as Sillitin Z 86, but with higher tensile strength, higher tensile
modulus and lower compression set, better abrasion resistance, improved
chemical resistance.
AKTISIL VM 56/89 Same as Aktisil VM 56, but for greater color neutrality requirements and
slightly improved dispersion.
AKTISIL Q Similar to Aktisil VM 56/89 but with less moisture content, lower viscosity,
lower compression set, improved resistance, best product for silicone
rubber.
AKTIFIT VM Same as Silfit Z 91, but with higher tensile strength, higher tensile
modulus and lower compression set, better abrasion resistance, improved
chemical resistance.
Page 3 of 4
Molded gaskets, o-rings and radial shaft seals - Hoffmann Mineral - Funktional Fillers
9/16/2021
https://www.hoffmann-mineral.com/industries/elastomers/automotive_id27344/molded-ga...
4. Name Short Description
AKTIFIT Q Same as Silfit Z 91, but with higher tensile strength, highest tension value
and lowest compression set, better abrasion resistance, improved
chemical resistance.
Name Short Description
AKTIFIT AM Same as Silfit Z 91, but with higher tensile strength, higher tensile
modulus, lower compression set, better abrasion resistance, improved
resistance, improved chemical resistance.
Page 4 of 4
Molded gaskets, o-rings and radial shaft seals - Hoffmann Mineral - Funktional Fillers
9/16/2021
https://www.hoffmann-mineral.com/industries/elastomers/automotive_id27344/molded-ga...